summaryrefslogtreecommitdiffstats
Commit message (Expand)AuthorAgeFilesLines
* wil6210: use HW capabilities mask in resetVladimir Kondratiev2015-01-154-56/+36
* wil6210: detect HW capabilitiesVladimir Kondratiev2015-01-152-1/+51
* wil6210: rework debugfs for BACKVladimir Kondratiev2015-01-151-17/+54
* wil6210: fix Tx VRING for STA modeVladimir Kondratiev2015-01-151-5/+41
* wil6210: use bitmap API for "status"Vladimir Kondratiev2015-01-157-38/+40
* wil6210: Increase number of associated stationsVladimir Kondratiev2015-01-151-1/+1
* wil6210: consider SNAP header in MTU calculationsVladimir Kondratiev2015-01-152-1/+5
* wil6210: fix max. MPDU sizeVladimir Kondratiev2015-01-155-6/+16
* wil6210: delba for responderVladimir Kondratiev2015-01-153-3/+17
* wil6210: control AMSDU on Tx side of Block AckVladimir Kondratiev2015-01-154-4/+20
* wil6210: improve debugfs for VRINGVladimir Kondratiev2015-01-151-3/+6
* wil6210: fix disconnect 1 STA in APVladimir Kondratiev2015-01-151-9/+20
* wil6210: improve debugfs for reorder bufferVladimir Kondratiev2015-01-151-1/+2
* wil6210: allow to configure ADDBA requestVladimir Kondratiev2015-01-154-8/+15
* wil6210: simple ADDBA on originator (Tx) sideVladimir Kondratiev2015-01-155-0/+134
* wil6210: ADDBA/DELBA flowsVladimir Kondratiev2015-01-156-44/+376
* ath9k: Add QCA956x HW supportMiaoqing Pan2015-01-156-32/+76
* ath9k: Fix register definitions for QCA956xMiaoqing Pan2015-01-151-8/+11
* ath9k: Add initvals for QCA956xMiaoqing Pan2015-01-152-1/+1106
* ath9k: Add HW IDs for QCA956xMiaoqing Pan2015-01-154-0/+13
* Merge ath-next from ath.gitKalle Valo2015-01-0920-728/+6730
|\
| * ath10k: fix build error when hwmon is offKalle Valo2015-01-091-0/+5
| * ath10k: set phymode to 11b when NO_OFDM flag setPeter Oh2014-12-231-1/+4
| * ath10k: send (re)assoc peer command when NSS changedJanusz Dziedzic2014-12-231-2/+3
| * ath10k: fix low TX rates when IBSS and HTJanusz Dziedzic2014-12-231-0/+7
| * ath10k: add thermal sensor device supportRajkumar Manoharan2014-12-234-0/+100
| * ath10k: add wmi interface for pdev_get_temperatureRajkumar Manoharan2014-12-234-0/+67
| * ath10k: add thermal cooling device supportRajkumar Manoharan2014-12-235-0/+213
| * ath10k: add wmi support for pdev_set_quiet_modeRajkumar Manoharan2014-12-233-0/+51
| * ath10k: add 10.2.4 firmware supportRajkumar Manoharan2014-12-235-2/+312
| * ath10k: print ath10k wmi op versionKalle Valo2014-12-231-5/+2
| * ath10k: use wmi op version to check which iface combination to useKalle Valo2014-12-231-6/+15
| * ath10k: set max_num_vdevs based on wmi op versionKalle Valo2014-12-232-4/+4
| * ath10k: advertise p2p dev supportMichal Kazior2014-12-162-9/+9
| * ath10k: enable per-vif sta powersaveMichal Kazior2014-12-161-4/+8
| * ath10k: prevent invalid ps timeout configMichal Kazior2014-12-161-1/+10
| * ath10k: fix STA u-APSDMichal Kazior2014-12-162-10/+76
| * ath10k: improve 11b coexMichal Kazior2014-12-161-1/+12
| * ath10k: unregister and remove frag_threshold callbackPeter Oh2014-12-161-24/+0
| * ath10k: add new wmi interface of NF cal periodPeter Oh2014-12-085-0/+88
| * ath10k: add new pdev parameters for fw 10.2Peter Oh2014-12-081-0/+3
| * ath10k: implement wmi-tlv backendMichal Kazior2014-12-088-1/+3701
| * ath10k: make some wmi functions publicMichal Kazior2014-12-082-80/+117
| * ath10k: introduce wmi opsMichal Kazior2014-12-089-442/+1364
| * ath10k: implement intermediate event argsMichal Kazior2014-12-082-96/+348
| * ath10k: set max_num_pending_tx in ath10k_core_init_firmware_features()Kalle Valo2014-12-082-5/+2
| * ath10k: add ATH10K_FW_IE_WMI_OP_VERSIONKalle Valo2014-12-083-8/+65
| * ath10k: create ath10k_core_init_features()Kalle Valo2014-12-081-9/+16
| * ath10k: clean up error handling in ath10k_core_probe_fw()Kalle Valo2014-12-081-10/+14
| * ath10k: move uart pin config into hw_paramsMichal Kazior2014-12-082-1/+3
OpenPOWER on IntegriCloud