8 files changed, 454 insertions, 11 deletions

diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
index ff6cb9e4c381..de3eaf051697 100644
--- a/drivers/ata/Kconfig
+++ b/drivers/ata/Kconfig
@@ -518,6 +518,15 @@ config PATA_BF54X
 
 	  If unsure, say N.
 
+config PATA_BK3710
+	tristate "Palmchip BK3710 PATA support"
+	depends on ARCH_DAVINCI
+	help
+	  This option enables support for the integrated IDE controller on
+	  the TI DaVinci SoC.
+
+	  If unsure, say N.
+
 config PATA_CMD64X
 	tristate "CMD64x PATA support"
 	depends on PCI
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index 3048cc100a46..cd931a5eba92 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -51,6 +51,7 @@ obj-$(CONFIG_PATA_ARTOP)	+= pata_artop.o
 obj-$(CONFIG_PATA_ATIIXP)	+= pata_atiixp.o
 obj-$(CONFIG_PATA_ATP867X)	+= pata_atp867x.o
 obj-$(CONFIG_PATA_BF54X)	+= pata_bf54x.o
+obj-$(CONFIG_PATA_BK3710)	+= pata_bk3710.o
 obj-$(CONFIG_PATA_CMD64X)	+= pata_cmd64x.o
 obj-$(CONFIG_PATA_CS5520)	+= pata_cs5520.o
 obj-$(CONFIG_PATA_CS5530)	+= pata_cs5530.o
diff --git a/drivers/ata/ahci.c b/drivers/ata/ahci.c
index 2fc52407306c..c69954023c2e 100644
--- a/drivers/ata/ahci.c
+++ b/drivers/ata/ahci.c
@@ -1364,6 +1364,40 @@ static inline void ahci_gtf_filter_workaround(struct ata_host *host)
 {}
 #endif
 
+/*
+ * On the Acer Aspire Switch Alpha 12, sometimes all SATA ports are detected
+ * as DUMMY, or detected but eventually get a "link down" and never get up
+ * again. When this happens, CAP.NP may hold a value of 0x00 or 0x01, and the
+ * port_map may hold a value of 0x00.
+ *
+ * Overriding CAP.NP to 0x02 and the port_map to 0x7 will reveal all 3 ports
+ * and can significantly reduce the occurrence of the problem.
+ *
+ * https://bugzilla.kernel.org/show_bug.cgi?id=189471
+ */
+static void acer_sa5_271_workaround(struct ahci_host_priv *hpriv,
+				    struct pci_dev *pdev)
+{
+	static const struct dmi_system_id sysids[] = {
+		{
+			.ident = "Acer Switch Alpha 12",
+			.matches = {
+				DMI_MATCH(DMI_SYS_VENDOR, "Acer"),
+				DMI_MATCH(DMI_PRODUCT_NAME, "Switch SA5-271")
+			},
+		},
+		{ }
+	};
+
+	if (dmi_check_system(sysids)) {
+		dev_info(&pdev->dev, "enabling Acer Switch Alpha 12 workaround\n");
+		if ((hpriv->saved_cap & 0xC734FF00) == 0xC734FF00) {
+			hpriv->port_map = 0x7;
+			hpriv->cap = 0xC734FF02;
+		}
+	}
+}
+
 #ifdef CONFIG_ARM64
 /*
  * Due to ERRATA#22536, ThunderX needs to handle HOST_IRQ_STAT differently.
@@ -1636,6 +1670,10 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 			 "online status unreliable, applying workaround\n");
 	}
 
