1 files changed, 104 insertions, 39 deletions

diff --git a/sound/soc/codecs/wm8962.c b/sound/soc/codecs/wm8962.c
index e9710280e5e1..b1dc7d426438 100644
--- a/sound/soc/codecs/wm8962.c
+++ b/sound/soc/codecs/wm8962.c
@@ -51,6 +51,7 @@ static const char *wm8962_supply_names[WM8962_NUM_SUPPLIES] = {
 
 /* codec private data */
 struct wm8962_priv {
+	struct wm8962_pdata pdata;
 	struct regmap *regmap;
 	struct snd_soc_codec *codec;
 
@@ -1600,7 +1601,6 @@ static int wm8962_put_hp_sw(struct snd_kcontrol *kcontrol,
 			    struct snd_ctl_elem_value *ucontrol)
 {
 	struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol);
-	u16 *reg_cache = codec->reg_cache;
 	int ret;
 
 	/* Apply the update (if any) */
@@ -1609,16 +1609,19 @@ static int wm8962_put_hp_sw(struct snd_kcontrol *kcontrol,
 		return 0;
 
 	/* If the left PGA is enabled hit that VU bit... */
-	if (snd_soc_read(codec, WM8962_PWR_MGMT_2) & WM8962_HPOUTL_PGA_ENA)
-		return snd_soc_write(codec, WM8962_HPOUTL_VOLUME,
-				     reg_cache[WM8962_HPOUTL_VOLUME]);
+	ret = snd_soc_read(codec, WM8962_PWR_MGMT_2);
+	if (ret & WM8962_HPOUTL_PGA_ENA) {
+		snd_soc_write(codec, WM8962_HPOUTL_VOLUME,
+			      snd_soc_read(codec, WM8962_HPOUTL_VOLUME));
+		return 1;
+	}
 
 	/* ...otherwise the right.  The VU is stereo. */
-	if (snd_soc_read(codec, WM8962_PWR_MGMT_2) & WM8962_HPOUTR_PGA_ENA)
-		return snd_soc_write(codec, WM8962_HPOUTR_VOLUME,
-				     reg_cache[WM8962_HPOUTR_VOLUME]);
+	if (ret & WM8962_HPOUTR_PGA_ENA)
+		snd_soc_write(codec, WM8962_HPOUTR_VOLUME,
+			      snd_soc_read(codec, WM8962_HPOUTR_VOLUME));
 
-	return 0;
+	return 1;
 }
 
 /* The VU bits for the speakers are in a different register to the mute
@@ -2345,12 +2348,13 @@ static const struct snd_soc_dapm_route wm8962_spk_stereo_intercon[] = {
 
 static int wm8962_add_widgets(struct snd_soc_codec *codec)
 {
-	struct wm8962_pdata *pdata = dev_get_platdata(codec->dev);
+	struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec);
+	struct wm8962_pdata *pdata = &wm8962->pdata;
 	struct snd_soc_dapm_context *dapm = &codec->dapm;
 
 	snd_soc_add_codec_controls(codec, wm8962_snd_controls,
 			     ARRAY_SIZE(wm8962_snd_controls));
-	if (pdata && pdata->spk_mono)
+	if (pdata->spk_mono)
 		snd_soc_add_codec_controls(codec, wm8962_spk_mono_controls,
 				     ARRAY_SIZE(wm8962_spk_mono_controls));
 	else
@@ -2360,7 +2364,7 @@ static int wm8962_add_widgets(struct snd_soc_codec *codec)
 
 	snd_soc_dapm_new_controls(dapm, wm8962_dapm_widgets,
 				  ARRAY_SIZE(wm8962_dapm_widgets));
-	if (pdata && pdata->spk_mono)
+	if (pdata->spk_mono)
 		snd_soc_dapm_new_controls(dapm, wm8962_dapm_spk_mono_widgets,
 					  ARRAY_SIZE(wm8962_dapm_spk_mono_widgets));
 	else
@@ -2369,7 +2373,7 @@ static int wm8962_add_widgets(struct snd_soc_codec *codec)
 
