diff options
Diffstat (limited to 'arch/cris/arch-v10')
35 files changed, 2756 insertions, 2221 deletions
diff --git a/arch/cris/arch-v10/Kconfig b/arch/cris/arch-v10/Kconfig index 1d61faec77cd..adc164e99339 100644 --- a/arch/cris/arch-v10/Kconfig +++ b/arch/cris/arch-v10/Kconfig @@ -1,5 +1,7 @@ if ETRAX_ARCH_V10 +menu "CRIS v10 options" + # ETRAX 100LX v1 has a MMU "feature" requiring a low mapping config CRIS_LOW_MAP bool @@ -228,69 +230,6 @@ config ETRAX_LED12R For products with only one or two controllable LEDs, set this to same as CONFIG_ETRAX_LED1G (normally 2). -choice - prompt "Product debug-port" - depends on ETRAX_ARCH_V10 - default ETRAX_DEBUG_PORT0 - -config ETRAX_DEBUG_PORT0 - bool "Serial-0" - help - Choose a serial port for the ETRAX debug console. Default to - port 0. - -config ETRAX_DEBUG_PORT1 - bool "Serial-1" - help - Use serial port 1 for the console. - -config ETRAX_DEBUG_PORT2 - bool "Serial-2" - help - Use serial port 2 for the console. - -config ETRAX_DEBUG_PORT3 - bool "Serial-3" - help - Use serial port 3 for the console. - -config ETRAX_DEBUG_PORT_NULL - bool "disabled" - help - Disable serial-port debugging. - -endchoice - -choice - prompt "Kernel GDB port" - depends on ETRAX_KGDB - default ETRAX_KGDB_PORT0 - help - Choose a serial port for kernel debugging. NOTE: This port should - not be enabled under Drivers for built-in interfaces (as it has its - own initialization code) and should not be the same as the debug port. - -config ETRAX_KGDB_PORT0 - bool "Serial-0" - help - Use serial port 0 for kernel debugging. - -config ETRAX_KGDB_PORT1 - bool "Serial-1" - help - Use serial port 1 for kernel debugging. - -config ETRAX_KGDB_PORT2 - bool "Serial-2" - help - Use serial port 2 for kernel debugging. - -config ETRAX_KGDB_PORT3 - bool "Serial-3" - help - Use serial port 3 for kernel debugging. - -endchoice choice prompt "Product rescue-port" @@ -454,4 +393,6 @@ config ETRAX_POWERBUTTON_BIT help Configure where power button is connected. +endmenu + endif diff --git a/arch/cris/arch-v10/boot/Makefile b/arch/cris/arch-v10/boot/Makefile index e5b105851108..20c83a53caf3 100644 --- a/arch/cris/arch-v10/boot/Makefile +++ b/arch/cris/arch-v10/boot/Makefile @@ -1,13 +1,21 @@ # -# arch/cris/boot/Makefile +# arch/cris/arch-v10/boot/Makefile # -target = $(target_boot_dir) -src = $(src_boot_dir) -zImage: compressed/vmlinuz +OBJCOPY = objcopy-cris +OBJCOPYFLAGS = -O binary --remove-section=.bss -compressed/vmlinuz: - @$(MAKE) -f $(src)/compressed/Makefile $(target_compressed_dir)/vmlinuz +subdir- := compressed rescue +targets := Image -clean: - @$(MAKE) -f $(src)/compressed/Makefile clean +$(obj)/Image: vmlinux FORCE + $(call if_changed,objcopy) + @echo ' Kernel: $@ is ready' + +$(obj)/compressed/vmlinux: $(obj)/Image FORCE + $(Q)$(MAKE) $(build)=$(obj)/compressed $@ + $(Q)$(MAKE) $(build)=$(obj)/rescue $(obj)/rescue/rescue.bin + +$(obj)/zImage: $(obj)/compressed/vmlinux + @cp $< $@ + @echo ' Kernel: $@ is ready' diff --git a/arch/cris/arch-v10/boot/compressed/Makefile b/arch/cris/arch-v10/boot/compressed/Makefile index 6584a44820f4..4a031cb27eb9 100644 --- a/arch/cris/arch-v10/boot/compressed/Makefile +++ b/arch/cris/arch-v10/boot/compressed/Makefile @@ -1,45 +1,35 @@ # -# create a compressed vmlinuz image from the binary vmlinux.bin file +# arch/cris/arch-v10/boot/compressed/Makefile # -target = $(target_compressed_dir) -src = $(src_compressed_dir) CC = gcc-cris -melf $(LINUXINCLUDE) -CFLAGS = -O2 +ccflags-y += -O2 LD = ld-cris +ldflags-y += -T $(obj)/decompress.ld +OBJECTS = $(obj)/head.o $(obj)/misc.o OBJCOPY = objcopy-cris OBJCOPYFLAGS = -O binary --remove-section=.bss -OBJECTS = $(target)/head.o $(target)/misc.o -# files to compress -SYSTEM = $(objtree)/vmlinux.bin +quiet_cmd_image = BUILD $@ +cmd_image = cat $(obj)/decompress.bin $(obj)/piggy.gz > $@ -all: $(target_compressed_dir)/vmlinuz +targets := vmlinux piggy.gz decompress.o decompress.bin -$(target)/decompress.bin: $(OBJECTS) - $(LD) -T $(src)/decompress.ld -o $(target)/decompress.o $(OBJECTS) - $(OBJCOPY) $(OBJCOPYFLAGS) $(target)/decompress.o $(target)/decompress.bin +$(obj)/decompress.o: $(OBJECTS) FORCE + $(call if_changed,ld) -# Create vmlinuz image in top-level build directory -$(target_compressed_dir)/vmlinuz: $(target) piggy.img $(target)/decompress.bin - @echo " COMPR vmlinux.bin --> vmlinuz" - @cat $(target)/decompress.bin piggy.img > $(target_compressed_dir)/vmlinuz - @rm -f piggy.img +$(obj)/decompress.bin: $(obj)/decompress.o FORCE + $(call if_changed,objcopy) -$(target)/head.o: $(src)/head.S - $(CC) -D__ASSEMBLY__ -traditional -c $< -o $@ +$(obj)/head.o: $(obj)/head.S .config + @$(CC) -D__ASSEMBLY__ -traditional -c $< -o $@ -$(target)/misc.o: $(src)/misc.c - $(CC) -D__KERNEL__ -c $< -o $@ +$(obj)/misc.o: $(obj)/misc.c .config + @$(CC) -D__KERNEL__ -c $< -o $@ -# gzip the kernel image +$(obj)/vmlinux: $(obj)/piggy.gz $(obj)/decompress.bin FORCE + $(call if_changed,image) -piggy.img: $(SYSTEM) - @cat $(SYSTEM) | gzip -f -9 > piggy.img - -$(target): - mkdir -p $(target) - -clean: - rm -f piggy.img $(objtree)/vmlinuz +$(obj)/piggy.gz: $(obj)/../Image FORCE + $(call if_changed,gzip) diff --git a/arch/cris/arch-v10/boot/compressed/misc.c b/arch/cris/arch-v10/boot/compressed/misc.c index e205d2e7e089..9a43ab19391e 100644 --- a/arch/cris/arch-v10/boot/compressed/misc.c +++ b/arch/cris/arch-v10/boot/compressed/misc.c @@ -1,15 +1,13 @@ /* * misc.c * - * $Id: misc.c,v 1.6 2003/10/27 08:04:31 starvik Exp $ - * - * This is a collection of several routines from gzip-1.0.3 + * This is a collection of several routines from gzip-1.0.3 * adapted for Linux. * * malloc by Hannu Savolainen 1993 and Matthias Urlichs 1994 * puts by Nick Holloway 1993, better puts by Martin Mares 1995 * adaptation for Linux/CRIS Axis Communications AB, 1999 - * + * */ /* where the piggybacked kernel image expects itself to live. diff --git a/arch/cris/arch-v10/boot/rescue/Makefile b/arch/cris/arch-v10/boot/rescue/Makefile index 8be9b3130312..2e5045b9e19c 100644 --- a/arch/cris/arch-v10/boot/rescue/Makefile +++ b/arch/cris/arch-v10/boot/rescue/Makefile @@ -1,56 +1,38 @@ # -# Makefile for rescue code +# Makefile for rescue (bootstrap) code # -target = $(target_rescue_dir) -src = $(src_rescue_dir) CC = gcc-cris -mlinux $(LINUXINCLUDE) -CFLAGS = -O2 +ccflags-y += -O2 +asflags-y += -traditional LD = gcc-cris -mlinux -nostdlib +ldflags-y += -T $(obj)/rescue.ld OBJCOPY = objcopy-cris OBJCOPYFLAGS = -O binary --remove-section=.bss +obj-$(CONFIG_ETRAX_AXISFLASHMAP) = head.o +OBJECT := $(obj)/head.o -all: $(target)/rescue.bin $(target)/testrescue.bin $(target)/kimagerescue.bin +targets := rescue.o rescue.bin -$(target)/rescue.bin: $(target) $(target)/head.o - $(LD) -T $(src)/rescue.ld -o $(target)/rescue.o $(target)/head.o - $(OBJCOPY) $(OBJCOPYFLAGS) $(target)/rescue.o $(target)/rescue.bin -# Place a copy in top-level build directory - cp -p $(target)/rescue.bin $(objtree) +$(obj)/rescue.o: $(OBJECT) FORCE + $(call if_changed,ld) -$(target)/testrescue.bin: $(target) $(target)/testrescue.o - $(OBJCOPY) $(OBJCOPYFLAGS) $(target)/testrescue.o tr.bin +$(obj)/rescue.bin: $(obj)/rescue.o FORCE + $(call if_changed,objcopy) + cp -p $(obj)/rescue.bin $(objtree) + +$(obj)/testrescue.bin: $(obj)/testrescue.o + $(OBJCOPY) $(OBJCOPYFLAGS) $(obj)/testrescue.o tr.bin # Pad it to 784 bytes dd if=/dev/zero of=tmp2423 bs=1 count=784 cat tr.bin tmp2423 >testrescue_tmp.bin - dd if=testrescue_tmp.bin of=$(target)/testrescue.bin bs=1 count=784 + dd if=testrescue_tmp.bin of=$(obj)/testrescue.bin bs=1 count=784 rm tr.bin tmp2423 testrescue_tmp.bin -$(target)/kimagerescue.bin: $(target) $(target)/kimagerescue.o - $(OBJCOPY) $(OBJCOPYFLAGS) $(target)/kimagerescue.o ktr.bin +$(obj)/kimagerescue.bin: $(obj)/kimagerescue.o + $(OBJCOPY) $(OBJCOPYFLAGS) $(obj)/kimagerescue.o ktr.bin # Pad it to 784 bytes, that's what the rescue loader expects dd if=/dev/zero of=tmp2423 bs=1 count=784 cat ktr.bin tmp2423 >kimagerescue_tmp.bin - dd if=kimagerescue_tmp.bin of=$(target)/kimagerescue.bin bs=1 count=784 + dd if=kimagerescue_tmp.bin of=$(obj)/kimagerescue.bin bs=1 count=784 rm ktr.bin tmp2423 kimagerescue_tmp.bin - -$(target): - mkdir -p $(target) - -$(target)/head.o: $(src)/head.S - $(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o - -$(target)/testrescue.o: $(src)/testrescue.S - $(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o - -$(target)/kimagerescue.o: $(src)/kimagerescue.S - $(CC) -D__ASSEMBLY__ -traditional -c $< -o $*.o - -clean: - rm -f $(target)/*.o $(target)/*.bin - -fastdep: - -modules: - -modules-install: diff --git a/arch/cris/arch-v10/boot/rescue/head.S b/arch/cris/arch-v10/boot/rescue/head.S index f223cc0c00bb..6ba7be8ac4a0 100644 --- a/arch/cris/arch-v10/boot/rescue/head.S +++ b/arch/cris/arch-v10/boot/rescue/head.S @@ -1,5 +1,4 @@ -/* $Id: head.S,v 1.7 2005/03/07 12:11:06 starvik Exp $ - * +/* * Rescue code, made to reside at the beginning of the * flash-memory. when it starts, it checks a partition * table at the first sector after the rescue sector. @@ -23,20 +22,20 @@ * Partition table format: * * Code transparency: - * + * * 2 bytes [opcode 'nop'] * 2 bytes [opcode 'di'] * 4 bytes [opcode 'ba <offset>', 8-bit or 16-bit version] * 2 bytes [opcode 'nop', delay slot] * - * Table validation (at +10): - * + * Table validation (at +10): + * * 2 bytes [magic/version word for partitiontable - 0xef, 0xbe] * 2 bytes [length of all entries plus the end marker] * 4 bytes [checksum for the partitiontable itself] * - * Entries, each with the following format, last has offset -1: - * + * Entries, each with the following format, last has offset -1: + * * 4 bytes [offset in bytes, from start of flash] * 4 bytes [length in bytes of partition] * 4 bytes [checksum, simple longword sum] @@ -47,9 +46,9 @@ * End marker * * 4 bytes [-1] - * + * * 10 bytes [0, padding] - * + * * Bit 0 in flags signifies RW or RO. The rescue code only bothers * to check the checksum for RO partitions, since the others will * change their data without updating the checksums. A 1 in bit 0 @@ -59,26 +58,29 @@ * * During the wait for serial input, the status LED will flash so the * user knows something went wrong. - * - * Copyright (C) 1999, 2000, 2001, 2002, 2003 Axis Communications AB + * + * Copyright (C) 1999-2007 Axis Communications AB */ +#ifdef CONFIG_ETRAX_AXISFLASHMAP + #define ASSEMBLER_MACROS_ONLY #include <asm/arch/sv_addr_ag.h> ;; The partitiontable is looked for at the first sector after the boot ;; sector. Sector size is 65536 bytes in all flashes we use. - + #define PTABLE_START CONFIG_ETRAX_PTABLE_SECTOR #define PTABLE_MAGIC 0xbeef ;; The normal Etrax100 on-chip boot ROM does serial boot at 0x380000f0. - ;; That is not where we put our downloaded serial boot-code. The length is - ;; enough for downloading code that loads the rest of itself (after - ;; having setup the DRAM etc). It is the same length as the on-chip - ;; ROM loads, so the same host loader can be used to load a rescued - ;; product as well as one booted through the Etrax serial boot code. - + ;; That is not where we put our downloaded serial boot-code. + ;; The length is enough for downloading code that loads the rest + ;; of itself (after having setup the DRAM etc). + ;; It is the same length as the on-chip ROM loads, so the same + ;; host loader can be used to load a rescued product as well as + ;; one booted through the Etrax serial boot code. + #define CODE_START 0x40000000 #define CODE_LENGTH 784 @@ -102,7 +104,7 @@ #define SERRECC R_SERIAL2_REC_CTRL #define SERRDAT R_SERIAL2_REC_DATA #define SERSTAT R_SERIAL2_STATUS -#endif +#endif #ifdef CONFIG_ETRAX_RESCUE_SER3 #define SERXOFF R_SERIAL3_XOFF #define SERBAUD R_SERIAL3_BAUD @@ -115,60 +117,61 @@ #define RAM_INIT_MAGIC 0x56902387 .text - + ;; This is the entry point of the rescue code ;; 0x80000000 if loaded in flash (as it should be) - ;; since etrax actually starts at address 2 when booting from flash, we + ;; Since etrax actually starts at address 2 when booting from flash, we ;; put a nop (2 bytes) here first so we dont accidentally skip the di - nop + nop di jump in_cache ; enter cached area instead in_cache: - ;; first put a jump test to give a possibility of upgrading the rescue code - ;; without erasing/reflashing the sector. we put a longword of -1 here and if - ;; it is not -1, we jump using the value as jump target. since we can always - ;; change 1's to 0's without erasing the sector, it is possible to add new + ;; First put a jump test to give a possibility of upgrading the + ;; rescue code without erasing/reflashing the sector. + ;; We put a longword of -1 here and if it is not -1, we jump using + ;; the value as jump target. Since we can always change 1's to 0's + ;; without erasing the sector, it is possible to add new ;; code after this and altering the jumptarget in an upgrade. jtcd: move.d [jumptarget], $r0 cmp.d 0xffffffff, $r0 beq no_newjump nop - + jump [$r0] -jumptarget: +jumptarget: .dword 0xffffffff ; can be overwritten later to insert new code - + no_newjump: -#ifdef CONFIG_ETRAX_ETHERNET +#ifdef CONFIG_ETRAX_ETHERNET ;; Start MII clock to make sure it is running when tranceiver is reset move.d 0x3, $r0 ; enable = on, phy = mii_clk move.d $r0, [R_NETWORK_GEN_CONFIG] #endif - + ;; We need to setup the bus registers before we start using the DRAM #include "../../lib/dram_init.S" ;; we now should go through the checksum-table and check the listed ;; partitions for errors. - + move.d PTABLE_START, $r3 move.d [$r3], $r0 cmp.d NOP_DI, $r0 ; make sure the nop/di is there... bne do_rescue nop - + ;; skip the code transparency block (10 bytes). addq 10, $r3 - + ;; check for correct magic - + move.w [$r3+], $r0 cmp.w PTABLE_MAGIC, $r0 bne do_rescue ; didn't recognize - trig rescue @@ -186,11 +189,11 @@ no_newjump: cmp.d $r0, $r4 bne do_rescue ; didn't match - trig rescue nop - + ;; ptable is ok. validate each entry. moveq -1, $r7 - + ploop: move.d [$r3+], $r1 ; partition offset (from ptable start) bne notfirst ; check if it is the partition containing ptable nop ; yes.. @@ -199,7 +202,7 @@ ploop: move.d [$r3+], $r1 ; partition offset (from ptable start) sub.d $r8, $r2 ; minus the ptable length ba bosse nop -notfirst: +notfirst: cmp.d -1, $r1 ; the end of the ptable ? beq flash_ok ; if so, the flash is validated move.d [$r3+], $r2 ; partition length @@ -213,47 +216,46 @@ bosse: move.d [$r3+], $r5 ; checksum bpl 1f nop move.d $r1, $r7 ; remember boot partition offset -1: - +1: add.d PTABLE_START, $r1 - + jsr checksum ; checksum the partition - + cmp.d $r0, $r5 beq ploop ; checksums matched, go to next entry nop ;; otherwise fall through to the rescue code. - + do_rescue: ;; setup port PA and PB default initial directions and data ;; (so we can flash LEDs, and so that DTR and others are set) - + move.b CONFIG_ETRAX_DEF_R_PORT_PA_DIR, $r0 move.b $r0, [R_PORT_PA_DIR] move.b CONFIG_ETRAX_DEF_R_PORT_PA_DATA, $r0 move.b $r0, [R_PORT_PA_DATA] - + move.b CONFIG_ETRAX_DEF_R_PORT_PB_DIR, $r0 move.b $r0, [R_PORT_PB_DIR] move.b CONFIG_ETRAX_DEF_R_PORT_PB_DATA, $r0 move.b $r0, [R_PORT_PB_DATA] ;; setup the serial port at 115200 baud - + moveq 0, $r0 - move.d $r0, [SERXOFF] + move.d $r0, [SERXOFF] move.b 0x99, $r0 - move.b $r0, [SERBAUD] ; 115.2kbaud for both transmit and receive + move.b $r0, [SERBAUD] ; 115.2kbaud for both transmit and receive - move.b 0x40, $r0 ; rec enable - move.b $r0, [SERRECC] + move.b 0x40, $r0 ; rec enable + move.b $r0, [SERRECC] moveq 0, $r1 ; "timer" to clock out a LED red flash move.d CODE_START, $r3 ; destination counter movu.w CODE_LENGTH, $r4; length - + wait_ser: addq 1, $r1 #ifndef CONFIG_ETRAX_NO_LEDS @@ -272,20 +274,20 @@ wait_ser: nop 1: not $r0 ; clear bit and.d $r0, $r2 -2: +2: #ifdef CONFIG_ETRAX_PA_LEDS - move.b $r2, [R_PORT_PA_DATA] -#endif + move.b $r2, [R_PORT_PA_DATA] +#endif #ifdef CONFIG_ETRAX_PB_LEDS - move.b $r2, [R_PORT_PB_DATA] + move.b $r2, [R_PORT_PB_DATA] #endif #ifdef CONFIG_ETRAX_90000000_LEDS move.b $r2, [0x90000000] #endif #endif - + ;; check if we got something on the serial port - + move.b [SERSTAT], $r0 btstq 0, $r0 ; data_avail bpl wait_ser @@ -295,14 +297,15 @@ wait_ser: move.b [SERRDAT], $r0 move.b $r0, [$r3+] - + subq 1, $r4 ; decrease length bne wait_ser nop ;; jump into downloaded code - move.d RAM_INIT_MAGIC, $r8 ; Tell next product that DRAM is initialized + move.d RAM_INIT_MAGIC, $r8 ; Tell next product that DRAM is + ; initialized jump CODE_START flash_ok: @@ -313,7 +316,8 @@ flash_ok: nop move.d PTABLE_START, $r7; otherwise use the ptable start 1: - move.d RAM_INIT_MAGIC, $r8 ; Tell next product that DRAM is initialized + move.d RAM_INIT_MAGIC, $r8 ; Tell next product that DRAM is + ; initialized jump $r7 ; boot! @@ -327,7 +331,8 @@ checksum: moveq 0, $r0 moveq CONFIG_ETRAX_FLASH1_SIZE, $r6 - ;; If the first physical flash memory is exceeded wrap to the second one. + ;; If the first physical flash memory is exceeded wrap to the + ;; second one btstq 26, $r1 ; Are we addressing first flash? bpl 1f nop @@ -351,3 +356,5 @@ checksum: 3: move.d MEM_CSE1_START, $r1 ; wrap to second flash ba 2b nop + +#endif diff --git a/arch/cris/arch-v10/boot/rescue/kimagerescue.S b/arch/cris/arch-v10/boot/rescue/kimagerescue.S index cbccd6316d39..55eeff8bb08e 100644 --- a/arch/cris/arch-v10/boot/rescue/kimagerescue.S +++ b/arch/cris/arch-v10/boot/rescue/kimagerescue.S @@ -1,5 +1,4 @@ -/* $Id: kimagerescue.S,v 1.1 2001/12/17 13:59:27 bjornw Exp $ - * +/* * Rescue code to be prepended on a kimage and copied to the * rescue serial port. * This is called from the rescue code, it will copy received data to @@ -7,13 +6,13 @@ */ #define ASSEMBLER_MACROS_ONLY -#include <asm/sv_addr_ag.h> +#include <asm/arch/sv_addr_ag.h> #define CODE_START 0x40004000 #define CODE_LENGTH 784 #define TIMEOUT_VALUE 1000 - - + + #ifdef CONFIG_ETRAX_RESCUE_SER0 #define SERXOFF R_SERIAL0_XOFF #define SERBAUD R_SERIAL0_BAUD @@ -34,7 +33,7 @@ #define SERRECC R_SERIAL2_REC_CTRL #define SERRDAT R_SERIAL2_REC_DATA #define SERSTAT R_SERIAL2_STATUS -#endif +#endif #ifdef CONFIG_ETRAX_RESCUE_SER3 #define SERXOFF R_SERIAL3_XOFF #define SERBAUD R_SERIAL3_BAUD @@ -48,54 +47,55 @@ ;; 0x80000000 if loaded in flash (as it should be) ;; since etrax actually starts at address 2 when booting from flash, we ;; put a nop (2 bytes) here first so we dont accidentally skip the di - - nop + + nop di -#ifndef CONFIG_SVINTO_SIM +#ifndef CONFIG_SVINTO_SIM ;; setup port PA and PB default initial directions and data ;; (so we can flash LEDs, and so that DTR and others are set) - + move.b