9 files changed, 181 insertions, 149 deletions

diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index 34eb676916fe..1ebf8538b4fa 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -117,13 +117,6 @@ static inline void serial_dl_write(struct uart_8250_port *up, int value)
  * is cleared, the machine locks up with endless interrupts.
  */
 #define ALPHA_KLUDGE_MCR  (UART_MCR_OUT2 | UART_MCR_OUT1)
-#elif defined(CONFIG_SBC8560)
-/*
- * WindRiver did something similarly broken on their SBC8560 board. The
- * UART tristates its IRQ output while OUT2 is clear, but they pulled
- * the interrupt line _up_ instead of down, so if we register the IRQ
- * while the UART is in that state, we die in an IRQ storm. */
-#define ALPHA_KLUDGE_MCR (UART_MCR_OUT2)
 #else
 #define ALPHA_KLUDGE_MCR 0
 #endif
diff --git a/drivers/tty/serial/8250/8250.c b/drivers/tty/serial/8250/8250_core.c
index cf6a5383748a..86c00b1c5583 100644
--- a/drivers/tty/serial/8250/8250.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -3247,6 +3247,10 @@ int serial8250_register_8250_port(struct uart_8250_port *up)
 		uart->tx_loadsz		= up->tx_loadsz;
 		uart->capabilities	= up->capabilities;
 
+		/* Take tx_loadsz from fifosize if it wasn't set separately */
+		if (uart->port.fifosize && !uart->tx_loadsz)
+			uart->tx_loadsz = uart->port.fifosize;
+
 		if (up->port.dev)
 			uart->port.dev = up->port.dev;
 
@@ -3418,6 +3422,7 @@ MODULE_PARM_DESC(probe_rsa, "Probe I/O ports for RSA");
 #endif
 MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR);
 
+#ifdef CONFIG_SERIAL_8250_DEPRECATED_OPTIONS
 #ifndef MODULE
 /* This module was renamed to 8250_core in 3.7.  Keep the old "8250" name
  * working as well for the module options so we don't break people.  We
@@ -3432,7 +3437,7 @@ MODULE_ALIAS_CHARDEV_MAJOR(TTY_MAJOR);
 static void __used s8250_options(void)
 {
 #undef MODULE_PARAM_PREFIX
-#define MODULE_PARAM_PREFIX "8250."
+#define MODULE_PARAM_PREFIX "8250_core."
 
 	module_param_cb(share_irqs, &param_ops_uint, &share_irqs, 0644);
 	module_param_cb(nr_uarts, &param_ops_uint, &nr_uarts, 0644);
@@ -3444,5 +3449,6 @@ static void __used s8250_options(void)
 #endif
 }
 #else
-MODULE_ALIAS("8250");
+MODULE_ALIAS("8250_core");
+#endif
 #endif
diff --git a/drivers/tty/serial/8250/8250_dma.c b/drivers/tty/serial/8250/8250_dma.c
index b9f7fd28112e..7046769608d4 100644
--- a/drivers/tty/serial/8250/8250_dma.c
+++ b/drivers/tty/serial/8250/8250_dma.c
@@ -33,10 +33,8 @@ static void __dma_tx_complete(void *param)
 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
 		uart_write_wakeup(&p->port);
 
-	if (!uart_circ_empty(xmit) && !uart_tx_stopped(&p->port)) {
+	if (!uart_circ_empty(xmit) && !uart_tx_stopped(&p->port))
 		serial8250_tx_dma(p);
-		uart_write_wakeup(&p->port);
-	}
 }
 
 static void __dma_rx_complete(void *param)
@@ -67,12 +65,11 @@ int serial8250_tx_dma(struct uart_8250_port *p)
 	struct circ_buf			*xmit = &p->port.state->xmit;
 	struct dma_async_tx_descriptor	*desc;
 
-	if (dma->tx_running)
-		return -EBUSY;
+	if (uart_tx_stopped(&p->port) || dma->tx_running ||
+	    uart_circ_empty(xmit))
+		return 0;
 
 	dma->tx_size = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE);
-	if (!dma->tx_size)
-		return -EINVAL;
 
 	desc = dmaengine_prep_slave_single(dma->txchan,
 					   dma->tx_addr + xmit->tail,
@@ -104,20 +101,29 @@ int serial8250_rx_dma(struct uart_8250_port *p, unsigned int iir)
 	struct dma_tx_state		state;
 	int				dma_status;
 