 	snd_soc_dapm_add_routes(dapm, wm8962_intercon,
 				ARRAY_SIZE(wm8962_intercon));
-	if (pdata && pdata->spk_mono)
+	if (pdata->spk_mono)
 		snd_soc_dapm_add_routes(dapm, wm8962_spk_mono_intercon,
 					ARRAY_SIZE(wm8962_spk_mono_intercon));
 	else
@@ -3333,14 +3337,14 @@ static struct gpio_chip wm8962_template_chip = {
 static void wm8962_init_gpio(struct snd_soc_codec *codec)
 {
 	struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec);
-	struct wm8962_pdata *pdata = dev_get_platdata(codec->dev);
+	struct wm8962_pdata *pdata = &wm8962->pdata;
 	int ret;
 
 	wm8962->gpio_chip = wm8962_template_chip;
 	wm8962->gpio_chip.ngpio = WM8962_MAX_GPIO;
 	wm8962->gpio_chip.dev = codec->dev;
 
-	if (pdata && pdata->gpio_base)
+	if (pdata->gpio_base)
 		wm8962->gpio_chip.base = pdata->gpio_base;
 	else
 		wm8962->gpio_chip.base = -1;
@@ -3374,7 +3378,6 @@ static int wm8962_probe(struct snd_soc_codec *codec)
 	int ret;
 	struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec);
 	struct wm8962_pdata *pdata = dev_get_platdata(codec->dev);
-	u16 *reg_cache = codec->reg_cache;
 	int i, trigger, irq_pol;
 	bool dmicclk, dmicdat;
 
@@ -3421,30 +3424,29 @@ static int wm8962_probe(struct snd_soc_codec *codec)
 			    WM8962_OSC_ENA | WM8962_PLL2_ENA | WM8962_PLL3_ENA,
 			    0);
 
-	if (pdata) {
-		/* Apply static configuration for GPIOs */
-		for (i = 0; i < ARRAY_SIZE(pdata->gpio_init); i++)
-			if (pdata->gpio_init[i]) {
-				wm8962_set_gpio_mode(codec, i + 1);
-				snd_soc_write(codec, 0x200 + i,
-					      pdata->gpio_init[i] & 0xffff);
-			}
+	/* Apply static configuration for GPIOs */
+	for (i = 0; i < ARRAY_SIZE(pdata->gpio_init); i++)
+		if (pdata->gpio_init[i]) {
+			wm8962_set_gpio_mode(codec, i + 1);
+			snd_soc_write(codec, 0x200 + i,
+					pdata->gpio_init[i] & 0xffff);
+		}
 
-		/* Put the speakers into mono mode? */
-		if (pdata->spk_mono)
-			reg_cache[WM8962_CLASS_D_CONTROL_2]
-				|= WM8962_SPK_MONO;
 
-		/* Micbias setup, detection enable and detection
-		 * threasholds. */
-		if (pdata->mic_cfg)
-			snd_soc_update_bits(codec, WM8962_ADDITIONAL_CONTROL_4,
-					    WM8962_MICDET_ENA |
-					    WM8962_MICDET_THR_MASK |
-					    WM8962_MICSHORT_THR_MASK |
-					    WM8962_MICBIAS_LVL,
-					    pdata->mic_cfg);
-	}
+	/* Put the speakers into mono mode? */
+	if (pdata->spk_mono)
+		snd_soc_update_bits(codec, WM8962_CLASS_D_CONTROL_2,
+				WM8962_SPK_MONO_MASK, WM8962_SPK_MONO);
+
+	/* Micbias setup, detection enable and detection
+	 * threasholds. */
+	if (pdata->mic_cfg)
+		snd_soc_update_bits(codec, WM8962_ADDITIONAL_CONTROL_4,
+				    WM8962_MICDET_ENA |
+				    WM8962_MICDET_THR_MASK |
+				    WM8962_MICSHORT_THR_MASK |
+				    WM8962_MICBIAS_LVL,
+				    pdata->mic_cfg);
 
 	/* Latch volume update bits */
 	snd_soc_update_bits(codec, WM8962_LEFT_INPUT_VOLUME,
@@ -3506,7 +3508,7 @@ static int wm8962_probe(struct snd_soc_codec *codec)
 	wm8962_init_gpio(codec);
 
 	if (wm8962->irq) {
-		if (pdata && pdata->irq_active_low) {
+		if (pdata->irq_active_low) {
 			trigger = IRQF_TRIGGER_LOW;
 			irq_pol = WM8962_IRQ_POL;
 		} else {
@@ -3584,6 +3586,34 @@ static const struct regmap_config wm8962_regmap = {
 	.cache_type = REGCACHE_RBTREE,
 };
 
