summaryrefslogtreecommitdiffstats
path: root/drivers/tty/serial/max3107.h
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/tty/serial/max3107.h')
-rw-r--r--drivers/tty/serial/max3107.h441
1 files changed, 441 insertions, 0 deletions
diff --git a/drivers/tty/serial/max3107.h b/drivers/tty/serial/max3107.h
new file mode 100644
index 000000000000..7ab632392502
--- /dev/null
+++ b/drivers/tty/serial/max3107.h
@@ -0,0 +1,441 @@
+/*
+ * max3107.h - spi uart protocol driver header for Maxim 3107
+ *
+ * Copyright (C) Aavamobile 2009
+ * Based on serial_max3100.h by Christian Pellegrin
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef _MAX3107_H
+#define _MAX3107_H
+
+/* Serial error status definitions */
+#define MAX3107_PARITY_ERROR 1
+#define MAX3107_FRAME_ERROR 2
+#define MAX3107_OVERRUN_ERROR 4
+#define MAX3107_ALL_ERRORS (MAX3107_PARITY_ERROR | \
+ MAX3107_FRAME_ERROR | \
+ MAX3107_OVERRUN_ERROR)
+
+/* GPIO definitions */
+#define MAX3107_GPIO_BASE 88
+#define MAX3107_GPIO_COUNT 4
+
+
+/* GPIO connected to chip's reset pin */
+#define MAX3107_RESET_GPIO 87
+
+
+/* Chip reset delay */
+#define MAX3107_RESET_DELAY 10
+
+/* Chip wakeup delay */
+#define MAX3107_WAKEUP_DELAY 50
+
+
+/* Sleep mode definitions */
+#define MAX3107_DISABLE_FORCED_SLEEP 0
+#define MAX3107_ENABLE_FORCED_SLEEP 1
+#define MAX3107_DISABLE_AUTOSLEEP 2
+#define MAX3107_ENABLE_AUTOSLEEP 3
+
+
+/* Definitions for register access with SPI transfers
+ *
+ * SPI transfer format:
+ *
+ * Master to slave bits xzzzzzzzyyyyyyyy
+ * Slave to master bits aaaaaaaabbbbbbbb
+ *
+ * where:
+ * x = 0 for reads, 1 for writes
+ * z = register address
+ * y = new register value if write, 0 if read
+ * a = unspecified
+ * b = register value if read, unspecified if write
+ */
+
+/* SPI speed */
+#define MAX3107_SPI_SPEED (3125000 * 2)
+
+/* Write bit */
+#define MAX3107_WRITE_BIT (1 << 15)
+
+/* SPI TX data mask */
+#define MAX3107_SPI_RX_DATA_MASK (0x00ff)
+
+/* SPI RX data mask */
+#define MAX3107_SPI_TX_DATA_MASK (0x00ff)
+
+/* Register access masks */
+#define MAX3107_RHR_REG (0x0000) /* RX FIFO */
+#define MAX3107_THR_REG (0x0000) /* TX FIFO */
+#define MAX3107_IRQEN_REG (0x0100) /* IRQ enable */
+#define MAX3107_IRQSTS_REG (0x0200) /* IRQ status */
+#define MAX3107_LSR_IRQEN_REG (0x0300) /* LSR IRQ enable */
+#define MAX3107_LSR_IRQSTS_REG (0x0400) /* LSR IRQ status */
+#define MAX3107_SPCHR_IRQEN_REG (0x0500) /* Special char IRQ enable */
+#define MAX3107_SPCHR_IRQSTS_REG (0x0600) /* Special char IRQ status */
+#define MAX3107_STS_IRQEN_REG (0x0700) /* Status IRQ enable */
+#define MAX3107_STS_IRQSTS_REG (0x0800) /* Status IRQ status */
+#define MAX3107_MODE1_REG (0x0900) /* MODE1 */
+#define MAX3107_MODE2_REG (0x0a00) /* MODE2 */
+#define MAX3107_LCR_REG (0x0b00) /* LCR */
+#define MAX3107_RXTO_REG (0x0c00) /* RX timeout */
+#define MAX3107_HDPIXDELAY_REG (0x0d00) /* Auto transceiver delays */
+#define MAX3107_IRDA_REG (0x0e00) /* IRDA settings */
+#define MAX3107_FLOWLVL_REG (0x0f00) /* Flow control levels */
+#define MAX3107_FIFOTRIGLVL_REG (0x1000) /* FIFO IRQ trigger levels */
+#define MAX3107_TXFIFOLVL_REG (0x1100) /* TX FIFO level */
+#define MAX3107_RXFIFOLVL_REG (0x1200) /* RX FIFO level */
+#define MAX3107_FLOWCTRL_REG (0x1300) /* Flow control */
+#define MAX3107_XON1_REG (0x1400) /* XON1 character */
+#define MAX3107_XON2_REG (0x1500) /* XON2 character */
+#define MAX3107_XOFF1_REG (0x1600) /* XOFF1 character */
+#define MAX3107_XOFF2_REG (0x1700) /* XOFF2 character */
+#define MAX3107_GPIOCFG_REG (0x1800) /* GPIO config */
+#define MAX3107_GPIODATA_REG (0x1900) /* GPIO data */
