| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
| |
- Don't add dac load detection property to DVI-D
- Make sure i2c info is valid before adding DP aux chan bus
- Don't create scaling_mode_property twice
- fix typo that prevented coherent and load detection from working
- add coherent prop to DP (for dp->dvi adapters)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
| |
If we don't need the zone we need to free it.
Acked-By: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Sometimes we will use a crtc for integerated LVDS, which is different with
that assigned by BIOS. If we want to get flicker-free transitions,
then we could read out the current state for it and set our current state
accordingly.
But it is true that if we aren't reading current state out, we do need
to turn everything off before modesetting. Otherwise the clocks can get very
angry and we get things worse than a flicker at boot.
In fact we also do the similar thing in UMS mode. We will disable all the
possible outputs/crtcs for the first modesetting.
So we disable all the possible outputs/crtcs before entering the KMS mode.
Before we configure connector/encoder/crtc, the function of
drm_helper_disable_unused_function can disable all the possible outputs/crtcs.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Rafal Milecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| |\
| |
| |
| |
| |
| |
| |
| |
| | |
This merges the radeon KMS DisplayPort and hotplug detect support.
Tested on RV635 DP card with a Dell 2408 monitor.
Conflicts:
drivers/gpu/drm/drm_fb_helper.c
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This enabled interrupt driven hpd support for all
radeon chips. Assuming the hpd pin is wired up
correctly, the driver will generate uevents on
digital monitor connect and disconnect and retrain
DP monitors automatically.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This just adds the functionality, it's not hooked up
yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This just adds the functionality, it's not hooked up
yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This just adds the functionality, it's not hooked up
yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
This populates the connectors with HPD (Hot Plug Detect)
information. This will be used in subsequent patches
for automatic digital monitor connect/disconnect handling.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
only return connected if there is actually a
monitor connected.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| | |
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| | |
This moves the radeon DP link training call to happen when we
dpms on the encoder not when we set the mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| | |
This fix reorganises the initial DP link training slightly, and
actually makes DP work under kms here.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| | |
Not returning here caused us to get a display port version of 0 for everything
this caused power up to not get sent which ends up in a black screen.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| | |
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
This will be used laster when the encoder and transmitters
are set up.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
- keep the atom i2c id in the i2c rec
- fix gpio regs for GPIO and MDGPIO on pre-avivo chips
- track whether the i2c line is hw capable
- track whether the i2c line uses the multimedia i2c block
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| |
| | |
- dpcp -> dpcd
- fix up dig encoder routing
- aux transaction table takes delay in 10 usec units
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| | |
This is enough to retrieve EDID and DPCP.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |
| |
| |
| |
| |
| |
| |
| | |
FB read/write really doesn't need to access the actual VRAM, we
can just use a scratch area. This is required for using atom displayport
calls later.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | |\
| | |
| | |
| | |
| | | |
Conflicts:
drivers/gpu/drm/drm_fb_helper.c
|
| |\ \ \
| |/ /
| | |
| | | |
This merges all the radeon changes that weren't reliant on core-next.
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Don't remap vram to 0 on IGP chips.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Grab pll ref div from regs at driver init. r4xx seems very
picky about the dividers for the pll driving lvds.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
The DDX and radeonfb always set these regs to a sane value.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
These can end up with garbage otherwise.
fixes rh bug 537140
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Again we try to put VRAM at 0, and it didn't work on this chipset,
reports of corrupt RAM appeared on irc and bugzilla.
Fix the vram location according to what the BIOS setup, I'm not 100%
sure we don't need the same thing on rs690/rs780/rs880, we probably
should do it there just in case as its what the DDX does.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Set up rs600 gart like r600:
- set gart system aperture to vram
- inside gart system aperture is unmapped*
- outside gart system aperture is mapped*
*mapped refers to memory handled by page tables
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
Similiar to other quirks for RV515, this card has no second DVI port.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
also fix up rs690 mem width.
should fix fdo bug 25408
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
noticed by Matthijs Kooijman on fdo bug 22140
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
avivo chips
Copied from pre-avivo code.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Board is DVI+VGA, not DVI+DVI
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
R4xx cards don't have lvds pll dividers since they use atom.
should fix rh bug 541562
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | | |
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
Unit typo noticed by taiu on IRC
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
The locking & protection of radeon object was somewhat messy.
This patch completely rework it to now use ttm reserve as a
protection for the radeon object structure member. It also
shrink down the various radeon object structure by removing
field which were redondant with the ttm information. Last it
converts few simple functions to inline which should with
performances.
airlied: rebase on top of r600 and other changes.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
We really don't need to process every irq that comes in, we only
really want to do SW irq processing when we are actually waiting for
a fence to pass. I'm not 100% sure this is race free esp on non-MSI systems
so it needs some testing.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
This enables the use of interrupts on r6xx/r7xx hardware.
Interrupts are implemented via a ring buffer. The GPU adds
interrupts vectors to the ring and the host reads them off
in the interrupt handler. The interrupt controller requires
firmware like the CP. This firmware must be installed and
accessble to the firmware loader for interrupts to function.
MSIs don't seem to work on my RS780. They work fine on all
my discrete cards. I'm not sure about other RS780s or
RS880s. I've disabled MSIs on RS780 and RS880, but it would
probably be worth checking on some other systems.
v2 - fix some checkpatch.pl problems;
re-read the disp int status reg if we restart the ih;
v3 - remove the irq handler if r600_irq_init() fails;
remove spinlock in r600_ih_ring_fini();
move ih rb overflow check to r600_get_ih_wptr();
move irq ack to separate function;
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | | |
found while working on displayport.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Don't overwritte crtc_gen_cntl or crtc_gen_cntl2 or we may loose the
cursor. This especialy happen when changing video mode. Fix bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=529146
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Lets user select tv-standard. The property was there,
just not hooked up.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
| | | |
| | |
| | |
| | |
| | |
| | |
| | | |
If we find a GPU but we can't find its BIOS and it isn't posted,
then ignore it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
