diff options
Diffstat (limited to 'drivers/tty/serial/amba-pl011.c')
| -rw-r--r-- | drivers/tty/serial/amba-pl011.c | 171 |
1 files changed, 171 insertions, 0 deletions
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 6558400f766f..c0850f3cc439 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -101,6 +101,14 @@ static struct vendor_data vendor_arm = { .get_fifosize = get_fifosize_arm, }; +static struct vendor_data vendor_sbsa = { + .oversampling = false, + .dma_threshold = false, + .cts_event_workaround = false, + .always_enabled = true, + .fixed_options = true, +}; + static unsigned int get_fifosize_st(struct amba_device *dev) { return 64; @@ -1641,6 +1649,28 @@ static int pl011_startup(struct uart_port *port) return retval; } +static int sbsa_uart_startup(struct uart_port *port) +{ + struct uart_amba_port *uap = + container_of(port, struct uart_amba_port, port); + int retval; + + retval = pl011_hwinit(port); + if (retval) + return retval; + + retval = pl011_allocate_irq(uap); + if (retval) + return retval; + + /* The SBSA UART does not support any modem status lines. */ + uap->old_status = 0; + + pl011_enable_interrupts(uap); + + return 0; +} + static void pl011_shutdown_channel(struct uart_amba_port *uap, unsigned int lcrh) { @@ -1721,6 +1751,19 @@ static void pl011_shutdown(struct uart_port *port) uap->port.ops->flush_buffer(port); } +static void sbsa_uart_shutdown(struct uart_port *port) +{ + struct uart_amba_port *uap = + container_of(port, struct uart_amba_port, port); + + pl011_disable_interrupts(uap); + + free_irq(uap->port.irq, uap); + + if (uap->port.ops->flush_buffer) + uap->port.ops->flush_buffer(port); +} + static void pl011_setup_status_masks(struct uart_port *port, struct ktermios *termios) { @@ -1872,6 +1915,27 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios, spin_unlock_irqrestore(&port->lock, flags); } +static void +sbsa_uart_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + struct uart_amba_port *uap = + container_of(port, struct uart_amba_port, port); + unsigned long flags; + + tty_termios_encode_baud_rate(termios, uap->fixed_baud, uap->fixed_baud); + + /* The SBSA UART only supports 8n1 without hardware flow control. */ + termios->c_cflag &= ~(CSIZE | CSTOPB | PARENB | PARODD); + termios->c_cflag &= ~(CMSPAR | CRTSCTS); + termios->c_cflag |= CS8 | CLOCAL; + + spin_lock_irqsave(&port->lock, flags); + uart_update_timeout(port, CS8, uap->fixed_baud); + pl011_setup_status_masks(port, termios); + spin_unlock_irqrestore(&port->lock, flags); +} + static const char *pl011_type(struct uart_port *port) { struct uart_amba_port *uap = @@ -1947,6 +2011,37 @@ static struct uart_ops amba_pl011_pops = { #endif }; +static void sbsa_uart_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ +} + +static unsigned int sbsa_uart_get_mctrl(struct uart_port *port) +{ + return 0; +} + +static const struct uart_ops sbsa_uart_pops = { + .tx_empty = pl011_tx_empty, + .set_mctrl = sbsa_uart_set_mctrl, + .get_mctrl = sbsa_uart_get_mctrl, + .stop_tx = pl011_stop_tx, + .start_tx = pl011_start_tx, + .stop_rx = pl011_stop_rx, + .startup = sbsa_uart_startup, + .shutdown = sbsa_uart_shutdown, + .set_termios = sbsa_uart_set_termios, + .type = pl011_type, + .release_port = pl011_release_port, + .request_port = pl011_request_port, + .config_port = pl011_config_port, + .verify_port = pl011_verify_port, +#ifdef CONFIG_CONSOLE_POLL + .poll_init = pl011_hwinit, + .poll_get_char = pl011_get_poll_char, + .poll_put_char = pl011_put_poll_char, +#endif +}; + static struct uart_amba_port *amba_ports[UART_NR]; #ifdef CONFIG_SERIAL_AMBA_PL011_CONSOLE @@ -2327,6 +2422,79 @@ static int pl011_resume(struct device *dev) static SIMPLE_DEV_PM_OPS(pl011_dev_pm_ops, pl011_suspend, pl011_resume); +static int sbsa_uart_probe(struct platform_device *pdev) +{ + struct uart_amba_port *uap; + struct resource *r; + int portnr, ret; + int baudrate; + + /* + * Check the mandatory baud rate parameter in the DT node early + * so that we can easily exit with the error. + */ + if (pdev->dev.of_node) { + struct device_node *np = pdev->dev.of_node; + + ret = of_property_read_u32(np, "current-speed", &baudrate); + if (ret) + return ret; + } else { + baudrate = 115200; + } + + portnr = pl011_find_free_port(); + if (portnr < 0) + return portnr; + + uap = devm_kzalloc(&pdev->dev, sizeof(struct uart_amba_port), + GFP_KERNEL); + if (!uap) + return -ENOMEM; + + uap->vendor = &vendor_sbsa; + uap->fifosize = 32; + uap->port.irq = platform_get_irq(pdev, 0); + uap->port.ops = &sbsa_uart_pops; + uap->fixed_baud = baudrate; + + snprintf(uap->type, sizeof(uap->type), "SBSA"); + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + + ret = pl011_setup_port(&pdev->dev, uap, r, portnr); + if (ret) + return ret; + + platform_set_drvdata(pdev, uap); + + return pl011_register_port(uap); +} + +static int sbsa_uart_remove(struct platform_device *pdev) +{ + struct uart_amba_port *uap = platform_get_drvdata(pdev); + + uart_remove_one_port(&amba_reg, &uap->port); + pl011_unregister_port(uap); + return 0; +} + +static const struct of_device_id sbsa_uart_of_match[] = { + { .compatible = "arm,sbsa-uart", }, + {}, +}; +MODULE_DEVICE_TABLE(of, sbsa_uart_of_match); + +static struct platform_driver arm_sbsa_uart_platform_driver = { + .probe = sbsa_uart_probe, + .remove = sbsa_uart_remove, + .driver = { + .name = "sbsa-uart", + .of_match_table = of_match_ptr(sbsa_uart_of_match), + }, +}; + static struct amba_id pl011_ids[] = { { .id = 0x00041011, @@ -2357,11 +2525,14 @@ static int __init pl011_init(void) { printk(KERN_INFO "Serial: AMBA PL011 UART driver\n"); + if (platform_driver_register(&arm_sbsa_uart_platform_driver)) + pr_warn("could not register SBSA UART platform driver\n"); return amba_driver_register(&pl011_driver); } static void __exit pl011_exit(void) { + platform_driver_unregister(&arm_sbsa_uart_platform_driver); amba_driver_unregister(&pl011_driver); } |