-	/*
-	 * If RCVR FIFO trigger level was not reached, complete the transfer and
-	 * let 8250.c copy the remaining data.
-	 */
-	if ((iir & 0x3f) == UART_IIR_RX_TIMEOUT) {
-		dma_status = dmaengine_tx_status(dma->rxchan, dma->rx_cookie,
-						&state);
+	dma_status = dmaengine_tx_status(dma->rxchan, dma->rx_cookie, &state);
+
+	switch (iir & 0x3f) {
+	case UART_IIR_RLSI:
+		/* 8250_core handles errors and break interrupts */
+		return -EIO;
+	case UART_IIR_RX_TIMEOUT:
+		/*
+		 * If RCVR FIFO trigger level was not reached, complete the
+		 * transfer and let 8250_core copy the remaining data.
+		 */
 		if (dma_status == DMA_IN_PROGRESS) {
 			dmaengine_pause(dma->rxchan);
 			__dma_rx_complete(p);
 		}
 		return -ETIMEDOUT;
+	default:
+		break;
 	}
 
+	if (dma_status)
+		return 0;
+
 	desc = dmaengine_prep_slave_single(dma->rxchan, dma->rx_addr,
 					   dma->rx_size, DMA_DEV_TO_MEM,
 					   DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
@@ -143,21 +149,31 @@ int serial8250_request_dma(struct uart_8250_port *p)
 	struct uart_8250_dma	*dma = p->dma;
 	dma_cap_mask_t		mask;
 
-	dma->rxconf.src_addr = p->port.mapbase + UART_RX;
-	dma->txconf.dst_addr = p->port.mapbase + UART_TX;
+	/* Default slave configuration parameters */
+	dma->rxconf.direction		= DMA_DEV_TO_MEM;
+	dma->rxconf.src_addr_width	= DMA_SLAVE_BUSWIDTH_1_BYTE;
+	dma->rxconf.src_addr		= p->port.mapbase + UART_RX;
+
+	dma->txconf.direction		= DMA_MEM_TO_DEV;
+	dma->txconf.dst_addr_width	= DMA_SLAVE_BUSWIDTH_1_BYTE;
+	dma->txconf.dst_addr		= p->port.mapbase + UART_TX;
 
 	dma_cap_zero(mask);
 	dma_cap_set(DMA_SLAVE, mask);
 
 	/* Get a channel for RX */
-	dma->rxchan = dma_request_channel(mask, dma->fn, dma->rx_param);
+	dma->rxchan = dma_request_slave_channel_compat(mask,
+						       dma->fn, dma->rx_param,
+						       p->port.dev, "rx");
 	if (!dma->rxchan)
 		return -ENODEV;
 
 	dmaengine_slave_config(dma->rxchan, &dma->rxconf);
 
 	/* Get a channel for TX */
-	dma->txchan = dma_request_channel(mask, dma->fn, dma->tx_param);
+	dma->txchan = dma_request_slave_channel_compat(mask,
+						       dma->fn, dma->tx_param,
+						       p->port.dev, "tx");
 	if (!dma->txchan) {
 		dma_release_channel(dma->rxchan);
 		return -ENODEV;
diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index db0e66f6dd0e..d07b6af3a937 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -26,6 +26,8 @@
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/acpi.h>
+#include <linux/clk.h>
+#include <linux/pm_runtime.h>
 
 #include "8250.h"
 
@@ -34,9 +36,6 @@
 #define DW_UART_CPR	0xf4 /* Component Parameter Register */
 #define DW_UART_UCV	0xf8 /* UART Component Version */
 
-/* Intel Low Power Subsystem specific */
-#define LPSS_PRV_CLOCK_PARAMS 0x800
-
 /* Component Parameter Register bits */
 #define DW_UART_CPR_ABP_DATA_WIDTH	(3 << 0)
 #define DW_UART_CPR_AFCE_MODE		(1 << 4)
@@ -55,8 +54,9 @@
 
 
 struct dw8250_data {
-	int	last_lcr;
-	int	line;
+	int		last_lcr;
+	int		line;
+	struct clk	*clk;
 };
 
 static void dw8250_serial_out(struct uart_port *p, int offset, int value)
@@ -113,6 +113,18 @@ static int dw8250_handle_irq(struct uart_port *p)
 	return 0;
 }
 