+#define MAX3107_PLLCFG_REG (0x1a00) /* PLL config */
+#define MAX3107_BRGCFG_REG (0x1b00) /* Baud rate generator conf */
+#define MAX3107_BRGDIVLSB_REG (0x1c00) /* Baud rate divisor LSB */
+#define MAX3107_BRGDIVMSB_REG (0x1d00) /* Baud rate divisor MSB */
+#define MAX3107_CLKSRC_REG (0x1e00) /* Clock source */
+#define MAX3107_REVID_REG (0x1f00) /* Revision identification */
+
+/* IRQ register bits */
+#define MAX3107_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */
+#define MAX3107_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */
+#define MAX3107_IRQ_STS_BIT (1 << 2) /* Status interrupt */
+#define MAX3107_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */
+#define MAX3107_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */
+#define MAX3107_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */
+#define MAX3107_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */
+#define MAX3107_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */
+
+/* LSR register bits */
+#define MAX3107_LSR_RXTO_BIT (1 << 0) /* RX timeout */
+#define MAX3107_LSR_RXOVR_BIT (1 << 1) /* RX overrun */
+#define MAX3107_LSR_RXPAR_BIT (1 << 2) /* RX parity error */
+#define MAX3107_LSR_FRERR_BIT (1 << 3) /* Frame error */
+#define MAX3107_LSR_RXBRK_BIT (1 << 4) /* RX break */
+#define MAX3107_LSR_RXNOISE_BIT (1 << 5) /* RX noise */
+#define MAX3107_LSR_UNDEF6_BIT (1 << 6) /* Undefined/not used */
+#define MAX3107_LSR_CTS_BIT (1 << 7) /* CTS pin state */
+
+/* Special character register bits */
+#define MAX3107_SPCHR_XON1_BIT (1 << 0) /* XON1 character */
+#define MAX3107_SPCHR_XON2_BIT (1 << 1) /* XON2 character */
+#define MAX3107_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */
+#define MAX3107_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */
+#define MAX3107_SPCHR_BREAK_BIT (1 << 4) /* RX break */
+#define MAX3107_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */
+#define MAX3107_SPCHR_UNDEF6_BIT (1 << 6) /* Undefined/not used */
+#define MAX3107_SPCHR_UNDEF7_BIT (1 << 7) /* Undefined/not used */
+
+/* Status register bits */
+#define MAX3107_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */
+#define MAX3107_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */
+#define MAX3107_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */
+#define MAX3107_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */
+#define MAX3107_STS_UNDEF4_BIT (1 << 4) /* Undefined/not used */
+#define MAX3107_STS_CLKREADY_BIT (1 << 5) /* Clock ready */
+#define MAX3107_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */
+#define MAX3107_STS_UNDEF7_BIT (1 << 7) /* Undefined/not used */
+
+/* MODE1 register bits */
+#define MAX3107_MODE1_RXDIS_BIT (1 << 0) /* RX disable */
+#define MAX3107_MODE1_TXDIS_BIT (1 << 1) /* TX disable */
+#define MAX3107_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */
+#define MAX3107_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */
+#define MAX3107_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */
+#define MAX3107_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */
+#define MAX3107_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */
+#define MAX3107_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */
+
+/* MODE2 register bits */
+#define MAX3107_MODE2_RST_BIT (1 << 0) /* Chip reset */
+#define MAX3107_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */
+#define MAX3107_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */
+#define MAX3107_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */
+#define MAX3107_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */
+#define MAX3107_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */
+#define MAX3107_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */
+#define MAX3107_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */
+
+/* LCR register bits */
+#define MAX3107_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */
+#define MAX3107_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1
+ *
+ * Word length bits table:
+ * 00 -> 5 bit words
+ * 01 -> 6 bit words
+ * 10 -> 7 bit words
+ * 11 -> 8 bit words
+ */
+#define MAX3107_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit
+ *
+ * STOP length bit table:
+ * 0 -> 1 stop bit
+ * 1 -> 1-1.5 stop bits if
+ * word length is 5,
+ * 2 stop bits otherwise
+ */
+#define MAX3107_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */
+#define MAX3107_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */
+#define MAX3107_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */
+#define MAX3107_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */
+#define MAX3107_LCR_RTS_BIT (1 << 7) /* RTS pin control */
+#define MAX3107_LCR_WORD_LEN_5 (0x0000)
+#define MAX3107_LCR_WORD_LEN_6 (0x0001)
+#define MAX3107_LCR_WORD_LEN_7 (0x0002)
+#define MAX3107_LCR_WORD_LEN_8 (0x0003)
+
+
+/* IRDA register bits */
+#define MAX3107_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */
+#define MAX3107_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */
+#define MAX3107_IRDA_SHORTIR_BIT (1 << 2) /* Short SIR mode enable */
+#define MAX3107_IRDA_MIR_BIT (1 << 3) /* MIR mode enable */
+#define MAX3107_IRDA_RXINV_BIT (1 << 4) /* RX logic inversion enable */
+#define MAX3107_IRDA_TXINV_BIT (1 << 5) /* TX logic inversion enable */
+#define MAX3107_IRDA_UNDEF6_BIT (1 << 6) /* Undefined/not used */
+#define MAX3107_IRDA_UNDEF7_BIT (1 << 7) /* Undefined/not used */
+
+/* Flow control trigger level register masks */
+#define MAX3107_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */
+#define MAX3107_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */
+#define MAX3107_FLOWLVL_HALT(words) ((words/8) & 0x000f)
+#define MAX3107_FLOWLVL_RES(words) (((words/8) & 0x000f) << 4)
+
+/* FIFO interrupt trigger level register masks */
+#define MAX3107_FIFOTRIGLVL_TX_MASK (0x000f) /* TX FIFO trigger level */
+#define MAX3107_FIFOTRIGLVL_RX_MASK (0x00f0) /* RX FIFO trigger level */
+#define MAX3107_FIFOTRIGLVL_TX(words) ((words/8) & 0x000f)
+#define MAX3107_FIFOTRIGLVL_RX(words) (((words/8) & 0x000f) << 4)
+
+/* Flow control register bits */
+#define MAX3107_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */
+#define MAX3107_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */
+#define MAX3107_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs
+ * are used in conjunction with
+ * XOFF2 for definition of
+ * special character */
+#define MAX3107_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */
+#define MAX3107_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */
+#define MAX3107_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1
+ *
+ * SWFLOW bits 1 & 0 table:
+ * 00 -> no transmitter flow
+ * control
+ * 01 -> receiver compares
+ * XON2 and XOFF2
+ * and controls
+ * transmitter
+ * 10 -> receiver compares
+ * XON1 and XOFF1
+ * and controls
+ * transmitter
+ * 11 -> receiver compares
+ * XON1, XON2, XOFF1 and
+ * XOFF2 and controls
+ * transmitter
+ */
+#define MAX3107_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */
+#define MAX3107_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3
+ *
+ * SWFLOW bits 3 & 2 table:
+ * 00 -> no received flow
+ * control
+ * 01 -> transmitter generates
+ * XON2 and XOFF2
+ * 10 -> transmitter generates
+ * XON1 and XOFF1
+ * 11 -> transmitter generates