CONFIG_ETRAX_DEF_R_PORT_PA_DIR, $r0 move.b $r0, [R_PORT_PA_DIR] move.b CONFIG_ETRAX_DEF_R_PORT_PA_DATA, $r0 move.b $r0, [R_PORT_PA_DATA] - + move.b CONFIG_ETRAX_DEF_R_PORT_PB_DIR, $r0 move.b $r0, [R_PORT_PB_DIR] move.b CONFIG_ETRAX_DEF_R_PORT_PB_DATA, $r0 move.b $r0, [R_PORT_PB_DATA] - + ;; We need to setup the bus registers before we start using the DRAM #include "../../lib/dram_init.S" - + #endif ;; Setup the stack to a suitably high address. ;; We assume 8 MB is the minimum DRAM in an eLinux ;; product and put the sp at the top for now. move.d 0x40800000, $sp - + ;; setup the serial port at 115200 baud - + moveq 0, $r0 - move.d $r0, [SERXOFF] + move.d $r0, [SERXOFF] move.b 0x99, $r0 - move.b $r0, [SERBAUD] ; 115.2kbaud for both transmit and receive + move.b $r0, [SERBAUD] ; 115.2kbaud for both transmit + ; and receive move.b 0x40, $r0 ; rec enable - move.b $r0, [SERRECC] + move.b $r0, [SERRECC] - moveq 0, $r1 ; "timer" to clock out a LED red flash - move.d CODE_START, $r3 ; destination counter + moveq 0, $r1 ; "timer" to clock out a LED red flash + move.d CODE_START, $r3 ; destination counter move.d CODE_LENGTH, $r4 ; length move.d TIMEOUT_VALUE, $r5 ; "timeout" until jump wait_ser: addq 1, $r1 - subq 1, $r5 ; decrease timeout - beq jump_start ; timed out + subq 1, $r5 ; decrease timeout + beq jump_start ; timed out nop #ifndef CONFIG_ETRAX_NO_LEDS #ifdef CONFIG_ETRAX_PA_LEDS @@ -111,21 +111,21 @@ wait_ser: or.d $r0, $r2 ; set bit ba 2f nop -1: not $r0 ; clear bit +1: not $r0 ; clear bit and.d $r0, $r2 -2: +2: #ifdef CONFIG_ETRAX_PA_LEDS move.b $r2, [R_PORT_PA_DATA] -#endif +#endif #ifdef CONFIG_ETRAX_PB_LEDS move.b $r2, [R_PORT_PB_DATA] #endif #endif - + ;; check if we got something on the serial port - + move.b [SERSTAT], $r0 - btstq 0, $r0 ; data_avail + btstq 0, $r0 ; data_avail bpl wait_ser nop @@ -134,7 +134,7 @@ wait_ser: move.b [SERRDAT], $r0 move.b $r0, [$r3+] move.d TIMEOUT_VALUE, $r5 ; reset "timeout" - subq 1, $r4 ; decrease length + subq 1, $r4 ; decrease length bne wait_ser nop jump_start: diff --git a/arch/cris/arch-v10/boot/rescue/testrescue.S b/arch/cris/arch-v10/boot/rescue/testrescue.S index 566a9f341254..2d937f9afe23 100644 --- a/arch/cris/arch-v10/boot/rescue/testrescue.S +++ b/arch/cris/arch-v10/boot/rescue/testrescue.S @@ -1,13 +1,12 @@ -/* $Id: testrescue.S,v 1.1 2001/12/17 13:59:27 bjornw Exp $ - * +/* * Simple testcode to download by the rescue block. - * Just lits some LEDs to show it was downloaded correctly. - * + * Just lights some LEDs to show it was downloaded correctly. + * * Copyright (C) 1999 Axis Communications AB */ #define ASSEMBLER_MACROS_ONLY -#include <asm/sv_addr_ag.h> +#include <asm/arch/sv_addr_ag.h> .text @@ -16,11 +15,10 @@ moveq -1, $r2 move.b $r2, [R_PORT_PA_DIR] moveq 0, $r2 - move.b $r2, [R_PORT_PA_DATA] + move.b $r2, [R_PORT_PA_DATA] endless: nop ba endless nop - diff --git a/arch/cris/arch-v10/drivers/Kconfig b/arch/cris/arch-v10/drivers/Kconfig index 96740ef497d4..58f5864a6680 100644 --- a/arch/cris/arch-v10/drivers/Kconfig +++ b/arch/cris/arch-v10/drivers/Kconfig @@ -9,37 +9,6 @@ config ETRAX_ETHERNET This option enables the ETRAX 100LX built-in 10/100Mbit Ethernet controller. -choice - prompt "Network LED behavior" - depends on ETRAX_ETHERNET - default ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY - -config ETRAX_NETWORK_LED_ON_WHEN_LINK - bool "LED_on_when_link" - help - Selecting LED_on_when_link will light the LED when there is a - connection and will flash off when there is activity. - - Selecting LED_on_when_activity will light the LED only when - there is activity. - - This setting will also affect the behaviour of other activity LEDs - e.g. Bluetooth. - -config ETRAX_NETWORK_LED_ON_WHEN_ACTIVITY - bool "LED_on_when_activity" - help - Selecting LED_on_when_link will light the LED when there is a - connection and will flash off when there is activity. - - Selecting LED_on_when_activity will light the LED only when - there is activity. - - This setting will also affect the behaviour of other activity LEDs - e.g. Bluetooth. - -endchoice - config ETRAX_SERIAL bool "Serial-port support" depends on ETRAX_ARCH_V10 @@ -84,32 +53,6 @@ config ETRAX_SERIAL_PORT0 the same DMA channels. choice - prompt "Ser0 DMA out assignment" - depends on ETRAX_SERIAL_PORT0 - default ETRAX_SERIAL_PORT0_DMA6_OUT - -config ETRAX_SERIAL_PORT0_NO_DMA_OUT - bool "No DMA out" - -config ETRAX_SERIAL_PORT0_DMA6_OUT - bool "DMA 6" - -endchoice - -choice - prompt "Ser0 DMA in assignment" - depends on ETRAX_SERIAL_PORT0 - default ETRAX_SERIAL_PORT0_DMA7_IN - -config ETRAX_SERIAL_PORT0_NO_DMA_IN - bool "No DMA in" - -config ETRAX_SERIAL_PORT0_DMA7_IN - bool "DMA 7" - -endchoice - -choice prompt "Ser0 DTR, RI, DSR and CD assignment" depends on ETRAX_SERIAL_PORT0 default ETRAX_SER0_DTR_RI_DSR_CD_ON_NONE @@ -198,32 +141,6 @@ config ETRAX_SERIAL_PORT1 Enables the ETRAX 100 serial driver for ser1 (ttyS1). choice - prompt "Ser1 DMA out assignment" - depends on ETRAX_SERIAL_PORT1 - default ETRAX_SERIAL_PORT1_DMA8_OUT - -config ETRAX_SERIAL_PORT1_NO_DMA_OUT - bool "No DMA out" - -config ETRAX_SERIAL_PORT1_DMA8_OUT - bool "DMA 8" - -endchoice - -choice - prompt "Ser1 DMA in assignment" - depends on ETRAX_SERIAL_PORT1 - default ETRAX_SERIAL_PORT1_DMA9_IN - -config ETRAX_SERIAL_PORT1_NO_DMA_IN - bool "No DMA in" - -config ETRAX_SERIAL_PORT1_DMA9_IN - bool "DMA 9" - -endchoice - -choice prompt "Ser1 DTR, RI, DSR and CD assignment" depends on ETRAX_SERIAL_PORT1 default ETRAX_SER1_DTR_RI_DSR_CD_ON_NONE @@ -315,32 +232,6 @@ config ETRAX_SERIAL_PORT2 Enables the ETRAX 100 serial driver for ser2 (ttyS2). choice - prompt "Ser2 DMA out assignment" - depends on ETRAX_SERIAL_PORT2 - default ETRAX_SERIAL_PORT2_DMA2_OUT - -config ETRAX_SERIAL_PORT2_NO_DMA_OUT - bool "No DMA out" - -config ETRAX_SERIAL_PORT2_DMA2_OUT - bool "DMA 2" - -endchoice - -choice - prompt "Ser2 DMA in assignment" - depends on ETRAX_SERIAL_PORT2 - default ETRAX_SERIAL_PORT2_DMA3_IN - -config ETRAX_SERIAL_PORT2_NO_DMA_IN - bool "No DMA in" - -config ETRAX_SERIAL_PORT2_DMA3_IN - bool "DMA 3" - -endchoice - -choice prompt "Ser2 DTR, RI, DSR and CD assignment" depends on ETRAX_SERIAL_PORT2 default ETRAX_SER2_DTR_RI_DSR_CD_ON_NONE @@ -429,32 +320,6 @@ config ETRAX_SERIAL_PORT3 Enables the ETRAX 100 serial driver for ser3 (ttyS3). choice - prompt "Ser3 DMA out assignment" - depends on ETRAX_SERIAL_PORT3 - default ETRAX_SERIAL_PORT3_DMA4_OUT - -config ETRAX_SERIAL_PORT3_NO_DMA_OUT - bool "No DMA out" - -config ETRAX_SERIAL_PORT3_DMA4_OUT - bool "DMA 4" - -endchoice - -choice - prompt "Ser3 DMA in assignment" - depends on ETRAX_SERIAL_PORT3 - default ETRAX_SERIAL_PORT3_DMA5_IN - -config ETRAX_SERIAL_PORT3_NO_DMA_IN - bool "No DMA in" - -config ETRAX_SERIAL_PORT3_DMA5_IN - bool "DMA 5" - -endchoice - -choice prompt "Ser3 DTR, RI, DSR and CD assignment" depends on ETRAX_SERIAL_PORT3 default ETRAX_SER3_DTR_RI_DSR_CD_ON_NONE @@ -563,21 +428,6 @@ config ETRAX_USB_HOST_PORT2 depends on ETRAX_USB_HOST default n -config ETRAX_AXISFLASHMAP - bool "Axis flash-map support" - depends on ETRAX_ARCH_V10 - select MTD - select MTD_CFI - select MTD_CFI_AMDSTD - select MTD_CHAR - select MTD_BLOCK - select MTD_PARTITIONS - select MTD_CONCAT - select MTD_COMPLEX_MAPPINGS - help - This option enables MTD mapping of flash devices. Needed to use - flash memories. If unsure, say Y. - config ETRAX_PTABLE_SECTOR int "Byte-offset of partition table sector" depends on ETRAX_AXISFLASHMAP @@ -731,37 +581,6 @@ config ETRAX_PB_CHANGEABLE_BITS Bit set = changeable. You probably want 00 here. -config ETRAX_RTC - bool "Real Time Clock support" - depends on ETRAX_ARCH_V10 - help - Enables drivers for the Real-Time Clock battery-backed chips on - some products. The kernel reads the time when booting, and - the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a - rtc_time struct (see <file:include/asm-cris/rtc.h>) on the /dev/rtc - device, major 121. You can check the time with cat /proc/rtc, but - normal time reading should be done using libc function time and - friends. - -choice - prompt "RTC chip" - depends on ETRAX_RTC - default ETRAX_DS1302 - -config ETRAX_DS1302 - bool "DS1302" - help - Enables the driver for the DS1302 Real-Time Clock battery-backed - chip on some products. - -config ETRAX_PCF8563 - bool "PCF8563" - help - Enables the driver for the PCF8563 Real-Time Clock battery-backed - chip on some products. - -endchoice - config ETRAX_DS1302_RST_ON_GENERIC_PORT bool "DS1302 RST on Generic Port" depends on ETRAX_DS1302 diff --git a/arch/cris/arch-v10/drivers/Makefile b/arch/cris/arch-v10/drivers/Makefile index 20258e36f384..44bf2e88c26e 100644 --- a/arch/cris/arch-v10/drivers/Makefile +++ b/arch/cris/arch-v10/drivers/Makefile @@ -2,11 +2,11 @@ # Makefile for Etrax-specific drivers # -obj-$(CONFIG_ETRAX_AXISFLASHMAP) += axisflashmap.o -obj-$(CONFIG_ETRAX_I2C) += i2c.o -obj-$(CONFIG_ETRAX_I2C_EEPROM) += eeprom.o -obj-$(CONFIG_ETRAX_GPIO) += gpio.o -obj-$(CONFIG_ETRAX_DS1302) += ds1302.o +obj-$(CONFIG_ETRAX_AXISFLASHMAP) += axisflashmap.o +obj-$(CONFIG_ETRAX_I2C) += i2c.o +obj-$(CONFIG_ETRAX_I2C_EEPROM) += eeprom.o +obj-$(CONFIG_ETRAX_GPIO) += gpio.o +obj-$(CONFIG_ETRAX_DS1302) += ds1302.o obj-$(CONFIG_ETRAX_PCF8563) += pcf8563.o - +obj-$(CONFIG_ETRAX_SYNCHRONOUS_SERIAL) += sync_serial.o diff --git a/arch/cris/arch-v10/drivers/axisflashmap.c b/arch/cris/arch-v10/drivers/axisflashmap.c index ea3cf2e39a14..b3bdda93ffef 100644 --- a/arch/cris/arch-v10/drivers/axisflashmap.c +++ b/arch/cris/arch-v10/drivers/axisflashmap.c @@ -10,129 +10,6 @@ * tells us what other partitions to define. If there isn't, we use a default * partition split defined below. * - * $Log: axisflashmap.c,v $ - * Revision 1.11 2004/11/15 10:27:14 starvik - * Corrected typo (Thanks to Milton Miller <miltonm@bga.com>). - * - * Revision 1.10 2004/08/16 12:37:22 starvik - * Merge of Linux 2.6.8 - * - * Revision 1.8 2004/05/14 07:58:03 starvik - * Merge of changes from 2.4 - * - * Revision 1.6 2003/07/04 08:27:37 starvik - * Merge of Linux 2.5.74 - * - * Revision 1.5 2002/12/11 13:13:57 starvik - * Added arch/ to v10 specific includes - * Added fix from Linux 2.4 in serial.c (flush_to_flip_buffer) - * - * Revision 1.4 2002/11/20 11:56:10 starvik - * Merge of Linux 2.5.48 - * - * Revision 1.3 2002/11/13 14:54:13 starvik - * Copied from linux 2.4 - * - * Revision 1.28 2002/10/01 08:08:43 jonashg - * The first partition ends at the start of the partition table. - * - * Revision 1.27 2002/08/21 09:23:13 jonashg - * Speling. - * - * Revision 1.26 2002/08/21 08:35:20 jonashg - * Cosmetic change to printouts. - * - * Revision 1.25 2002/08/21 08:15:42 jonashg - * Made it compile even without CONFIG_MTD_CONCAT defined. - * - * Revision 1.24 2002/08/20 13:12:35 jonashg - * * New approach to probing. Probe cse0 and cse1 separately and (mtd)concat - * the results. - * * Removed compile time tests concerning how the mtdram driver has been - * configured. The user will know about the misconfiguration at runtime - * instead. (The old approach made it impossible to use mtdram for anything - * else than RAM boot). - * - * Revision 1.23 2002/05/13 12:12:28 johana - * Allow compile without CONFIG_MTD_MTDRAM but warn at compiletime and - * be informative at runtime. - * - * Revision 1.22 2002/05/13 10:24:44 johana - * Added #if checks on MTDRAM CONFIG - * - * Revision 1.21 2002/05/06 16:05:20 johana - * Removed debug printout. - * - * Revision 1.20 2002/05/06 16:03:00 johana - * No more cramfs as root hack in generic code. - * It's handled by axisflashmap using mtdram. - * - * Revision 1.19 2002/03/15 17:10:28 bjornw - * Changed comment about cached access since we changed this before - * - * Revision 1.18 2002/03/05 17:06:15 jonashg - * Try amd_flash probe before cfi_probe since amd_flash driver can handle two - * (or more) flash chips of different model and the cfi driver cannot. - * - * Revision 1.17 2001/11/12 19:42:38 pkj - * Fixed compiler warnings. - * - * Revision 1.16 2001/11/08 11:18:58 jonashg - * Always read from uncached address to avoid problems with flushing - * cachelines after write and MTD-erase. No performance loss have been - * seen yet. - * - * Revision 1.15 2001/10/19 12:41:04 jonashg - * Name of probe has changed in MTD. - * - * Revision 1.14 2001/09/21 07:14:10 jonashg - * Made root filesystem (cramfs) use mtdblock driver when booting from flash. - * - * Revision 1.13 2001/08/15 13:57:35 jonashg - * Entire MTD updated to the linux 2.4.7 version. - * - * Revision 1.12 2001/06/11 09:50:30 jonashg - * Oops, 2MB is 0x200000 bytes. - * - * Revision 1.11 2001/06/08 11:39:44 jonashg - * Changed sizes and offsets in axis_default_partitions to use - * CONFIG_ETRAX_PTABLE_SECTOR. - * - * Revision 1.10 2001/05/29 09:42:03 jonashg - * Use macro for end marker length instead of sizeof. - * - * Revision 1.9 2001/05/29 08:52:52 jonashg - * Gave names to the magic fours (size of the ptable end marker). - * - * Revision 1.8 2001/05/28 15:36:20 jonashg - * * Removed old comment about ptable location in flash (it's a CONFIG_ option). - * * Variable ptable was initialized twice to the same value. - * - * Revision 1.7 2001/04/05 13:41:46 markusl - * Updated according to review remarks - * - * Revision 1.6 2001/03/07 09:21:21 bjornw - * No need to waste .data - * - * Revision 1.5 2001/03/06 16:27:01 jonashg - * Probe the entire flash area for flash devices. - * - * Revision 1.4 2001/02/23 12:47:15 bjornw - * Uncached flash in LOW_MAP moved from 0xe to 0x8 - * - * Revision 1.3 2001/02/16 12:11:45 jonashg - * MTD driver amd_flash is now included in MTD CVS repository. - * (It's now in drivers/mtd). - * - * Revision 1.2 2001/02/09 11:12:22 jonashg - * Support for AMD compatible non-CFI flash chips. - * Only tested with Toshiba TC58FVT160 so far. - * - * Revision 1.1 2001/01/12 17:01:18 bjornw - * * Added axisflashmap.c, a physical mapping for MTD that reads and understands - * Axis partition-table format. - * - * */ #include <linux/module.h> @@ -235,7 +112,7 @@ static struct map_info map_cse1 = { }; /* If no partition-table was found, we use this default-set. */ -#define MAX_PARTITIONS 7 +#define MAX_PARTITIONS 7 #define NUM_DEFAULT_PARTITIONS 3 /* @@ -300,6 +177,15 @@ static struct mtd_partition axis_partitions[MAX_PARTITIONS] = { }, }; +#ifdef CONFIG_ETRAX_AXISFLASHMAP_MTD0WHOLE +/* Main flash device */ +static struct mtd_partition main_partition = { + .name = "main", + .size = 0, + .offset = 0 +}; +#endif + /* * Probe a chip select for AMD-compatible (JEDEC) or CFI-compatible flash * chips in that order (because the amd_flash-driver is faster). @@ -316,15 +202,14 @@ static struct mtd_info *probe_cs(struct map_info *map_cs) mtd_cs = do_map_probe("cfi_probe", map_cs); #endif #ifdef CONFIG_MTD_JEDECPROBE - if (!mtd_cs) { + if (!mtd_cs) mtd_cs = do_map_probe("jedec_probe", map_cs); - } #endif return mtd_cs; } -/* +/* * Probe each chip select individually for flash chips. If there are chips on * both cse0 and cse1, the mtd_info structs will be concatenated to one struct * so that MTD partitions can cross chip boundries. @@ -351,7 +236,7 @@ static struct mtd_info *flash_probe(void) if (mtd_cse0 && mtd_cse1) { #ifdef CONFIG_MTD_CONCAT struct mtd_info *mtds[] = { mtd_cse0, mtd_cse1 }; - + /* Since the concatenation layer adds a small overhead we * could try to figure out if the chips in cse0 and cse1 are * identical and reprobe the whole cse0+cse1 window. But since @@ -372,7 +257,7 @@ static struct mtd_info *flash_probe(void) /* The best we can do now is to only use what we found * at cse0. - */ + */ mtd_cse = mtd_cse0; map_destroy(mtd_cse1); } @@ -395,7 +280,7 @@ static int __init init_axis_flash(void) struct partitiontable_head *ptable_head = NULL; struct partitiontable_entry *ptable; int use_default_ptable = 1; /* Until proven otherwise. */ - const char *pmsg = " /dev/flash%d at 0x%08x, size 0x%08x\n"; + const char pmsg[] = " /dev/flash%d at 0x%08x, size 0x%08x\n"; if (!(mymtd = flash_probe())) { /* There's no reason to use this module if no flash chip can @@ -435,7 +320,7 @@ static int __init init_axis_flash(void) unsigned long offset = CONFIG_ETRAX_PTABLE_SECTOR; unsigned char *p; unsigned long csum = 0; - + ptable = (struct partitiontable_entry *) ((unsigned long)ptable_head + sizeof(*ptable_head)); @@ -490,6 +375,16 @@ static int __init init_axis_flash(void) pidx++; } +#ifdef CONFIG_ETRAX_AXISFLASHMAP_MTD0WHOLE + if (mymtd) { + main_partition.size = mymtd->size; + err = add_mtd_partitions(mymtd, &main_partition, 1); + if (err) + panic("axisflashmap: Could not initialize " + "partition for whole main mtd device!\n"); + } +#endif + if (mymtd) { if (use_default_ptable) { printk(KERN_INFO " Using default partition table.\n"); @@ -499,9 +394,8 @@ static int __init init_axis_flash(void) err = add_mtd_partitions(mymtd, axis_partitions, pidx); } - if (err) { + if (err) panic("axisflashmap could not add MTD partitions!\n"); - } } if (!romfs_in_flash) { @@ -515,25 +409,24 @@ static int __init init_axis_flash(void) #else struct mtd_info *mtd_ram; - mtd_ram = kmalloc(sizeof(struct mtd_info), - GFP_KERNEL); - if (!mtd_ram) { + mtd_ram = kmalloc(sizeof(struct mtd_info), GFP_KERNEL); + if (!mtd_ram) panic("axisflashmap couldn't allocate memory for " "mtd_info!\n"); - } printk(KERN_INFO " Adding RAM partition for romfs image:\n"); - printk(pmsg, pidx, romfs_start, romfs_length); - - err = mtdram_init_device(mtd_ram, (void*)romfs_start, - romfs_length, "romfs"); - if (err) { + printk(pmsg, pidx, (unsigned)romfs_start, + (unsigned)romfs_length); + + err = mtdram_init_device(mtd_ram, + (void *)romfs_start, + romfs_length, + "romfs"); + if (err) panic("axisflashmap could not initialize MTD RAM " "device!