+static void
+dw8250_do_pm(struct uart_port *port, unsigned int state, unsigned int old)
+{
+	if (!state)
+		pm_runtime_get_sync(port->dev);
+
+	serial8250_do_pm(port, state, old);
+
+	if (state)
+		pm_runtime_put_sync_suspend(port->dev);
+}
+
 static int dw8250_probe_of(struct uart_port *p)
 {
 	struct device_node	*np = p->dev->of_node;
@@ -136,8 +148,13 @@ static int dw8250_probe_of(struct uart_port *p)
 	if (!of_property_read_u32(np, "reg-shift", &val))
 		p->regshift = val;
 
+	/* clock got configured through clk api, all done */
+	if (p->uartclk)
+		return 0;
+
+	/* try to find out clock frequency from DT as fallback */
 	if (of_property_read_u32(np, "clock-frequency", &val)) {
-		dev_err(p->dev, "no clock-frequency property set\n");
+		dev_err(p->dev, "clk or clock-frequency not defined\n");
 		return -EINVAL;
 	}
 	p->uartclk = val;
@@ -146,67 +163,10 @@ static int dw8250_probe_of(struct uart_port *p)
 }
 
 #ifdef CONFIG_ACPI
-static bool dw8250_acpi_dma_filter(struct dma_chan *chan, void *parm)
-{
-	return chan->chan_id == *(int *)parm;
-}
-
-static acpi_status
-dw8250_acpi_walk_resource(struct acpi_resource *res, void *data)
-{
-	struct uart_port		*p = data;
-	struct uart_8250_port		*port;
-	struct uart_8250_dma		*dma;
-	struct acpi_resource_fixed_dma	*fixed_dma;
-	struct dma_slave_config		*slave;
-
-	port = container_of(p, struct uart_8250_port, port);
-
-	switch (res->type) {
-	case ACPI_RESOURCE_TYPE_FIXED_DMA:
-		fixed_dma = &res->data.fixed_dma;
-
-		/* TX comes first */
-		if (!port->dma) {
-			dma = devm_kzalloc(p->dev, sizeof(*dma), GFP_KERNEL);
-			if (!dma)
-				return AE_NO_MEMORY;
-
-			port->dma = dma;
-			slave = &dma->txconf;
-
-			slave->direction	= DMA_MEM_TO_DEV;
-			slave->dst_addr_width	= DMA_SLAVE_BUSWIDTH_1_BYTE;
-			slave->slave_id		= fixed_dma->request_lines;
-			slave->dst_maxburst	= port->tx_loadsz / 4;
-
-			dma->tx_chan_id		= fixed_dma->channels;
-			dma->tx_param		= &dma->tx_chan_id;
-			dma->fn			= dw8250_acpi_dma_filter;
-		} else {
-			dma = port->dma;
-			slave = &dma->rxconf;
-
-			slave->direction	= DMA_DEV_TO_MEM;
-			slave->src_addr_width	= DMA_SLAVE_BUSWIDTH_1_BYTE;
-			slave->slave_id		= fixed_dma->request_lines;
-			slave->src_maxburst	= p->fifosize / 4;
-
-			dma->rx_chan_id		= fixed_dma->channels;
-			dma->rx_param		= &dma->rx_chan_id;
-		}
-
-		break;
-	}
-
-	return AE_OK;
-}
-
-static int dw8250_probe_acpi(struct uart_port *p)
+static int dw8250_probe_acpi(struct uart_8250_port *up)
 {
 	const struct acpi_device_id *id;
-	acpi_status status;
-	u32 reg;
+	struct uart_port *p = &up->port;
 
 	id = acpi_match_device(p->dev->driver->acpi_match_table, p->dev);
 	if (!id)
@@ -216,26 +176,21 @@ static int dw8250_probe_acpi(struct uart_port *p)
 	p->serial_in = dw8250_serial_in32;
 	p->serial_out = dw8250_serial_out32;
 	p->regshift = 2;
-	p->uartclk = (unsigned int)id->driver_data;
 
-	status = acpi_walk_resources(ACPI_HANDLE(p->dev), METHOD_NAME__CRS,
-				     dw8250_acpi_walk_resource, p);
-	if (ACPI_FAILURE(status)) {
-		dev_err_ratelimited(p->dev, "%s failed \"%s\"\n", __func__,
-				    acpi_format_exception(status));
-		return -ENODEV;
-	}
+	if (!p->uartclk)
+		p->uartclk = (unsigned int)id->driver_data;
 