+ * XON1, XON2, XOFF1 and
+ * XOFF2
+ */
+
+/* GPIO configuration register bits */
+#define MAX3107_GPIOCFG_GP0OUT_BIT (1 << 0) /* GPIO 0 output enable */
+#define MAX3107_GPIOCFG_GP1OUT_BIT (1 << 1) /* GPIO 1 output enable */
+#define MAX3107_GPIOCFG_GP2OUT_BIT (1 << 2) /* GPIO 2 output enable */
+#define MAX3107_GPIOCFG_GP3OUT_BIT (1 << 3) /* GPIO 3 output enable */
+#define MAX3107_GPIOCFG_GP0OD_BIT (1 << 4) /* GPIO 0 open-drain enable */
+#define MAX3107_GPIOCFG_GP1OD_BIT (1 << 5) /* GPIO 1 open-drain enable */
+#define MAX3107_GPIOCFG_GP2OD_BIT (1 << 6) /* GPIO 2 open-drain enable */
+#define MAX3107_GPIOCFG_GP3OD_BIT (1 << 7) /* GPIO 3 open-drain enable */
+
+/* GPIO DATA register bits */
+#define MAX3107_GPIODATA_GP0OUT_BIT (1 << 0) /* GPIO 0 output value */
+#define MAX3107_GPIODATA_GP1OUT_BIT (1 << 1) /* GPIO 1 output value */
+#define MAX3107_GPIODATA_GP2OUT_BIT (1 << 2) /* GPIO 2 output value */
+#define MAX3107_GPIODATA_GP3OUT_BIT (1 << 3) /* GPIO 3 output value */
+#define MAX3107_GPIODATA_GP0IN_BIT (1 << 4) /* GPIO 0 input value */
+#define MAX3107_GPIODATA_GP1IN_BIT (1 << 5) /* GPIO 1 input value */
+#define MAX3107_GPIODATA_GP2IN_BIT (1 << 6) /* GPIO 2 input value */
+#define MAX3107_GPIODATA_GP3IN_BIT (1 << 7) /* GPIO 3 input value */
+
+/* PLL configuration register masks */
+#define MAX3107_PLLCFG_PREDIV_MASK (0x003f) /* PLL predivision value */
+#define MAX3107_PLLCFG_PLLFACTOR_MASK (0x00c0) /* PLL multiplication factor */
+
+/* Baud rate generator configuration register masks and bits */
+#define MAX3107_BRGCFG_FRACT_MASK (0x000f) /* Fractional portion of
+ * Baud rate generator divisor
+ */
+#define MAX3107_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */
+#define MAX3107_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */
+#define MAX3107_BRGCFG_UNDEF6_BIT (1 << 6) /* Undefined/not used */
+#define MAX3107_BRGCFG_UNDEF7_BIT (1 << 7) /* Undefined/not used */
+
+/* Clock source register bits */
+#define MAX3107_CLKSRC_INTOSC_BIT (1 << 0) /* Internal osc enable */
+#define MAX3107_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */
+#define MAX3107_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */
+#define MAX3107_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */
+#define MAX3107_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */
+#define MAX3107_CLKSRC_UNDEF5_BIT (1 << 5) /* Undefined/not used */
+#define MAX3107_CLKSRC_UNDEF6_BIT (1 << 6) /* Undefined/not used */
+#define MAX3107_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */
+
+
+/* HW definitions */
+#define MAX3107_RX_FIFO_SIZE 128
+#define MAX3107_TX_FIFO_SIZE 128
+#define MAX3107_REVID1 0x00a0
+#define MAX3107_REVID2 0x00a1
+
+
+/* Baud rate generator configuration values for external clock 13MHz */
+#define MAX3107_BRG13_B300 (0x0A9400 | 0x05)
+#define MAX3107_BRG13_B600 (0x054A00 | 0x03)
+#define MAX3107_BRG13_B1200 (0x02A500 | 0x01)
+#define MAX3107_BRG13_B2400 (0x015200 | 0x09)
+#define MAX3107_BRG13_B4800 (0x00A900 | 0x04)
+#define MAX3107_BRG13_B9600 (0x005400 | 0x0A)
+#define MAX3107_BRG13_B19200 (0x002A00 | 0x05)
+#define MAX3107_BRG13_B38400 (0x001500 | 0x03)
+#define MAX3107_BRG13_B57600 (0x000E00 | 0x02)
+#define MAX3107_BRG13_B115200 (0x000700 | 0x01)
+#define MAX3107_BRG13_B230400 (0x000300 | 0x08)
+#define MAX3107_BRG13_B460800 (0x000100 | 0x0c)
+#define MAX3107_BRG13_B921600 (0x000100 | 0x1c)
+
+/* Baud rate generator configuration values for external clock 26MHz */
+#define MAX3107_BRG26_B300 (0x152800 | 0x0A)
+#define MAX3107_BRG26_B600 (0x0A9400 | 0x05)
+#define MAX3107_BRG26_B1200 (0x054A00 | 0x03)
+#define MAX3107_BRG26_B2400 (0x02A500 | 0x01)
