summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/omap5-uevm.dts
Commit message (Collapse)AuthorAgeFilesLines
* ARM: dts: omap5-uevm: Remove pinmux for dmic pinsPeter Ujfalusi2013-10-231-10/+0
| | | | | | | | | | | When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM support got deprecated in favor of uEVM (or Panda5) the content was not validated. Panda5 does not have support for digital microphones so remove the pinmux section for it. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmuxPeter Ujfalusi2013-10-231-1/+1
| | | | | | | | | | | When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM support got deprecated in favor of uEVM (or Panda5) the content was not validated. On uEVM the twl6040 reset GPIO is from gpio5_141 and not via gpio5_145, which was the case in sEVM. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: add smps123 supply for CPUNishanth Menon2013-10-221-0/+4
| | | | | | | | | regulator smps123 supply from Palmas PMIC powers CPU0 on OMAP5uEVM. Based on a patch by J Keerthy <j-keerthy@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: fix mcspi node pin descriptionsEric Witcher2013-10-221-9/+9
| | | | | | | | Correct mcspi pin descriptions to match corresponding node name and add chip select number to be consistent with OMAP5 TRM. Signed-off-by: Eric Witcher <ewitcher@mindspring.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: remove always_on, boot_on from smps10_out1Kishon Vijay Abraham I2013-10-201-2/+0
| | | | | | | | | | smps10 should be enabled only in the case of host mode. So stop doing always_on, boot_on from smps10_out1. The driver will enable it in host mode. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: mark TWL6037 as system-power-controllerNishanth Menon2013-10-111-0/+1
| | | | | | | | This allows the palmas pm_power_off to kick in on power off command and switch off the board. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: Use reset-gpios for hsusb2/3_resetRoger Quadros2013-10-111-24/+2
| | | | | | | | We no longer need to model the RESET line as a regulator since the USB phy-nop driver accepts "reset-gpios" property. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: OMAP5: add palmas-usb nodeFelipe Balbi2013-10-081-0/+12
| | | | | | | | | | | | Without this node, there will be no palmas driver to notify dwc3 that a cable has been connected and, without that, dwc3 will never initialize. Signed-off-by: Felipe Balbi <balbi@ti.com> [kishon@ti.com: added dt properties for enabling vbus/id interrupts and fixed vbus-supply value after SMPS10 is modeled as 2 regulators] Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: Split SMPS10 in two nodesKishon Vijay Abraham I2013-10-081-2/+11
| | | | | | | | SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as two regulators. The DT node is split to reflect it. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
* ARM: dts: omap5-uevm: update optional/unused regulator configurationsNishanth Menon2013-07-291-9/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, The regulator information is based on an older temporary pre-production board variant and does not reflect production board 750-2628-XXX boards. The following optional/unused regulators can be updated: - SMPS9 supplies TWL6040 over VDDA_2v1_AUD. This regulator needs to be enabled only when audio is active. Since it does not come active by default, it does not require "always-on" or "boot-on". - LDO2 and LDO8 do not go to any peripheral or connector on the board. Further, these unused regulators should have been 2.8V for LDO2 and 3.0V for LDO8. Mark these LDOs as disabled in the dts until needed. Reported-by: Marc Jüttner <m-juettner@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: J Keerthy <j-keerthy@ti.com> Acked-by: Benoit Cousson <benoit.cousson@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoCNishanth Menon2013-07-291-20/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, The regulator information is based on an older temporary pre-production board variant and does not reflect production board 750-2628-XXX boards. The following fixes are hence mandatory to ensure right voltage is supplied to key OMAP5 SoC voltage rails: - LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This can only be supplied at 1.5V or 1.8V and we currently supply 2.8V. To prevent any potential device damage risk, use the specified 1.5V-1.8V supply. Remove 'always-on' and 'boot-on' settings here as it is a 'on need' supply to SoC IP and is not enabled by PMIC by default at boot. - LDO3 supplies Low Latency Interface(LLI) hardware module which is a special hardware to communicate with Modem. However since uEVM is not setup by default for this communication, this should be disabled by default. Further, vdda_lli is supposed to be 1.5V and not 3V. - LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi This can only be supplied at 1.5V or 1.8V and we currently supply 2.2V. To prevent any potential device damage