-	/* Fix Haswell issue where the clocks do not get enabled */
-	if (!strcmp(id->id, "INT33C4") || !strcmp(id->id, "INT33C5")) {
-		reg = readl(p->membase + LPSS_PRV_CLOCK_PARAMS);
-		writel(reg | 1, p->membase + LPSS_PRV_CLOCK_PARAMS);
-	}
+	up->dma = devm_kzalloc(p->dev, sizeof(*up->dma), GFP_KERNEL);
+	if (!up->dma)
+		return -ENOMEM;
+
+	up->dma->rxconf.src_maxburst = p->fifosize / 4;
+	up->dma->txconf.dst_maxburst = p->fifosize / 4;
 
 	return 0;
 }
 #else
-static inline int dw8250_probe_acpi(struct uart_port *p)
+static inline int dw8250_probe_acpi(struct uart_8250_port *up)
 {
 	return -ENODEV;
 }
@@ -266,7 +221,11 @@ static void dw8250_setup_port(struct uart_8250_port *up)
 		p->flags |= UPF_FIXED_TYPE;
 		p->fifosize = DW_UART_CPR_FIFO_SIZE(reg);
 		up->tx_loadsz = p->fifosize;
+		up->capabilities = UART_CAP_FIFO;
 	}
+
+	if (reg & DW_UART_CPR_AFCE_MODE)
+		up->capabilities |= UART_CAP_AFE;
 }
 
 static int dw8250_probe(struct platform_device *pdev)
@@ -286,17 +245,30 @@ static int dw8250_probe(struct platform_device *pdev)
 	uart.port.mapbase = regs->start;
 	uart.port.irq = irq->start;
 	uart.port.handle_irq = dw8250_handle_irq;
+	uart.port.pm = dw8250_do_pm;
 	uart.port.type = PORT_8250;
 	uart.port.flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_FIXED_PORT;
 	uart.port.dev = &pdev->dev;
 
-	uart.port.membase = ioremap(regs->start, resource_size(regs));
+	uart.port.membase = devm_ioremap(&pdev->dev, regs->start,
+					 resource_size(regs));
 	if (!uart.port.membase)
 		return -ENOMEM;
 
+	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->clk = devm_clk_get(&pdev->dev, NULL);
+	if (!IS_ERR(data->clk)) {
+		clk_prepare_enable(data->clk);
+		uart.port.uartclk = clk_get_rate(data->clk);
+	}
+
 	uart.port.iotype = UPIO_MEM;
 	uart.port.serial_in = dw8250_serial_in;
 	uart.port.serial_out = dw8250_serial_out;
+	uart.port.private_data = data;
 
 	dw8250_setup_port(&uart);
 
@@ -305,25 +277,22 @@ static int dw8250_probe(struct platform_device *pdev)
 		if (err)
 			return err;
 	} else if (ACPI_HANDLE(&pdev->dev)) {
-		err = dw8250_probe_acpi(&uart.port);
+		err = dw8250_probe_acpi(&uart);
 		if (err)
 			return err;
 	} else {
 		return -ENODEV;
 	}
 
-	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
-	if (!data)
-		return -ENOMEM;
-
-	uart.port.private_data = data;
-
 	data->line = serial8250_register_8250_port(&uart);
 	if (data->line < 0)
 		return data->line;
 
 	platform_set_drvdata(pdev, data);
 
+	pm_runtime_set_active(&pdev->dev);
+	pm_runtime_enable(&pdev->dev);
+
 	return 0;
 }
 
@@ -331,34 +300,66 @@ static int dw8250_remove(struct platform_device *pdev)
 {
 	struct dw8250_data *data = platform_get_drvdata(pdev);
 
+	pm_runtime_get_sync(&pdev->dev);
+
 	serial8250_unregister_port(data->line);
 
+	if (!IS_ERR(data->clk))
+		clk_disable_unprepare(data->clk);
+
+	pm_runtime_disable(&pdev->dev);
+	pm_runtime_put_noidle(&pdev->dev);
+
 	return 0;
 }
 
 #ifdef CONFIG_PM
-static int dw8250_suspend(struct platform_device *pdev, pm_message_t state)
+static int dw8250_suspend(struct device *dev)
 {
-	struct dw8250_data *data = platform_get_drvdata(pdev);
+	struct dw8250_data *data = dev_get_drvdata(dev);
 
 	serial8250_suspend_port(data->line);
 
 	return 0;
 }
 
-static int dw8250_resume(struct platform_device *pdev)
+static int dw8250_resume(struct device *dev)
 {
-	struct dw8250_data *data = platform_get_drvdata(pdev);
+	struct dw8250_data *data = dev_get_drvdata(dev);
 
 	serial8250_resume_port(data->line);
 
 	return 0;
 }
-#else
-#define dw8250_suspend NULL
-#define dw8250_resume NULL
 #endif /* CONFIG_PM */
 