+
+	/* Acer SA5-271 workaround modifies private_data */
+	acer_sa5_271_workaround(hpriv, pdev);
+
 	/* CAP.NP sometimes indicate the index of the last enabled
 	 * port, at other times, that of the last possible port, so
 	 * determining the maximum port number requires looking at
diff --git a/drivers/ata/libahci_platform.c b/drivers/ata/libahci_platform.c
index aaa761b9081c..cd2eab6aa92e 100644
--- a/drivers/ata/libahci_platform.c
+++ b/drivers/ata/libahci_platform.c
@@ -514,8 +514,9 @@ int ahci_platform_init_host(struct platform_device *pdev,
 
 	irq = platform_get_irq(pdev, 0);
 	if (irq <= 0) {
-		dev_err(dev, "no irq\n");
-		return -EINVAL;
+		if (irq != -EPROBE_DEFER)
+			dev_err(dev, "no irq\n");
+		return irq;
 	}
 
 	hpriv->irq = irq;
diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c
index 2d83b8c75965..e157a0e44419 100644
--- a/drivers/ata/libata-core.c
+++ b/drivers/ata/libata-core.c
@@ -6800,7 +6800,7 @@ static int __init ata_parse_force_one(char **cur,
 	}
 
 	force_ent->port = simple_strtoul(id, &endp, 10);
-	if (p == endp || *endp != '\0') {
+	if (id == endp || *endp != '\0') {
 		*reason = "invalid port/link";
 		return -EINVAL;
 	}
diff --git a/drivers/ata/pata_bk3710.c b/drivers/ata/pata_bk3710.c
new file mode 100644
index 000000000000..6c3bd5fae3e4
--- /dev/null
+++ b/drivers/ata/pata_bk3710.c
@@ -0,0 +1,382 @@
+/*
+ * Palmchip BK3710 PATA controller driver
+ *
+ * Copyright (c) 2017 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ *
+ * Based on palm_bk3710.c:
+ *
+ * Copyright (C) 2006 Texas Instruments.
+ * Copyright (C) 2007 MontaVista Software, Inc., <source@mvista.com>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/ata.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/init.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/libata.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+
+#define DRV_NAME "pata_bk3710"
+
+#define BK3710_TF_OFFSET	0x1F0
+#define BK3710_CTL_OFFSET	0x3F6
+
+#define BK3710_BMISP		0x02
+#define BK3710_IDETIMP		0x40
+#define BK3710_UDMACTL		0x48
+#define BK3710_MISCCTL		0x50
+#define BK3710_REGSTB		0x54
+#define BK3710_REGRCVR		0x58
+#define BK3710_DATSTB		0x5C
+#define BK3710_DATRCVR		0x60
+#define BK3710_DMASTB		0x64
+#define BK3710_DMARCVR		0x68
+#define BK3710_UDMASTB		0x6C
+#define BK3710_UDMATRP		0x70
+#define BK3710_UDMAENV		0x74
+#define BK3710_IORDYTMP		0x78
+
+static struct scsi_host_template pata_bk3710_sht = {
+	ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static unsigned int ideclk_period; /* in nanoseconds */
+
+struct pata_bk3710_udmatiming {
+	unsigned int rptime;	/* tRP -- Ready to pause time (nsec) */
+	unsigned int cycletime;	/* tCYCTYP2/2 -- avg Cycle Time (nsec) */
+				/* tENV is always a minimum of 20 nsec */
+};
+
+static const struct pata_bk3710_udmatiming pata_bk3710_udmatimings[6] = {
+	{ 160, 240 / 2 },	/* UDMA Mode 0 */
+	{ 125, 160 / 2 },	/* UDMA Mode 1 */
+	{ 100, 120 / 2 },	/* UDMA Mode 2 */
+	{ 100,  90 / 2 },	/* UDMA Mode 3 */
+	{ 100,  60 / 2 },	/* UDMA Mode 4 */
+	{  85,  40 / 2 },	/* UDMA Mode 5 */
+};
+
+static void pata_bk3710_setudmamode(void __iomem *base, unsigned int dev,