+static int wm8962_set_pdata_from_of(struct i2c_client *i2c,
+				    struct wm8962_pdata *pdata)
+{
+	const struct device_node *np = i2c->dev.of_node;
+	u32 val32;
+	int i;
+
+	if (of_property_read_bool(np, "spk-mono"))
+		pdata->spk_mono = true;
+
+	if (of_property_read_u32(np, "mic-cfg", &val32) >= 0)
+		pdata->mic_cfg = val32;
+
+	if (of_property_read_u32_array(np, "gpio-cfg", pdata->gpio_init,
+				       ARRAY_SIZE(pdata->gpio_init)) >= 0)
+		for (i = 0; i < ARRAY_SIZE(pdata->gpio_init); i++) {
+			/*
+			 * The range of GPIO register value is [0x0, 0xffff]
+			 * While the default value of each register is 0x0
+			 * Any other value will be regarded as default value
+			 */
+			if (pdata->gpio_init[i] > 0xffff)
+				pdata->gpio_init[i] = 0x0;
+		}
+
+	return 0;
+}
+
 static int wm8962_i2c_probe(struct i2c_client *i2c,
 			    const struct i2c_device_id *id)
 {
@@ -3603,6 +3633,15 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
 	init_completion(&wm8962->fll_lock);
 	wm8962->irq = i2c->irq;
 
+	/* If platform data was supplied, update the default data in priv */
+	if (pdata) {
+		memcpy(&wm8962->pdata, pdata, sizeof(struct wm8962_pdata));
+	} else if (i2c->dev.of_node) {
+		ret = wm8962_set_pdata_from_of(i2c, &wm8962->pdata);
+		if (ret != 0)
+			return ret;
+	}
+
 	for (i = 0; i < ARRAY_SIZE(wm8962->supplies); i++)
 		wm8962->supplies[i].supply = wm8962_supply_names[i];
 
@@ -3666,7 +3705,7 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
 		goto err_enable;
 	}
 
-	if (pdata && pdata->in4_dc_measure) {
+	if (wm8962->pdata.in4_dc_measure) {
 		ret = regmap_register_patch(wm8962->regmap,
 					    wm8962_dc_measure,
 					    ARRAY_SIZE(wm8962_dc_measure));
@@ -3719,8 +3758,34 @@ static int wm8962_runtime_resume(struct device *dev)
 
 	wm8962_reset(wm8962);
 
+	/* SYSCLK defaults to on; make sure it is off so we can safely
+	 * write to registers if the device is declocked.
+	 */
+	regmap_update_bits(wm8962->regmap, WM8962_CLOCKING2,
+			   WM8962_SYSCLK_ENA, 0);
+
+	/* Ensure we have soft control over all registers */
+	regmap_update_bits(wm8962->regmap, WM8962_CLOCKING2,
+			   WM8962_CLKREG_OVD, WM8962_CLKREG_OVD);
+
+	/* Ensure that the oscillator and PLLs are disabled */
+	regmap_update_bits(wm8962->regmap, WM8962_PLL2,
+			   WM8962_OSC_ENA | WM8962_PLL2_ENA | WM8962_PLL3_ENA,
+			   0);
+
 	regcache_sync(wm8962->regmap);
 
+	regmap_update_bits(wm8962->regmap, WM8962_ANTI_POP,
+			   WM8962_STARTUP_BIAS_ENA | WM8962_VMID_BUF_ENA,
+			   WM8962_STARTUP_BIAS_ENA | WM8962_VMID_BUF_ENA);
+
+	/* Bias enable at 2*5k (fast start-up) */
+	regmap_update_bits(wm8962->regmap, WM8962_PWR_MGMT_1,
+			   WM8962_BIAS_ENA | WM8962_VMID_SEL_MASK,
+			   WM8962_BIAS_ENA | 0x180);
+
+	msleep(5);
+
 	return 0;
 }