+#ifdef CONFIG_PM_RUNTIME
+static int dw8250_runtime_suspend(struct device *dev)
+{
+	struct dw8250_data *data = dev_get_drvdata(dev);
+
+	if (!IS_ERR(data->clk))
+		clk_disable_unprepare(data->clk);
+
+	return 0;
+}
+
+static int dw8250_runtime_resume(struct device *dev)
+{
+	struct dw8250_data *data = dev_get_drvdata(dev);
+
+	if (!IS_ERR(data->clk))
+		clk_prepare_enable(data->clk);
+
+	return 0;
+}
+#endif
+
+static const struct dev_pm_ops dw8250_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(dw8250_suspend, dw8250_resume)
+	SET_RUNTIME_PM_OPS(dw8250_runtime_suspend, dw8250_runtime_resume, NULL)
+};
+
 static const struct of_device_id dw8250_of_match[] = {
 	{ .compatible = "snps,dw-apb-uart" },
 	{ /* Sentinel */ }
@@ -366,8 +367,9 @@ static const struct of_device_id dw8250_of_match[] = {
 MODULE_DEVICE_TABLE(of, dw8250_of_match);
 
 static const struct acpi_device_id dw8250_acpi_match[] = {
-	{ "INT33C4", 100000000 },
-	{ "INT33C5", 100000000 },
+	{ "INT33C4", 0 },
+	{ "INT33C5", 0 },
+	{ "80860F0A", 0 },
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, dw8250_acpi_match);
@@ -376,13 +378,12 @@ static struct platform_driver dw8250_platform_driver = {
 	.driver = {
 		.name		= "dw-apb-uart",
 		.owner		= THIS_MODULE,
+		.pm		= &dw8250_pm_ops,
 		.of_match_table	= dw8250_of_match,
 		.acpi_match_table = ACPI_PTR(dw8250_acpi_match),
 	},
 	.probe			= dw8250_probe,
 	.remove			= dw8250_remove,
-	.suspend		= dw8250_suspend,
-	.resume			= dw8250_resume,
 };
 
 module_platform_driver(dw8250_platform_driver);
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index aa76825229dc..26e3a97ab157 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1554,6 +1554,7 @@ pci_wch_ch353_setup(struct serial_private *priv,
 #define PCI_DEVICE_ID_PLX_CRONYX_OMEGA	0xc001
 #define PCI_DEVICE_ID_INTEL_PATSBURG_KT 0x1d3d
 #define PCI_VENDOR_ID_WCH		0x4348
+#define PCI_DEVICE_ID_WCH_CH352_2S	0x3253
 #define PCI_DEVICE_ID_WCH_CH353_4S	0x3453
 #define PCI_DEVICE_ID_WCH_CH353_2S1PF	0x5046
 #define PCI_DEVICE_ID_WCH_CH353_2S1P	0x7053
@@ -2172,6 +2173,14 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.subdevice      = PCI_ANY_ID,
 		.setup          = pci_wch_ch353_setup,
 	},
+	/* WCH CH352 2S card (16550 clone) */
+	{
+		.vendor		= PCI_VENDOR_ID_WCH,
+		.device		= PCI_DEVICE_ID_WCH_CH352_2S,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= pci_wch_ch353_setup,
+	},
 	/*
 	 * ASIX devices with FIFO bug
 	 */
@@ -4870,6 +4879,10 @@ static struct pci_device_id serial_pci_tbl[] = {
 		PCI_ANY_ID, PCI_ANY_ID,
 		0, 0, pbn_b0_bt_2_115200 },
 
+	{	PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH352_2S,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0, 0, pbn_b0_bt_2_115200 },
+
 	/*
 	 * Commtech, Inc. Fastcom adapters
 	 */
diff --git a/drivers/tty/serial/8250/8250_pnp.c b/drivers/tty/serial/8250/8250_pnp.c
index b3455a970a1d..35d9ab95c5cb 100644
--- a/drivers/tty/serial/8250/8250_pnp.c
+++ b/drivers/tty/serial/8250/8250_pnp.c
@@ -429,7 +429,6 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 {
 	struct uart_8250_port uart;
 	int ret, line, flags = dev_id->driver_data;
-	struct resource *res = NULL;
 
