diff options
Diffstat (limited to 'drivers/gpu')
-rw-r--r-- | drivers/gpu/drm/i2c/adv7511.c | 48 | ||||
-rw-r--r-- | drivers/gpu/drm/i2c/adv7511.h | 12 | ||||
-rw-r--r-- | drivers/gpu/drm/i915/Kconfig | 1 | ||||
-rw-r--r-- | drivers/gpu/drm/i915/i915_drv.c | 4 | ||||
-rw-r--r-- | drivers/gpu/drm/i915/intel_display.c | 33 | ||||
-rw-r--r-- | drivers/gpu/drm/i915/intel_lrc.c | 1 | ||||
-rw-r--r-- | drivers/gpu/drm/i915/intel_ringbuffer.c | 2 |
7 files changed, 63 insertions, 38 deletions
diff --git a/drivers/gpu/drm/i2c/adv7511.c b/drivers/gpu/drm/i2c/adv7511.c index 533d1e3d4a99..a02112ba1c3d 100644 --- a/drivers/gpu/drm/i2c/adv7511.c +++ b/drivers/gpu/drm/i2c/adv7511.c @@ -136,6 +136,7 @@ static bool adv7511_register_volatile(struct device *dev, unsigned int reg) case ADV7511_REG_BKSV(3): case ADV7511_REG_BKSV(4): case ADV7511_REG_DDC_STATUS: + case ADV7511_REG_EDID_READ_CTRL: case ADV7511_REG_BSTATUS(0): case ADV7511_REG_BSTATUS(1): case ADV7511_REG_CHIP_ID_HIGH: @@ -362,24 +363,31 @@ static void adv7511_power_on(struct adv7511 *adv7511) { adv7511->current_edid_segment = -1; - regmap_write(adv7511->regmap, ADV7511_REG_INT(0), - ADV7511_INT0_EDID_READY); - regmap_write(adv7511->regmap, ADV7511_REG_INT(1), - ADV7511_INT1_DDC_ERROR); regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, ADV7511_POWER_POWER_DOWN, 0); + if (adv7511->i2c_main->irq) { + /* + * Documentation says the INT_ENABLE registers are reset in + * POWER_DOWN mode. My 7511w preserved the bits, however. + * Still, let's be safe and stick to the documentation. + */ + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0), + ADV7511_INT0_EDID_READY); + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1), + ADV7511_INT1_DDC_ERROR); + } /* - * Per spec it is allowed to pulse the HDP signal to indicate that the + * Per spec it is allowed to pulse the HPD signal to indicate that the * EDID information has changed. Some monitors do this when they wakeup - * from standby or are enabled. When the HDP goes low the adv7511 is + * from standby or are enabled. When the HPD goes low the adv7511 is * reset and the outputs are disabled which might cause the monitor to - * go to standby again. To avoid this we ignore the HDP pin for the + * go to standby again. To avoid this we ignore the HPD pin for the * first few seconds after enabling the output. */ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, - ADV7511_REG_POWER2_HDP_SRC_MASK, - ADV7511_REG_POWER2_HDP_SRC_NONE); + ADV7511_REG_POWER2_HPD_SRC_MASK, + ADV7511_REG_POWER2_HPD_SRC_NONE); /* * Most of the registers are reset during power down or when HPD is low. @@ -413,9 +421,9 @@ static bool adv7511_hpd(struct adv7511 *adv7511) if (ret < 0) return false; - if (irq0 & ADV7511_INT0_HDP) { + if (irq0 & ADV7511_INT0_HPD) { regmap_write(adv7511->regmap, ADV7511_REG_INT(0), - ADV7511_INT0_HDP); + ADV7511_INT0_HPD); return true; } @@ -438,7 +446,7 @@ static int adv7511_irq_process(struct adv7511 *adv7511) regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0); regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1); - if (irq0 & ADV7511_INT0_HDP && adv7511->encoder) + if (irq0 & ADV7511_INT0_HPD && adv7511->encoder) drm_helper_hpd_irq_event(adv7511->encoder->dev); if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) { @@ -567,12 +575,14 @@ static int adv7511_get_modes(struct drm_encoder *encoder, /* Reading the EDID only works if the device is powered */ if (!adv7511->powered) { - regmap_write(adv7511->regmap, ADV7511_REG_INT(0), - ADV7511_INT0_EDID_READY); - regmap_write(adv7511->regmap, ADV7511_REG_INT(1), - ADV7511_INT1_DDC_ERROR); regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER, ADV7511_POWER_POWER_DOWN, 0); + if (adv7511->i2c_main->irq) { + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0), + ADV7511_INT0_EDID_READY); + regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(1), + ADV7511_INT1_DDC_ERROR); + } adv7511->current_edid_segment = -1; } @@ -638,10 +648,10 @@ adv7511_encoder_detect(struct drm_encoder *encoder, if (adv7511->status == connector_status_connected) status = connector_status_disconnected; } else { - /* Renable HDP sensing */ + /* Renable HPD sensing */ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2, - ADV7511_REG_POWER2_HDP_SRC_MASK, - ADV7511_REG_POWER2_HDP_SRC_BOTH); + ADV7511_REG_POWER2_HPD_SRC_MASK, + ADV7511_REG_POWER2_HPD_SRC_BOTH); } adv7511->status = status; diff --git a/drivers/gpu/drm/i2c/adv7511.h b/drivers/gpu/drm/i2c/adv7511.h index 6599ed538426..38515b30cedf 100644 --- a/drivers/gpu/drm/i2c/adv7511.h +++ b/drivers/gpu/drm/i2c/adv7511.h @@ -90,7 +90,7 @@ #define ADV7511_CSC_ENABLE BIT(7) #define ADV7511_CSC_UPDATE_MODE BIT(5) -#define ADV7511_INT0_HDP BIT(7) +#define ADV7511_INT0_HPD BIT(7) #define ADV7511_INT0_VSYNC BIT(5) #define ADV7511_INT0_AUDIO_FIFO_FULL BIT(4) #define ADV7511_INT0_EDID_READY BIT(2) @@ -157,11 +157,11 @@ #define ADV7511_PACKET_ENABLE_SPARE2 BIT(1) #define ADV7511_PACKET_ENABLE_SPARE1 BIT(0) -#define ADV7511_REG_POWER2_HDP_SRC_MASK 0xc0 -#define ADV7511_REG_POWER2_HDP_SRC_BOTH 0x00 -#define ADV7511_REG_POWER2_HDP_SRC_HDP 0x40 -#define ADV7511_REG_POWER2_HDP_SRC_CEC 0x80 -#define ADV7511_REG_POWER2_HDP_SRC_NONE 0xc0 +#define ADV7511_REG_POWER2_HPD_SRC_MASK 0xc0 +#define ADV7511_REG_POWER2_HPD_SRC_BOTH 0x00 +#define ADV7511_REG_POWER2_HPD_SRC_HPD 0x40 +#define ADV7511_REG_POWER2_HPD_SRC_CEC 0x80 +#define ADV7511_REG_POWER2_HPD_SRC_NONE 0xc0 #define ADV7511_REG_POWER2_TDMS_ENABLE BIT(4) #define ADV7511_REG_POWER2_GATE_INPUT_CLK BIT(0) diff --git a/drivers/gpu/drm/i915/Kconfig b/drivers/gpu/drm/i915/Kconfig index fcd77b27514d..051eab33e4c7 100644 --- a/drivers/gpu/drm/i915/Kconfig +++ b/drivers/gpu/drm/i915/Kconfig @@ -10,7 +10,6 @@ config DRM_I915 # the shmem_readpage() which depends upon tmpfs select SHMEM select TMPFS - select STOP_MACHINE select DRM_KMS_HELPER select DRM_PANEL select DRM_MIPI_DSI diff --git a/drivers/gpu/drm/i915/i915_drv.c b/drivers/gpu/drm/i915/i915_drv.c index 3ac616d7363b..f357058c74d9 100644 --- a/drivers/gpu/drm/i915/i915_drv.c +++ b/drivers/gpu/drm/i915/i915_drv.c @@ -501,7 +501,9 @@ void intel_detect_pch(struct drm_device *dev) WARN_ON(!IS_SKYLAKE(dev) && !IS_KABYLAKE(dev)); } else if ((id == INTEL_PCH_P2X_DEVICE_ID_TYPE) || - (id == INTEL_PCH_QEMU_DEVICE_ID_TYPE)) { + ((id == INTEL_PCH_QEMU_DEVICE_ID_TYPE) && + pch->subsystem_vendor == 0x1af4 && + pch->subsystem_device == 0x1100)) { dev_priv->pch_type = intel_virt_detect_pch(dev); } else