+				    unsigned int mode)
+{
+	u32 val32;
+	u16 val16;
+	u8 tenv, trp, t0;
+
+	/* DMA Data Setup */
+	t0 = DIV_ROUND_UP(pata_bk3710_udmatimings[mode].cycletime,
+			  ideclk_period) - 1;
+	tenv = DIV_ROUND_UP(20, ideclk_period) - 1;
+	trp = DIV_ROUND_UP(pata_bk3710_udmatimings[mode].rptime,
+			   ideclk_period) - 1;
+
+	/* udmastb Ultra DMA Access Strobe Width */
+	val32 = ioread32(base + BK3710_UDMASTB) & (0xFF << (dev ? 0 : 8));
+	val32 |= t0 << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_UDMASTB);
+
+	/* udmatrp Ultra DMA Ready to Pause Time */
+	val32 = ioread32(base + BK3710_UDMATRP) & (0xFF << (dev ? 0 : 8));
+	val32 |= trp << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_UDMATRP);
+
+	/* udmaenv Ultra DMA envelop Time */
+	val32 = ioread32(base + BK3710_UDMAENV) & (0xFF << (dev ? 0 : 8));
+	val32 |= tenv << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_UDMAENV);
+
+	/* Enable UDMA for Device */
+	val16 = ioread16(base + BK3710_UDMACTL) | (1 << dev);
+	iowrite16(val16, base + BK3710_UDMACTL);
+}
+
+static void pata_bk3710_setmwdmamode(void __iomem *base, unsigned int dev,
+				     unsigned short min_cycle,
+				     unsigned int mode)
+{
+	const struct ata_timing *t;
+	int cycletime;
+	u32 val32;
+	u16 val16;
+	u8 td, tkw, t0;
+
+	t = ata_timing_find_mode(mode);
+	cycletime = max_t(int, t->cycle, min_cycle);
+
+	/* DMA Data Setup */
+	t0 = DIV_ROUND_UP(cycletime, ideclk_period);
+	td = DIV_ROUND_UP(t->active, ideclk_period);
+	tkw = t0 - td - 1;
+	td--;
+
+	val32 = ioread32(base + BK3710_DMASTB) & (0xFF << (dev ? 0 : 8));
+	val32 |= td << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_DMASTB);
+
+	val32 = ioread32(base + BK3710_DMARCVR) & (0xFF << (dev ? 0 : 8));
+	val32 |= tkw << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_DMARCVR);
+
+	/* Disable UDMA for Device */
+	val16 = ioread16(base + BK3710_UDMACTL) & ~(1 << dev);
+	iowrite16(val16, base + BK3710_UDMACTL);
+}
+
+static void pata_bk3710_set_dmamode(struct ata_port *ap,
+				    struct ata_device *adev)
+{
+	void __iomem *base = (void __iomem *)ap->ioaddr.bmdma_addr;
+	int is_slave = adev->devno;
+	const u8 xferspeed = adev->dma_mode;
+
+	if (xferspeed >= XFER_UDMA_0)
+		pata_bk3710_setudmamode(base, is_slave,
+					xferspeed - XFER_UDMA_0);
+	else
+		pata_bk3710_setmwdmamode(base, is_slave,
+					 adev->id[ATA_ID_EIDE_DMA_MIN],
+					 xferspeed);
+}
+
+static void pata_bk3710_setpiomode(void __iomem *base, struct ata_device *pair,
+				   unsigned int dev, unsigned int cycletime,
+				   unsigned int mode)
+{
+	const struct ata_timing *t;
+	u32 val32;
+	u8 t2, t2i, t0;
+
+	t = ata_timing_find_mode(XFER_PIO_0 + mode);
+
+	/* PIO Data Setup */
+	t0 = DIV_ROUND_UP(cycletime, ideclk_period);
+	t2 = DIV_ROUND_UP(t->active, ideclk_period);
+
+	t2i = t0 - t2 - 1;
+	t2--;
+
+	val32 = ioread32(base + BK3710_DATSTB) & (0xFF << (dev ? 0 : 8));
+	val32 |= t2 << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_DATSTB);
+
+	val32 = ioread32(base + BK3710_DATRCVR) & (0xFF << (dev ? 0 : 8));
+	val32 |= t2i << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_DATRCVR);
+