risk, use the specified 1.5V-1.8V supply. Remove 'always-on' and 'boot-on' settings here as it is a 'on need' supply to SoC IP and is not enabled by PMIC by default at boot. - LDO6 supplies the board specified VDDS_1V2_WKUP supply going to ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply 1.2V instead of 1.5V. - LDO7 supplies VDD_VPP which is vpp1. This is currently configured for 1.5V which as per data manual "A pulse width of 1000 ns and an amplitude of 2V is required to program each eFuse bit. Otherwise, VPP1 must not be supplied". So, fix the voltage to 2V. and disable the supply since we have no plans of programming efuse bits - it can only be done once - in factory. Further it is not enabled by default by PMIC so, 'boot-on' must be removed, and the 'always-on' needs to be removed to achieve pulsing if efuse needs to be programmed. - LDO9 supplies the board specified vdds_sdcard supply going within SoC specification of 1.8V or 3.0V. Further the supply is controlled by switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled on need basis. Reported-by: Marc Jüttner <m-juettner@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: J Keerthy <j-keerthy@ti.com> Acked-by: Benoit Cousson <benoit.cousson@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: omap5-uevm: document regulator signals used on the actual boardNishanth Menon2013-07-291-0/+18
| | | | | | | | | | | | | | | | commit e00c27ef3b4c23e39d0a77b7c8e5be44c28001c7 (ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes) introduced regulator entries for OMAP5uEVM. However, currently we use the Palmas regulator names which is used for different purposes on uEVM. Document the same based on 750-2628-XXX boards - which is meant to be supported by this dts. Reported-by: Marc Jüttner <m-juettner@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Acked-by: J Keerthy <j-keerthy@ti.com> Acked-by: Benoit Cousson <benoit.cousson@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: dts: omap5-uevm: Provide USB Host PHY clock frequencyRoger Quadros2013-06-191-0/+7
| | | | | | | | | USB Host PHY clock on port 2 must be configured to 19.2MHz. Provide this information. Cc: Sricharan R <r.sricharan@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
* ARM: dts: OMAP5: Add Palmas MFD node and regulator nodesJ Keerthy2013-06-181-0/+167
| | | | | | | | | | | | | Add Palmas MFD node and the regulator nodes for OMAP5. The node definitions are based on: https://lkml.org/lkml/2013/6/6/25 Boot tested on omap5-uevm board. Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk> Signed-off-by: J Keerthy <j-keerthy@ti.com> Reviewed-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
* ARM: dts: omap5-uevm: Add uart pinctrl dataSourav Poddar2013-06-181-0/+41
| | | | | | | | | | | | | | Booting omap5 uevm results in the following error "did not get pins for uart error: -19" This happens because omap5 uevm dts file is not adapted to use uart through pinctrl framework. Populate uart pinctrl data to get rid of the error. Signed-off-by: Sourav Poddar <sourav.poddar@ti.com> [r.sricharan@ti.com: Replaced constants with preprocessor macros] Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
* ARM: dts: omap5-uevm: Add LED support for uEVM blue LEDDan Murphy2013-06-181-0/+16
| | | | | | | | | | | Add support for blue LED 1 off of GPIO 153. Make the LED a heartbeat LED Configure the MUX for GPIO output. Signed-off-by: Dan Murphy <dmurphy@ti.com> [r.sricharan@ti.com: Replaced constants with preprocessor macros] Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
* ARM: dts: omap5-uevm: Add USB Host supportRoger Quadros2013-06-181-0/+70
| | | | | | | | | | | | | Provide the RESET regulators for the USB PHYs, the USB Host port modes and the PHY devices. Also provide pin multiplexer information for the USB host pins. Signed-off-by: Roger Quadros <rogerq@ti.com> [r.sricharan@ti.com: Replaced constants with preprocessor macros] Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
* ARM: dts: omap5: Make uevm as the official board and deprecate sevm supportSricharan R2013-06-181-0/+184
The uevm is the only official board supported for the OMAP5 soc in mainline. The existent sevm platform will no more be supported. Hence cleaning up the board dts file to have only the data required for uevm. Renaming the board dts file and adding the following cleanups. * There are no devices connected on I2C 2,3,4 buses. So remove the pinmux data for the same. * OMAP5432 and DDR3 memory is used in the uevm. Temperature polling is not supported with DDR3 memories. Because of DDR3 phy limitation the voltage change across DVFS and all shadow registers for DVFS on DDR3 is not supported. Hence the emif kernel driver is not required, so removing the DDR3 device file and emif nodes for uevm. * Keypad is not supported on uevm. So remove the device node. Signed-off-by: Sricharan R <r.sricharan@ti.com> Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
OpenPOWER on IntegriCloud