\n"); - } #endif } - return err; } diff --git a/arch/cris/arch-v10/drivers/ds1302.c b/arch/cris/arch-v10/drivers/ds1302.c index 1d1936a18133..c9aa3904be05 100644 --- a/arch/cris/arch-v10/drivers/ds1302.c +++ b/arch/cris/arch-v10/drivers/ds1302.c @@ -333,7 +333,7 @@ rtc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, ds1302_writereg(RTC_TRICKLECHARGER, tcs_val); return 0; } - case RTC_VLOW_RD: + case RTC_VL_READ: { /* TODO: * Implement voltage low detection support @@ -342,7 +342,7 @@ rtc_ioctl(struct inode *inode, struct file *file, unsigned int cmd, " is not supported\n"); return 0; } - case RTC_VLOW_SET: + case RTC_VL_CLR: { /* TODO: * Nothing to do since Voltage Low detection is not supported diff --git a/arch/cris/arch-v10/drivers/eeprom.c b/arch/cris/arch-v10/drivers/eeprom.c index be35a70798aa..f1cac9dc75b8 100644 --- a/arch/cris/arch-v10/drivers/eeprom.c +++ b/arch/cris/arch-v10/drivers/eeprom.c @@ -19,77 +19,6 @@ *! Sep 03 1999 Edgar Iglesias Added bail-out stuff if we get interrupted *! in the spin-lock. *! -*! $Log: eeprom.c,v $ -*! Revision 1.12 2005/06/19 17:06:46 starvik -*! Merge of Linux 2.6.12. -*! -*! Revision 1.11 2005/01/26 07:14:46 starvik -*! Applied diff from kernel janitors (Nish Aravamudan). -*! -*! Revision 1.10 2003/09/11 07:29:48 starvik -*! Merge of Linux 2.6.0-test5 -*! -*! Revision 1.9 2003/07/04 08:27:37 starvik -*! Merge of Linux 2.5.74 -*! -*! Revision 1.8 2003/04/09 05:20:47 starvik -*! Merge of Linux 2.5.67 -*! -*! Revision 1.6 2003/02/10 07:19:28 starvik -*! Removed misplaced ; -*! -*! Revision 1.5 2002/12/11 13:13:57 starvik -*! Added arch/ to v10 specific includes -*! Added fix from Linux 2.4 in serial.c (flush_to_flip_buffer) -*! -*! Revision 1.4 2002/11/20 11:56:10 starvik -*! Merge of Linux 2.5.48 -*! -*! Revision 1.3 2002/11/18 13:16:06 starvik -*! Linux 2.5 port of latest 2.4 drivers -*! -*! Revision 1.8 2001/06/15 13:24:29 jonashg -*! * Added verification of pointers from userspace in read and write. -*! * Made busy counter volatile. -*! * Added define for initial write delay. -*! * Removed warnings by using loff_t instead of unsigned long. -*! -*! Revision 1.7 2001/06/14 15:26:54 jonashg -*! Removed test because condition is always true. -*! -*! Revision 1.6 2001/06/14 15:18:20 jonashg -*! Kb -> kB (makes quite a difference if you don't know if you have 2k or 16k). -*! -*! Revision 1.5 2001/06/14 14:39:51 jonashg -*! Forgot to use name when registering the driver. -*! -*! Revision 1.4 2001/06/14 14:35:47 jonashg -*! * Gave driver a name and used it in printk's. -*! * Cleanup. -*! -*! Revision 1.3 2001/03/19 16:04:46 markusl -*! Fixed init of fops struct -*! -*! Revision 1.2 2001/03/19 10:35:07 markusl -*! 2.4 port of eeprom driver -*! -*! Revision 1.8 2000/05/18 10:42:25 edgar -*! Make sure to end write cycle on _every_ write -*! -*! Revision 1.7 2000/01/17 17:41:01 johana -*! Adjusted probing and return -ENOSPC when writing outside EEPROM -*! -*! Revision 1.6 2000/01/17 15:50:36 johana -*! Added adaptive timing adjustments and fixed autoprobing for 2k and 16k(?) -*! EEPROMs -*! -*! Revision 1.5 1999/09/03 15:07:37 edgar -*! Added bail-out check to the spinlock -*! -*! Revision 1.4 1999/09/03 12:11:17 bjornw -*! Proper atomicity (need to use spinlocks, not if's). users -> busy. -*! -*! *! (c) 1999 Axis Communications AB, Lund, Sweden *!*****************************************************************************/ @@ -103,10 +32,10 @@ #include <asm/uaccess.h> #include "i2c.h" -#define D(x) +#define D(x) /* If we should use adaptive timing or not: */ -//#define EEPROM_ADAPTIVE_TIMING +/* #define EEPROM_ADAPTIVE_TIMING */ #define EEPROM_MAJOR_NR 122 /* use a LOCAL/EXPERIMENTAL major for now */ #define EEPROM_MINOR_NR 0 diff --git a/arch/cris/arch-v10/drivers/gpio.c b/arch/cris/arch-v10/drivers/gpio.c index 0d347a705835..68a998bd1069 100644 --- a/arch/cris/arch-v10/drivers/gpio.c +++ b/arch/cris/arch-v10/drivers/gpio.c @@ -1,138 +1,11 @@ -/* $Id: gpio.c,v 1.17 2005/06/19 17:06:46 starvik Exp $ - * +/* * Etrax general port I/O device * - * Copyright (c) 1999, 2000, 2001, 2002 Axis Communications AB + * Copyright (c) 1999-2007 Axis Communications AB * * Authors: Bjorn Wesen (initial version) * Ola Knutsson (LED handling) * Johan Adolfsson (read/set directions, write, port G) - * - * $Log: gpio.c,v $ - * Revision 1.17 2005/06/19 17:06:46 starvik - * Merge of Linux 2.6.12. - * - * Revision 1.16 2005/03/07 13:02:29 starvik - * Protect driver global states with spinlock - * - * Revision 1.15 2005/01/05 06:08:55 starvik - * No need to do local_irq_disable after local_irq_save. - * - * Revision 1.14 2004/12/13 12:21:52 starvik - * Added I/O and DMA allocators from Linux 2.4 - * - * Revision 1.12 2004/08/24 07:19:59 starvik - * Whitespace cleanup - * - * Revision 1.11 2004/05/14 07:58:03 starvik - * Merge of changes from 2.4 - * - * Revision 1.9 2003/09/11 07:29:48 starvik - * Merge of Linux 2.6.0-test5 - * - * Revision 1.8 2003/07/04 08:27:37 starvik - * Merge of Linux 2.5.74 - * - * Revision 1.7 2003/01/10 07:44:07 starvik - * init_ioremap is now called by kernel before drivers are initialized - * - * Revision 1.6 2002/12/11 13:13:57 starvik - * Added arch/ to v10 specific includes - * Added fix from Linux 2.4 in serial.c (flush_to_flip_buffer) - * - * Revision 1.5 2002/11/20 11:56:11 starvik - * Merge of Linux 2.5.48 - * - * Revision 1.4 2002/11/18 10:10:05 starvik - * Linux 2.5 port of latest gpio.c from Linux 2.4 - * - * Revision 1.20 2002/10/16 21:16:24 johana - * Added support for PA high level interrupt. - * That gives 2ms response time with iodtest for high levels and 2-12 ms - * response time on low levels if the check is not made in - * process.c:cpu_idle() as well. - * - * Revision 1.19 2002/10/14 18:27:33 johana - * Implemented alarm handling so select() now works. - * Latency is around 6-9 ms with a etrax_gpio_wake_up_check() in - * cpu_idle(). - * Otherwise I get 15-18 ms (same as doing the poll in userspace - - * but less overhead). - * TODO? Perhaps we should add the check in IMMEDIATE_BH (or whatever it - * is in 2.4) as well? - * TODO? Perhaps call request_irq()/free_irq() only when needed? - * Increased version to 2.5 - * - * Revision 1.18 2002/10/11 15:02:00 johana - * Mask inverted 8 bit value in setget_input(). - * - * Revision 1.17 2002/06/17 15:53:01 johana - * Added IO_READ_INBITS, IO_READ_OUTBITS, IO_SETGET_INPUT and IO_SETGET_OUTPUT - * that take a pointer as argument and thus can handle 32 bit ports (G) - * correctly. - * These should be used instead of IO_READBITS, IO_SETINPUT and IO_SETOUTPUT. - * (especially if Port G bit 31 is used) - * - * Revision 1.16 2002/06/17 09:59:51 johana - * Returning 32 bit values in the ioctl return value doesn't work if bit - * 31 is set (could happen for port G), so mask it of with 0x7FFFFFFF. - * A new set of ioctl's will be added. - * - * Revision 1.15 2002/05/06 13:19:13 johana - * IO_SETINPUT returns mask with bit set = inputs for PA and PB as well. - * - * Revision 1.14 2002/04/12 12:01:53 johana - * Use global r_port_g_data_shadow. - * Moved gpio_init_port_g() closer to gpio_init() and marked it __init. - * - * Revision 1.13 2002/04/10 12:03:55 johana - * Added support for port G /dev/gpiog (minor 3). - * Changed indentation on switch cases. - * Fixed other spaces to tabs. - * - * Revision 1.12 2001/11/12 19:42:15 pkj - * * Corrected return values from gpio_leds_ioctl(). - * * Fixed compiler warnings. - * - * Revision 1.11 2001/10/30 14:39:12 johana - * Added D() around gpio_write printk. - * - * Revision 1.10 2001/10/25 10:24:42 johana - * Added IO_CFG_WRITE_MODE ioctl and write method that can do fast - * bittoggling in the kernel. (This speeds up programming an FPGA with 450kB - * from ~60 seconds to 4 seconds). - * Added save_flags/cli/restore_flags in ioctl. - * - * Revision 1.9 2001/05/04 14:16:07 matsfg - * Corrected spelling error - * - * Revision 1.8 2001/04/27 13:55:26 matsfg - * Moved initioremap. - * Turns off all LEDS on init. - * Added support for shutdown and powerbutton. - * - * Revision 1.7 2001/04/04 13:30:08 matsfg - * Added bitset and bitclear for leds. Calls init_ioremap to set up memmapping - * - * Revision 1.6 2001/03/26 16:03:06 bjornw - * Needs linux/config.h - * - * Revision 1.5 2001/03/26 14:22:03 bjornw - * Namechange of some config options - * - * Revision 1.4 2001/02/27 13:52:48 bjornw - * malloc.h -> slab.h - * - * Revision 1.3 2001/01/24 15:06:48 bjornw - * gpio_wq correct type - * - * Revision 1.2 2001/01/18 16:07:30 bjornw - * 2.4 port - * - * Revision 1.1 2001/01/18 15:55:16 bjornw - * Verbatim copy of etraxgpio.c from elinux 2.0 added - * - * */ @@ -165,7 +38,7 @@ static int dp_cnt; #else #define DP(x) #endif - + static char gpio_name[] = "etrax gpio"; #if 0 @@ -173,9 +46,9 @@ static wait_queue_head_t *gpio_wq; #endif static int gpio_ioctl(struct inode *inode, struct file *file, - unsigned int cmd, unsigned long arg); -static ssize_t gpio_write(struct file * file, const char * buf, size_t count, - loff_t *off); + unsigned int cmd, unsigned long arg); +static ssize_t gpio_write(struct file *file, const char __user *buf, + size_t count, loff_t *off); static int gpio_open(struct inode *inode, struct file *filp); static int gpio_release(struct inode *inode, struct file *filp); static unsigned int gpio_poll(struct file *filp, struct poll_table_struct *wait); @@ -201,22 +74,22 @@ struct gpio_private { /* linked list of alarms to check for */ -static struct gpio_private *alarmlist = 0; +static struct gpio_private *alarmlist; -static int gpio_some_alarms = 0; /* Set if someone uses alarm */ -static unsigned long gpio_pa_irq_enabled_mask = 0; +static int gpio_some_alarms; /* Set if someone uses alarm */ +static unsigned long gpio_pa_irq_enabled_mask; static DEFINE_SPINLOCK(gpio_lock); /* Protect directions etc */ /* Port A and B use 8 bit access, but Port G is 32 bit */ #define NUM_PORTS (GPIO_MINOR_B+1) -static volatile unsigned char *ports[NUM_PORTS] = { - R_PORT_PA_DATA, +static volatile unsigned char *ports[NUM_PORTS] = { + R_PORT_PA_DATA, R_PORT_PB_DATA, }; static volatile unsigned char *shads[NUM_PORTS] = { - &port_pa_data_shadow, + &port_pa_data_shadow, &port_pb_data_shadow }; @@ -236,29 +109,29 @@ static volatile unsigned char *shads[NUM_PORTS] = { #endif -static unsigned char changeable_dir[NUM_PORTS] = { +static unsigned char changeable_dir[NUM_PORTS] = { CONFIG_ETRAX_PA_CHANGEABLE_DIR, - CONFIG_ETRAX_PB_CHANGEABLE_DIR + CONFIG_ETRAX_PB_CHANGEABLE_DIR }; -static unsigned char changeable_bits[NUM_PORTS] = { +static unsigned char changeable_bits[NUM_PORTS] = { CONFIG_ETRAX_PA_CHANGEABLE_BITS, - CONFIG_ETRAX_PB_CHANGEABLE_BITS + CONFIG_ETRAX_PB_CHANGEABLE_BITS }; -static volatile unsigned char *dir[NUM_PORTS] = { - R_PORT_PA_DIR, - R_PORT_PB_DIR +static volatile unsigned char *dir[NUM_PORTS] = { + R_PORT_PA_DIR, + R_PORT_PB_DIR }; static volatile unsigned char *dir_shadow[NUM_PORTS] = { - &port_pa_dir_shadow, - &port_pb_dir_shadow + &port_pa_dir_shadow, + &port_pb_dir_shadow }; /* All bits in port g that can change dir. */ static const unsigned long int changeable_dir_g_mask = 0x01FFFF01; -/* Port G is 32 bit, handle it special, some bits are both inputs +/* Port G is 32 bit, handle it special, some bits are both inputs and outputs at the same time, only some of the bits can change direction and some of them in groups of 8 bit. */ static unsigned long changeable_dir_g; @@ -269,18 +142,17 @@ static unsigned long dir_g_shadow; /* 1=output */ #define USE_PORTS(priv) ((priv)->minor <= GPIO_MINOR_B) - -static unsigned int -gpio_poll(struct file *file, - poll_table *wait) +static unsigned int gpio_poll(struct file *file, poll_table *wait) { unsigned int mask = 0; - struct gpio_private *priv = (struct gpio_private *)file->private_data; + struct gpio_private *priv = file->private_data; unsigned long data; - spin_lock(&gpio_lock); + unsigned long flags; + + spin_lock_irqsave(&gpio_lock, flags); + poll_wait(file, &priv->alarm_wq, wait); if (priv->minor == GPIO_MINOR_A) { - unsigned long flags; unsigned long tmp; data = *R_PORT_PA_DATA; /* PA has support for high level interrupt - @@ -288,27 +160,25 @@ gpio_poll(struct file *file, */ tmp = ~data & priv->highalarm & 0xFF; tmp = (tmp << R_IRQ_MASK1_SET__pa0__BITNR); - local_irq_save(flags); + gpio_pa_irq_enabled_mask |= tmp; *R_IRQ_MASK1_SET = tmp; - local_irq_restore(flags); - } else if (priv->minor == GPIO_MINOR_B) data = *R_PORT_PB_DATA; else if (priv->minor == GPIO_MINOR_G) data = *R_PORT_G_DATA; else { - spin_unlock(&gpio_lock); - return 0; + mask = 0; + goto out; } - + if ((data & priv->highalarm) || (~data & priv->lowalarm)) { mask = POLLIN|POLLRDNORM; } - spin_unlock(&gpio_lock); - +out: + spin_unlock_irqrestore(&gpio_lock, flags); DP(printk("gpio_poll ready: mask 0x%08X\n", mask)); return mask; @@ -316,16 +186,19 @@ gpio_poll(struct file *file, int etrax_gpio_wake_up_check(void) { - struct gpio_private *priv = alarmlist; + struct gpio_private *priv; unsigned long data = 0; int ret = 0; - spin_lock(&gpio_lock); + unsigned long flags; + + spin_lock_irqsave(&gpio_lock, flags); + priv = alarmlist; while (priv) { - if (USE_PORTS(priv)) { + if (USE_PORTS(priv)) data = *priv->port; - } else if (priv->minor == GPIO_MINOR_G) { + else if (priv->minor == GPIO_MINOR_G) data = *R_PORT_G_DATA; - } + if ((data & priv->highalarm) || (~data & priv->lowalarm)) { DP(printk("etrax_gpio_wake_up_check %i\n",priv->minor)); @@ -334,12 +207,12 @@ int etrax_gpio_wake_up_check(void) } priv = priv->next; } - spin_unlock(&gpio_lock); + spin_unlock_irqrestore(&gpio_lock, flags); return ret; } static irqreturn_t -gpio_poll_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs) +gpio_poll_timer_interrupt(int irq, void *dev_id) { if (gpio_some_alarms) { etrax_gpio_wake_up_check(); @@ -349,10 +222,13 @@ gpio_poll_timer_interrupt(int irq, void *dev_id, struct pt_regs *regs) } static irqreturn_t -gpio_pa_interrupt(int irq, void *dev_id, struct pt_regs *regs) +gpio_interrupt(int irq, void *dev_id) { unsigned long tmp; - spin_lock(&gpio_lock); + unsigned long flags; + + spin_lock_irqsave(&gpio_lock, flags); + /* Find what PA interrupts are active */ tmp = (*R_IRQ_READ1); @@ -363,75 +239,70 @@ gpio_pa_interrupt(int irq, void *dev_id, struct pt_regs *regs) *R_IRQ_MASK1_CLR = tmp; gpio_pa_irq_enabled_mask &= ~tmp; - spin_unlock(&gpio_lock); + spin_unlock_irqrestore(&gpio_lock, flags); - if (gpio_some_alarms) { + if (gpio_some_alarms) return IRQ_RETVAL(etrax_gpio_wake_up_check()); - } + return IRQ_NONE; } +static void gpio_write_bit(struct gpio_private *priv, + unsigned char data, int bit) +{ + *priv->port = *priv->shadow &= ~(priv->clk_mask); + if (data & 1 << bit) + *priv->port = *priv->shadow |= priv->data_mask; + else + *priv->port = *priv->shadow &= ~(priv->data_mask); + + /* For FPGA: min 5.0ns (DCC) before CCLK high */ + *priv->port = *priv->shadow |= priv->clk_mask; +} -static ssize_t gpio_write(struct file * file, const char * buf, size_t count, - loff_t *off) +static void gpio_write_byte(struct gpio_private *priv, unsigned char data) { - struct gpio_private *priv = (struct gpio_private *)file->private_data; - unsigned char data, clk_mask, data_mask, write_msb; - unsigned long flags; + int i; - spin_lock(&gpio_lock); + if (priv->write_msb) + for (i = 7; i >= 0; i--) + gpio_write_bit(priv, data, i); + else + for (i = 0; i <= 7; i++) + gpio_write_bit(priv, data, i); +} +static ssize_t gpio_write(struct file *file, const char __user *buf, + size_t count, loff_t *off) +{ + struct gpio_private *priv = file->private_data; + unsigned long flags; ssize_t retval = count; - if (priv->minor !=GPIO_MINOR_A && priv->minor != GPIO_MINOR_B) { - retval = -EFAULT; - goto out; - } - - if (!access_ok(VERIFY_READ, buf, count)) { - retval = -EFAULT; - goto out; - } - clk_mask = priv->clk_mask; - data_mask = priv->data_mask; + + if (priv->minor != GPIO_MINOR_A && priv->minor != GPIO_MINOR_B) + return -EFAULT; + + if (!access_ok(VERIFY_READ, buf, count)) + return -EFAULT; + + spin_lock_irqsave(&gpio_lock, flags); + /* It must have been configured using the IO_CFG_WRITE_MODE */ /* Perhaps a better error code? */ - if (clk_mask == 0 || data_mask == 0) { + if (priv->clk_mask == 0 || priv->data_mask == 0) { retval = -EPERM; goto out; } - write_msb = priv->write_msb; - D(printk("gpio_write: %lu to data 0x%02X clk 0x%02X msb: %i\n",count, data_mask, clk_mask, write_msb)); - while (count--) { - int i; - data = *buf++; - if (priv->write_msb) { - for (i = 7; i >= 0;i--) { - local_irq_save(flags); - *priv->port = *priv->shadow &= ~clk_mask; - if (data & 1<<i) - *priv->port = *priv->shadow |= data_mask; - else - *priv->port = *priv->shadow &= ~data_mask; - /* For FPGA: min 5.0ns (DCC) before CCLK high */ - *priv->port = *priv->shadow |= clk_mask; - local_irq_restore(flags); - } - } else { - for (i = 0; i <= 7;i++) { - local_irq_save(flags); - *priv->port = *priv->shadow &= ~clk_mask; - if (data & 1<<i) - *priv->port = *priv->shadow |= data_mask; - else - *priv->port = *priv->shadow &= ~data_mask; - /* For FPGA: min 5.0ns (DCC) before CCLK high */ - *priv->port = *priv->shadow |= clk_mask; - local_irq_restore(flags); - } - } - } + + D(printk(KERN_DEBUG "gpio_write: %02X to data 0x%02X " + "clk 0x%02X msb: %i\n", + count, priv->data_mask, priv->clk_mask, priv->write_msb)); + + while (count--) + gpio_write_byte(priv, *buf++); + out: - spin_unlock(&gpio_lock); + spin_unlock_irqrestore(&gpio_lock, flags); return retval; } @@ -442,22 +313,20 @@ gpio_open(struct inode *inode, struct file *filp) { struct gpio_private *priv; int p = iminor(inode); + unsigned long flags; if (p > GPIO_MINOR_LAST) return -EINVAL; - priv = kmalloc(sizeof(struct gpio_private), - GFP_KERNEL); + priv = kzalloc(sizeof(struct gpio_private), GFP_KERNEL); if (!priv) return -ENOMEM; priv->minor = p; - /* initialize the io/alarm struct and link it into our alarmlist */ + /* initialize the io/alarm struct */ - priv->next = alarmlist; - alarmlist = priv; if (USE_PORTS(priv)) { /* A and B */ priv->port = ports[p]; priv->shadow = shads[p]; @@ -480,7 +349,13 @@ gpio_open(struct inode *inode, struct file *filp) priv->data_mask = 0; init_waitqueue_head(&priv->alarm_wq); - filp->private_data = (void *)priv; + filp->private_data = priv; + + /* link it into our alarmlist */ + spin_lock_irqsave(&gpio_lock, flags); + priv->next = alarmlist; + alarmlist = priv; + spin_unlock_irqrestore(&gpio_lock, flags); return 0; } @@ -490,11 +365,12 @@ gpio_release(struct inode *inode, struct file *filp) { struct gpio_private *p; struct gpio_private *todel; + unsigned long flags; - spin_lock(&gpio_lock); + spin_lock_irqsave(&gpio_lock, flags); - p = alarmlist; - todel = (struct gpio_private *)filp->private_data; + p = alarmlist; + todel = filp->private_data; /* unlink from alarmlist and free the private structure */ @@ -512,123 +388,114 @@ gpio_release(struct inode *inode, struct file *filp) while (p) { if (p->highalarm | p->lowalarm) { gpio_some_alarms = 1; - spin_unlock(&gpio_lock); - return 0; + goto out; } p = p->next; } gpio_some_alarms = 0; - spin_unlock(&gpio_lock); +out: + spin_unlock_irqrestore(&gpio_lock, flags); return 0; } -/* Main device API. ioctl's to read/set/clear bits, as well as to +/* Main device API. ioctl's to read/set/clear bits, as well as to * set alarms to wait for using a subsequent select(). */ - unsigned long inline setget_input(struct gpio_private *priv, unsigned long arg) { - /* Set