continue; diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c index 2f00828ccc6e..5feb65725c04 100644 --- a/drivers/gpu/drm/i915/intel_display.c +++ b/drivers/gpu/drm/i915/intel_display.c @@ -2946,7 +2946,7 @@ u32 intel_plane_obj_offset(struct intel_plane *intel_plane, struct i915_vma *vma; u64 offset; - intel_fill_fb_ggtt_view(&view, intel_plane->base.fb, + intel_fill_fb_ggtt_view(&view, intel_plane->base.state->fb, intel_plane->base.state); vma = i915_gem_obj_to_ggtt_view(obj, &view); @@ -12075,11 +12075,21 @@ connected_sink_compute_bpp(struct intel_connector *connector, pipe_config->pipe_bpp = connector->base.display_info.bpc*3; } - /* Clamp bpp to 8 on screens without EDID 1.4 */ - if (connector->base.display_info.bpc == 0 && bpp > 24) { - DRM_DEBUG_KMS("clamping display bpp (was %d) to default limit of 24\n", - bpp); - pipe_config->pipe_bpp = 24; + /* Clamp bpp to default limit on screens without EDID 1.4 */ + if (connector->base.display_info.bpc == 0) { + int type = connector->base.connector_type; + int clamp_bpp = 24; + + /* Fall back to 18 bpp when DP sink capability is unknown. */ + if (type == DRM_MODE_CONNECTOR_DisplayPort || + type == DRM_MODE_CONNECTOR_eDP) + clamp_bpp = 18; + + if (bpp > clamp_bpp) { + DRM_DEBUG_KMS("clamping display bpp (was %d) to default limit of %d\n", + bpp, clamp_bpp); + pipe_config->pipe_bpp = clamp_bpp; + } } } @@ -13883,11 +13893,12 @@ intel_check_primary_plane(struct drm_plane *plane, int max_scale = DRM_PLANE_HELPER_NO_SCALING; bool can_position = false; - /* use scaler when colorkey is not required */ - if (INTEL_INFO(plane->dev)->gen >= 9 && - state->ckey.flags == I915_SET_COLORKEY_NONE) { - min_scale = 1; - max_scale = skl_max_scale(to_intel_crtc(crtc), crtc_state); + if (INTEL_INFO(plane->dev)->gen >= 9) { + /* use scaler when colorkey is not required */ + if (state->ckey.flags == I915_SET_COLORKEY_NONE) { + min_scale = 1; + max_scale = skl_max_scale(to_intel_crtc(crtc), crtc_state); + } can_position = true; } diff --git a/drivers/gpu/drm/i915/intel_lrc.c b/drivers/gpu/drm/i915/intel_lrc.c index 3aa614731d7e..f1fa756c5d5d 100644 --- a/drivers/gpu/drm/i915/intel_lrc.c +++ b/drivers/gpu/drm/i915/intel_lrc.c @@ -1707,6 +1707,7 @@ static int gen8_emit_flush_render(struct drm_i915_gem_request *request, if (flush_domains) { flags |= PIPE_CONTROL_RENDER_TARGET_CACHE_FLUSH; flags |= PIPE_CONTROL_DEPTH_CACHE_FLUSH; + flags |= PIPE_CONTROL_DC_FLUSH_ENABLE; flags |= PIPE_CONTROL_FLUSH_ENABLE; } diff --git a/drivers/gpu/drm/i915/intel_ringbuffer.c b/drivers/gpu/drm/i915/intel_ringbuffer.c index 339701d7a9a5..40c6aff57256 100644 --- a/drivers/gpu/drm/i915/intel_ringbuffer.c +++ b/drivers/gpu/drm/i915/intel_ringbuffer.c @@ -331,6 +331,7 @@ gen7_render_ring_flush(struct drm_i915_gem_request *req, if (flush_domains) { flags |= PIPE_CONTROL_RENDER_TARGET_CACHE_FLUSH; flags |= PIPE_CONTROL_DEPTH_CACHE_FLUSH; + flags |= PIPE_CONTROL_DC_FLUSH_ENABLE; flags |= PIPE_CONTROL_FLUSH_ENABLE; } if (invalidate_domains) { @@ -403,6 +404,7 @@ gen8_render_ring_flush(struct drm_i915_gem_request *req, if (flush_domains) { flags |= PIPE_CONTROL_RENDER_TARGET_CACHE_FLUSH; flags |= PIPE_CONTROL_DEPTH_CACHE_FLUSH; + flags |= PIPE_CONTROL_DC_FLUSH_ENABLE; flags |= PIPE_CONTROL_FLUSH_ENABLE; } if (invalidate_domains) { |