+#define MAX3107_BRG26_B4800 (0x015200 | 0x09)
+#define MAX3107_BRG26_B9600 (0x00A900 | 0x04)
+#define MAX3107_BRG26_B19200 (0x005400 | 0x0A)
+#define MAX3107_BRG26_B38400 (0x002A00 | 0x05)
+#define MAX3107_BRG26_B57600 (0x001C00 | 0x03)
+#define MAX3107_BRG26_B115200 (0x000E00 | 0x02)
+#define MAX3107_BRG26_B230400 (0x000700 | 0x01)
+#define MAX3107_BRG26_B460800 (0x000300 | 0x08)
+#define MAX3107_BRG26_B921600 (0x000100 | 0x0C)
+
+/* Baud rate generator configuration values for internal clock */
+#define MAX3107_BRG13_IB300 (0x008000 | 0x00)
+#define MAX3107_BRG13_IB600 (0x004000 | 0x00)
+#define MAX3107_BRG13_IB1200 (0x002000 | 0x00)
+#define MAX3107_BRG13_IB2400 (0x001000 | 0x00)
+#define MAX3107_BRG13_IB4800 (0x000800 | 0x00)
+#define MAX3107_BRG13_IB9600 (0x000400 | 0x00)
+#define MAX3107_BRG13_IB19200 (0x000200 | 0x00)
+#define MAX3107_BRG13_IB38400 (0x000100 | 0x00)
+#define MAX3107_BRG13_IB57600 (0x000000 | 0x0B)
+#define MAX3107_BRG13_IB115200 (0x000000 | 0x05)
+#define MAX3107_BRG13_IB230400 (0x000000 | 0x03)
+#define MAX3107_BRG13_IB460800 (0x000000 | 0x00)
+#define MAX3107_BRG13_IB921600 (0x000000 | 0x00)
+
+
+struct baud_table {
+ int baud;
+ u32 new_brg;
+};
+
+struct max3107_port {
+ /* UART port structure */
+ struct uart_port port;
+
+ /* SPI device structure */
+ struct spi_device *spi;
+
+#if defined(CONFIG_GPIOLIB)
+ /* GPIO chip stucture */
+ struct gpio_chip chip;
+#endif
+
+ /* Workqueue that does all the magic */
+ struct workqueue_struct *workqueue;
+ struct work_struct work;
+
+ /* Lock for shared data */
+ spinlock_t data_lock;
+
+ /* Device configuration */
+ int ext_clk; /* 1 if external clock used */
+ int loopback; /* Current loopback mode state */
+ int baud; /* Current baud rate */
+
+ /* State flags */
+ int suspended; /* Indicates suspend mode */
+ int tx_fifo_empty; /* Flag for TX FIFO state */
+ int rx_enabled; /* Flag for receiver state */
+ int tx_enabled; /* Flag for transmitter state */
+
+ u16 irqen_reg; /* Current IRQ enable register value */
+ /* Shared data */
+ u16 mode1_reg; /* Current mode1 register value*/
+ int mode1_commit; /* Flag for setting new mode1 register value */
+ u16 lcr_reg; /* Current LCR register value */
+ int lcr_commit; /* Flag for setting new LCR register value */
+ u32 brg_cfg; /* Current Baud rate generator config */
+ int brg_commit; /* Flag for setting new baud rate generator
+ * config
+ */
+ struct baud_table *baud_tbl;
+ int handle_irq; /* Indicates that IRQ should be handled */
+
+ /* Rx buffer and str*/
+ u16 *rxbuf;
+ u8 *rxstr;
+ /* Tx buffer*/
+ u16 *txbuf;
+
+ struct max3107_plat *pdata; /* Platform data */
+};
+
+/* Platform data structure */
+struct max3107_plat {
+ /* Loopback mode enable */
+ int loopback;
+ /* External clock enable */
+ int ext_clk;
+ /* Called during the register initialisation */
+ void (*init)(struct max3107_port *s);
+ /* Called when the port is found and configured */
+ int (*configure)(struct max3107_port *s);
+ /* HW suspend function */
+ void (*hw_suspend) (struct max3107_port *s, int suspend);
+ /* Polling mode enable */
+ int polled_mode;
+ /* Polling period if polling mode enabled */
+ int poll_time;
+};
+
+extern int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len);
+extern void max3107_hw_susp(struct max3107_port *s, int suspend);
+extern int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata);
+extern int max3107_remove(struct spi_device *spi);
+extern int max3107_suspend(struct spi_device *spi, pm_message_t state);
+extern int max3107_resume(struct spi_device *spi);
+
+#endif /* _LINUX_SERIAL_MAX3107_H */
OpenPOWER on IntegriCloud