diff options
Diffstat (limited to 'drivers/spi')
| -rw-r--r-- | drivers/spi/Kconfig | 14 | ||||
| -rw-r--r-- | drivers/spi/Makefile | 4 | ||||
| -rw-r--r-- | drivers/spi/spi-lp8841-rtc.c | 256 | ||||
| -rw-r--r-- | drivers/spi/spi-pl022.c | 7 | ||||
| -rw-r--r-- | drivers/spi/spi-pxa2xx-dma.c | 8 | ||||
| -rw-r--r-- | drivers/spi/spi-pxa2xx-pci.c | 13 | ||||
| -rw-r--r-- | drivers/spi/spi-pxa2xx.c | 151 | ||||
| -rw-r--r-- | drivers/spi/spi-pxa2xx.h | 37 | ||||
| -rw-r--r-- | drivers/spi/spi.c | 336 |
9 files changed, 730 insertions, 96 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 77d3202f163d..c2a0404923f9 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -294,6 +294,16 @@ config SPI_LM70_LLP which interfaces to an LM70 temperature sensor using a parallel port. +config SPI_LP8841_RTC + tristate "ICP DAS LP-8841 SPI Controller for RTC" + depends on MACH_PXA27X_DT || COMPILE_TEST + help + This driver provides an SPI master device to drive Maxim + DS-1302 real time clock. + + Say N here unless you plan to run the kernel on an ICP DAS + LP-8x4x industrial computer. + config SPI_MPC52xx tristate "Freescale MPC52xx SPI (non-PSC) controller support" depends on PPC_MPC52xx @@ -445,10 +455,6 @@ config SPI_PPC4xx help This selects a driver for the PPC4xx SPI Controller. -config SPI_PXA2XX_DMA - def_bool y - depends on SPI_PXA2XX - config SPI_PXA2XX tristate "PXA2xx SSP SPI master" depends on (ARCH_PXA || PCI || ACPI) diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 7ad880684a85..fbb255c5a608 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -47,6 +47,7 @@ obj-$(CONFIG_SPI_GPIO) += spi-gpio.o obj-$(CONFIG_SPI_IMG_SPFI) += spi-img-spfi.o obj-$(CONFIG_SPI_IMX) += spi-imx.o obj-$(CONFIG_SPI_LM70_LLP) += spi-lm70llp.o +obj-$(CONFIG_SPI_LP8841_RTC) += spi-lp8841-rtc.o obj-$(CONFIG_SPI_MESON_SPIFC) += spi-meson-spifc.o obj-$(CONFIG_SPI_MPC512x_PSC) += spi-mpc512x-psc.o obj-$(CONFIG_SPI_MPC52xx_PSC) += spi-mpc52xx-psc.o @@ -63,8 +64,7 @@ obj-$(CONFIG_SPI_TI_QSPI) += spi-ti-qspi.o obj-$(CONFIG_SPI_ORION) += spi-orion.o obj-$(CONFIG_SPI_PL022) += spi-pl022.o obj-$(CONFIG_SPI_PPC4xx) += spi-ppc4xx.o -spi-pxa2xx-platform-objs := spi-pxa2xx.o -spi-pxa2xx-platform-$(CONFIG_SPI_PXA2XX_DMA) += spi-pxa2xx-dma.o +spi-pxa2xx-platform-objs := spi-pxa2xx.o spi-pxa2xx-dma.o obj-$(CONFIG_SPI_PXA2XX) += spi-pxa2xx-platform.o obj-$(CONFIG_SPI_PXA2XX_PCI) += spi-pxa2xx-pci.o obj-$(CONFIG_SPI_QUP) += spi-qup.o diff --git a/drivers/spi/spi-lp8841-rtc.c b/drivers/spi/spi-lp8841-rtc.c new file mode 100644 index 000000000000..faa577d282c0 --- /dev/null +++ b/drivers/spi/spi-lp8841-rtc.c @@ -0,0 +1,256 @@ +/* + * SPI master driver for ICP DAS LP-8841 RTC + * + * Copyright (C) 2016 Sergei Ianovich + * + * based on + * + * Dallas DS1302 RTC Support + * Copyright (C) 2002 David McCullough + * Copyright (C) 2003 - 2007 Paul Mundt + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ +#include <linux/delay.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/spi/spi.h> + +#define DRIVER_NAME "spi_lp8841_rtc" + +#define SPI_LP8841_RTC_CE 0x01 +#define SPI_LP8841_RTC_CLK 0x02 +#define SPI_LP8841_RTC_nWE 0x04 +#define SPI_LP8841_RTC_MOSI 0x08 +#define SPI_LP8841_RTC_MISO 0x01 + +/* + * REVISIT If there is support for SPI_3WIRE and SPI_LSB_FIRST in SPI + * GPIO driver, this SPI driver can be replaced by a simple GPIO driver + * providing 3 GPIO pins. + */ + +struct spi_lp8841_rtc { + void *iomem; + unsigned long state; +}; + +static inline void +setsck(struct spi_lp8841_rtc *data, int is_on) +{ + if (is_on) + data->state |= SPI_LP8841_RTC_CLK; + else + data->state &= ~SPI_LP8841_RTC_CLK; + writeb(data->state, data->iomem); +} + +static inline void +setmosi(struct spi_lp8841_rtc *data, int is_on) +{ + if (is_on) + data->state |= SPI_LP8841_RTC_MOSI; + else + data->state &= ~SPI_LP8841_RTC_MOSI; + writeb(data->state, data->iomem); +} + +static inline int +getmiso(struct spi_lp8841_rtc *data) +{ + return ioread8(data->iomem) & SPI_LP8841_RTC_MISO; +} + +static inline u32 +bitbang_txrx_be_cpha0_lsb(struct spi_lp8841_rtc *data, + unsigned usecs, unsigned cpol, unsigned flags, + u32 word, u8 bits) +{ + /* if (cpol == 0) this is SPI_MODE_0; else this is SPI_MODE_2 */ + + u32 shift = 32 - bits; + /* clock starts at inactive polarity */ + for (; likely(bits); bits--) { + + /* setup LSB (to slave) on leading edge */ + if ((flags & SPI_MASTER_NO_TX) == 0) + setmosi(data, (word & 1)); + + usleep_range(usecs, usecs + 1); /* T(setup) */ + + /* sample LSB (from slave) on trailing edge */ + word >>= 1; + if ((flags & SPI_MASTER_NO_RX) == 0) + word |= (getmiso(data) << 31); + + setsck(data, !cpol); + usleep_range(usecs, usecs + 1); + + setsck(data, cpol); + } + + word >>= shift; + return word; +} + +static int +spi_lp8841_rtc_transfer_one(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *t) +{ + struct spi_lp8841_rtc *data = spi_master_get_devdata(master); + unsigned count = t->len; + const u8 *tx = t->tx_buf; + u8 *rx = t->rx_buf; + u8 word = 0; + int ret = 0; + + if (tx) { + data->state &= ~SPI_LP8841_RTC_nWE; + writeb(data->state, data->iomem); + while (likely(count > 0)) { + word = *tx++; + bitbang_txrx_be_cpha0_lsb(data, 1, 0, + SPI_MASTER_NO_RX, word, 8); + count--; + } + } else if (rx) { + data->state |= SPI_LP8841_RTC_nWE; + writeb(data->state, data->iomem); + while (likely(count > 0)) { + word = bitbang_txrx_be_cpha0_lsb(data, 1, 0, + SPI_MASTER_NO_TX, word, 8); + *rx++ = word; + count--; + } + } else { + ret = -EINVAL; + } + + spi_finalize_current_transfer(master); + + return ret; +} + +static void +spi_lp8841_rtc_set_cs(struct spi_device *spi, bool enable) +{ + struct spi_lp8841_rtc *data = spi_master_get_devdata(spi->master); + + data->state = 0; + writeb(data->state, data->iomem); + if (enable) { + usleep_range(4, 5); + data->state |= SPI_LP8841_RTC_CE; + writeb(data->state, data->iomem); + usleep_range(4, 5); + } +} + +static int +spi_lp8841_rtc_setup(struct spi_device *spi) +{ + if ((spi->mode & SPI_CS_HIGH) == 0) { + dev_err(&spi->dev, "unsupported active low chip select\n"); + return -EINVAL; + } + + if ((spi->mode & SPI_LSB_FIRST) == 0) { + dev_err(&spi->dev, "unsupported MSB first mode\n"); + return -EINVAL; + } + + if ((spi->mode & SPI_3WIRE) == 0) { + dev_err(&spi->dev, "unsupported wiring. 3 wires required\n"); + return -EINVAL; + } + + return 0; +} + +#ifdef CONFIG_OF +static const struct of_device_id spi_lp8841_rtc_dt_ids[] = { + { .compatible = "icpdas,lp8841-spi-rtc" }, + { } +}; + +MODULE_DEVICE_TABLE(of, spi_lp8841_rtc_dt_ids); +#endif + +static int +spi_lp8841_rtc_probe(struct platform_device *pdev) +{ + int ret; + struct spi_master *master; + struct spi_lp8841_rtc *data; + void *iomem; + + master = spi_alloc_master(&pdev->dev, sizeof(*data)); + if (!master) + return -ENOMEM; + platform_set_drvdata(pdev, master); + + master->flags = SPI_MASTER_HALF_DUPLEX; + master->mode_bits = SPI_CS_HIGH | SPI_3WIRE | SPI_LSB_FIRST; + + master->bus_num = pdev->id; + master->num_chipselect = 1; + master->setup = spi_lp8841_rtc_setup; + master->set_cs = spi_lp8841_rtc_set_cs; + master->transfer_one = spi_lp8841_rtc_transfer_one; + master->bits_per_word_mask = SPI_BPW_MASK(8); +#ifdef CONFIG_OF + master->dev.of_node = pdev->dev.of_node; +#endif + + data = spi_master_get_devdata(master); + + iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + data->iomem = devm_ioremap_resource(&pdev->dev, iomem); + ret = PTR_ERR_OR_ZERO(data->iomem); + if (ret) { + dev_err(&pdev->dev, "failed to get IO address\n"); + goto err_put_master; + } + + /* register with the SPI framework */ + ret = devm_spi_register_master(&pdev->dev, master); + if (ret) { + dev_err(&pdev->dev, "cannot register spi master\n"); + goto err_put_master; + } + + return ret; + + +err_put_master: + spi_master_put(master); + + return ret; +} + +MODULE_ALIAS("platform:" DRIVER_NAME); + +static struct platform_driver spi_lp8841_rtc_driver = { + .driver = { + .name = DRIVER_NAME, + .of_match_table = of_match_ptr(spi_lp8841_rtc_dt_ids), + }, + .probe = spi_lp8841_rtc_probe, +}; +module_platform_driver(spi_lp8841_rtc_driver); + +MODULE_DESCRIPTION("SPI master driver for ICP DAS LP-8841 RTC"); +MODULE_AUTHOR("Sergei Ianovich"); +MODULE_LICENSE("GPL"); diff --git a/drivers/spi/spi-pl022.c b/drivers/spi/spi-pl022.c index 5e5fd77e2711..f7f7ba17b40e 