+	/* FIXME: this is broken also in the old driver */
+	if (pair) {
+		u8 mode2 = pair->pio_mode - XFER_PIO_0;
+
+		if (mode2 < mode)
+			mode = mode2;
+	}
+
+	/* TASKFILE Setup */
+	t0 = DIV_ROUND_UP(t->cyc8b, ideclk_period);
+	t2 = DIV_ROUND_UP(t->act8b, ideclk_period);
+
+	t2i = t0 - t2 - 1;
+	t2--;
+
+	val32 = ioread32(base + BK3710_REGSTB) & (0xFF << (dev ? 0 : 8));
+	val32 |= t2 << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_REGSTB);
+
+	val32 = ioread32(base + BK3710_REGRCVR) & (0xFF << (dev ? 0 : 8));
+	val32 |= t2i << (dev ? 8 : 0);
+	iowrite32(val32, base + BK3710_REGRCVR);
+}
+
+static void pata_bk3710_set_piomode(struct ata_port *ap,
+				    struct ata_device *adev)
+{
+	void __iomem *base = (void __iomem *)ap->ioaddr.bmdma_addr;
+	struct ata_device *pair = ata_dev_pair(adev);
+	const struct ata_timing *t = ata_timing_find_mode(adev->pio_mode);
+	const u16 *id = adev->id;
+	unsigned int cycle_time = 0;
+	int is_slave = adev->devno;
+	const u8 pio = adev->pio_mode - XFER_PIO_0;
+
+	if (id[ATA_ID_FIELD_VALID] & 2) {
+		if (ata_id_has_iordy(id))
+			cycle_time = id[ATA_ID_EIDE_PIO_IORDY];
+		else
+			cycle_time = id[ATA_ID_EIDE_PIO];
+
+		/* conservative "downgrade" for all pre-ATA2 drives */
+		if (pio < 3 && cycle_time < t->cycle)
+			cycle_time = 0; /* use standard timing */
+	}
+
+	if (!cycle_time)
+		cycle_time = t->cycle;
+
+	pata_bk3710_setpiomode(base, pair, is_slave, cycle_time, pio);
+}
+
+static void pata_bk3710_chipinit(void __iomem *base)
+{
+	/*
+	 * REVISIT:  the ATA reset signal needs to be managed through a
+	 * GPIO, which means it should come from platform_data.  Until
+	 * we get and use such information, we have to trust that things
+	 * have been reset before we get here.
+	 */
+
+	/*
+	 * Program the IDETIMP Register Value based on the following assumptions
+	 *
+	 * (ATA_IDETIMP_IDEEN		, ENABLE ) |
+	 * (ATA_IDETIMP_PREPOST1	, DISABLE) |
+	 * (ATA_IDETIMP_PREPOST0	, DISABLE) |
+	 *
+	 * DM6446 silicon rev 2.1 and earlier have no observed net benefit
+	 * from enabling prefetch/postwrite.
+	 */
+	iowrite16(BIT(15), base + BK3710_IDETIMP);
+
+	/*
+	 * UDMACTL Ultra-ATA DMA Control
+	 * (ATA_UDMACTL_UDMAP1	, 0 ) |
+	 * (ATA_UDMACTL_UDMAP0	, 0 )
+	 *
+	 */
+	iowrite16(0, base + BK3710_UDMACTL);
+
+	/*
+	 * MISCCTL Miscellaneous Conrol Register
+	 * (ATA_MISCCTL_HWNHLD1P	, 1 cycle)
+	 * (ATA_MISCCTL_HWNHLD0P	, 1 cycle)
+	 * (ATA_MISCCTL_TIMORIDE	, 1)
+	 */
+	iowrite32(0x001, base + BK3710_MISCCTL);
+
+	/*
+	 * IORDYTMP IORDY Timer for Primary Register
+	 * (ATA_IORDYTMP_IORDYTMP	, DISABLE)
+	 */
+	iowrite32(0, base + BK3710_IORDYTMP);
+
+	/*
+	 * Configure BMISP Register
+	 * (ATA_BMISP_DMAEN1	, DISABLE )	|
+	 * (ATA_BMISP_DMAEN0	, DISABLE )	|
+	 * (ATA_BMISP_IORDYINT	, CLEAR)	|
+	 * (ATA_BMISP_INTRSTAT	, CLEAR)	|
+	 * (ATA_BMISP_DMAERROR	, CLEAR)
+	 */
+	iowrite16(0xE, base + BK3710_BMISP);
+
+	pata_bk3710_setpiomode(base, NULL, 0, 600, 0);
+	pata_bk3710_setpiomode(base, NULL, 1, 600, 0);
+}
+
+static struct ata_port_operations pata_bk3710_ports_ops = {
+	.inherits		= &ata_bmdma_port_ops,
+	.cable_detect		= ata_cable_80wire,
+
+	.set_piomode		= pata_bk3710_set_piomode,
+	.set_dmamode		= pata_bk3710_set_dmamode,
+};
+
+static int __init pata_bk3710_probe(struct platform_device *pdev)
+{
+	struct clk *clk;
+	struct resource *mem;
+	struct ata_host *host;
+	struct ata_port *ap;
+	void __iomem *base;
+	unsigned long rate;
+	int irq;
+
+	clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		return -ENODEV;
+
+	clk_enable(clk);
+	rate = clk_get_rate(clk);
+	if (!rate)
+		return -EINVAL;
+
+	/* NOTE:  round *down* to meet minimum timings; we count in clocks */
+	ideclk_period = 1000000000UL / rate;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		pr_err(DRV_NAME ": failed to get IRQ resource\n");
+		return irq;
+	}
+
+	base = devm_ioremap_resource(&pdev->dev, mem);
+	if (IS_ERR(base))
+		return PTR_ERR(base);
+
+	/* configure the Palmchip controller */
+	pata_bk3710_chipinit(base);
+
+	/* allocate host */
+	host = ata_host_alloc(&pdev->dev, 1);
+	if (!host)
+		return -ENOMEM;
+	ap = host->ports[0];
+
+	ap->ops = &pata_bk3710_ports_ops;
+	ap->pio_mask = ATA_PIO4;
+	ap->mwdma_mask = ATA_MWDMA2;
+	ap->udma_mask = rate < 100000000 ? ATA_UDMA4 : ATA_UDMA5;
+	ap->flags |= ATA_FLAG_SLAVE_POSS;
+
+	ap->ioaddr.data_addr		= base + BK3710_TF_OFFSET;
+	ap->ioaddr.error_addr		= base + BK3710_TF_OFFSET + 1;
+	ap->ioaddr.feature_addr		= base + BK3710_TF_OFFSET + 1;
+	ap->ioaddr.nsect_addr		= base + BK3710_TF_OFFSET + 2;
+	ap->ioaddr.lbal_addr		= base + BK3710_TF_OFFSET + 3;
+	ap->ioaddr.lbam_addr		= base + BK3710_TF_OFFSET + 4;
+	ap->ioaddr.lbah_addr		= base + BK3710_TF_OFFSET + 5;
+	ap->ioaddr.device_addr		= base + BK3710_TF_OFFSET + 6;
+	ap->ioaddr.status_addr		= base + BK3710_TF_OFFSET + 7;
+	ap->ioaddr.command_addr		= base + BK3710_TF_OFFSET + 7;
+
+	ap->ioaddr.altstatus_addr	= base + BK3710_CTL_OFFSET;
+	ap->ioaddr.ctl_addr		= base + BK3710_CTL_OFFSET;
+
+	ap->ioaddr.bmdma_addr		= base;
+
+	ata_port_desc(ap, "cmd 0x%lx ctl 0x%lx",
+		      (unsigned long)base + BK3710_TF_OFFSET,
+		      (unsigned long)base + BK3710_CTL_OFFSET);
+
+	/* activate */
+	return ata_host_activate(host, irq, ata_sff_interrupt, 0,
+				 &pata_bk3710_sht);
+}
+
+/* work with hotplug and coldplug */
+MODULE_ALIAS("platform:palm_bk3710");
+
+static struct platform_driver pata_bk3710_driver = {
+	.driver = {
+		.name = "palm_bk3710",
+	},
+};
+
+static int __init pata_bk3710_init(void)
+{
+	return platform_driver_probe(&pata_bk3710_driver, pata_bk3710_probe);
+}
+
+module_init(pata_bk3710_init);
+MODULE_LICENSE("GPL");
diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c
index b66bcda88320..3b2246dded74 100644
--- a/drivers/ata/sata_mv.c
+++ b/drivers/ata/sata_mv.c
@@ -4067,7 +4067,6 @@ static int mv_platform_probe(struct platform_device *pdev)
 	struct ata_host *host;
 	struct mv_host_priv *hpriv;
 	struct resource *res;
-	void __iomem *mmio;
 	int n_ports = 0, irq = 0;
 	int rc;
 	int port;
@@ -4086,9 +4085,8 @@ static int mv_platform_probe(struct platform_device *pdev)
 	 * Get the register base first
 	 */
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	mmio = devm_ioremap_resource(&pdev->dev, res);
-	if (IS_ERR(mmio))
-		return PTR_ERR(mmio);
+	if (res == NULL)
+		return -EINVAL;
 
 	/* allocate host */
 	if (pdev->dev.of_node) {
@@ -4132,7 +4130,12 @@ static int mv_platform_probe(struct platform_device *pdev)
 	hpriv->board_idx = chip_soc;
 
 	host->iomap = NULL;
-	hpriv->base = mmio - SATAHC0_REG_BASE;
+	hpriv->base = devm_ioremap(&pdev->dev, res->start,
+				   resource_size(res));
+	if (!hpriv->base)
+		return -ENOMEM;
+
+	hpriv->base -= SATAHC0_REG_BASE;
 
 	hpriv->clk = clk_get(&pdev->dev, NULL);
 	if (IS_ERR(hpriv->clk))
diff --git a/drivers/ata/sata_rcar.c b/drivers/ata/sata_rcar.c
index 5d38245a7a73..b7939a2c1fab 100644
--- a/drivers/ata/sata_rcar.c
+++ b/drivers/ata/sata_rcar.c
@@ -890,7 +890,10 @@ static int sata_rcar_probe(struct platform_device *pdev)
 		dev_err(&pdev->dev, "failed to get access to sata clock\n");
 		return PTR_ERR(priv->clk);
 	}
-	clk_prepare_enable(priv->clk);
+
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
 
 	host = ata_host_alloc(&pdev->dev, 1);
 	if (!host) {
@@ -970,8 +973,11 @@ static int sata_rcar_resume(struct device *dev)
 	struct ata_host *host = dev_get_drvdata(dev);
 	struct sata_rcar_priv *priv = host->private_data;
 	void __iomem *base = priv->base;
+	int ret;
 
-	clk_prepare_enable(priv->clk);
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
 
 	/* ack and mask */
 	iowrite32(0, base + SATAINTSTAT_REG);
@@ -988,8 +994,11 @@ static int sata_rcar_restore(struct device *dev)
 {
 	struct ata_host *host = dev_get_drvdata(dev);
 	struct sata_rcar_priv *priv = host->private_data;
+	int ret;
 
-	clk_prepare_enable(priv->clk);
+	ret = clk_prepare_enable(priv->clk);
+	if (ret)
+		return ret;
 
 	sata_rcar_setup_port(host);