direction 0=unchanged 1=input, - * return mask with 1=input - */ - unsigned long flags; + /* Set direction 0=unchanged 1=input, + * return mask with 1=input */ if (USE_PORTS(priv)) { - local_irq_save(flags); - *priv->dir = *priv->dir_shadow &= + *priv->dir = *priv->dir_shadow &= ~((unsigned char)arg & priv->changeable_dir); - local_irq_restore(flags); return ~(*priv->dir_shadow) & 0xFF; /* Only 8 bits */ - } else if (priv->minor == GPIO_MINOR_G) { - /* We must fiddle with R_GEN_CONFIG to change dir */ - local_irq_save(flags); - if (((arg & dir_g_in_bits) != arg) && - (arg & changeable_dir_g)) { - arg &= changeable_dir_g; - /* Clear bits in genconfig to set to input */ - if (arg & (1<<0)) { - genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG,g0dir); - dir_g_in_bits |= (1<<0); - dir_g_out_bits &= ~(1<<0); - } - if ((arg & 0x0000FF00) == 0x0000FF00) { - genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG,g8_15dir); - dir_g_in_bits |= 0x0000FF00; - dir_g_out_bits &= ~0x0000FF00; - } - if ((arg & 0x00FF0000) == 0x00FF0000) { - genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG,g16_23dir); - dir_g_in_bits |= 0x00FF0000; - dir_g_out_bits &= ~0x00FF0000; - } - if (arg & (1<<24)) { - genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG,g24dir); - dir_g_in_bits |= (1<<24); - dir_g_out_bits &= ~(1<<24); - } - D(printk(KERN_INFO "gpio: SETINPUT on port G set " - "genconfig to 0x%08lX " - "in_bits: 0x%08lX " - "out_bits: 0x%08lX\n", - (unsigned long)genconfig_shadow, - dir_g_in_bits, dir_g_out_bits)); - *R_GEN_CONFIG = genconfig_shadow; - /* Must be a >120 ns delay before writing this again */ - + } + + if (priv->minor != GPIO_MINOR_G) + return 0; + + /* We must fiddle with R_GEN_CONFIG to change dir */ + if (((arg & dir_g_in_bits) != arg) && + (arg & changeable_dir_g)) { + arg &= changeable_dir_g; + /* Clear bits in genconfig to set to input */ + if (arg & (1<<0)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, g0dir); + dir_g_in_bits |= (1<<0); + dir_g_out_bits &= ~(1<<0); } - local_irq_restore(flags); - return dir_g_in_bits; + if ((arg & 0x0000FF00) == 0x0000FF00) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, g8_15dir); + dir_g_in_bits |= 0x0000FF00; + dir_g_out_bits &= ~0x0000FF00; + } + if ((arg & 0x00FF0000) == 0x00FF0000) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, g16_23dir); + dir_g_in_bits |= 0x00FF0000; + dir_g_out_bits &= ~0x00FF0000; + } + if (arg & (1<<24)) { + genconfig_shadow &= ~IO_MASK(R_GEN_CONFIG, g24dir); + dir_g_in_bits |= (1<<24); + dir_g_out_bits &= ~(1<<24); + } + D(printk(KERN_DEBUG "gpio: SETINPUT on port G set " + "genconfig to 0x%08lX " + "in_bits: 0x%08lX " + "out_bits: 0x%08lX\n", + (unsigned long)genconfig_shadow, + dir_g_in_bits, dir_g_out_bits)); + *R_GEN_CONFIG = genconfig_shadow; + /* Must be a >120 ns delay before writing this again */ + } - return 0; + return dir_g_in_bits; } /* setget_input */ unsigned long inline setget_output(struct gpio_private *priv, unsigned long arg) { - unsigned long flags; if (USE_PORTS(priv)) { - local_irq_save(flags); - *priv->dir = *priv->dir_shadow |= - ((unsigned char)arg & priv->changeable_dir); - local_irq_restore(flags); + *priv->dir = *priv->dir_shadow |= + ((unsigned char)arg & priv->changeable_dir); return *priv->dir_shadow; - } else if (priv->minor == GPIO_MINOR_G) { - /* We must fiddle with R_GEN_CONFIG to change dir */ - local_irq_save(flags); - if (((arg & dir_g_out_bits) != arg) && - (arg & changeable_dir_g)) { - /* Set bits in genconfig to set to output */ - if (arg & (1<<0)) { - genconfig_shadow |= IO_MASK(R_GEN_CONFIG,g0dir); - dir_g_out_bits |= (1<<0); - dir_g_in_bits &= ~(1<<0); - } - if ((arg & 0x0000FF00) == 0x0000FF00) { - genconfig_shadow |= IO_MASK(R_GEN_CONFIG,g8_15dir); - dir_g_out_bits |= 0x0000FF00; - dir_g_in_bits &= ~0x0000FF00; - } - if ((arg & 0x00FF0000) == 0x00FF0000) { - genconfig_shadow |= IO_MASK(R_GEN_CONFIG,g16_23dir); - dir_g_out_bits |= 0x00FF0000; - dir_g_in_bits &= ~0x00FF0000; - } - if (arg & (1<<24)) { - genconfig_shadow |= IO_MASK(R_GEN_CONFIG,g24dir); - dir_g_out_bits |= (1<<24); - dir_g_in_bits &= ~(1<<24); - } - D(printk(KERN_INFO "gpio: SETOUTPUT on port G set " - "genconfig to 0x%08lX " - "in_bits: 0x%08lX " - "out_bits: 0x%08lX\n", - (unsigned long)genconfig_shadow, - dir_g_in_bits, dir_g_out_bits)); - *R_GEN_CONFIG = genconfig_shadow; - /* Must be a >120 ns delay before writing this again */ + } + if (priv->minor != GPIO_MINOR_G) + return 0; + + /* We must fiddle with R_GEN_CONFIG to change dir */ + if (((arg & dir_g_out_bits) != arg) && + (arg & changeable_dir_g)) { + /* Set bits in genconfig to set to output */ + if (arg & (1<<0)) { + genconfig_shadow |= IO_MASK(R_GEN_CONFIG, g0dir); + dir_g_out_bits |= (1<<0); + dir_g_in_bits &= ~(1<<0); } - local_irq_restore(flags); - return dir_g_out_bits & 0x7FFFFFFF; + if ((arg & 0x0000FF00) == 0x0000FF00) { + genconfig_shadow |= IO_MASK(R_GEN_CONFIG, g8_15dir); + dir_g_out_bits |= 0x0000FF00; + dir_g_in_bits &= ~0x0000FF00; + } + if ((arg & 0x00FF0000) == 0x00FF0000) { + genconfig_shadow |= IO_MASK(R_GEN_CONFIG, g16_23dir); + dir_g_out_bits |= 0x00FF0000; + dir_g_in_bits &= ~0x00FF0000; + } + if (arg & (1<<24)) { + genconfig_shadow |= IO_MASK(R_GEN_CONFIG, g24dir); + dir_g_out_bits |= (1<<24); + dir_g_in_bits &= ~(1<<24); + } + D(printk(KERN_INFO "gpio: SETOUTPUT on port G set " + "genconfig to 0x%08lX " + "in_bits: 0x%08lX " + "out_bits: 0x%08lX\n", + (unsigned long)genconfig_shadow, + dir_g_in_bits, dir_g_out_bits)); + *R_GEN_CONFIG = genconfig_shadow; + /* Must be a >120 ns delay before writing this again */ } - return 0; + return dir_g_out_bits & 0x7FFFFFFF; } /* setget_output */ static int @@ -642,12 +509,11 @@ gpio_ioctl(struct inode *inode, struct file *file, unsigned long val; int ret = 0; - struct gpio_private *priv = (struct gpio_private *)file->private_data; - if (_IOC_TYPE(cmd) != ETRAXGPIO_IOCTYPE) { + struct gpio_private *priv = file->private_data; + if (_IOC_TYPE(cmd) != ETRAXGPIO_IOCTYPE) return -EINVAL; - } - spin_lock(&gpio_lock); + spin_lock_irqsave(&gpio_lock, flags); switch (_IOC_NR(cmd)) { case IO_READBITS: /* Use IO_READ_INBITS and IO_READ_OUTBITS instead */ @@ -659,7 +525,6 @@ gpio_ioctl(struct inode *inode, struct file *file, } break; case IO_SETBITS: - local_irq_save(flags); // set changeable bits with a 1 in arg if (USE_PORTS(priv)) { *priv->port = *priv->shadow |= @@ -667,10 +532,8 @@ gpio_ioctl(struct inode *inode, struct file *file, } else if (priv->minor == GPIO_MINOR_G) { *R_PORT_G_DATA = port_g_data_shadow |= (arg & dir_g_out_bits); } - local_irq_restore(flags); break; case IO_CLRBITS: - local_irq_save(flags); // clear changeable bits with a 1 in arg if (USE_PORTS(priv)) { *priv->port = *priv->shadow &= @@ -678,7 +541,6 @@ gpio_ioctl(struct inode *inode, struct file *file, } else if (priv->minor == GPIO_MINOR_G) { *R_PORT_G_DATA = port_g_data_shadow &= ~((unsigned long)arg & dir_g_out_bits); } - local_irq_restore(flags); break; case IO_HIGHALARM: // set alarm when bits with 1 in arg go high @@ -698,6 +560,8 @@ gpio_ioctl(struct inode *inode, struct file *file, /* Must update gpio_some_alarms */ struct gpio_private *p = alarmlist; int some_alarms; + spin_lock_irq(&gpio_lock); + p = alarmlist; some_alarms = 0; while (p) { if (p->highalarm | p->lowalarm) { @@ -707,6 +571,7 @@ gpio_ioctl(struct inode *inode, struct file *file, p = p->next; } gpio_some_alarms = some_alarms; + spin_unlock_irq(&gpio_lock); } break; case IO_READDIR: /* Use IO_SETGET_INPUT/OUTPUT instead! */ @@ -766,7 +631,7 @@ gpio_ioctl(struct inode *inode, struct file *file, } else if (priv->minor == GPIO_MINOR_G) { val = *R_PORT_G_DATA; } - if (copy_to_user((unsigned long*)arg, &val, sizeof(val))) + if (copy_to_user((void __user *)arg, &val, sizeof(val))) ret = -EFAULT; break; case IO_READ_OUTBITS: @@ -776,33 +641,32 @@ gpio_ioctl(struct inode *inode, struct file *file, } else if (priv->minor == GPIO_MINOR_G) { val = port_g_data_shadow; } - if (copy_to_user((unsigned long*)arg, &val, sizeof(val))) + if (copy_to_user((void __user *)arg, &val, sizeof(val))) ret = -EFAULT; break; case IO_SETGET_INPUT: /* bits set in *arg is set to input, * *arg updated with current input pins. */ - if (copy_from_user(&val, (unsigned long*)arg, sizeof(val))) + if (copy_from_user(&val, (void __user *)arg, sizeof(val))) { ret = -EFAULT; break; } val = setget_input(priv, val); - if (copy_to_user((unsigned long*)arg, &val, sizeof(val))) + if (copy_to_user((void __user *)arg, &val, sizeof(val))) ret = -EFAULT; break; case IO_SETGET_OUTPUT: /* bits set in *arg is set to output, * *arg updated with current output pins. */ - if (copy_from_user(&val, (unsigned long*)arg, sizeof(val))) - { + if (copy_from_user(&val, (void __user *)arg, sizeof(val))) { ret = -EFAULT; break; } val = setget_output(priv, val); - if (copy_to_user((unsigned long*)arg, &val, sizeof(val))) + if (copy_to_user((void __user *)arg, &val, sizeof(val))) ret = -EFAULT; break; default: @@ -812,7 +676,7 @@ gpio_ioctl(struct inode *inode, struct file *file, ret = -EINVAL; } /* switch */ - spin_unlock(&gpio_lock); + spin_unlock_irqrestore(&gpio_lock, flags); return ret; } @@ -824,18 +688,18 @@ gpio_leds_ioctl(unsigned int cmd, unsigned long arg) switch (_IOC_NR(cmd)) { case IO_LEDACTIVE_SET: - green = ((unsigned char) arg) & 1; - red = (((unsigned char) arg) >> 1) & 1; - LED_ACTIVE_SET_G(green); - LED_ACTIVE_SET_R(red); + green = ((unsigned char)arg) & 1; + red = (((unsigned char)arg) >> 1) & 1; + CRIS_LED_ACTIVE_SET_G(green); + CRIS_LED_ACTIVE_SET_R(red); break; case IO_LED_SETBIT: - LED_BIT_SET(arg); + CRIS_LED_BIT_SET(arg); break; case IO_LED_CLRBIT: - LED_BIT_CLR(arg); + CRIS_LED_BIT_CLR(arg); break; default: @@ -845,7 +709,7 @@ gpio_leds_ioctl(unsigned int cmd, unsigned long arg) return 0; } -const struct file_operations gpio_fops = { +static const struct file_operations gpio_fops = { .owner = THIS_MODULE, .poll = gpio_poll, .ioctl = gpio_ioctl, @@ -854,16 +718,18 @@ const struct file_operations gpio_fops = { .release = gpio_release, }; - -void ioif_watcher(const unsigned int gpio_in_available, - const unsigned int gpio_out_available, - const unsigned char pa_available, - const unsigned char pb_available) +static void ioif_watcher(const unsigned int gpio_in_available, + const unsigned int gpio_out_available, + const unsigned char pa_available, + const unsigned char pb_available) { unsigned long int flags; - D(printk("gpio.c: ioif_watcher called\n")); - D(printk("gpio.c: G in: 0x%08x G out: 0x%08x PA: 0x%02x PB: 0x%02x\n", - gpio_in_available, gpio_out_available, pa_available, pb_available)); + + D(printk(KERN_DEBUG "gpio.c: ioif_watcher called\n")); + D(printk(KERN_DEBUG "gpio.c: G in: 0x%08x G out: 0x%08x " + "PA: 0x%02x PB: 0x%02x\n", + gpio_in_available, gpio_out_available, + pa_available, pb_available)); spin_lock_irqsave(&gpio_lock, flags); @@ -872,7 +738,7 @@ void ioif_watcher(const unsigned int gpio_in_available, /* Initialise the dir_g_shadow etc. depending on genconfig */ /* 0=input 1=output */ - if (genconfig_shadow & IO_STATE(R_GEN_CONFIG, g0dir, out)) + if (genconfig_shadow & IO_STATE(R_GEN_CONFIG, g0dir, out)) dir_g_shadow |= (1 << 0); if (genconfig_shadow & IO_STATE(R_GEN_CONFIG, g8_15dir, out)) dir_g_shadow |= 0x0000FF00; @@ -884,7 +750,8 @@ void ioif_watcher(const unsigned int gpio_in_available, changeable_dir_g = changeable_dir_g_mask; changeable_dir_g &= dir_g_out_bits; changeable_dir_g &= dir_g_in_bits; - /* Correct the bits that can change direction */ + + /* Correct the bits that can change direction */ dir_g_out_bits &= ~changeable_dir_g; dir_g_out_bits |= dir_g_shadow; dir_g_in_bits &= ~changeable_dir_g; @@ -892,7 +759,8 @@ void ioif_watcher(const unsigned int gpio_in_available, spin_unlock_irqrestore(&gpio_lock, flags); - printk(KERN_INFO "GPIO port G: in_bits: 0x%08lX out_bits: 0x%08lX val: %08lX\n", + printk(KERN_INFO "GPIO port G: in_bits: 0x%08lX out_bits: 0x%08lX " + "val: %08lX\n", dir_g_in_bits, dir_g_out_bits, (unsigned long)*R_PORT_G_DATA); printk(KERN_INFO "GPIO port G: dir: %08lX changeable: %08lX\n", dir_g_shadow, changeable_dir_g); @@ -900,16 +768,12 @@ void ioif_watcher(const unsigned int gpio_in_available, /* main driver initialization routine, called from mem.c */ -static __init int -gpio_init(void) +static int __init gpio_init(void) { int res; #if defined (CONFIG_ETRAX_CSP0_LEDS) int i; #endif - printk("gpio init\n"); - - /* do the formalities */ res = register_chrdev(GPIO_MAJOR, gpio_name, &gpio_fops); if (res < 0) { @@ -919,43 +783,45 @@ gpio_init(void) /* Clear all leds */ #if defined (CONFIG_ETRAX_CSP0_LEDS) || defined (CONFIG_ETRAX_PA_LEDS) || defined (CONFIG_ETRAX_PB_LEDS) - LED_NETWORK_SET(0); - LED_ACTIVE_SET(0); - LED_DISK_READ(0); - LED_DISK_WRITE(0); + CRIS_LED_NETWORK_SET(0); + CRIS_LED_ACTIVE_SET(0); + CRIS_LED_DISK_READ(0); + CRIS_LED_DISK_WRITE(0); #if defined (CONFIG_ETRAX_CSP0_LEDS) - for (i = 0; i < 32; i++) { - LED_BIT_SET(i); - } + for (i = 0; i < 32; i++) + CRIS_LED_BIT_SET(i); #endif #endif /* The I/O interface allocation watcher will be called when * registering it. */ if (cris_io_interface_register_watcher(ioif_watcher)){ - printk(KERN_WARNING "gpio_init: Failed to install IO if allocator watcher\n"); + printk(KERN_WARNING "gpio_init: Failed to install IO " + "if allocator watcher\n"); } - printk(KERN_INFO "ETRAX 100LX GPIO driver v2.5, (c) 2001, 2002, 2003, 2004 Axis Communications AB\n"); + printk(KERN_INFO "ETRAX 100LX GPIO driver v2.5, (c) 2001-2008 " + "Axis Communications AB\n"); /* We call etrax_gpio_wake_up_check() from timer interrupt and * from cpu_idle() in kernel/process.c * The check in cpu_idle() reduces latency from ~15 ms to ~6 ms * in some tests. - */ - if (request_irq(TIMER0_IRQ_NBR, gpio_poll_timer_interrupt, - IRQF_SHARED | IRQF_DISABLED,"gpio poll", NULL)) { + */ + res = request_irq(TIMER0_IRQ_NBR, gpio_poll_timer_interrupt, + IRQF_SHARED | IRQF_DISABLED, "gpio poll", gpio_name); + if (res) { printk(KERN_CRIT "err: timer0 irq for gpio\n"); + return res; } - if (request_irq(PA_IRQ_NBR, gpio_pa_interrupt, - IRQF_SHARED | IRQF_DISABLED,"gpio PA", NULL)) { + res = request_irq(PA_IRQ_NBR, gpio_interrupt, + IRQF_SHARED | IRQF_DISABLED, "gpio PA", gpio_name); + if (res) printk(KERN_CRIT "err: PA irq for gpio\n"); - } - return res; } /* this makes sure that gpio_init is called during kernel boot */ - module_init(gpio_init); + diff --git a/arch/cris/arch-v10/drivers/i2c.c b/arch/cris/arch-v10/drivers/i2c.c index aca81ddaf60f..d6d22067d0c8 100644 --- a/arch/cris/arch-v10/drivers/i2c.c +++ b/arch/cris/arch-v10/drivers/i2c.c @@ -6,85 +6,9 @@ *! kernel modules (i2c_writereg/readreg) and from userspace using *! ioctl()'s *! -*! Nov 30 1998 Torbjorn Eliasson Initial version. -*! Bjorn Wesen Elinux kernel version. -*! Jan 14 2000 Johan Adolfsson Fixed PB shadow register stuff - -*! don't use PB_I2C if DS1302 uses same bits, -*! use PB. -*! $Log: i2c.c,v $ -*! Revision 1.13 2005/03/07 13:13:07 starvik -*! Added spinlocks to protect states etc -*! -*! Revision 1.12 2005/01/05 06:11:22 starvik -*! No need to do local_irq_disable after local_irq_save. -*! -*! Revision 1.11 2004/12/13 12:21:52 starvik -*! Added I/O and DMA allocators from Linux 2.4 -*! -*! Revision 1.9 2004/08/24 06:49:14 starvik -*! Whitespace cleanup -*! -*! Revision 1.8 2004/06/08 08:48:26 starvik -*! Removed unused code -*! -*! Revision 1.7 2004/05/28 09:26:59 starvik -*! Modified I2C initialization to work in 2.6. -*! -*! Revision 1.6 2004/05/14 07:58:03 starvik -*! Merge of changes from 2.4 -*! -*! Revision 1.4 2002/12/11 13:13:57 starvik -*! Added arch/ to v10 specific includes -*! Added fix from Linux 2.4 in serial.c (flush_to_flip_buffer) -*! -*! Revision 1.3 2002/11/20 11:56:11 starvik -*! Merge of Linux 2.5.48 -*! -*! Revision 1.2 2002/11/18 13:16:06 starvik -*! Linux 2.5 port of latest 2.4 drivers -*! -*! Revision 1.9 2002/10/31 15:32:26 starvik -*! Update Port B register and shadow even when running with hardware support -*! to avoid glitches when reading bits -*! Never set direction to out in i2c_inbyte -*! Removed incorrect clock toggling at end of i2c_inbyte -*! -*! Revision 1.8 2002/08/13 06:31:53 starvik -*! Made SDA and SCL line configurable -*! Modified i2c_inbyte to work with PCF8563 -*! -*! Revision 1.7 2001/04/04 13:11:36 markusl -*! Updated according to review remarks -*! -*! Revision 1.6 2001/03/19 12:43:00 markusl -*! Made some symbols unstatic (used by the eeprom driver) -*! -*! Revision 1.5 2001/02/27 13:52:48 bjornw -*! malloc.h -> slab.h -*! -*! Revision 1.4 2001/02/15 07:17:40 starvik -*! Corrected usage if port_pb_i2c_shadow -*! -*! Revision 1.3 2001/01/26 17:55:13 bjornw -*! * Made I2C_USES_PB_NOT_PB_I2C a CONFIG option instead of assigning it -*! magically. Config.in needs to set it for the options that need it, like -*! Dallas 1302 support. Actually, it should be default since it screws up -*! the PB bits even if you don't use I2C.. -*! * Include linux/config.h to get the above -*! -*! Revision 1.2 2001/01/18 15:49:30 bjornw -*! 2.4 port of I2C including some cleanups (untested of course) -*! -*! Revision 1.1 2001/01/18 15:35:25 bjornw -*! Verbatim copy of the Etrax i2c driver, 2.0 elinux version -*! -*! -*! --------------------------------------------------------------------------- -*! -*! (C) Copyright 1999-2002 Axis Communications AB, LUND, SWEDEN +*! (C) Copyright 1999-2007 Axis Communications AB, LUND, SWEDEN *! *!***************************************************************************/ -/* $Id: i2c.c,v 1.13 2005/03/07 13:13:07 starvik Exp $ */ /****************** INCLUDE FILES SECTION ***********************************/ @@ -622,7 +546,7 @@ i2c_readreg(unsigned char theSlave, unsigned char theReg) * last received byte needs to be nacked * instead of acked */ - i2c_sendack(); + i2c_sendnack(); /* * end sequence */ @@ -708,6 +632,7 @@ i2c_init(void) if (!first) { return res; } + first = 0; /* Setup and enable the Port B I2C interface */ diff --git a/arch/cris/arch-v10/drivers/pcf8563.c b/arch/cris/arch-v10/drivers/pcf8563.c index c263b8232dbc..52103d16dc6c 100644 --- a/arch/cris/arch-v10/drivers/pcf8563.c +++ b/arch/cris/arch-v10/drivers/pcf8563.c @@ -8,14 +8,13 @@ * low detector are also provided. All address and data are transferred * serially via two-line bidirectional I2C-bus. Maximum bus speed is * 400 kbits/s. The built-in word address register is incremented - * automatically after each written or read bute. + * automatically after each written or read byte. * - * Copyright (c) 2002, Axis Communications AB + * Copyright (c) 2002-2007, Axis Communications AB * All rights reserved. * * Author: Tobias Anderberg <tobiasa@axis.com>. * - * $Id: pcf8563.c,v 1.11 2005/03/07 13:13:07 starvik Exp $ */ #include <linux/module.h> @@ -27,19 +26,19 @@ #include <linux/ioctl.h> #include <linux/delay.h> #include <linux/bcd.h> -#include <linux/capability.h> +#include <linux/mutex.h> #include <asm/uaccess.h> #include <asm/system.h> #include <asm/io.h> -#include <asm/arch/svinto.h> #include <asm/rtc.h> + #include "i2c.h" -#define PCF8563_MAJOR 121 /* Local major number. */ -#define DEVICE_NAME "rtc" /* Name which is registered in /proc/devices. */ +#define PCF8563_MAJOR 121 /* Local major number. */ +#define DEVICE_NAME "rtc" /* Name which is registered in /proc/devices. */ #define PCF8563_NAME "PCF8563" -#define DRIVER_VERSION "$Revision: 1.11 $" +#define DRIVER_VERSION "$Revision: 1.24 $" /* I2C bus slave registers. */ #define RTC_I2C_READ 0xa3 @@ -49,71 +48,88 @@ #define rtc_read(x) i2c_readreg(RTC_I2C_READ, x) #define rtc_write(x,y) i2c_writereg(RTC_I2C_WRITE, x, y) -static DEFINE_SPINLOCK(rtc_lock); /* Protect state etc */ - +static DEFINE_MUTEX(rtc_lock); /* Protect state etc */ + static const unsigned char days_in_month[] = { 0, 31, 28, 31, 30, 31, 30, 31, 31, 30, 31, 30, 31 }; int pcf8563_ioctl(struct inode *, struct file *, unsigned int, unsigned long); +/* Cache VL bit value read at driver init since writing the RTC_SECOND + * register clears the VL status. + */ +static int voltage_low; + static const struct file_operations pcf8563_fops = { .owner = THIS_MODULE, .ioctl = pcf8563_ioctl, }; unsigned char -pcf8563_readreg(int reg) +pcf8563_readreg(int reg) { - unsigned char res = i2c_readreg(RTC_I2C_READ, reg); - - /* The PCF8563 does not return 0 for unimplemented bits */ - switch(reg) - { - case RTC_SECONDS: - case RTC_MINUTES: - res &= 0x7f; - break; - case RTC_HOURS: - case RTC_DAY_OF_MONTH: - res &= 0x3f; - break; - case RTC_MONTH: - res = (res & 0x1f) - 1; /* PCF8563 returns month in range 1-12 */ - break; + unsigned char res = rtc_read(reg); + + /* The PCF8563 does not return 0 for unimplemented bits. */ + switch (reg) { + case RTC_SECONDS: + case RTC_MINUTES: + res &= 0x7F; + break; + case RTC_HOURS: + case RTC_DAY_OF_MONTH: + res &= 0x3F; + break; + case RTC_WEEKDAY: + res &= 0x07; + break; + case RTC_MONTH: + res &= 0x1F; + break; + case RTC_CONTROL1: + res &= 0xA8; + break; + case RTC_CONTROL2: + res &= 0x1F; + break; + case RTC_CLOCKOUT_FREQ: + case RTC_TIMER_CONTROL: + res &= 0x83; + break; } return res; } void -pcf8563_writereg(int reg, unsigned char val) +pcf8563_writereg(int reg, unsigned char val) { -#ifdef CONFIG_ETRAX_RTC_READONLY - if (reg == RTC_CONTROL1 || (reg >= RTC_SECONDS && reg <= RTC_YEAR)) - return; -#endif - rtc_write(reg, val); } void get_rtc_time(struct rtc_time *tm) { - tm->tm_sec = rtc_read(RTC_SECONDS); - tm->tm_min = rtc_read(RTC_MINUTES); + tm->tm_sec = rtc_read(RTC_SECONDS); + tm->tm_min = rtc_read(RTC_MINUTES); tm->tm_hour = rtc_read(RTC_HOURS); tm->tm_mday = rtc_read(RTC_DAY_OF_MONTH); - tm->tm_mon = rtc_read(RTC_MONTH); + tm->tm_wday = rtc_read(RTC_WEEKDAY); + tm->tm_mon = rtc_read(RTC_MONTH); tm->tm_year = rtc_read(RTC_YEAR); - if (tm->tm_sec & 0x80) - printk(KERN_WARNING "%s: RTC Low Voltage - date/time is not reliable!\n", PCF8563_NAME); + if (tm->tm_sec & 0x80) { + printk(KERN_ERR "%s: RTC Voltage Low - reliable date/time " + "information is no longer guaranteed!\n", PCF8563_NAME); + } - tm->tm_year = BCD_TO_BIN(tm->tm_year) + ((tm->tm_mon & 0x80) ? 100 : 0); - tm->tm_sec &= 0x7f; - tm->tm_min &= 0x7f; - tm->tm_hour &= 0x3f; - tm->tm_mday &= 0x3f; - tm->tm_mon &= 0x1f; + tm->tm_year = BCD_TO_BIN(tm->tm_year) + + ((tm->tm_mon & 0x80) ? 100 : 0); + tm->tm_sec &= 0x7F; + tm->tm_min &= 0x7F; + tm->tm_hour &= 0x3F; + tm->tm_mday &= 0x3F; + tm->tm_wday &= 0x07; /* Not coded in BCD. */ + tm->tm_mon &= 0x1F; BCD_TO_BIN(tm->tm_sec); BCD_TO_BIN(tm->tm_min); @@ -126,17 +142,24 @@ get_rtc_time(struct rtc_time *tm) int __init pcf8563_init(void) { - int ret; - - if ((ret = i2c_init())) { - printk(KERN_CRIT "pcf8563_init: failed to init i2c\n"); - return ret; + static int res; + static int first = 1; + + if (!first) + return res; + first = 0; + + /* Initiate the i2c protocol. */ + res = i2c_init(); + if (res < 0) { + printk(KERN_CRIT "pcf8563_init: Failed to init i2c.\n"); + return res; } /* * First of all we need to reset the chip. This is done by - * clearing control1, control2 and clk freq, clear the - * Voltage Low bit, and resetting all alarms. + * clearing control1, control2 and clk freq and resetting + * all alarms. */ if (rtc_write(RTC_CONTROL1, 0x00) < 0) goto err; @@ -147,34 +170,36 @@ pcf8563_init(void) if (rtc_write(RTC_CLOCKOUT_FREQ, 0x00) < 0) goto err; - /* Clear the VL bit in the seconds register. */ - ret = rtc_read(RTC_SECONDS); - - if (rtc_write(RTC_SECONDS, (ret & 0x7f)) < 0) + if (rtc_write(RTC_TIMER_CONTROL, 0x03) < 0) goto err; - + /* Reset the alarms. */ - if (rtc_write(RTC_MINUTE_ALARM, 0x00) < 0) + if (rtc_write(RTC_MINUTE_ALARM, 0x80) < 0) goto err; - - if (rtc_write(RTC_HOUR_ALARM, 0x00) < 0) + + if (rtc_write(RTC_HOUR_ALARM, 0x80) < 0) goto err; - - if (rtc_write(RTC_DAY_ALARM, 0x00) < 0) + + if (rtc_write(RTC_DAY_ALARM, 0x80) < 0) goto err; - - if (rtc_write(RTC_WEEKDAY_ALARM, 0x00) < 0) + + if (rtc_write(RTC_WEEKDAY_ALARM, 0x80) < 0) goto err; - - /* Check for low voltage, and warn about it.. */ - if (rtc_read(RTC_SECONDS) & 0x80) - printk(KERN_WARNING "%s: RTC Low Voltage - date/time is not reliable!\n", PCF8563_NAME); - - return 0; + + /* Check for low voltage, and warn about it. */ + if (rtc_read(RTC_SECONDS) & 0x80) { + voltage_low = 1; + printk(KERN_WARNING "%s: RTC Voltage Low - reliable " + "date/time information is no longer guaranteed!\n", + PCF8563_NAME); + } + + return res; err: printk(KERN_INFO "%s: Error initializing chip.\n", PCF8563_NAME); - return -1; + res = -1; + return res; } void __exit @@ -187,8 +212,8 @@ pcf8563_exit(void) * ioctl calls for this driver. Why return -ENOTTY upon error? Because * POSIX says so! */ -int -pcf8563_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned long arg) +int pcf8563_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, + unsigned long arg) { /* Some sanity checks. */ if (_IOC_TYPE(cmd) != RTC_MAGIC) @@ -198,124 +223,146 @@ pcf8563_ioctl(struct inode *inode, struct file *filp, unsigned int cmd, unsigned return -ENOTTY; switch (cmd) { - case RTC_RD_TIME: - { - struct rtc_time tm; - - spin_lock(&rtc_lock); - get_rtc_time(&tm); - - if (copy_to_user((struct rtc_time *) arg, &tm, sizeof(struct rtc_time))) { - spin_unlock(&rtc_lock); - return -EFAULT; - } - - spin_unlock(&rtc_lock); - return 0; - } - break; - case RTC_SET_TIME: - { -#ifdef CONFIG_ETRAX_RTC_READONLY - return -EPERM; -#else - int leap; - int century; - struct rtc_time tm; - - memset(&tm, 0, sizeof (struct rtc_time)); - if (!capable(CAP_SYS_TIME)) - return -EPERM; - - if (copy_from_user(&tm, (struct rtc_time *) arg, sizeof(struct rtc_time))) - return -EFAULT; - - /* Convert from struct tm to struct rtc_time. */ - tm.tm_year += 1900; - tm.tm_mon += 1; - - leap = ((tm.tm_mon == 2) && ((tm.tm_year % 4) == 0)) ? 1 : 0; - - /* Perform some sanity checks. */ - if ((tm.tm_year < 1970) || - (tm.tm_mon > 12) || - (tm.tm_mday == 0) || - (tm.tm_mday > days_in_month[tm.tm_mon] + leap) || - (tm.tm_hour >= 24) || - (tm.tm_min >= 60) || - (tm.tm_sec >= 60)) - return -EINVAL; - - century = (tm.tm_year >= 2000) ? 0x80 : 0; - tm.tm_year = tm.tm_year % 100; - - BIN_TO_BCD(tm.tm_year); - BIN_TO_BCD(tm.tm_mday); - BIN_TO_BCD(tm.tm_hour); - BIN_TO_BCD(tm.tm_min); - BIN_TO_BCD(tm.tm_sec); - tm.tm_mon |= century; - - spin_lock(&rtc_lock); - - rtc_write(RTC_YEAR, tm.tm_year); - rtc_write(RTC_MONTH, tm.tm_mon); - rtc_write(RTC_DAY_OF_MONTH, tm.tm_mday); - rtc_write(RTC_HOURS, tm.tm_hour); - rtc_write(RTC_MINUTES, tm.tm_min); - rtc_write(RTC_SECONDS, tm.tm_sec); - - spin_unlock(&rtc_lock); - - return 0; -#endif /* !CONFIG_ETRAX_RTC_READONLY */ - } - - case RTC_VLOW_RD: - { - int vl_bit = 0; - - if (rtc_read(RTC_SECONDS) & 0x80) { - vl_bit = 1; - printk(KERN_WARNING "%s: RTC Voltage Low - reliable " - "date/time information is no longer guaranteed!\n", - PCF8563_NAME); - } - if (copy_to_user((int *) arg, &vl_bit, sizeof(int))) - return -EFAULT; - - return 0; - } + case RTC_RD_TIME: + { + struct rtc_time tm; - case RTC_VLOW_SET: - { - /* Clear the VL bit in the seconds register */ - int ret = rtc_read(RTC_SECONDS); + mutex_lock(&rtc_lock); + memset(&tm, 0, sizeof tm); + get_rtc_time(&tm); - rtc_write(RTC_SECONDS, (ret & 0x7F)); + if (copy_to_user((struct rtc_time *) arg, &tm, + sizeof tm)) { + spin_unlock(&rtc_lock); + return -EFAULT; + } + + mutex_unlock(&rtc_lock); - return 0; + return 0; + } + case RTC_SET_TIME: + { + int leap; + int year; + int century; + struct rtc_time tm; + + memset(&tm, 0, sizeof tm); + if (!capable(CAP_SYS_TIME)) + return -EPERM; + + if (copy_from_user(&tm, (struct rtc_time *) arg, sizeof tm)) + return -EFAULT; + + /* Convert from struct tm to struct rtc_time. */ + tm.tm_year += 1900; + tm.tm_mon += 1; + + /* + * Check if tm.tm_year is a leap year. A year is a leap + * year if it is divisible by 4 but not 100, except + * that years divisible by 400 _are_ leap years. + */ + year = tm.tm_year; + leap = (tm.tm_mon == 2) && + ((year % 4 == 0 && year % 100 != 0) || year % 400 == 0); + + /* Perform some sanity checks. */ + if ((tm.tm_year < 1970) || + (tm.tm_mon > 12) || + (tm.tm_mday == 0) || + (tm.tm_mday > days_in_month[tm.tm_mon] + leap) || + (tm.tm_wday >= 7) || + (tm.tm_hour >= 24) || + (tm.tm_min >= 60) || + (tm.tm_sec >= 60)) + return -EINVAL; + + century = (tm.tm_year >= 2000) ? 0x80 : 0; + tm.tm_year = tm.tm_year % 100; + + BIN_TO_BCD(tm.tm_year); + BIN_TO_BCD(tm.tm_mon); + BIN_TO_BCD(tm.tm_mday); + BIN_TO_BCD(tm.tm_hour); + BIN_TO_BCD(tm.tm_min); + BIN_TO_BCD(tm.tm_sec); + tm.tm_mon |= century; + + mutex_lock(&rtc_lock); + + rtc_write(RTC_YEAR, tm.tm_year); + rtc_write(RTC_MONTH, tm.tm_mon); + rtc_write(RTC_WEEKDAY, tm.tm_wday); /* Not coded in BCD. */ + rtc_write(RTC_DAY_OF_MONTH, tm.tm_mday); + rtc_write(RTC_HOURS, tm.tm_hour); + rtc_write(RTC_MINUTES, tm.tm_min); + rtc_write(RTC_SECONDS, tm.tm_sec); + + mutex_unlock(&rtc_lock); + + return 0; + } + case RTC_VL_READ: + if (voltage_low) { + printk(KERN_ERR "%s: RTC Voltage Low - " + "reliable date/time information is no " + "longer guaranteed!\n", PCF8563_NAME); } - default: - return -ENOTTY; + if (copy_to_user((int *) arg, &voltage_low, sizeof(int))) + return -EFAULT; + return 0; + + case RTC_VL_CLR: + { + /* Clear the VL bit in the seconds register in case + * the time has not been set already (which would + * have cleared it). This does not really matter + * because of the cached voltage_low value but do it + * anyway for consistency. */ + + int ret = rtc_read(RTC_SECONDS); + + rtc_write(RTC_SECONDS, (ret & 0x7F)); + + /* Clear the cached value. */ + voltage_low = 0; + + return 0; + } + default: + return -ENOTTY; } return 0; } -static int __init -pcf8563_register(void) +static int __init pcf8563_register(void) { - pcf8563_init(); + if (pcf8563_init() < 0) { + printk(KERN_INFO "%s: Unable to initialize Real-Time Clock " + "Driver, %s\n", PCF8563_NAME, DRIVER_VERSION); + return -1; + } + if (register_chrdev(PCF8563_MAJOR, DEVICE_NAME, &pcf8563_fops) < 0) { printk(KERN_INFO "%s: Unable to get major number %d for RTC device.\n", PCF8563_NAME, PCF8563_MAJOR); return -1; } - printk(KERN_INFO "%s Real-Time Clock Driver, %s\n", PCF8563_NAME, DRIVER_VERSION); - return 0; + printk(KERN_INFO "%s Real-Time Clock Driver, %s\n", PCF8563_NAME, + DRIVER_VERSION); + + /* Check for low voltage, and warn about it. */ + if (voltage_low) { + printk(KERN_WARNING "%s: RTC Voltage Low - reliable date/time " + "information is no longer guaranteed!\n", PCF8563_NAME); + } + + return 0; } module_init(pcf8563_register); diff --git a/arch/cris/arch-v10/drivers/sync_serial.c b/arch/cris/arch-v10/drivers/sync_serial.c new file mode 100644 index 000000000000..069546e342c5 --- /dev/null +++ b/arch/cris/arch-v10/drivers/sync_serial.c @@ -0,0 +1,1441 @@ +/* + * Simple synchronous serial port driver for ETRAX 100LX. + * + * Synchronous serial ports are used for continuous streamed data like audio. + * The default setting for this driver is compatible with the STA 013 MP3 + * decoder. The driver can easily be tuned to fit other audio encoder/decoders + * and SPI + * + * Copyright (c) 2001-2008 Axis Communications AB + * + * Author: Mikael Starvik, Johan Adolfsson + * + */ +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/errno.h> +#include <linux/major.h> +#include <linux/sched.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/poll.h> +#include <linux/init.h> +#include <linux/timer.h> +#include <asm/irq.h> +#include <asm/dma.h> +#include <asm/io.h> +#include <asm/arch/svinto.h> +#include <asm/uaccess.h> +#include <asm/system.h> +#include <asm/sync_serial.h> +#include <asm/arch/io_interface_mux.h> + +/* The receiver is a bit tricky beacuse of the continuous stream of data.*/ +/* */ +/* Three DMA descriptors are linked together. Each DMA descriptor is */ +/* responsible for port->bufchunk of a common buffer. */ +/* */ +/* +---------------------------------------------+ */ +/* | +----------+ +----------+ +----------+ | */ +/* +-> | Descr[0] |-->| Descr[1] |-->| Descr[2] |-+ */ +/* +----------+ +----------+ +----------+ */ +/* | | | */ +/* v v v */ +/* +-------------------------------------+ */ +/* | BUFFER | */ +/* +-------------------------------------+ */ +/* |<- data_avail ->| */ +/* readp writep */ +/* */ +/* If the application keeps up the pace readp will be right after writep.*/ +/* If the application can't keep the pace we have to throw away data. */ +/* The idea is that readp should be ready with the data pointed out by */ +/* Descr[i] when the DMA has filled in Descr[i+1]. */ +/* Otherwise we will discard */ +/* the rest of the data pointed out by Descr1 and set readp to the start */ +/* of Descr2 */ + +#define SYNC_SERIAL_MAJOR 125 + +/* IN_BUFFER_SIZE should be a multiple of 6 to make sure that 24 bit */ +/* words can be handled */ +#define IN_BUFFER_SIZE 12288 +#define IN_DESCR_SIZE 256 +#define NUM_IN_DESCR (IN_BUFFER_SIZE/IN_DESCR_SIZE) +#define OUT_BUFFER_SIZE 4096 + +#define DEFAULT_FRAME_RATE 0 +#define DEFAULT_WORD_RATE 7 + +/* NOTE: Enabling some debug will likely cause overrun or underrun, + * especially if manual mode is use. + */ +#define DEBUG(x) +#define DEBUGREAD(x) +#define DEBUGWRITE(x) +#define DEBUGPOLL(x) +#define DEBUGRXINT(x) +#define DEBUGTXINT(x) + +/* Define some macros to access ETRAX 100 registers */ +#define SETF(var, reg, field, val) \ + do { \ + var = (var & ~IO_MASK_(reg##_, field##_)) | \ + IO_FIELD_(reg##_, field##_, val); \ + } while (0) + +#define SETS(var, reg, field, val) \ + do { \ + var = (var & ~IO_MASK_(reg##_, field##_)) | \ + IO_STATE_(reg##_, field##_, _##val); \ + } while (0) + +struct sync_port { + /* Etrax registers and bits*/ + const volatile unsigned *const status; + volatile unsigned *const ctrl_data; + volatile unsigned *const output_dma_first; + volatile unsigned char *const output_dma_cmd; + volatile unsigned char *const output_dma_clr_irq; + volatile unsigned *const input_dma_first; + volatile unsigned char *const input_dma_cmd; + volatile unsigned *const input_dma_descr; + /* 8*4 */ + volatile unsigned char *const input_dma_clr_irq; + volatile unsigned *const data_out; + const volatile unsigned *const data_in; + char data_avail_bit; /* In R_IRQ_MASK1_RD/SET/CLR */ + char transmitter_ready_bit; /* In R_IRQ_MASK1_RD/SET/CLR */ + char input_dma_descr_bit; /* In R_IRQ_MASK2_RD */ + + char output_dma_bit; /* In R_IRQ_MASK2_RD */ + /* End of fields initialised in array */ + char started; /* 1 if port has been started */ + char port_nbr; /* Port 0 or 1 */ + char busy; /* 1 if port is busy */ + + char enabled; /* 1 if port is enabled */ + char use_dma; /* 1 if port uses dma */ + char tr_running; + + char init_irqs; + + /* Register shadow */ + unsigned int ctrl_data_shadow; + /* Remaining bytes for current transfer */ + volatile unsigned int out_count; + /* Current position in out_buffer */ + unsigned char *outp; + /* 16*4 */ + /* Next byte to be read by application */ + volatile unsigned char *volatile readp; + /* Next byte to be written by etrax */ + volatile unsigned char *volatile writep; + + unsigned int in_buffer_size; + unsigned int inbufchunk; + struct etrax_dma_descr out_descr __attribute__ ((aligned(32))); + struct etrax_dma_descr in_descr[NUM_IN_DESCR] __attribute__ ((aligned(32))); + unsigned char out_buffer[OUT_BUFFER_SIZE] __attribute__ ((aligned(32))); + unsigned char in_buffer[IN_BUFFER_SIZE]__attribute__ ((aligned(32))); + unsigned char flip[IN_BUFFER_SIZE] __attribute__ ((aligned(32))); + struct etrax_dma_descr *next_rx_desc; + struct etrax_dma_descr *prev_rx_desc; + int full; + + wait_queue_head_t out_wait_q; + wait_queue_head_t in_wait_q; +}; + + +static int etrax_sync_serial_init(void); +static void initialize_port(int portnbr); +static inline int sync_data_avail(struct sync_port *port); + +static int sync_serial_open(struct inode *inode, struct file *file); +static int sync_serial_release(struct inode *inode, struct file *file); +static unsigned int sync_serial_poll(struct file *filp, poll_table *wait); + +static int sync_serial_ioctl(struct inode *inode, struct file *file, + unsigned int cmd, unsigned long arg); +static ssize_t sync_serial_write(struct file *file, const char *buf, + size_t count, loff_t *ppos); +static ssize_t sync_serial_read(struct file *file, char *buf, + size_t count, loff_t *ppos); + +#if ((defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) && \ + defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA)) || \ + (defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1) && \ + defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA))) +#define SYNC_SER_DMA +#endif + +static void send_word(struct sync_port *port); +static void start_dma(struct sync_port *port, const char *data, int count); +static void start_dma_in(struct sync_port *port); +#ifdef SYNC_SER_DMA +static irqreturn_t tr_interrupt(int irq, void *dev_id); +static irqreturn_t rx_interrupt(int irq, void *dev_id); +#endif +#if ((defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) && \ + !defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA)) || \ + (defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1) && \ + !defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA))) +#define SYNC_SER_MANUAL +#endif +#ifdef SYNC_SER_MANUAL +static irqreturn_t manual_interrupt(int irq, void *dev_id); +#endif + +/* The ports */ +static struct sync_port ports[] = { + { + .status = R_SYNC_SERIAL1_STATUS, + .ctrl_data = R_SYNC_SERIAL1_CTRL, + .output_dma_first = R_DMA_CH8_FIRST, + .output_dma_cmd = R_DMA_CH8_CMD, + .output_dma_clr_irq = R_DMA_CH8_CLR_INTR, + .input_dma_first = R_DMA_CH9_FIRST, + .input_dma_cmd = R_DMA_CH9_CMD, + .input_dma_descr = R_DMA_CH9_DESCR, + .input_dma_clr_irq = R_DMA_CH9_CLR_INTR, + .data_out = R_SYNC_SERIAL1_TR_DATA, + .data_in = R_SYNC_SERIAL1_REC_DATA, + .data_avail_bit = IO_BITNR(R_IRQ_MASK1_RD, ser1_data), + .transmitter_ready_bit = IO_BITNR(R_IRQ_MASK1_RD, ser1_ready), + .input_dma_descr_bit = IO_BITNR(R_IRQ_MASK2_RD, dma9_descr), + .output_dma_bit = IO_BITNR(R_IRQ_MASK2_RD, dma8_eop), + .init_irqs = 1, +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA) + .use_dma = 1, +#else + .use_dma = 0, +#endif + }, + { + .status = R_SYNC_SERIAL3_STATUS, + .ctrl_data = R_SYNC_SERIAL3_CTRL, + .output_dma_first = R_DMA_CH4_FIRST, + .output_dma_cmd = R_DMA_CH4_CMD, + .output_dma_clr_irq = R_DMA_CH4_CLR_INTR, + .input_dma_first = R_DMA_CH5_FIRST, + .input_dma_cmd = R_DMA_CH5_CMD, + .input_dma_descr = R_DMA_CH5_DESCR, + .input_dma_clr_irq = R_DMA_CH5_CLR_INTR, + .data_out = R_SYNC_SERIAL3_TR_DATA, + .data_in = R_SYNC_SERIAL3_REC_DATA, + .data_avail_bit = IO_BITNR(R_IRQ_MASK1_RD, ser3_data), + .transmitter_ready_bit = IO_BITNR(R_IRQ_MASK1_RD, ser3_ready), + .input_dma_descr_bit = IO_BITNR(R_IRQ_MASK2_RD, dma5_descr), + .output_dma_bit = IO_BITNR(R_IRQ_MASK2_RD, dma4_eop), + .init_irqs = 1, +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA) + .use_dma = 1, +#else + .use_dma = 0, +#endif + } +}; + +/* Register shadows */ +static unsigned sync_serial_prescale_shadow; + +#define NUMBER_OF_PORTS 2 + +static struct file_operations sync_serial_fops = { + .owner = THIS_MODULE, + .write = sync_serial_write, + .read = sync_serial_read, + .poll = sync_serial_poll, + .ioctl = sync_serial_ioctl, + .open = sync_serial_open, + .release = sync_serial_release +}; + +static int __init etrax_sync_serial_init(void) +{ + ports[0].enabled = 0; + ports[1].enabled = 0; + +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) + if (cris_request_io_interface(if_sync_serial_1, "sync_ser1")) { + printk(KERN_CRIT "ETRAX100LX sync_serial: " + "Could not allocate IO group for port %d\n", 0); + return -EBUSY; + } +#endif +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1) + if (cris_request_io_interface(if_sync_serial_3, "sync_ser3")) { +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) + cris_free_io_interface(if_sync_serial_1); +#endif + printk(KERN_CRIT "ETRAX100LX sync_serial: " + "Could not allocate IO group for port %d\n", 1); + return -EBUSY; + } +#endif + + if (register_chrdev(SYNC_SERIAL_MAJOR, "sync serial", + &sync_serial_fops) < 0) { +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1) + cris_free_io_interface(if_sync_serial_3); +#endif +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) + cris_free_io_interface(if_sync_serial_1); +#endif + printk("unable to get major for synchronous serial port\n"); + return -EBUSY; + } + + /* Deselect synchronous serial ports while configuring. */ + SETS(gen_config_ii_shadow, R_GEN_CONFIG_II, sermode1, async); + SETS(gen_config_ii_shadow, R_GEN_CONFIG_II, sermode3, async); + *R_GEN_CONFIG_II = gen_config_ii_shadow; + + /* Initialize Ports */ +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT0) + ports[0].enabled = 1; + SETS(port_pb_i2c_shadow, R_PORT_PB_I2C, syncser1, ss1extra); + SETS(gen_config_ii_shadow, R_GEN_CONFIG_II, sermode1, sync); +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL0_DMA) + ports[0].use_dma = 1; +#else + ports[0].use_dma = 0; +#endif + initialize_port(0); +#endif + +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL_PORT1) + ports[1].enabled = 1; + SETS(port_pb_i2c_shadow, R_PORT_PB_I2C, syncser3, ss3extra); + SETS(gen_config_ii_shadow, R_GEN_CONFIG_II, sermode3, sync); +#if defined(CONFIG_ETRAX_SYNCHRONOUS_SERIAL1_DMA) + ports[1].use_dma = 1; +#else + ports[1].use_dma = 0; +#endif + initialize_port(1); +#endif + + *R_PORT_PB_I2C = port_pb_i2c_shadow; /* Use PB4/PB7 */ + + /* Set up timing */ + *R_SYNC_SERIAL_PRESCALE = sync_serial_prescale_shadow = ( + IO_STATE(R_SYNC_SERIAL_PRESCALE, clk_sel_u1, codec) | + IO_STATE(R_SYNC_SERIAL_PRESCALE, word_stb_sel_u1, external) | + IO_STATE(R_SYNC_SERIAL_PRESCALE, clk_sel_u3, codec) | + IO_STATE(R_SYNC_SERIAL_PRESCALE, word_stb_sel_u3, external) | + IO_STATE(R_SYNC_SERIAL_PRESCALE, prescaler, div4) | + IO_FIELD(R_SYNC_SERIAL_PRESCALE, frame_rate, + DEFAULT_FRAME_RATE) | + IO_FIELD(R_SYNC_SERIAL_PRESCALE, word_rate, DEFAULT_WORD_RATE) | + IO_STATE(R_SYNC_SERIAL_PRESCALE, warp_mode, normal)); + + /* Select synchronous ports */ + *R_GEN_CONFIG_II = gen_config_ii_shadow; + + printk(KERN_INFO "ETRAX 100LX synchronous serial port driver\n"); + return 0; +} + +static void __init initialize_port(int portnbr) +{ + struct sync_port *port = &ports[portnbr]; + + DEBUG(printk(KERN_DEBUG "Init sync serial port %d\n", portnbr)); + + port->started = 0; + port->port_nbr = portnbr; + port->busy = 0; + port->tr_running = 0; + + port->out_count = 0; + port->outp = port->out_buffer; + + port->readp = port->flip; + port->writep = port->flip; + port->in_buffer_size = IN_BUFFER_SIZE; + port->inbufchunk = IN_DESCR_SIZE; + port->next_rx_desc = &port->in_descr[0]; + port->prev_rx_desc = &port->in_descr[NUM_IN_DESCR-1]; + port->prev_rx_desc->ctrl = d_eol; + + init_waitqueue_head(&port->out_wait_q); + init_waitqueue_head(&port->in_wait_q); + + port->ctrl_data_shadow = + IO_STATE(R_SYNC_SERIAL1_CTRL, tr_baud, c115k2Hz) | + IO_STATE(R_SYNC_SERIAL1_CTRL, mode, master_output) | + IO_STATE(R_SYNC_SERIAL1_CTRL, error, ignore) | + IO_STATE(R_SYNC_SERIAL1_CTRL, rec_enable, disable) | + IO_STATE(R_SYNC_SERIAL1_CTRL, f_synctype, normal) | + IO_STATE(R_SYNC_SERIAL1_CTRL, f_syncsize, word) | + IO_STATE(R_SYNC_SERIAL1_CTRL, f_sync, on) | + IO_STATE(R_SYNC_SERIAL1_CTRL, clk_mode, normal) | + IO_STATE(R_SYNC_SERIAL1_CTRL, clk_halt, stopped) | + IO_STATE(R_SYNC_SERIAL1_CTRL, bitorder, msb) | + IO_STATE(R_SYNC_SERIAL1_CTRL, tr_enable, disable) | + IO_STATE(R_SYNC_SERIAL1_CTRL, wordsize, size8bit) | + IO_STATE(R_SYNC_SERIAL1_CTRL, buf_empty, lmt_8) | + IO_STATE(R_SYNC_SERIAL1_CTRL, buf_full, lmt_8) | + IO_STATE(R_SYNC_SERIAL1_CTRL, flow_ctrl, enabled) | + IO_STATE(R_SYNC_SERIAL1_CTRL, clk_polarity, neg) | + IO_STATE(R_SYNC_SERIAL1_CTRL, frame_polarity, normal)| + IO_STATE(R_SYNC_SERIAL1_CTRL, status_polarity, inverted)| + IO_STATE(R_SYNC_SERIAL1_CTRL, clk_driver, normal) | + IO_STATE(R_SYNC_SERIAL1_CTRL, frame_driver, normal) | + IO_STATE(R_SYNC_SERIAL1_CTRL, status_driver, normal)| + IO_STATE(R_SYNC_SERIAL1_CTRL, def_out0, high); + + if (port->use_dma) + port->ctrl_data_shadow |= IO_STATE(R_SYNC_SERIAL1_CTRL, + dma_enable, on); + else + port->ctrl_data_shadow |= IO_STATE(R_SYNC_SERIAL1_CTRL, + dma_enable, off); + + *port->ctrl_data = port->ctrl_data_shadow; +} + +static inline int sync_data_avail(struct sync_port *port) +{ + int avail; + unsigned char *start; + unsigned char *end; + + start = (unsigned char *)port->readp; /* cast away volatile */ + end = (unsigned char *)port->writep; /* cast away volatile */ + /* 0123456789 0123456789 + * ----- - ----- + * ^rp ^wp ^wp ^rp + */ + if (end >= start) + avail = end - start; + else + avail = port->in_buffer_size - (start - end); + return avail; +} + +static inline int sync_data_avail_to_end(struct sync_port *port) +{ + int avail; + unsigned char *start; + unsigned char *end; + + start = (unsigned char *)port->readp; /* cast away volatile */ + end = (unsigned char *)port->writep; /* cast away volatile */ + /* 0123456789 0123456789 + * ----- ----- + * ^rp ^wp ^wp ^rp + */ + + if (end >= start) + avail = end - start; + else + avail = port->flip + port->in_buffer_size - start; + return avail; +} + + +static int sync_serial_open(struct inode *inode, struct file *file) +{ + int dev = MINOR(inode->i_rdev); + struct sync_port *port; + int mode; + + DEBUG(printk(KERN_DEBUG "Open sync serial port %d\n", dev)); + + if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) { + DEBUG(printk(KERN_DEBUG "Invalid minor %d\n", dev)); + return -ENODEV; + } + port = &ports[dev]; + /* Allow open this device twice (assuming one reader and one writer) */ + if (port->busy == 2) { + DEBUG(printk(KERN_DEBUG "Device is busy.. \n")); + return -EBUSY; + } + if (port->init_irqs) { + if (port->use_dma) { + if (port == &ports[0]) { +#ifdef SYNC_SER_DMA + if (request_irq(24, tr_interrupt, 0, + "synchronous serial 1 dma tr", + &ports[0])) { + printk(KERN_CRIT "Can't alloc " + "sync serial port 1 IRQ"); + return -EBUSY; + } else if (request_irq(25, rx_interrupt, 0, + "synchronous serial 1 dma rx", + &ports[0])) { + free_irq(24, &port[0]); + printk(KERN_CRIT "Can't alloc " + "sync serial port 1 IRQ"); + return -EBUSY; + } else if (cris_request_dma(8, + "synchronous serial 1 dma tr", + DMA_VERBOSE_ON_ERROR, + dma_ser1)) { + free_irq(24, &port[0]); + free_irq(25, &port[0]); + printk(KERN_CRIT "Can't alloc " + "sync serial port 1 " + "TX DMA channel"); + return -EBUSY; + } else if (cris_request_dma(9, + "synchronous serial 1 dma rec", + DMA_VERBOSE_ON_ERROR, + dma_ser1)) { + cris_free_dma(8, NULL); + free_irq(24, &port[0]); + free_irq(25, &port[0]); + printk(KERN_CRIT "Can't alloc " + "sync serial port 1 " + "RX DMA channel"); + return -EBUSY; + } +#endif + RESET_DMA(8); WAIT_DMA(8); + RESET_DMA(9); WAIT_DMA(9); + *R_DMA_CH8_CLR_INTR = + IO_STATE(R_DMA_CH8_CLR_INTR, clr_eop, + do) | + IO_STATE(R_DMA_CH8_CLR_INTR, clr_descr, + do); + *R_DMA_CH9_CLR_INTR = + IO_STATE(R_DMA_CH9_CLR_INTR, clr_eop, + do) | + IO_STATE(R_DMA_CH9_CLR_INTR, clr_descr, + do); + *R_IRQ_MASK2_SET = + IO_STATE(R_IRQ_MASK2_SET, dma8_eop, + set) | + IO_STATE(R_IRQ_MASK2_SET, dma9_descr, + set); + } else if (port == &ports[1]) { +#ifdef SYNC_SER_DMA + if (request_irq(20, tr_interrupt, 0, + "synchronous serial 3 dma tr", + &ports[1])) { + printk(KERN_CRIT "Can't alloc " + "sync serial port 3 IRQ"); + return -EBUSY; + } else if (request_irq(21, rx_interrupt, 0, + "synchronous serial 3 dma rx", + &ports[1])) { + free_irq(20, &ports[1]); + printk(KERN_CRIT "Can't alloc " + "sync serial port 3 IRQ"); + return -EBUSY; + } else if (cris_request_dma(4, + "synchronous serial 3 dma tr", + DMA_VERBOSE_ON_ERROR, + dma_ser3)) { + free_irq(21, &ports[1]); + free_irq(20, &ports[1]); + printk(KERN_CRIT "Can't alloc " + "sync serial port 3 " + "TX DMA channel"); + return -EBUSY; + } else if (cris_request_dma(5, + "synchronous serial 3 dma rec", + DMA_VERBOSE_ON_ERROR, + dma_ser3)) { + cris_free_dma(4, NULL); + free_irq(21, &ports[1]); + free_irq(20, &ports[1]); + printk(KERN_CRIT "Can't alloc " + "sync serial port 3 " + "RX DMA channel"); + return -EBUSY; + } +#endif + RESET_DMA(4); WAIT_DMA(4); + RESET_DMA(5); WAIT_DMA(5); + *R_DMA_CH4_CLR_INTR = + IO_STATE(R_DMA_CH4_CLR_INTR, clr_eop, + do) | + IO_STATE(R_DMA_CH4_CLR_INTR, clr_descr, + do); + *R_DMA_CH5_CLR_INTR = + IO_STATE(R_DMA_CH5_CLR_INTR, clr_eop, + do) | + IO_STATE(R_DMA_CH5_CLR_INTR, clr_descr, + do); + *R_IRQ_MASK2_SET = + IO_STATE(R_IRQ_MASK2_SET, dma4_eop, + set) | + IO_STATE(R_IRQ_MASK2_SET, dma5_descr, + set); + } + start_dma_in(port); + port->init_irqs = 0; + } else { /* !port->use_dma */ +#ifdef SYNC_SER_MANUAL + if (port == &ports[0]) { + if (request_irq(8, + manual_interrupt, + IRQF_SHARED | IRQF_DISABLED, + "synchronous serial manual irq", + &ports[0])) { + printk(KERN_CRIT "Can't alloc " + "sync serial manual irq"); + return -EBUSY; + } + } else if (port == &ports[1]) { + if (request_irq(8, + manual_interrupt, + IRQF_SHARED | IRQF_DISABLED, + "synchronous serial manual irq", + &ports[1])) { + printk(KERN_CRIT "Can't alloc " + "sync serial manual irq"); + return -EBUSY; + } + } + port->init_irqs = 0; +#else + panic("sync_serial: Manual mode not supported.\n"); +#endif /* SYNC_SER_MANUAL */ + } + } /* port->init_irqs */ + + port->busy++; + /* Start port if we use it as input */ + mode = IO_EXTRACT(R_SYNC_SERIAL1_CTRL, mode, port->ctrl_data_shadow); + if (mode == IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, mode, master_input) || + mode == IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, mode, slave_input) || + mode == IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, mode, master_bidir) || + mode == IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, mode, slave_bidir)) { + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, clk_halt, + running); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, tr_enable, + enable); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, rec_enable, + enable); + port->started = 1; + *port->ctrl_data = port->ctrl_data_shadow; + if (!port->use_dma) + *R_IRQ_MASK1_SET = 1 << port->data_avail_bit; + DEBUG(printk(KERN_DEBUG "sser%d rec started\n", dev)); + } + return 0; +} + +static int sync_serial_release(struct inode *inode, struct file *file) +{ + int dev = MINOR(inode->i_rdev); + struct sync_port *port; + + if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) { + DEBUG(printk(KERN_DEBUG "Invalid minor %d\n", dev)); + return -ENODEV; + } + port = &ports[dev]; + if (port->busy) + port->busy--; + if (!port->busy) + *R_IRQ_MASK1_CLR = ((1 << port->data_avail_bit) | + (1 << port->transmitter_ready_bit)); + + return 0; +} + + + +static unsigned int sync_serial_poll(struct file *file, poll_table *wait) +{ + int dev = MINOR(file->f_dentry->d_inode->i_rdev); + unsigned int mask = 0; + struct sync_port *port; + DEBUGPOLL(static unsigned int prev_mask = 0); + + port = &ports[dev]; + poll_wait(file, &port->out_wait_q, wait); + poll_wait(file, &port->in_wait_q, wait); + /* Some room to write */ + if (port->out_count < OUT_BUFFER_SIZE) + mask |= POLLOUT | POLLWRNORM; + /* At least an inbufchunk of data */ + if (sync_data_avail(port) >= port->inbufchunk) + mask |= POLLIN | POLLRDNORM; + + DEBUGPOLL(if (mask != prev_mask) + printk(KERN_DEBUG "sync_serial_poll: mask 0x%08X %s %s\n", + mask, + mask & POLLOUT ? "POLLOUT" : "", + mask & POLLIN ? "POLLIN" : ""); + prev_mask = mask; + ); + return mask; +} + +static int sync_serial_ioctl(struct inode *inode, struct file *file, + unsigned int cmd, unsigned long arg) +{ + int return_val = 0; + unsigned long flags; + + int dev = MINOR(file->f_dentry->d_inode->i_rdev); + struct sync_port *port; + + if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) { + DEBUG(printk(KERN_DEBUG "Invalid minor %d\n", dev)); + return -1; + } + port = &ports[dev]; + + local_irq_save(flags); + /* Disable port while changing config */ + if (dev) { + if (port->use_dma) { + RESET_DMA(4); WAIT_DMA(4); + port->tr_running = 0; + port->out_count = 0; + port->outp = port->out_buffer; + *R_DMA_CH4_CLR_INTR = + IO_STATE(R_DMA_CH4_CLR_INTR, clr_eop, do) | + IO_STATE(R_DMA_CH4_CLR_INTR, clr_descr, do); + } + SETS(gen_config_ii_shadow, R_GEN_CONFIG_II, sermode3, async); + } else { + if (port->use_dma) { + RESET_DMA(8); WAIT_DMA(8); + port->tr_running = 0; + port->out_count = 0; + port->outp = port->out_buffer; + *R_DMA_CH8_CLR_INTR = + IO_STATE(R_DMA_CH8_CLR_INTR, clr_eop, do) | + IO_STATE(R_DMA_CH8_CLR_INTR, clr_descr, do); + } + SETS(gen_config_ii_shadow, R_GEN_CONFIG_II, sermode1, async); + } + *R_GEN_CONFIG_II = gen_config_ii_shadow; + local_irq_restore(flags); + + switch (cmd) { + case SSP_SPEED: + if (GET_SPEED(arg) == CODEC) { + if (dev) + SETS(sync_serial_prescale_shadow, + R_SYNC_SERIAL_PRESCALE, clk_sel_u3, + codec); + else + SETS(sync_serial_prescale_shadow, + R_SYNC_SERIAL_PRESCALE, clk_sel_u1, + codec); + + SETF(sync_serial_prescale_shadow, + R_SYNC_SERIAL_PRESCALE, prescaler, + GET_FREQ(arg)); + SETF(sync_serial_prescale_shadow, + R_SYNC_SERIAL_PRESCALE, frame_rate, + GET_FRAME_RATE(arg)); + SETF(sync_serial_prescale_shadow, + R_SYNC_SERIAL_PRESCALE, word_rate, + GET_WORD_RATE(arg)); + } else { + SETF(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + tr_baud, GET_SPEED(arg)); + if (dev) + SETS(sync_serial_prescale_shadow, + R_SYNC_SERIAL_PRESCALE, clk_sel_u3, + baudrate); + else + SETS(sync_serial_prescale_shadow, + R_SYNC_SERIAL_PRESCALE, clk_sel_u1, + baudrate); + } + break; + case SSP_MODE: + if (arg > 5) + return -EINVAL; + if (arg == MASTER_OUTPUT || arg == SLAVE_OUTPUT) + *R_IRQ_MASK1_CLR = 1 << port->data_avail_bit; + else if (!port->use_dma) + *R_IRQ_MASK1_SET = 1 << port->data_avail_bit; + SETF(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, mode, arg); + break; + case SSP_FRAME_SYNC: + if (arg & NORMAL_SYNC) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + f_synctype, normal); + else if (arg & EARLY_SYNC) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + f_synctype, early); + + if (arg & BIT_SYNC) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + f_syncsize, bit); + else if (arg & WORD_SYNC) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + f_syncsize, word); + else if (arg & EXTENDED_SYNC) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + f_syncsize, extended); + + if (arg & SYNC_ON) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + f_sync, on); + else if (arg & SYNC_OFF) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + f_sync, off); + + if (arg & WORD_SIZE_8) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + wordsize, size8bit); + else if (arg & WORD_SIZE_12) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + wordsize, size12bit); + else if (arg & WORD_SIZE_16) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + wordsize, size16bit); + else if (arg & WORD_SIZE_24) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + wordsize, size24bit); + else if (arg & WORD_SIZE_32) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + wordsize, size32bit); + + if (arg & BIT_ORDER_MSB) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + bitorder, msb); + else if (arg & BIT_ORDER_LSB) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + bitorder, lsb); + + if (arg & FLOW_CONTROL_ENABLE) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + flow_ctrl, enabled); + else if (arg & FLOW_CONTROL_DISABLE) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + flow_ctrl, disabled); + + if (arg & CLOCK_NOT_GATED) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + clk_mode, normal); + else if (arg & CLOCK_GATED) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + clk_mode, gated); + + break; + case SSP_IPOLARITY: + /* NOTE!! negedge is considered NORMAL */ + if (arg & CLOCK_NORMAL) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + clk_polarity, neg); + else if (arg & CLOCK_INVERT) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + clk_polarity, pos); + + if (arg & FRAME_NORMAL) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + frame_polarity, normal); + else if (arg & FRAME_INVERT) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + frame_polarity, inverted); + + if (arg & STATUS_NORMAL) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + status_polarity, normal); + else if (arg & STATUS_INVERT) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + status_polarity, inverted); + break; + case SSP_OPOLARITY: + if (arg & CLOCK_NORMAL) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + clk_driver, normal); + else if (arg & CLOCK_INVERT) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + clk_driver, inverted); + + if (arg & FRAME_NORMAL) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + frame_driver, normal); + else if (arg & FRAME_INVERT) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + frame_driver, inverted); + + if (arg & STATUS_NORMAL) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + status_driver, normal); + else if (arg & STATUS_INVERT) + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + status_driver, inverted); + break; + case SSP_SPI: + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, flow_ctrl, + disabled); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, bitorder, + msb); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, wordsize, + size8bit); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, f_sync, on); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, f_syncsize, + word); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, f_synctype, + normal); + if (arg & SPI_SLAVE) { + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + frame_polarity, inverted); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + clk_polarity, neg); + SETF(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + mode, SLAVE_INPUT); + } else { + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + frame_driver, inverted); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + clk_driver, inverted); + SETF(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, + mode, MASTER_OUTPUT); + } + break; + case SSP_INBUFCHUNK: +#if 0 + if (arg > port->in_buffer_size/NUM_IN_DESCR) + return -EINVAL; + port->inbufchunk = arg; + /* Make sure in_buffer_size is a multiple of inbufchunk */ + port->in_buffer_size = + (port->in_buffer_size/port->inbufchunk) * + port->inbufchunk; + DEBUG(printk(KERN_DEBUG "inbufchunk %i in_buffer_size: %i\n", + port->inbufchunk, port->in_buffer_size)); + if (port->use_dma) { + if (port->port_nbr == 0) { + RESET_DMA(9); + WAIT_DMA(9); + } else { + RESET_DMA(5); + WAIT_DMA(5); + } + start_dma_in(port); + } +#endif + break; + default: + return_val = -1; + } + /* Make sure we write the config without interruption */ + local_irq_save(flags); + /* Set config and enable port */ + *port->ctrl_data = port->ctrl_data_shadow; + nop(); nop(); nop(); nop(); + *R_SYNC_SERIAL_PRESCALE = sync_serial_prescale_shadow; + nop(); nop(); nop(); nop(); + if (dev) + SETS(gen_config_ii_shadow, R_GEN_CONFIG_II, sermode3, sync); + else + SETS(gen_config_ii_shadow, R_GEN_CONFIG_II, sermode1, sync); + + *R_GEN_CONFIG_II = gen_config_ii_shadow; + /* Reset DMA. At readout from serial port the data could be shifted + * one byte if not resetting DMA. + */ + if (port->use_dma) { + if (port->port_nbr == 0) { + RESET_DMA(9); + WAIT_DMA(9); + } else { + RESET_DMA(5); + WAIT_DMA(5); + } + start_dma_in(port); + } + local_irq_restore(flags); + return return_val; +} + + +static ssize_t sync_serial_write(struct file *file, const char *buf, + size_t count, loff_t *ppos) +{ + int dev = MINOR(file->f_dentry->d_inode->i_rdev); + DECLARE_WAITQUEUE(wait, current); + struct sync_port *port; + unsigned long flags; + unsigned long c, c1; + unsigned long free_outp; + unsigned long outp; + unsigned long out_buffer; + + if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) { + DEBUG(printk(KERN_DEBUG "Invalid minor %d\n", dev)); + return -ENODEV; + } + port = &ports[dev]; + + DEBUGWRITE(printk(KERN_DEBUG "W d%d c %lu (%d/%d)\n", + port->port_nbr, count, port->out_count, OUT_BUFFER_SIZE)); + /* Space to end of buffer */ + /* + * out_buffer <c1>012345<- c ->OUT_BUFFER_SIZE + * outp^ +out_count + * ^free_outp + * out_buffer 45<- c ->0123OUT_BUFFER_SIZE + * +out_count outp^ + * free_outp + * + */ + + /* Read variables that may be updated by interrupts */ + local_irq_save(flags); + if (count > OUT_BUFFER_SIZE - port->out_count) + count = OUT_BUFFER_SIZE - port->out_count; + + outp = (unsigned long)port->outp; + free_outp = outp + port->out_count; + local_irq_restore(flags); + out_buffer = (unsigned long)port->out_buffer; + + /* Find out where and how much to write */ + if (free_outp >= out_buffer + OUT_BUFFER_SIZE) + free_outp -= OUT_BUFFER_SIZE; + if (free_outp >= outp) + c = out_buffer + OUT_BUFFER_SIZE - free_outp; + else + c = outp - free_outp; + if (c > count) + c = count; + + DEBUGWRITE(printk(KERN_DEBUG "w op %08lX fop %08lX c %lu\n", + outp, free_outp, c)); + if (copy_from_user((void *)free_outp, buf, c)) + return -EFAULT; + + if (c != count) { + buf += c; + c1 = count - c; + DEBUGWRITE(printk(KERN_DEBUG "w2 fi %lu c %lu c1 %lu\n", + free_outp-out_buffer, c, c1)); + if (copy_from_user((void *)out_buffer, buf, c1)) + return -EFAULT; + } + local_irq_save(flags); + port->out_count += count; + local_irq_restore(flags); + + /* Make sure transmitter/receiver is running */ + if (!port->started) { + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, clk_halt, + running); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, tr_enable, + enable); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, rec_enable, + enable); + port->started = 1; + } + + *port->ctrl_data = port->ctrl_data_shadow; + + if (file->f_flags & O_NONBLOCK) { + local_irq_save(flags); + if (!port->tr_running) { + if (!port->use_dma) { + /* Start sender by writing data */ + send_word(port); + /* and enable transmitter ready IRQ */ + *R_IRQ_MASK1_SET = 1 << + port->transmitter_ready_bit; + } else + start_dma(port, + (unsigned char *volatile)port->outp, c); + } + local_irq_restore(flags); + DEBUGWRITE(printk(KERN_DEBUG "w d%d c %lu NB\n", + port->port_nbr, count)); + return count; + } + + /* Sleep until all sent */ + add_wait_queue(&port->out_wait_q, &wait); + set_current_state(TASK_INTERRUPTIBLE); + local_irq_save(flags); + if (!port->tr_running) { + if (!port->use_dma) { + /* Start sender by writing data */ + send_word(port); + /* and enable transmitter ready IRQ */ + *R_IRQ_MASK1_SET = 1 << port->transmitter_ready_bit; + } else + start_dma(port, port->outp, c); + } + local_irq_restore(flags); + schedule(); + set_current_state(TASK_RUNNING); + remove_wait_queue(&port->out_wait_q, &wait); + if (signal_pending(current)) + return -EINTR; + + DEBUGWRITE(printk(KERN_DEBUG "w d%d c %lu\n", port->port_nbr, count)); + return count; +} + +static ssize_t sync_serial_read(struct file *file, char *buf, + size_t count, loff_t *ppos) +{ + int dev = MINOR(file->f_dentry->d_inode->i_rdev); + int avail; + struct sync_port *port; + unsigned char *start; + unsigned char *end; + unsigned long flags; + + if (dev < 0 || dev >= NUMBER_OF_PORTS || !ports[dev].enabled) { + DEBUG(printk(KERN_DEBUG "Invalid minor %d\n", dev)); + return -ENODEV; + } + port = &ports[dev]; + + DEBUGREAD(printk(KERN_DEBUG "R%d c %d ri %lu wi %lu /%lu\n", + dev, count, port->readp - port->flip, + port->writep - port->flip, port->in_buffer_size)); + + if (!port->started) { + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, clk_halt, + running); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, tr_enable, + enable); + SETS(port->ctrl_data_shadow, R_SYNC_SERIAL1_CTRL, rec_enable, + enable); + port->started = 1; + } + *port->ctrl_data = port->ctrl_data_shadow; + + /* Calculate number of available bytes */ + /* Save pointers to avoid that they are modified by interrupt */ + local_irq_save(flags); + start = (unsigned char *)port->readp; /* cast away volatile */ + end = (unsigned char *)port->writep; /* cast away volatile */ + local_irq_restore(flags); + while (start == end && !port->full) { + /* No data */ + if (file->f_flags & O_NONBLOCK) + return -EAGAIN; + + interruptible_sleep_on(&port->in_wait_q); + if (signal_pending(current)) + return -EINTR; + + local_irq_save(flags); + start = (unsigned char *)port->readp; /* cast away volatile */ + end = (unsigned char *)port->writep; /* cast away volatile */ + local_irq_restore(flags); + } + + /* Lazy read, never return wrapped data. */ + if (port->full) + avail = port->in_buffer_size; + else if (end > start) + avail = end - start; + else + avail = port->flip + port->in_buffer_size - start; + + count = count > avail ? avail : count; + if (copy_to_user(buf, start, count)) + return -EFAULT; + /* Disable interrupts while updating readp */ + local_irq_save(flags); + port->readp += count; + if (port->readp >= port->flip + port->in_buffer_size) /* Wrap? */ + port->readp = port->flip; + port->full = 0; + local_irq_restore(flags); + DEBUGREAD(printk(KERN_DEBUG "r %d\n", count)); + return count; +} + +static void send_word(struct sync_port *port) +{ + switch (IO_EXTRACT(R_SYNC_SERIAL1_CTRL, wordsize, + port->ctrl_data_shadow)) { + case IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, wordsize, size8bit): + port->out_count--; + *port->data_out = *port->outp++; + if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) + port->outp = port->out_buffer; + break; + case IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, wordsize, size12bit): + { + int data = (*port->outp++) << 8; + data |= *port->outp++; + port->out_count -= 2; + *port->data_out = data; + if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) + port->outp = port->out_buffer; + break; + } + case IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, wordsize, size16bit): + port->out_count -= 2; + *port->data_out = *(unsigned short *)port->outp; + port->outp += 2; + if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) + port->outp = port->out_buffer; + break; + case IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, wordsize, size24bit): + port->out_count -= 3; + *port->data_out = *(unsigned int *)port->outp; + port->outp += 3; + if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) + port->outp = port->out_buffer; + break; + case IO_STATE_VALUE(R_SYNC_SERIAL1_CTRL, wordsize, size32bit): + port->out_count -= 4; + *port->data_out = *(unsigned int *)port->outp; + port->outp += 4; + if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) + port->outp = port->out_buffer; + break; + } +} + + +static void start_dma(struct sync_port *port, const char *data, int count) +{ + port->tr_running = 1; + port->out_descr.hw_len = 0; + port->out_descr.next = 0; + port->out_descr.ctrl = d_eol | d_eop; /* No d_wait to avoid glitches */ + port->out_descr.sw_len = count; + port->out_descr.buf = virt_to_phys(data); + port->out_descr.status = 0; + + *port->output_dma_first = virt_to_phys(&port->out_descr); + *port->output_dma_cmd = IO_STATE(R_DMA_CH0_CMD, cmd, start); + DEBUGTXINT(printk(KERN_DEBUG "dma %08lX c %d\n", + (unsigned long)data, count)); +} + +static void start_dma_in(struct sync_port *port) +{ + int i; + unsigned long buf; + port->writep = port->flip; + + if (port->writep > port->flip + port->in_buffer_size) { + panic("Offset too large in sync serial driver\n"); + return; + } + buf = virt_to_phys(port->in_buffer); + for (i = 0; i < NUM_IN_DESCR; i++) { + port->in_descr[i].sw_len = port->inbufchunk; + port->in_descr[i].ctrl = d_int; + port->in_descr[i].next = virt_to_phys(&port->in_descr[i+1]); + port->in_descr[i].buf = buf; + port->in_descr[i].hw_len = 0; + port->in_descr[i].status = 0; + port->in_descr[i].fifo_len = 0; + buf += port->inbufchunk; + prepare_rx_descriptor(&port->in_descr[i]); + } + /* Link the last descriptor to the first */ + port->in_descr[i-1].next = virt_to_phys(&port->in_descr[0]); + port->in_descr[i-1].ctrl |= d_eol; + port->next_rx_desc = &port->in_descr[0]; + port->prev_rx_desc = &port->in_descr[NUM_IN_DESCR - 1]; + *port->input_dma_first = virt_to_phys(port->next_rx_desc); + *port->input_dma_cmd = IO_STATE(R_DMA_CH0_CMD, cmd, start); +} + +#ifdef SYNC_SER_DMA +static irqreturn_t tr_interrupt(int irq, void *dev_id) +{ + unsigned long ireg = *R_IRQ_MASK2_RD; + struct etrax_dma_descr *descr; + unsigned int sentl; + int handled = 0; + int i; + + for (i = 0; i < NUMBER_OF_PORTS; i++) { + struct sync_port *port = &ports[i]; + if (!port->enabled || !port->use_dma) + continue; + + /* IRQ active for the port? */ + if (!(ireg & (1 << port->output_dma_bit))) + continue; + + handled = 1; + + /* Clear IRQ */ + *port->output_dma_clr_irq = + IO_STATE(R_DMA_CH0_CLR_INTR, clr_eop, do) | + IO_STATE(R_DMA_CH0_CLR_INTR, clr_descr, do); + + descr = &port->out_descr; + if (!(descr->status & d_stop)) + sentl = descr->sw_len; + else + /* Otherwise find amount of data sent here */ + sentl = descr->hw_len; + + port->out_count -= sentl; + port->outp += sentl; + if (port->outp >= port->out_buffer + OUT_BUFFER_SIZE) + port->outp = port->out_buffer; + if (port->out_count) { + int c = port->out_buffer + OUT_BUFFER_SIZE - port->outp; + if (c > port->out_count) + c = port->out_count; + DEBUGTXINT(printk(KERN_DEBUG + "tx_int DMAWRITE %i %i\n", sentl, c)); + start_dma(port, port->outp, c); + } else { + DEBUGTXINT(printk(KERN_DEBUG + "tx_int DMA stop %i\n", sentl)); + port->tr_running = 0; + } + /* wake up the waiting process */ + wake_up_interruptible(&port->out_wait_q); + } + return IRQ_RETVAL(handled); +} /* tr_interrupt */ + +static irqreturn_t rx_interrupt(int irq, void *dev_id) +{ + unsigned long ireg = *R_IRQ_MASK2_RD; + int i; + int handled = 0; + + for (i = 0; i < NUMBER_OF_PORTS; i++) { + struct sync_port *port = &ports[i]; + + if (!port->enabled || !port->use_dma) + continue; + + if (!(ireg & (1 << port->input_dma_descr_bit))) + continue; + + /* Descriptor interrupt */ + handled = 1; + while (*port->input_dma_descr != + virt_to_phys(port->next_rx_desc)) { + if (port->writep + port->inbufchunk > port->flip + + port->in_buffer_size) { + int first_size = port->flip + + port->in_buffer_size - port->writep; + memcpy(port->writep, + phys_to_virt(port->next_rx_desc->buf), + first_size); + memcpy(port->flip, + phys_to_virt(port->next_rx_desc->buf + + first_size), + port->inbufchunk - first_size); + port->writep = port->flip + + port->inbufchunk - first_size; + } else { + memcpy(port->writep, + phys_to_virt(port->next_rx_desc->buf), + port->inbufchunk); + port->writep += port->inbufchunk; + if (port->writep >= port->flip + + port->in_buffer_size) + port->writep = port->flip; + } + if (port->writep == port->readp) + port->full = 1; + prepare_rx_descriptor(port->next_rx_desc); + port->next_rx_desc->ctrl |= d_eol; + port->prev_rx_desc->ctrl &= ~d_eol; + port->prev_rx_desc = phys_to_virt((unsigned) + port->next_rx_desc); + port->next_rx_desc = phys_to_virt((unsigned) + port->next_rx_desc->next); + /* Wake up the waiting process */ + wake_up_interruptible(&port->in_wait_q); + *port->input_dma_cmd = IO_STATE(R_DMA_CH1_CMD, + cmd, restart); + /* DMA has reached end of descriptor */ + *port->input_dma_clr_irq = IO_STATE(R_DMA_CH0_CLR_INTR, + clr_descr, do); + } + } + return IRQ_RETVAL(handled); +} /* rx_interrupt */ +#endif /* SYNC_SER_DMA */ + +#ifdef SYNC_SER_MANUAL +static irqreturn_t manual_interrupt(int irq, void *dev_id) +{ + int i; + int handled = 0; + + for (i = 0; i < NUMBER_OF_PORTS; i++) { + struct sync_port *port = &ports[i]; + + if (!port->enabled || port->use_dma) + continue; + + /* Data received? */ + if (*R_IRQ_MASK1_RD & (1 << port->data_avail_bit)) { + handled = 1; + /* Read data */ + switch (port->ctrl_data_shadow & + IO_MASK(R_SYNC_SERIAL1_CTRL, wordsize)) { + case IO_STATE(R_SYNC_SERIAL1_CTRL, wordsize, size8bit): + *port->writep++ = + *(volatile char *)port->data_in; + break; + case IO_STATE(R_SYNC_SERIAL1_CTRL, wordsize, size12bit): + { + int data = *(unsigned short *)port->data_in; + *port->writep = (data & 0x0ff0) >> 4; + *(port->writep + 1) = data & 0x0f; + port->writep += 2; + break; + } + case IO_STATE(R_SYNC_SERIAL1_CTRL, wordsize, size16bit): + *(unsigned short *)port->writep = + *(volatile unsigned short *)port->data_in; + port->writep += 2; + break; + case IO_STATE(R_SYNC_SERIAL1_CTRL, wordsize, size24bit): + *(unsigned int *)port->writep = *port->data_in; + port->writep += 3; + break; + case IO_STATE(R_SYNC_SERIAL1_CTRL, wordsize, size32bit): + *(unsigned int *)port->writep = *port->data_in; + port->writep += 4; + break; + } + + /* Wrap? */ + if (port->writep >= port->flip + port->in_buffer_size) + port->writep = port->flip; + if (port->writep == port->readp) { + /* Receive buffer overrun, discard oldest */ + port->readp++; + /* Wrap? */ + if (port->readp >= port->flip + + port->in_buffer_size) + port->readp = port->flip; + } + if (sync_data_avail(port) >= port->inbufchunk) { + /* Wake up application */ + wake_up_interruptible(&port->in_wait_q); + } + } + + /* Transmitter ready? */ + if (*R_IRQ_MASK1_RD & (1 << port->transmitter_ready_bit)) { + if (port->out_count > 0) { + /* More data to send */ + send_word(port); + } else { + /* Transmission finished */ + /* Turn off IRQ */ + *R_IRQ_MASK1_CLR = 1 << + port->transmitter_ready_bit; + /* Wake up application */ + wake_up_interruptible(&port->out_wait_q); + } + } + } + return IRQ_RETVAL(handled); +} +#endif + +module_init(etrax_sync_serial_init); diff --git a/arch/cris/arch-v10/kernel/debugport.c b/arch/cris/arch-v10/kernel/debugport.c index 93679a48c791..04d5eee2c90c 100644 --- a/arch/cris/arch-v10/kernel/debugport.c +++ b/arch/cris/arch-v10/kernel/debugport.c @@ -1,6 +1,6 @@ /* Serialport functions for debugging * - * Copyright (c) 2000 Axis Communications AB + * Copyright (c) 2000-2007 Axis Communications AB * * Authors: Bjorn Wesen * @@ -11,96 +11,6 @@ * enableDebugIRQ() * init_etrax_debug() * - * $Log: debugport.c,v $ - * Revision 1.27 2005/06/10 10:34:14 starvik - * Real console support - * - * Revision 1.26 2005/06/07 07:06:07 starvik - * Added LF->CR translation to make ETRAX customers happy. - * - * Revision 1.25 2005/03/08 08:56:47 mikaelam - * Do only set index as port->index if port is defined, otherwise use the index from the command line - * - * Revision 1.24 2005/01/19 10:26:33 mikaelam - * Return the cris serial driver in console device driver callback function - * - * Revision 1.23 2005/01/14 10:12:17 starvik - * KGDB on separate port. - * Console fixes from 2.4. - * - * Revision 1.22 2005/01/11 16:06:13 starvik - * typo - * - * Revision 1.21 2005/01/11 13:49:14 starvik - * Added raw_printk to be used where we don't trust the console. - * - * Revision 1.20 2004/12/27 11:18:32 starvik - * Merge of Linux 2.6.10 (not functional yet). - * - * Revision 1.19 2004/10/21 07:26:16 starvik - * Made it possible to specify console settings on kernel command line. - * - * Revision 1.18 2004/10/19 13:07:37 starvik - * Merge of Linux 2.6.9 - * - * Revision 1.17 2004/09/29 10:33:46 starvik - * Resolved a dealock when printing debug from kernel. - * - * Revision 1.16 2004/08/24 06:12:19 starvik - * Whitespace cleanup - * - * Revision 1.15 2004/08/16 12:37:19 starvik - * Merge of Linux 2.6.8 - * - * Revision 1.14 2004/05/17 13:11:29 starvik - * Disable DMA until real serial driver is up - * - * Revision 1.13 2004/05/14 07:58:01 starvik - * Merge of changes from 2.4 - * - * Revision 1.12 2003/09/11 07:29:49 starvik - * Merge of Linux 2.6.0-test5 - * - * Revision 1.11 2003/07/07 09:53:36 starvik - * Revert all the 2.5.74 merge changes to make the console work again - * - * Revision 1.9 2003/02/17 17:07:23 starvik - * Solved the problem with corrupted debug output (from Linux 2.4) - * * Wait until DMA, FIFO and pipe is empty before and after transmissions - * * Buffer data until a FIFO flush can be triggered. - * - * Revision 1.8 2003/01/22 06:48:36 starvik - * Fixed warnings issued by GCC 3.2.1 - * - * Revision 1.7 2002/12/12 08:26:32 starvik - * Don't use C-comments inside CVS comments - * - * Revision 1.6 2002/12/11 15:42:02 starvik - * Extracted v10 (ETRAX 100LX) specific stuff from arch/cris/kernel/ - * - * Revision 1.5 2002/11/20 06:58:03 starvik - * Compiles with kgdb - * - * Revision 1.4 2002/11/19 14:35:24 starvik - * Changes from linux 2.4 - * Changed struct initializer syntax to the currently preferred notation - * - * Revision 1.3 2002/11/06 09:47:03 starvik - * Modified for new interrupt macros - * - * Revision 1.2 2002/01/21 15:21:50 bjornw - * Update for kdev_t changes - * - * Revision 1.6 2001/04/17 13:58:39 orjanf - * * Renamed CONFIG_KGDB to CONFIG_ETRAX_KGDB. - * - * Revision 1.5 2001/03/26 14:22:05 bjornw - * Namechange of some config options - * - * Revision 1.4 2000/10/06 12:37:26 bjornw - * Use physical addresses when talking to DMA - * - * */ #include <linux/console.h> @@ -112,6 +22,8 @@ #include <asm/arch/svinto.h> #include <asm/io.h> /* Get SIMCOUT. */ +extern void reset_watchdog(void); + struct dbg_port { unsigned int index; @@ -188,7 +100,9 @@ struct dbg_port ports[]= } }; +#ifdef CONFIG_ETRAX_SERIAL extern struct tty_driver *serial_driver; +#endif struct dbg_port* port = #if defined(CONFIG_ETRAX_DEBUG_PORT0) @@ -368,11 +282,12 @@ console_write_direct(struct console *co, const char *buf, unsigned int len) { int i; unsigned long flags; - local_irq_save(flags); if (!port) return; + local_irq_save(flags); + /* Send data */ for (i = 0; i < len; i++) { /* LF -> CRLF */ @@ -386,26 +301,16 @@ console_write_direct(struct console *co, const char *buf, unsigned int len) ; *port->write = buf[i]; } - local_irq_restore(flags); -} -int raw_printk(const char *fmt, ...) -{ - static char buf[1024]; - int printed_len; - static int first = 1; - if (first) { - /* Force reinitialization of the port to get manual mode. */ - port->started = 0; - start_port(port); - first = 0; - } - va_list args; - va_start(args, fmt); - printed_len = vsnprintf(buf, sizeof(buf), fmt, args); - va_end(args); - console_write_direct(NULL, buf, strlen(buf)); - return printed_len; + /* + * Feed the watchdog, otherwise it will reset the chip during boot. + * The time to send an ordinary boot message line (10-90 chars) + * varies between 1-8ms at 115200. What makes up for the additional + * 90ms that allows the watchdog to bite? + */ + reset_watchdog(); + + local_irq_restore(flags); } static void @@ -500,6 +405,7 @@ console_setup(struct console *co, char *options) return 0; } + /* This is a dummy serial device that throws away anything written to it. * This is used when no debug output is wanted. */ @@ -555,7 +461,13 @@ etrax_console_device(struct console* co, int *index) { if (port) *index = port->index; + else + *index = 0; +#ifdef CONFIG_ETRAX_SERIAL return port ? serial_driver : &dummy_driver; +#else + return &dummy_driver; +#endif } static struct console sercons = { diff --git a/arch/cris/arch-v10/kernel/dma.c b/arch/cris/arch-v10/kernel/dma.c index e9a0311b141d..eb1fa0d2b49f 100644 --- a/arch/cris/arch-v10/kernel/dma.c +++ b/arch/cris/arch-v10/kernel/dma.c @@ -1,6 +1,5 @@ /* Wrapper for DMA channel allocator that updates DMA client muxing. - * Copyright 2004, Axis Communications AB - * $Id: dma.c,v 1.1 2004/12/13 12:21:51 starvik Exp $ + * Copyright 2004-2007, Axis Communications AB */ #include <linux/kernel.h> diff --git a/arch/cris/arch-v10/kernel/entry.S b/arch/cris/arch-v10/kernel/entry.S index d1361dc119e2..3a65f322ae07 100644 --- a/arch/cris/arch-v10/kernel/entry.S +++ b/arch/cris/arch-v10/kernel/entry.S @@ -1,252 +1,9 @@ -/* $Id: entry.S,v 1.28 2005/06/20 05:06:30 starvik Exp $ - * +/* * linux/arch/cris/entry.S * * Copyright (C) 2000, 2001, 2002 Axis Communications AB * * Authors: Bjorn Wesen (bjornw@axis.com) - * - * $Log: entry.S,v $ - * Revision 1.28 2005/06/20 05:06:30 starvik - * Remove unnecessary diff to kernel.org tree - * - * Revision 1.27 2005/03/04 08:16:16 starvik - * Merge of Linux 2.6.11. - * - * Revision 1.26 2005/01/11 13:49:47 starvik - * Added NMI handler. - * - * Revision 1.25 2004/12/27 11:18:32 starvik - * Merge of Linux 2.6.10 (not functional yet). - * - * Revision 1.24 2004/12/22 10:41:23 starvik - * Updates to make v10 compile with the latest SMP aware generic code (even - * though v10 will never have SMP). - * - * Revision 1.23 2004/10/19 13:07:37 starvik - * Merge of Linux 2.6.9 - * - * Revision 1.22 2004/06/21 10:29:55 starvik - * Merge of Linux 2.6.7 - * - * Revision 1.21 2004/06/09 05:30:27 starvik - * Clean up multiple interrupt handling. - * Prevent interrupts from interrupting each other. - * Handle all active interrupts. - * - * Revision 1.20 2004/06/08 08:55:32 starvik - * Removed unused code - * - * Revision 1.19 2004/06/04 11:56:15 starvik - * Implemented page table lookup for refills in assembler for improved performance. - * - * Revision 1.18 2004/05/11 12:28:25 starvik - * Merge of Linux 2.6.6 - * - * Revision 1.17 2003/09/11 07:29:49 starvik - * Merge of Linux 2.6.0-test5 - * - * Revision 1.16 2003/07/04 08:27:41 starvik - * Merge of Linux 2.5.74 - * - * Revision 1.15 2003/04/09 07:32:55 starvik - * resume should return task_struct, not thread_info - * - * Revision 1.14 2003/04/09 05:20:44 starvik - * Merge of Linux 2.5.67 - * - * Revision 1.13 2002/12/11 15:42:02 starvik - * Extracted v10 (ETRAX 100LX) specific stuff from arch/cris/kernel/*.c - * - * Revision 1.12 2002/12/10 09:00:10 starvik - * Merge of Linux 2.5.51 - * - * Revision 1.11 2002/12/05 07:53:10 starvik - * Corrected constants used with btstq - * - * Revision 1.10 2002/11/27 08:45:10 starvik - * pid is in task_struct, not thread_info - * - * Revision 1.9 2002/11/26 09:52:05 starvik - * Added preemptive kernel scheduling (if CONFIG_PREEMPT) - * - * Revision 1.8 2002/11/20 11:56:11 starvik - * Merge of Linux 2.5.48 - * - * Revision 1.7 2002/11/18 13:02:42 starvik - * Added fourth parameter to do_notify_resume - * Minor cleanup - * - * Revision 1.6 2002/11/11 10:37:50 starvik - * Use new asm-offset defines - * Modified for new location of current->work etc - * Removed SYMBOL_NAME from syscalls - * Added some new syscalls - * - * Revision 1.5 2002/11/05 06:45:11 starvik - * Merge of Linux 2.5.45 - * - * Revision 1.4 2002/02/05 15:41:31 bjornw - * Rewritten to conform better to current 2.5 code (similar to arch/i386) - * - * Revision 1.3 2002/01/21 15:22:20 bjornw - * NICE_DOGGY fix from 2.4 arch/cris - * - * Revision 1.37 2001/12/07 17:03:55 bjornw - * Call a c-hook called watchdog_bite_hook instead of show_registers directly - * - * Revision 1.36 2001/11/22 13:36:36 bjornw - * * In ret_from_intr, check regs->dccr for usermode reentrance instead of - * DCCR explicitly (because the latter might not reflect current reality) - * * In mmu_bus_fault, set $r9 _after_ calling the C-code instead of before - * since $r9 is call-clobbered and is potentially needed afterwards - * - * Revision 1.35 2001/10/30 17:10:15 bjornw - * Add some syscalls - * - * Revision 1.34 2001/10/01 14:45:03 bjornw - * Removed underscores and added register prefixes - * - * Revision 1.33 2001/08/21 13:48:01 jonashg - * Added fix by HP to avoid oops when doing a hard_reset_now. - * - * Revision 1.32 2001/08/14 04:32:02 hp - * In _resume, add comment why R9 is saved; don't sound like it's call-saved. - * - * Revision 1.31 2001/07/25 16:07:42 bjornw - * softirq_active/mask -> softirq_pending only - * - * Revision 1.30 2001/07/05 01:03:32 hp - * - include asm/errno.h to get ENOSYS. - * - Use ENOSYS, not local constant LENOSYS; tweak comments. - * - Explain why .include, not #include is used. - * - Make oops-register-dump if watchdog bits and it's not expected. - * - Don't jsr, use jump _hard_reset_now, and skip spurious nop. - * - Use correct section attribute for section .rodata. - * - Adjust sys_ni_syscall fill number. - * - * Revision 1.29 2001/06/25 14:07:00 hp - * Fix review comment. - * * head.S: Use IO_STATE, IO_FIELD and IO_MASK constructs instead of - * magic numbers. Add comment that -traditional must not be used. - * * entry.S (SYMBOL_NAME): Change redefinition to use ## concatenation. - * Correct and update comment. - * * Makefile (.S.o): Don't use -traditional. Add comment why the - * toplevel rule can't be used (now that there's a reason). - * - * Revision 1.28 2001/06/21 02:00:40 hp - * * entry.S: Include asm/unistd.h. - * (_sys_call_table): Use section .rodata, not .data. - * (_kernel_thread): Move from... - * * process.c: ... here. - * * entryoffsets.c (VAL): Break out from... - * (OF): Use VAL. - * (LCLONE_VM): New asmified value from CLONE_VM. - * - * Revision 1.27 2001/05/29 11:25:27 markusl - * In case of "spurious_interrupt", do hard_reset instead of hanging system in a loop... - * - * Revision 1.26 2001/05/15 15:46:03 bjornw - * Include config.h now that we use some CONFIG_ options - * - * Revision 1.25 2001/05/15 05:38:47 hp - * Tweaked code in _ret_from_sys_call - * - * Revision 1.24 2001/05/15 05:27:49 hp - * Save r9 in r1 over function call rather than on stack. - * - * Revision 1.23 2001/05/15 05:10:00 hp - * Generate entry.S structure offsets from C - * - * Revision 1.22 2001/04/17 13:58:39 orjanf - * * Renamed CONFIG_KGDB to CONFIG_ETRAX_KGDB. - * - * Revision 1.21 2001/04/17 11:33:29 orjanf - * Updated according to review: - * * Included asm/sv_addr_ag.h to get macro for internal register. - * * Corrected comment regarding system call argument passing. - * * Removed comment about instruction being in a delay slot. - * * Added comment about SYMBOL_NAME macro. - * - * Revision 1.20 2001/04/12 08:51:07 hp - * - Add entry for sys_fcntl64. In fact copy last piece from i386 including ... - * - .rept to fill table to safe state with sys_ni_syscall. - * - * Revision 1.19 2001/04/04 09:43:32 orjanf - * * Moved do_sigtrap from traps.c to entry.S. - * * LTASK_PID need not be global anymore. - * - * Revision 1.18 2001/03/26 09:25:02 markusl - * Updated after review, should now handle USB interrupts correctly. - * - * Revision 1.17 2001/03/21 16:12:55 bjornw - * * Always make room for the cpu status record in the frame, in order to - * use the same framelength and layout for both mmu busfaults and normal - * irqs. No need to check for the explicit CRIS_FRAME_FIXUP type anymore. - * * Fixed bug with using addq for popping the stack in the epilogue - it - * destroyed the flag register. Use instructions that don't affect the - * flag register instead. - * * Removed write to R_PORT_PA_DATA during spurious_interrupt - * - * Revision 1.16 2001/03/20 19:43:02 bjornw - * * Get rid of esp0 setting - * * Give a 7th argument to a systemcall - the stackframe - * - * Revision 1.15 2001/03/05 13:14:30 bjornw - * Spelling fix - * - * Revision 1.14 2001/02/23 08:36:36 perf - * New ABI; syscallnr=r9, arg5=mof, arg6=srp. - * Corrected tracesys call check. - * - * Revision 1.13 2001/02/15 08:40:55 perf - * H-P by way of perf; - * - (_system_call): Don't read system call function address into r1. - * - (RBFExit): There is no such thing as a null pop. Adjust sp by addq. - * - (_system_call): Don't use r10 and don't save and restore it. - * - (THREAD_ESP0): New constant. - * - (_system_call): Inline set_esp0. - * - * Revision 1.12 2001/01/31 17:56:25 orjanf - * Added definition of LTASK_PID and made it global. - * - * Revision 1.11 2001/01/10 21:13:29 bjornw - * SYMBOL_NAME is defined incorrectly for the compiler options we currently use - * - * Revision 1.10 2000/12/18 23:47:56 bjornw - * * Added syscall trace support (ptrace), completely untested of course - * * Removed redundant check for NULL entries in syscall_table - * - * Revision 1.9 2000/11/21 16:40:51 bjornw - * * New frame type used when an SBFS frame needs to be popped without - * actually restarting the instruction - * * Enable interrupts in signal_return (they did so in x86, I hope it's a good - * idea) - * - * Revision 1.8 2000/11/17 16:53:35 bjornw - * Added detection of frame-type in Rexit, so that mmu_bus_fault can - * use ret_from_intr in the return-path to check for signals (like SEGV) - * and other foul things that might have occurred during the fault. - * - * Revision 1.7 2000/10/06 15:04:28 bjornw - * Include mof in register savings - * - * Revision 1.6 2000/09/12 16:02:44 bjornw - * Linux-2.4.0-test7 derived updates - * - * Revision 1.5 2000/08/17 15:35:15 bjornw - * 2.4.0-test6 changed local_irq_count and friends API - * - * Revision 1.4 2000/08/02 13:59:30 bjornw - * Removed olduname and uname from the syscall list - * - * Revision 1.3 2000/07/31 13:32:58 bjornw - * * Export ret_from_intr - * * _resume updated (prev/last tjohejsan) - * * timer_interrupt obsolete - * * SIGSEGV detection in mmu_bus_fault temporarily disabled - * - * */ /* @@ -1167,9 +924,11 @@ sys_call_table: .long sys_epoll_pwait .long sys_utimensat /* 320 */ .long sys_signalfd - .long sys_ni_syscall + .long sys_timerfd_create .long sys_eventfd .long sys_fallocate + .long sys_timerfd_settime /* 325 */ + .long sys_timerfd_gettime /* * NOTE!! This doesn't have to be exact - we just have diff --git a/arch/cris/arch-v10/kernel/fasttimer.c b/arch/cris/arch-v10/kernel/fasttimer.c index c1a3a2100ee7..31ff35cff02c 100644 --- a/arch/cris/arch-v10/kernel/fasttimer.c +++ b/arch/cris/arch-v10/kernel/fasttimer.c @@ -31,15 +31,12 @@ #define DEBUG_LOG_INCLUDED #define FAST_TIMER_LOG -//#define FAST_TIMER_TEST +/* #define FAST_TIMER_TEST */ #define FAST_TIMER_SANITY_CHECKS #ifdef FAST_TIMER_SANITY_CHECKS -#define SANITYCHECK(x) x static int sanity_failed; -#else -#define SANITYCHECK(x) #endif #define D1(x) @@ -226,23 +223,19 @@ void start_one_shot_timer(struct fast_timer *t, do_gettimeofday_fast(&t->tv_set); tmp = fast_timer_list; - SANITYCHECK({ /* Check so this is not in the list already... */ - while (tmp != NULL) - { - if (tmp == t) - { - printk(KERN_WARNING - "timer name: %s data: 0x%08lX already in list!\n", name, data); - sanity_failed++; - goto done; - } - else - { - tmp = tmp->next; - } - } - tmp = fast_timer_list; - }); +#ifdef FAST_TIMER_SANITY_CHECKS + /* Check so this is not in the list already... */ + while (tmp != NULL) { + if (tmp == t) { + printk(KERN_WARNING "timer name: %s data: " + "0x%08lX already in list!\n", name, data); + sanity_failed++; + goto done; + } else + tmp = tmp->next; + } + tmp = fast_timer_list; +#endif t->delay_us = delay_us; t->function = function; diff --git a/arch/cris/arch-v10/kernel/head.S b/arch/cris/arch-v10/kernel/head.S index d946d8b8d277..96344afc4ebc 100644 --- a/arch/cris/arch-v10/kernel/head.S +++ b/arch/cris/arch-v10/kernel/head.S @@ -1,186 +1,10 @@ -/* $Id: head.S,v 1.10 2005/06/20 05:12:54 starvik Exp $ - * +/* * Head of the kernel - alter with care * * Copyright (C) 2000, 2001 Axis Communications AB * * Authors: Bjorn Wesen (bjornw@axis.com) * - * $Log: head.S,v $ - * Revision 1.10 2005/06/20 05:12:54 starvik - * Remove unnecessary diff to kernel.org tree - * - * Revision 1.9 2004/12/13 12:21:51 starvik - * Added I/O and DMA allocators from Linux 2.4 - * - * Revision 1.8 2004/11/22 11:41:14 starvik - * Kernel command line may be supplied to kernel. Not used by Axis but may - * be used by customers. - * - * Revision 1.7 2004/05/14 07:58:01 starvik - * Merge of changes from 2.4 - * - * Revision 1.6 2003/04/28 05:31:46 starvik - * Added section attributes - * - * Revision 1.5 2002/12/11 15:42:02 starvik - * Extracted v10 (ETRAX 100LX) specific stuff from arch/cris/kernel/*.c - * - * Revision 1.4 2002/11/07 09:00:44 starvik - * Names changed for init sections - * init_task_union -> init_thread_union - * - * Revision 1.3 2002/02/05 15:38:23 bjornw - * Oops.. non-CRAMFS_MAGIC should jump over the copying, not into it... - * - * Revision 1.2 2001/12/18 13:35:19 bjornw - * Applied the 2.4.13->2.4.16 CRIS patch to 2.5.1 (is a copy of 2.4.15). - * - * Revision 1.43 2001/11/08 15:09:43 starvik - * Only start MII clock if Ethernet is configured - * - * Revision 1.42 2001/11/08 14:37:34 starvik - * Start MII clock early to make sure that it is running at tranceiver reset - * - * Revision 1.41 2001/10/29 14:55:58 pkj - * Corrected pa$r0 to par0. - * - * Revision 1.40 2001/10/03 14:59:57 pkj - * Added support for resetting the Bluetooth hardware. - * - * Revision 1.39 2001/10/01 14:45:03 bjornw - * Removed underscores and added register prefixes - * - * Revision 1.38 2001/09/21 07:14:11 jonashg - * Made root filesystem (cramfs) use mtdblock driver when booting from flash. - * - * Revision 1.37 2001/09/11 13:44:29 orjanf - * Decouple usage of serial ports for debug and kgdb. - * - * Revision 1.36 2001/06/29 12:39:31 pkj - * Added support for mirroring the first flash to just below the - * second one, to make them look consecutive to cramfs. - * - * Revision 1.35 2001/06/25 14:07:00 hp - * Fix review comment. - * * head.S: Use IO_STATE, IO_FIELD and IO_MASK constructs instead of - * magic numbers. Add comment that -traditional must not be used. - * * entry.S (SYMBOL_NAME): Change redefinition to use ## concatenation. - * Correct and update comment. - * * Makefile (.S.o): