diff options
Diffstat (limited to 'drivers/net/wireless/iwlwifi/iwl-3945-hw.h')
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-3945-hw.h | 213 |
1 files changed, 3 insertions, 210 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-3945-hw.h b/drivers/net/wireless/iwlwifi/iwl-3945-hw.h index 571815d7e8bf..ad612a8719f4 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945-hw.h +++ b/drivers/net/wireless/iwlwifi/iwl-3945-hw.h @@ -5,7 +5,7 @@ * * GPL LICENSE SUMMARY * - * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. + * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved. * * This program is free software; you can redistribute it and/or modify * it under the terms of version 2 of the GNU General Public License as @@ -30,7 +30,7 @@ * * BSD LICENSE * - * Copyright(c) 2005 - 2007 Intel Corporation. All rights reserved. + * Copyright(c) 2005 - 2008 Intel Corporation. All rights reserved. * All rights reserved. * * Redistribution and use in source and binary forms, with or without @@ -198,43 +198,27 @@ struct iwl3945_eeprom_temperature_corr { */ struct iwl3945_eeprom { u8 reserved0[16]; -#define EEPROM_DEVICE_ID (2*0x08) /* 2 bytes */ u16 device_id; /* abs.ofs: 16 */ u8 reserved1[2]; -#define EEPROM_PMC (2*0x0A) /* 2 bytes */ u16 pmc; /* abs.ofs: 20 */ u8 reserved2[20]; -#define EEPROM_MAC_ADDRESS (2*0x15) /* 6 bytes */ u8 mac_address[6]; /* abs.ofs: 42 */ u8 reserved3[58]; -#define EEPROM_BOARD_REVISION (2*0x35) /* 2 bytes */ u16 board_revision; /* abs.ofs: 106 */ u8 reserved4[11]; -#define EEPROM_BOARD_PBA_NUMBER (2*0x3B+1) /* 9 bytes */ u8 board_pba_number[9]; /* abs.ofs: 119 */ u8 reserved5[8]; -#define EEPROM_VERSION (2*0x44) /* 2 bytes */ u16 version; /* abs.ofs: 136 */ -#define EEPROM_SKU_CAP (2*0x45) /* 1 bytes */ u8 sku_cap; /* abs.ofs: 138 */ -#define EEPROM_LEDS_MODE (2*0x45+1) /* 1 bytes */ u8 leds_mode; /* abs.ofs: 139 */ -#define EEPROM_OEM_MODE (2*0x46) /* 2 bytes */ u16 oem_mode; -#define EEPROM_WOWLAN_MODE (2*0x47) /* 2 bytes */ u16 wowlan_mode; /* abs.ofs: 142 */ -#define EEPROM_LEDS_TIME_INTERVAL (2*0x48) /* 2 bytes */ u16 leds_time_interval; /* abs.ofs: 144 */ -#define EEPROM_LEDS_OFF_TIME (2*0x49) /* 1 bytes */ u8 leds_off_time; /* abs.ofs: 146 */ -#define EEPROM_LEDS_ON_TIME (2*0x49+1) /* 1 bytes */ u8 leds_on_time; /* abs.ofs: 147 */ -#define EEPROM_ALMGOR_M_VERSION (2*0x4A) /* 1 bytes */ u8 almgor_m_version; /* abs.ofs: 148 */ -#define EEPROM_ANTENNA_SWITCH_TYPE (2*0x4A+1) /* 1 bytes */ u8 antenna_switch_type; /* abs.ofs: 149 */ u8 reserved6[42]; -#define EEPROM_REGULATORY_SKU_ID (2*0x60) /* 4 bytes */ u8 sku_id[4]; /* abs.ofs: 192 */ /* @@ -249,9 +233,7 @@ struct iwl3945_eeprom { * * 2.4 GHz channels 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14 */ -#define EEPROM_REGULATORY_BAND_1 (2*0x62) /* 2 bytes */ u16 band_1_count; /* abs.ofs: 196 */ -#define EEPROM_REGULATORY_BAND_1_CHANNELS (2*0x63) /* 28 bytes */ struct iwl3945_eeprom_channel band_1_channels[14]; /* abs.ofs: 196 */ /* @@ -259,36 +241,28 @@ struct iwl3945_eeprom { * 5.0 GHz channels 7, 8, 11, 12, 16 * (4915-5080MHz) (none of these is ever supported) */ -#define EEPROM_REGULATORY_BAND_2 (2*0x71) /* 2 bytes */ u16 band_2_count; /* abs.ofs: 226 */ -#define EEPROM_REGULATORY_BAND_2_CHANNELS (2*0x72) /* 26 bytes */ struct iwl3945_eeprom_channel band_2_channels[13]; /* abs.ofs: 228 */ /* * 5.2 GHz channels 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64 * (5170-5320MHz) */ -#define EEPROM_REGULATORY_BAND_3 (2*0x7F) /* 2 bytes */ u16 band_3_count; /* abs.ofs: 254 */ -#define EEPROM_REGULATORY_BAND_3_CHANNELS (2*0x80) /* 24 bytes */ struct iwl3945_eeprom_channel band_3_channels[12]; /* abs.ofs: 256 */ /* * 5.5 GHz channels 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 * (5500-5700MHz) */ -#define EEPROM_REGULATORY_BAND_4 (2*0x8C) /* 2 bytes */ u16 band_4_count; /* abs.ofs: 280 */ -#define EEPROM_REGULATORY_BAND_4_CHANNELS (2*0x8D) /* 22 bytes */ struct iwl3945_eeprom_channel band_4_channels[11]; /* abs.ofs: 282 */ /* * 5.7 GHz channels 145, 149, 153, 157, 161, 165 * (5725-5825MHz) */ -#define EEPROM_REGULATORY_BAND_5 (2*0x98) /* 2 bytes */ u16 band_5_count; /* abs.ofs: 304 */ -#define EEPROM_REGULATORY_BAND_5_CHANNELS (2*0x99) /* 12 bytes */ struct iwl3945_eeprom_channel band_5_channels[6]; /* abs.ofs: 306 */ u8 reserved9[194]; @@ -296,15 +270,9 @@ struct iwl3945_eeprom { /* * 3945 Txpower calibration data. */ -#define EEPROM_TXPOWER_CALIB_GROUP0 0x200 -#define EEPROM_TXPOWER_CALIB_GROUP1 0x240 -#define EEPROM_TXPOWER_CALIB_GROUP2 0x280 -#define EEPROM_TXPOWER_CALIB_GROUP3 0x2c0 -#define EEPROM_TXPOWER_CALIB_GROUP4 0x300 #define IWL_NUM_TX_CALIB_GROUPS 5 struct iwl3945_eeprom_txpower_group groups[IWL_NUM_TX_CALIB_GROUPS]; /* abs.ofs: 512 */ -#define EEPROM_CALIB_TEMPERATURE_CORRECT 0x340 struct iwl3945_eeprom_temperature_corr corrections; /* abs.ofs: 832 */ u8 reserved16[172]; /* fill out to full 1024 byte block */ } __attribute__ ((packed)); @@ -321,181 +289,6 @@ struct iwl3945_eeprom { #define PCI_REG_WUM8 0x0E8 #define PCI_CFG_PMC_PME_FROM_D3COLD_SUPPORT (0x80000000) -/*=== CSR (control and status registers) ===*/ -#define CSR_BASE (0x000) - -#define CSR_SW_VER (CSR_BASE+0x000) -#define CSR_HW_IF_CONFIG_REG (CSR_BASE+0x000) /* hardware interface config */ -#define CSR_INT_COALESCING (CSR_BASE+0x004) /* accum ints, 32-usec units */ -#define CSR_INT (CSR_BASE+0x008) /* host interrupt status/ack */ -#define CSR_INT_MASK (CSR_BASE+0x00c) /* host interrupt enable */ -#define CSR_FH_INT_STATUS (CSR_BASE+0x010) /* busmaster int status/ack*/ -#define CSR_GPIO_IN (CSR_BASE+0x018) /* read external chip pins */ -#define CSR_RESET (CSR_BASE+0x020) /* busmaster enable, NMI, etc*/ -#define CSR_GP_CNTRL (CSR_BASE+0x024) - -/* - * Hardware revision info - * Bit fields: - * 31-8: Reserved - * 7-4: Type of device: 0x0 = 4965, 0xd = 3945 - * 3-2: Revision step: 0 = A, 1 = B, 2 = C, 3 = D - * 1-0: "Dash" value, as in A-1, etc. - */ -#define CSR_HW_REV (CSR_BASE+0x028) - -/* EEPROM reads */ -#define CSR_EEPROM_REG (CSR_BASE+0x02c) -#define CSR_EEPROM_GP (CSR_BASE+0x030) -#define CSR_GP_UCODE (CSR_BASE+0x044) -#define CSR_UCODE_DRV_GP1 (CSR_BASE+0x054) -#define CSR_UCODE_DRV_GP1_SET (CSR_BASE+0x058) -#define CSR_UCODE_DRV_GP1_CLR (CSR_BASE+0x05c) -#define CSR_UCODE_DRV_GP2 (CSR_BASE+0x060) -#define CSR_GIO_CHICKEN_BITS (CSR_BASE+0x100) - -/* Analog phase-lock-loop configuration (3945 only) - * Set bit 24. */ -#define CSR_ANA_PLL_CFG (CSR_BASE+0x20c) - -/* Bits for CSR_HW_IF_CONFIG_REG */ -#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MB (0x00000100) -#define CSR_HW_IF_CONFIG_REG_BIT_ALMAGOR_MM (0x00000200) -#define CSR_HW_IF_CONFIG_REG_BIT_SKU_MRC (0x00000400) -#define CSR_HW_IF_CONFIG_REG_BIT_BOARD_TYPE (0x00000800) -#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A (0x00000000) -#define CSR_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B (0x00001000) -#define CSR_HW_IF_CONFIG_REG_BIT_EEPROM_OWN_SEM (0x00200000) - -/* interrupt flags in INTA, set by uCode or hardware (e.g. dma), - * acknowledged (reset) by host writing "1" to flagged bits. */ -#define CSR_INT_BIT_FH_RX (1 << 31) /* Rx DMA, cmd responses, FH_INT[17:16] */ -#define CSR_INT_BIT_HW_ERR (1 << 29) /* DMA hardware error FH_INT[31] */ -#define CSR_INT_BIT_DNLD (1 << 28) /* uCode Download */ -#define CSR_INT_BIT_FH_TX (1 << 27) /* Tx DMA FH_INT[1:0] */ -#define CSR_INT_BIT_SCD (1 << 26) /* TXQ pointer advanced */ -#define CSR_INT_BIT_SW_ERR (1 << 25) /* uCode error */ -#define CSR_INT_BIT_RF_KILL (1 << 7) /* HW RFKILL switch GP_CNTRL[27] toggled */ -#define CSR_INT_BIT_CT_KILL (1 << 6) /* Critical temp (chip too hot) rfkill */ -#define CSR_INT_BIT_SW_RX (1 << 3) /* Rx, command responses, 3945 */ -#define CSR_INT_BIT_WAKEUP (1 << 1) /* NIC controller waking up (pwr mgmt) */ -#define CSR_INT_BIT_ALIVE (1 << 0) /* uCode interrupts once it initializes */ - -#define CSR_INI_SET_MASK (CSR_INT_BIT_FH_RX | \ - CSR_INT_BIT_HW_ERR | \ - CSR_INT_BIT_FH_TX | \ - CSR_INT_BIT_SW_ERR | \ - CSR_INT_BIT_RF_KILL | \ - CSR_INT_BIT_SW_RX | \ - CSR_INT_BIT_WAKEUP | \ - CSR_INT_BIT_ALIVE) - -/* interrupt flags in FH (flow handler) (PCI busmaster DMA) */ -#define CSR_FH_INT_BIT_ERR (1 << 31) /* Error */ -#define CSR_FH_INT_BIT_HI_PRIOR (1 << 30) /* High priority Rx, bypass coalescing */ -#define CSR_FH_INT_BIT_RX_CHNL2 (1 << 18) /* Rx channel 2 (3945 only) */ -#define CSR_FH_INT_BIT_RX_CHNL1 (1 << 17) /* Rx channel 1 */ -#define CSR_FH_INT_BIT_RX_CHNL0 (1 << 16) /* Rx channel 0 */ -#define CSR_FH_INT_BIT_TX_CHNL6 (1 << 6) /* Tx channel 6 (3945 only) */ -#define CSR_FH_INT_BIT_TX_CHNL1 (1 << 1) /* Tx channel 1 */ -#define CSR_FH_INT_BIT_TX_CHNL0 (1 << 0) /* Tx channel 0 */ - -#define CSR_FH_INT_RX_MASK (CSR_FH_INT_BIT_HI_PRIOR | \ - CSR_FH_INT_BIT_RX_CHNL2 | \ - CSR_FH_INT_BIT_RX_CHNL1 | \ - CSR_FH_INT_BIT_RX_CHNL0) - -#define CSR_FH_INT_TX_MASK (CSR_FH_INT_BIT_TX_CHNL6 | \ - CSR_FH_INT_BIT_TX_CHNL1 | \ - CSR_FH_INT_BIT_TX_CHNL0) - - -/* RESET */ -#define CSR_RESET_REG_FLAG_NEVO_RESET (0x00000001) -#define CSR_RESET_REG_FLAG_FORCE_NMI (0x00000002) -#define CSR_RESET_REG_FLAG_SW_RESET (0x00000080) -#define CSR_RESET_REG_FLAG_MASTER_DISABLED (0x00000100) -#define CSR_RESET_REG_FLAG_STOP_MASTER (0x00000200) - -/* GP (general purpose) CONTROL */ -#define CSR_GP_CNTRL_REG_FLAG_MAC_CLOCK_READY (0x00000001) -#define CSR_GP_CNTRL_REG_FLAG_INIT_DONE (0x00000004) -#define CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ (0x00000008) -#define CSR_GP_CNTRL_REG_FLAG_GOING_TO_SLEEP (0x00000010) - -#define CSR_GP_CNTRL_REG_VAL_MAC_ACCESS_EN (0x00000001) - -#define CSR_GP_CNTRL_REG_MSK_POWER_SAVE_TYPE (0x07000000) -#define CSR_GP_CNTRL_REG_FLAG_MAC_POWER_SAVE (0x04000000) -#define CSR_GP_CNTRL_REG_FLAG_HW_RF_KILL_SW (0x08000000) - - -/* EEPROM REG */ -#define CSR_EEPROM_REG_READ_VALID_MSK (0x00000001) -#define CSR_EEPROM_REG_BIT_CMD (0x00000002) - -/* EEPROM GP */ -#define CSR_EEPROM_GP_VALID_MSK (0x00000006) -#define CSR_EEPROM_GP_BAD_SIGNATURE (0x00000000) -#define CSR_EEPROM_GP_IF_OWNER_MSK (0x00000180) - -/* UCODE DRV GP */ -#define CSR_UCODE_DRV_GP1_BIT_MAC_SLEEP (0x00000001) -#define CSR_UCODE_SW_BIT_RFKILL (0x00000002) -#define CSR_UCODE_DRV_GP1_BIT_CMD_BLOCKED (0x00000004) -#define CSR_UCODE_DRV_GP1_REG_BIT_CT_KILL_EXIT (0x00000008) - -/* GPIO */ -#define CSR_GPIO_IN_BIT_AUX_POWER (0x00000200) -#define CSR_GPIO_IN_VAL_VAUX_PWR_SRC (0x00000000) -#define CSR_GPIO_IN_VAL_VMAIN_PWR_SRC CSR_GPIO_IN_BIT_AUX_POWER - -/* GI Chicken Bits */ -#define CSR_GIO_CHICKEN_BITS_REG_BIT_L1A_NO_L0S_RX (0x00800000) -#define CSR_GIO_CHICKEN_BITS_REG_BIT_DIS_L0S_EXIT_TIMER (0x20000000) - -/* CSR_ANA_PLL_CFG */ -#define CSR_ANA_PLL_CFG_SH (0x00880300) - -/*=== HBUS (Host-side Bus) ===*/ -#define HBUS_BASE (0x400) - -/* - * Registers for accessing device's internal SRAM memory (e.g. SCD SRAM - * structures, error log, event log, verifying uCode load). - * First write to address register, then read from or write to data register - * to complete the job. Once the address register is set up, accesses to - * data registers auto-increment the address by one dword. - * Bit usage for address registers (read or write): - * 0-31: memory address within device - */ -#define HBUS_TARG_MEM_RADDR (HBUS_BASE+0x00c) -#define HBUS_TARG_MEM_WADDR (HBUS_BASE+0x010) -#define HBUS_TARG_MEM_WDAT (HBUS_BASE+0x018) -#define HBUS_TARG_MEM_RDAT (HBUS_BASE+0x01c) - -/* - * Registers for accessing device's internal peripheral registers - * (e.g. SCD, BSM, etc.). First write to address register, - * then read from or write to data register to complete the job. - * Bit usage for address registers (read or write): - * 0-15: register address (offset) within device - * 24-25: (# bytes - 1) to read or write (e.g. 3 for dword) - */ -#define HBUS_TARG_PRPH_WADDR (HBUS_BASE+0x044) -#define HBUS_TARG_PRPH_RADDR (HBUS_BASE+0x048) -#define HBUS_TARG_PRPH_WDAT (HBUS_BASE+0x04c) -#define HBUS_TARG_PRPH_RDAT (HBUS_BASE+0x050) - -/* - * Per-Tx-queue write pointer (index, really!) (3945 and 4965). - * Indicates index to next TFD that driver will fill (1 past latest filled). - * Bit usage: - * 0-7: queue write index - * 11-8: queue selector - */ -#define HBUS_TARG_WRPTR (HBUS_BASE+0x060) - /* SCD (3945 Tx Frame Scheduler) */ #define SCD_BASE (CSR_BASE + 0x2E00) @@ -663,7 +456,7 @@ struct iwl3945_eeprom { /* Size of uCode instruction memory in bootstrap state machine */ #define IWL_MAX_BSM_SIZE ALM_RTC_INST_SIZE -#define IWL_MAX_NUM_QUEUES 8 +#define IWL39_MAX_NUM_QUEUES 8 static inline int iwl3945_hw_valid_rtc_data_addr(u32 addr) { |