100644 --- a/drivers/spi/spi-pl022.c +++ b/drivers/spi/spi-pl022.c @@ -346,13 +346,6 @@ struct vendor_data { * @clk: outgoing clock "SPICLK" for the SPI bus * @master: SPI framework hookup * @master_info: controller-specific data from machine setup - * @kworker: thread struct for message pump - * @kworker_task: pointer to task for message pump kworker thread - * @pump_messages: work struct for scheduling work to the message pump - * @queue_lock: spinlock to syncronise access to message queue - * @queue: message queue - * @busy: message pump is busy - * @running: message pump is running * @pump_transfers: Tasklet used in Interrupt Transfer mode * @cur_msg: Pointer to current spi_message being processed * @cur_transfer: Pointer to current spi_transfer diff --git a/drivers/spi/spi-pxa2xx-dma.c b/drivers/spi/spi-pxa2xx-dma.c index bd8b369a343c..365fc22c3572 100644 --- a/drivers/spi/spi-pxa2xx-dma.c +++ b/drivers/spi/spi-pxa2xx-dma.c @@ -254,8 +254,8 @@ irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data) if (status & SSSR_ROR) { dev_err(&drv_data->pdev->dev, "FIFO overrun\n"); - dmaengine_terminate_all(drv_data->rx_chan); - dmaengine_terminate_all(drv_data->tx_chan); + dmaengine_terminate_async(drv_data->rx_chan); + dmaengine_terminate_async(drv_data->tx_chan); pxa2xx_spi_dma_transfer_complete(drv_data, true); return IRQ_HANDLED; @@ -331,13 +331,13 @@ int pxa2xx_spi_dma_setup(struct driver_data *drv_data) void pxa2xx_spi_dma_release(struct driver_data *drv_data) { if (drv_data->rx_chan) { - dmaengine_terminate_all(drv_data->rx_chan); + dmaengine_terminate_sync(drv_data->rx_chan); dma_release_channel(drv_data->rx_chan); sg_free_table(&drv_data->rx_sgt); drv_data->rx_chan = NULL; } if (drv_data->tx_chan) { - dmaengine_terminate_all(drv_data->tx_chan); + dmaengine_terminate_sync(drv_data->tx_chan); dma_release_channel(drv_data->tx_chan); sg_free_table(&drv_data->tx_sgt); drv_data->tx_chan = NULL; diff --git a/drivers/spi/spi-pxa2xx-pci.c b/drivers/spi/spi-pxa2xx-pci.c index d19d7f28aecb..520ed1dd5780 100644 --- a/drivers/spi/spi-pxa2xx-pci.c +++ b/drivers/spi/spi-pxa2xx-pci.c @@ -19,6 +19,7 @@ enum { PORT_BSW1, PORT_BSW2, PORT_QUARK_X1000, + PORT_LPT, }; struct pxa_spi_info { @@ -42,6 +43,9 @@ static struct dw_dma_slave bsw1_rx_param = { .src_id = 7 }; static struct dw_dma_slave bsw2_tx_param = { .dst_id = 8 }; static struct dw_dma_slave bsw2_rx_param = { .src_id = 9 }; +static struct dw_dma_slave lpt_tx_param = { .dst_id = 0 }; +static struct dw_dma_slave lpt_rx_param = { .src_id = 1 }; + static bool lpss_dma_filter(struct dma_chan *chan, void *param) { struct dw_dma_slave *dws = param; @@ -98,6 +102,14 @@ static struct pxa_spi_info spi_info_configs[] = { .num_chipselect = 1, .max_clk_rate = 50000000, }, + [PORT_LPT] = { + .type = LPSS_LPT_SSP, + .port_id = 0, + .num_chipselect = 1, + .max_clk_rate = 50000000, + .tx_param = &lpt_tx_param, + .rx_param = &lpt_rx_param, + }, }; static int pxa2xx_spi_pci_probe(struct pci_dev *dev, @@ -202,6 +214,7 @@ static const struct pci_device_id pxa2xx_spi_pci_devices[] = { { PCI_VDEVICE(INTEL, 0x228e), PORT_BSW0 }, { PCI_VDEVICE(INTEL, 0x2290), PORT_BSW1 }, { PCI_VDEVICE(INTEL, 0x22ac), PORT_BSW2 }, + { PCI_VDEVICE(INTEL, 0x9ce6), PORT_LPT }, { }, }; MODULE_DEVICE_TABLE(pci, pxa2xx_spi_pci_devices); diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c index ab9914ad8365..85e59a406a4c 100644 --- a/drivers/spi/spi-pxa2xx.c +++ b/drivers/spi/spi-pxa2xx.c @@ -65,8 +65,6 @@ MODULE_ALIAS("platform:pxa2xx-spi"); #define LPSS_GENERAL_REG_RXTO_HOLDOFF_DISABLE BIT(24) #define LPSS_CS_CONTROL_SW_MODE BIT(0) #define LPSS_CS_CONTROL_CS_HIGH BIT(1) -#define LPSS_CS_CONTROL_CS_SEL_SHIFT 8 -#define LPSS_CS_CONTROL_CS_SEL_MASK (3 << LPSS_CS_CONTROL_CS_SEL_SHIFT) #define LPSS_CAPS_CS_EN_SHIFT 9 #define LPSS_CAPS_CS_EN_MASK (0xf << LPSS_CAPS_CS_EN_SHIFT) @@ -82,6 +80,10 @@ struct lpss_config { u32 rx_threshold; u32 tx_threshold_lo; u32 tx_threshold_hi; + /* Chip select control */ + unsigned cs_sel_shift; + unsigned cs_sel_mask; + unsigned cs_num; }; /* Keep these sorted with enum pxa_ssp_type */ @@ -106,6 +108,19 @@ static const struct lpss_config lpss_platforms[] = { .tx_threshold_lo = 160, .tx_threshold_hi = 224, }, + { /* LPSS_BSW_SSP */ + .offset = 0x400, + .reg_general = 0x08, + .reg_ssp = 0x0c, + .reg_cs_ctrl = 0x18, + .reg_capabilities = -1, + .rx_threshold = 64, + .tx_threshold_lo = 160, + .tx_threshold_hi = 224, + .cs_sel_shift = 2, + .cs_sel_mask = 1 << 2, + .cs_num = 2, + }, { /* LPSS_SPT_SSP */ .offset = 0x200, .reg_general = -1, @@ -125,6 +140,8 @@ static const struct lpss_config lpss_platforms[] = { .rx_threshold = 1, .tx_threshold_lo = 16, .tx_threshold_hi = 48, + .cs_sel_shift = 8, + .cs_sel_mask = 3 << 8, }, }; @@ -139,6 +156,7 @@ static bool is_lpss_ssp(const struct driver_data *drv_data) switch (drv_data->ssp_type) { case LPSS_LPT_SSP: case LPSS_BYT_SSP: + case LPSS_BSW_SSP: case LPSS_SPT_SSP: case LPSS_BXT_SSP: return true; @@ -288,37 +306,50 @@ static void lpss_ssp_setup(struct driver_data *drv_data) } } +static void lpss_ssp_select_cs(struct driver_data *drv_data, + const struct lpss_config *config) +{ + u32 value, cs; + + if (!config->cs_sel_mask) + return; + + value = __lpss_ssp_read_priv(drv_data, config->reg_cs_ctrl); + + cs = drv_data->cur_msg->spi->chip_select; + cs <<= config->cs_sel_shift; + if (cs != (value & config->cs_sel_mask)) { + /* + * When switching another chip select output active the + * output must be selected first and wait 2 ssp_clk cycles + * before changing state to active. Otherwise a short + * glitch will occur on the previous chip select since + * output select is latched but state control is not. + */ + value &= ~config->cs_sel_mask; + value |= cs; + __lpss_ssp_write_priv(drv_data, + config->reg_cs_ctrl, value); + ndelay(1000000000 / + (drv_data->master->max_speed_hz / 2)); + } +} + static void lpss_ssp_cs_control(struct driver_data *drv_data, bool enable) { const struct lpss_config *config; - u32 value, cs; + u32 value; config = lpss_get_config(drv_data); + if (enable) + lpss_ssp_select_cs(drv_data, config); + value = __lpss_ssp_read_priv(drv_data, config->reg_cs_ctrl); - if (enable) { - cs = drv_data->cur_msg->spi->chip_select; - cs <<= LPSS_CS_CONTROL_CS_SEL_SHIFT; - if (cs != (value & LPSS_CS_CONTROL_CS_SEL_MASK)) { - /* - * When switching another chip select output active - * the output must be selected first and wait 2 ssp_clk - * cycles before changing state to active. Otherwise - * a short glitch will occur on the previous chip - * select since output select is latched but state - * control is not. - */ - value &= ~LPSS_CS_CONTROL_CS_SEL_MASK; - value |= cs; - __lpss_ssp_write_priv(drv_data, - config->reg_cs_ctrl, value); - ndelay(1000000000 / - (drv_data->master->max_speed_hz / 2)); - } + if (enable) value &= ~LPSS_CS_CONTROL_CS_HIGH; - } else { + else value |= LPSS_CS_CONTROL_CS_HIGH; - } __lpss_ssp_write_priv(drv_data, config->reg_cs_ctrl, value); } @@ -496,6 +527,7 @@ static void giveback(struct driver_data *drv_data) { struct spi_transfer* last_transfer; struct spi_message *msg; + unsigned long timeout; msg = drv_data->cur_msg; drv_data->cur_msg = NULL; @@ -508,6 +540,12 @@ static void giveback(struct driver_data *drv_data) if (last_transfer->delay_usecs) udelay(last_transfer->delay_usecs); + /* Wait until SSP becomes idle before deasserting the CS */ + timeout = jiffies + msecs_to_jiffies(10); + while (pxa2xx_spi_read(drv_data, SSSR) & SSSR_BSY && + !time_after(jiffies, timeout)) + cpu_relax(); + /* Drop chip select UNLESS cs_change is true or we are returning * a message with an error, or next message is for another chip */ @@ -572,7 +610,7 @@ static void int_error_stop(struct driver_data *drv_data, const char* msg) static void int_transfer_complete(struct driver_data *drv_data) { - /* Stop SSP */ + /* Clear and disable interrupts */ write_SSSR_CS(drv_data, drv_data->clear_sr); reset_sccr1(drv_data); if (!pxa25x_ssp_comp(drv_data)) @@ -957,8 +995,6 @@ static void pump_transfers(unsigned long data) drv_data->tx_end = drv_data->tx + transfer->len; drv_data->rx = transfer->rx_buf; drv_data->rx_end = drv_data->rx + transfer->len; - drv_data->rx_dma = transfer->rx_dma; - drv_data->tx_dma = transfer->tx_dma; drv_data->len = transfer->len; drv_data->write = drv_data->tx ? chip->write : null_writer; drv_data->read = drv_data->rx ? chip->read : null_reader; @@ -1001,19 +1037,6 @@ static void pump_transfers(unsigned long data) "pump_transfers: DMA burst size reduced to match bits_per_word\n"); } - /* NOTE: PXA25x_SSP _could_ use external clocking ... */ - cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits); - if (!pxa25x_ssp_comp(drv_data)) - dev_dbg(&message->spi->dev, "%u Hz actual, %s\n", - drv_data->master->max_speed_hz - / (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)), - chip->enable_dma ? "DMA" : "PIO"); - else - dev_dbg(&message->spi->dev, "%u Hz actual, %s\n", - drv_data->master->max_speed_hz / 2 - / (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)), - chip->enable_dma ? "DMA" : "PIO"); - message->state = RUNNING_STATE; drv_data->dma_mapped = 0; @@ -1040,6 +1063,19 @@ static void pump_transfers(unsigned long data) write_SSSR_CS(drv_data, drv_data->clear_sr); } + /* NOTE: PXA25x_SSP _could_ use external clocking ... */ + cr0 = pxa2xx_configure_sscr0(drv_data, clk_div, bits); + if (!pxa25x_ssp_comp(drv_data)) + dev_dbg(&message->spi->dev, "%u Hz actual, %s\n", + drv_data->master->max_speed_hz + / (1 + ((cr0 & SSCR0_SCR(0xfff)) >> 8)), + drv_data->dma_mapped ? "DMA" : "PIO"); + else + dev_dbg(&message->spi->dev, "%u Hz actual, %s\n", + drv_data->master->max_speed_hz / 2 + / (1 + ((cr0 & SSCR0_SCR(0x0ff)) >> 8)), + drv_data->dma_mapped ? "DMA" : "PIO"); + if (is_lpss_ssp(drv_data)) { if ((pxa2xx_spi_read(drv_data, SSIRF) & 0xff) != chip->lpss_rx_threshold) @@ -1166,6 +1202,7 @@ static int setup(struct spi_device *spi) break; case LPSS_LPT_SSP: case LPSS_BYT_SSP: + case LPSS_BSW_SSP: case LPSS_SPT_SSP: case LPSS_BXT_SSP: config = lpss_get_config(drv_data); @@ -1313,7 +1350,7 @@ static const struct acpi_device_id pxa2xx_spi_acpi_match[] = { { "INT3430", LPSS_LPT_SSP }, { "INT3431", LPSS_LPT_SSP }, { "80860F0E", LPSS_BYT_SSP }, - { "8086228E", LPSS_BYT_SSP }, + { "8086228E", LPSS_BSW_SSP }, { }, }; MODULE_DEVICE_TABLE(acpi, pxa2xx_spi_acpi_match); @@ -1347,10 +1384,14 @@ static const struct pci_device_id pxa2xx_spi_pci_compound_match[] = { /* SPT-H */ { PCI_VDEVICE(INTEL, 0xa129), LPSS_SPT_SSP }, { PCI_VDEVICE(INTEL, 0xa12a), LPSS_SPT_SSP }, - /* BXT */ + /* BXT A-Step */ { PCI_VDEVICE(INTEL, 0x0ac2), LPSS_BXT_SSP }, { PCI_VDEVICE(INTEL, 0x0ac4), LPSS_BXT_SSP }, { PCI_VDEVICE(INTEL, 0x0ac6), LPSS_BXT_SSP }, + /* BXT B-Step */ + { PCI_VDEVICE(INTEL, 0x1ac2), LPSS_BXT_SSP }, + { PCI_VDEVICE(INTEL, 0x1ac4), LPSS_BXT_SSP }, + { PCI_VDEVICE(INTEL, 0x1ac6), LPSS_BXT_SSP }, /* APL */ { PCI_VDEVICE(INTEL, 0x5ac2), LPSS_BXT_SSP }, { PCI_VDEVICE(INTEL, 0x5ac4), LPSS_BXT_SSP }, @@ -1438,6 +1479,29 @@ pxa2xx_spi_init_pdata(struct platform_device *pdev) } #endif +static int pxa2xx_spi_fw_translate_cs(struct spi_master *master, unsigned cs) +{ + struct driver_data *drv_data = spi_master_get_devdata(master); + + if (has_acpi_companion(&drv_data->pdev->dev)) { + switch (drv_data->ssp_type) { + /* + * For Atoms the ACPI DeviceSelection used by the Windows + * driver starts from 1 instead of 0 so translate it here + * to match what Linux expects. + */ + case LPSS_BYT_SSP: + case LPSS_BSW_SSP: + return cs - 1; + + default: + break; + } + } + + return cs; +} + static int pxa2xx_spi_probe(struct platform_device *pdev) { struct device *dev = &pdev->dev; @@ -1490,6 +1554,7 @@ static int pxa2xx_spi_probe(struct platform_device *pdev) master->setup = setup; master->transfer_one_message = pxa2xx_spi_transfer_one_message; master->unprepare_transfer_hardware = pxa2xx_spi_unprepare_transfer; + master->fw_translate_cs = pxa2xx_spi_fw_translate_cs; master->auto_runtime_pm = true; drv_data->ssp_type = ssp->type; @@ -1576,6 +1641,8 @@ static int pxa2xx_spi_probe(struct platform_device *pdev) tmp &= LPSS_CAPS_CS_EN_MASK; tmp >>= LPSS_CAPS_CS_EN_SHIFT; platform_info->num_chipselect = ffz(tmp); + } else if (config->cs_num) { + platform_info->num_chipselect = config->cs_num; } } master->num_chipselect = platform_info->num_chipselect; diff --git a/drivers/spi/spi-pxa2xx.h b/drivers/spi/spi-pxa2xx.h index 58efa98313aa..a1ef88948144 100644 --- a/drivers/spi/spi-pxa2xx.h +++ b/drivers/spi/spi-pxa2xx.h @@ -69,8 +69,6 @@ struct driver_data { void *rx; void *rx_end; int dma_mapped; - dma_addr_t rx_dma; - dma_addr_t tx_dma; size_t rx_map_len; size_t tx_map_len; u8 n_bytes; @@ -147,20 +145,9 @@ static inline void write_SSSR_CS(struct driver_data *drv_data, u32 val) extern int pxa2xx_spi_flush(struct driver_data *drv_data); extern void *pxa2xx_spi_next_transfer(struct driver_data *drv_data); -/* - * Select the right DMA implementation. - */ -#if defined(CONFIG_SPI_PXA2XX_DMA) -#define SPI_PXA2XX_USE_DMA 1 #define MAX_DMA_LEN SZ_64K #define DEFAULT_DMA_CR1 (SSCR1_TSRE | SSCR1_RSRE | SSCR1_TRAIL) -#else -#undef SPI_PXA2XX_USE_DMA -#define MAX_DMA_LEN 0 -#define DEFAULT_DMA_CR1 0 -#endif -#ifdef SPI_PXA2XX_USE_DMA extern bool pxa2xx_spi_dma_is_possible(size_t len); extern int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data); extern irqreturn_t pxa2xx_spi_dma_transfer(struct driver_data *drv_data); @@ -173,29 +160,5 @@ extern int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip, u8 bits_per_word, u32 *burst_code, u32 *threshold); -#else -static inline bool pxa2xx_spi_dma_is_possible(size_t len) { return false; } -static inline int pxa2xx_spi_map_dma_buffers(struct driver_data *drv_data) -{ - return 0; -} -#define pxa2xx_spi_dma_transfer NULL -static inline void pxa2xx_spi_dma_prepare(struct driver_data *drv_data, - u32 dma_burst) {} -static inline void pxa2xx_spi_dma_start(struct driver_data *drv_data) {} -static inline int pxa2xx_spi_dma_setup(struct driver_data *drv_data) -{ - return 0; -} -static inline void pxa2xx_spi_dma_release(struct driver_data *drv_data) {} -static inline int pxa2xx_spi_set_dma_burst_and_threshold(struct chip_data *chip, - struct spi_device *spi, - u8 bits_per_word, - u32 *burst_code, - u32 *threshold) -{ - return -ENODEV; -} -#endif #endif /* SPI_PXA2XX_H */ diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index b30f03a99dfd..de2f2f90d799 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -144,6 +144,8 @@ SPI_STATISTICS_TRANSFER_BYTES_HISTO(14, "16384-32767"); SPI_STATISTICS_TRANSFER_BYTES_HISTO(15, "32768-65535"); SPI_STATISTICS_TRANSFER_BYTES_HISTO(16, "65536+"); +SPI_STATISTICS_SHOW(transfers_split_maxsize, "%lu"); + static struct attribute *spi_dev_attrs[] = { &dev_attr_modalias.attr, NULL, @@ -181,6 +183,7 @@ static struct attribute *spi_device_statistics_attrs[] = { &dev_attr_spi_device_transfer_bytes_histo14.attr, &dev_attr_spi_device_transfer_bytes_histo15.attr, &dev_attr_spi_device_transfer_bytes_histo16.attr, + &dev_attr_spi_device_transfers_split_maxsize.attr, NULL, }; @@ -223,6 +226,7 @@ static struct attribute *spi_master_statistics_attrs[] = { &dev_attr_spi_master_transfer_bytes_histo14.attr, &dev_attr_spi_master_transfer_bytes_histo15.attr, &dev_attr_spi_master_transfer_bytes_histo16.attr, + &dev_attr_spi_master_transfers_split_maxsize.attr, NULL, }; @@ -1024,6 +1028,8 @@ out: if (msg->status && master->handle_err) master->handle_err(master, msg); + spi_res_release(master, msg); + spi_finalize_current_message(master); return ret; @@ -2043,6 +2049,336 @@ struct spi_master *spi_busnum_to_master(u16 bus_num) } EXPORT_SYMBOL_GPL(spi_busnum_to_master); +/*-------------------------------------------------------------------------*/ + +/* Core methods for SPI resource management */ + +/** + * spi_res_alloc - allocate a spi resource that is life-cycle managed + * during the processing of a spi_message while using + * spi_transfer_one + * @spi: the spi device for which we allocate memory + * @release: the release code to execute for this resource + * @size: size to alloc and return + * @gfp: GFP allocation flags + * + * Return: the pointer to the allocated data + * + * This may get enhanced in the future to allocate from a memory pool + * of the @spi_device or @spi_master to avoid repeated allocations. + */ +void *spi_res_alloc(struct spi_device *spi, + spi_res_release_t release, + size_t size, gfp_t gfp) +{ + struct spi_res *sres; + + sres = kzalloc(sizeof(*sres) + size, gfp); + if (!sres) + return NULL; + + INIT_LIST_HEAD(&sres->entry); + sres->release = release; + + return sres->data; +} +EXPORT_SYMBOL_GPL(spi_res_alloc); + +/** + * spi_res_free - free an spi resource + * @res: pointer to the custom data of a resource + * + */ +void spi_res_free(void *res) +{ + struct spi_res *sres = container_of(res, struct spi_res, data); + + if (!res) + return; + + WARN_ON(!list_empty(&sres->entry)); + kfree(sres); +} +EXPORT_SYMBOL_GPL(spi_res_free); + +/** + * spi_res_add - add a spi_res to the spi_message + * @message: the spi message + * @res: the spi_resource + */ +void spi_res_add(struct spi_message *message, void *res) +{ + struct spi_res *sres = container_of(res, struct spi_res, data); + + WARN_ON(!list_empty(&sres->entry)); + list_add_tail(&sres->entry, &message->resources); +} +EXPORT_SYMBOL_GPL(spi_res_add); + +/** + * spi_res_release - release all spi resources for this message + * @master: the @spi_master + * @message: the @spi_message + */ +void spi_res_release(struct spi_master *master, + struct spi_message *message) +{ + struct spi_res *res; + + while (!list_empty(&message->resources)) { + res = list_last_entry(&message->resources, + struct spi_res, entry); + + if (res->release) + res->release(master, message, res->data); + + list_del(&res->entry); + + kfree(res); + } +} +EXPORT_SYMBOL_GPL(spi_res_release); + +/*-------------------------------------------------------------------------*/ + +/* Core methods for spi_message alterations */ + +static void __spi_replace_transfers_release(struct spi_master *master, + struct spi_message *msg, + void *res) +{ + struct spi_replaced_transfers *rxfer = res; + size_t i; + + /* call extra callback if requested */ + if (rxfer->release) + rxfer->release(master, msg, res); + + /* insert replaced transfers back into the message */ + list_splice(&rxfer->replaced_transfers, rxfer->replaced_after); + + /* remove the formerly inserted entries */ + for (i = 0; i < rxfer->inserted; i++) + list_del(&rxfer->inserted_transfers[i].transfer_list); +} + +/** + * spi_replace_transfers - replace transfers with several transfers + * and register change with spi_message.resources + * @msg: the spi_message we work upon + * @xfer_first: the first spi_transfer we want to replace + * @remove: number of transfers to remove + * @insert: the number of transfers we want to insert instead + * @release: extra release code necessary in some circumstances + * @extradatasize: extra data to allocate (with alignment guarantees + * of struct @spi_transfer) + * @gfp: gfp flags + * + * Returns: pointer to @spi_replaced_transfers, + * PTR_ERR(...) in case of errors. + */ +struct spi_replaced_transfers *spi_replace_transfers( + struct spi_message *msg, + struct spi_transfer *xfer_first, + size_t remove, + size_t insert, + spi_replaced_release_t release, + size_t extradatasize, + gfp_t gfp) +{ + struct spi_replaced_transfers *rxfer; + struct spi_transfer *xfer; + size_t i; + + /* allocate the structure using spi_res */ + rxfer = spi_res_alloc(msg->spi, __spi_replace_transfers_release, + insert * sizeof(struct spi_transfer) + + sizeof(struct spi_replaced_transfers) + + extradatasize, + gfp); + if (!rxfer) + return ERR_PTR(-ENOMEM); + + /* the release code to invoke before running the generic release */ + rxfer->release = release; + + /* assign extradata */ + if (extradatasize) + rxfer->extradata = + &rxfer->inserted_transfers[insert]; + + /* init the replaced_transfers list */ + INIT_LIST_HEAD(&rxfer->replaced_transfers); + + /* assign the list_entry after which we should reinsert + * the @replaced_transfers - it may be spi_message.messages! + */ + rxfer->replaced_after = xfer_first->transfer_list.prev; + + /* remove the requested number of transfers */ + for (i = 0; i < remove; i++) { + /* if the entry after replaced_after it is msg->transfers + * then we have been requested to remove more transfers + * than are in the list + */ + if (rxfer->replaced_after->next == &msg->transfers) { + dev_err(&msg->spi->dev, + "requested to remove more spi_transfers than are available\n"); + /* insert replaced transfers back into the message */ + list_splice(&rxfer->replaced_transfers, + rxfer->replaced_after); + + /* free the spi_replace_transfer structure */ + spi_res_free(rxfer); + + /* and return with an error */ + return ERR_PTR(-EINVAL); + } + + /* remove the entry after replaced_after from list of + * transfers and add it to list of replaced_transfers + */ + list_move_tail(rxfer->replaced_after->next, + &rxfer->replaced_transfers); + } + + /* create copy of the given xfer with identical settings + * based on the first transfer to get removed + */ + for (i = 0; i < insert; i++) { + /* we need to run in reverse order */ + xfer = &rxfer->inserted_transfers[insert - 1 - i]; + + /* copy all spi_transfer data */ + memcpy(xfer, xfer_first, sizeof(*xfer)); + + /* add to list */ + list_add(&xfer->transfer_list, rxfer->replaced_after); + + /* clear cs_change and delay_usecs for all but the last */ + if (i) { + xfer->cs_change = false; + xfer->delay_usecs = 0; + } + } + + /* set up inserted */ + rxfer->inserted = insert; + + /* and register it with spi_res/spi_message */ + spi_res_add(msg, rxfer); + + return rxfer; +} +EXPORT_SYMBOL_GPL(spi_replace_transfers); + +static int __spi_split_transfer_maxsize(struct spi_master *master, + struct spi_message *msg, + struct spi_transfer **xferp, + size_t maxsize, + gfp_t gfp) +{ + struct spi_transfer *xfer = *xferp, *xfers; + struct spi_replaced_transfers *srt; + size_t offset; + size_t count, i; + + /* warn once about this fact that we are splitting a transfer */ + dev_warn_once(&msg->spi->dev, + "spi_transfer of length %i exceed max length of %zu - needed to split transfers\n", + xfer->len, maxsize); + + /* calculate how many we have to replace */ + count = DIV_ROUND_UP(xfer->len, maxsize); + + /* create replacement */ + srt = spi_replace_transfers(msg, xfer, 1, count, NULL, 0, gfp); + if (IS_ERR(srt)) + return PTR_ERR(srt); + xfers = srt->inserted_transfers; + + /* now handle each of those newly inserted spi_transfers + * note that the replacements spi_transfers all are preset + * to the same values as *xferp, so tx_buf, rx_buf and len + * are all identical (as well as most others) + * so we just have to fix up len and the pointers. + * + * this also includes support for the depreciated + * spi_message.is_dma_mapped interface + */ + + /* the first transfer just needs the length modified, so we + * run it outside the loop + */ + xfers[0].len = min_t(size_t, maxsize, xfer[0].len); + + /* all the others need rx_buf/tx_buf also set */ + for (i = 1, offset = maxsize; i < count; offset += maxsize, i++) { + /* update rx_buf, tx_buf and dma */ + if (xfers[i].rx_buf) + xfers[i].rx_buf += offset; + if (xfers[i].rx_dma) + xfers[i].rx_dma += offset; + if (xfers[i].tx_buf) + xfers[i].tx_buf += offset; + if (xfers[i].tx_dma) + xfers[i].tx_dma += offset; + + /* update length */ + xfers[i].len = min(maxsize, xfers[i].len - offset); + } + + /* we set up xferp to the last entry we have inserted, + * so that we skip those already split transfers + */ + *xferp = &xfers[count - 1]; + + /* increment statistics counters */ + SPI_STATISTICS_INCREMENT_FIELD(&master->statistics, + transfers_split_maxsize); + SPI_STATISTICS_INCREMENT_FIELD(&msg->spi->statistics, + transfers_split_maxsize); + + return 0; +} + +/** + * spi_split_tranfers_maxsize - split spi transfers into multiple transfers + * when an individual transfer exceeds a + * certain size + * @master: the @spi_master for this transfer + * @msg: the @spi_message to transform + * @maxsize: the maximum when to apply this + * @gfp: GFP allocation flags + * + * Return: status of transformation + */ +int spi_split_transfers_maxsize(struct spi_master *master, + struct spi_message *msg, + size_t maxsize, + gfp_t gfp) +{ + struct spi_transfer *xfer; + int ret; + + /* iterate over the transfer_list, + * but note that xfer is advanced to the last transfer inserted + * to avoid checking sizes again unnecessarily (also xfer does + * potentiall belong to a different list by the time the + * replacement has happened + */ + list_for_each_entry(xfer, &msg->transfers, transfer_list) { + if (xfer->len > maxsize) { + ret = __spi_split_transfer_maxsize( + master, msg, &xfer, maxsize, gfp); + if (ret) + return ret; + } + } + + return 0; +} +EXPORT_SYMBOL_GPL(spi_split_transfers_maxsize); /*-------------------------------------------------------------------------*/ |