 	if (flags & UNKNOWN_DEV) {
 		ret = serial_pnp_guess_board(dev);
@@ -440,12 +439,11 @@ serial_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *dev_id)
 	memset(&uart, 0, sizeof(uart));
 	if (pnp_irq_valid(dev, 0))
 		uart.port.irq = pnp_irq(dev, 0);
-	if ((flags & CIR_PORT) && pnp_port_valid(dev, 2))
-		res = pnp_get_resource(dev, IORESOURCE_IO, 2);
-	else if (pnp_port_valid(dev, 0))
-		res = pnp_get_resource(dev, IORESOURCE_IO, 0);
-	if (pnp_resource_enabled(res)) {
-		uart.port.iobase = res->start;
+	if ((flags & CIR_PORT) && pnp_port_valid(dev, 2)) {
+		uart.port.iobase = pnp_port_start(dev, 2);
+		uart.port.iotype = UPIO_PORT;
+	} else if (pnp_port_valid(dev, 0)) {
+		uart.port.iobase = pnp_port_start(dev, 0);
 		uart.port.iotype = UPIO_PORT;
 	} else if (pnp_mem_valid(dev, 0)) {
 		uart.port.mapbase = pnp_mem_start(dev, 0);
diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig
index 2ef9537bcb2c..80fe91e64a52 100644
--- a/drivers/tty/serial/8250/Kconfig
+++ b/drivers/tty/serial/8250/Kconfig
@@ -33,6 +33,23 @@ config SERIAL_8250
 	  Most people will say Y or M here, so that they can use serial mice,
 	  modems and similar devices connecting to the standard serial ports.
 
+config SERIAL_8250_DEPRECATED_OPTIONS
+	bool "Support 8250_core.* kernel options (DEPRECATED)"
+	depends on SERIAL_8250
+	default y
+	---help---
+	  In 3.7 we renamed 8250 to 8250_core by mistake, so now we have to
+	  accept kernel parameters in both forms like 8250_core.nr_uarts=4 and
+	  8250.nr_uarts=4. We now renamed the module back to 8250, but if
+	  anybody noticed in 3.7 and changed their userspace we still have to
+	  keep the 8350_core.* options around until they revert the changes
+	  they already did.
+
+	  If 8250 is built as a module, this adds 8250_core alias instead. 
+
+	  If you did not notice yet and/or you have userspace from pre-3.7, it
+	  is safe (and recommended) to say N here.
+
 config SERIAL_8250_PNP
 	bool "8250/16550 PNP device support" if EXPERT
 	depends on SERIAL_8250 && PNP
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index a23838a4d535..36d68d054307 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -2,10 +2,10 @@
 # Makefile for the 8250 serial device drivers.
 #
 
-obj-$(CONFIG_SERIAL_8250)		+= 8250_core.o
-8250_core-y				:= 8250.o
-8250_core-$(CONFIG_SERIAL_8250_PNP)	+= 8250_pnp.o
-8250_core-$(CONFIG_SERIAL_8250_DMA)	+= 8250_dma.o
+obj-$(CONFIG_SERIAL_8250)		+= 8250.o
+8250-y					:= 8250_core.o
+8250-$(CONFIG_SERIAL_8250_PNP)		+= 8250_pnp.o
+8250-$(CONFIG_SERIAL_8250_DMA)		+= 8250_dma.o
 obj-$(CONFIG_SERIAL_8250_GSC)		+= 8250_gsc.o
 obj-$(CONFIG_SERIAL_8250_PCI)		+= 8250_pci.o
 obj-$(CONFIG_SERIAL_8250_HP300)		+= 8250_hp300.o
diff --git a/drivers/tty/serial/8250/serial_cs.c b/drivers/tty/serial/8250/serial_cs.c
index b7d48b346393..1b74b88e1e1e 100644
--- a/drivers/tty/serial/8250/serial_cs.c
+++ b/drivers/tty/serial/8250/serial_cs.c
@@ -852,18 +852,6 @@ static struct pcmcia_driver serial_cs_driver = {
 	.suspend	= serial_suspend,
 	.resume		= serial_resume,
 };
-
-static int __init init_serial_cs(void)
-{
-	return pcmcia_register_driver(&serial_cs_driver);
-}
-
-static void __exit exit_serial_cs(void)
-{
-	pcmcia_unregister_driver(&serial_cs_driver);
-}
-
-module_init(init_serial_cs);
-module_exit(exit_serial_cs);
+module_pcmcia_driver(serial_cs_driver);
 
 MODULE_LICENSE("GPL");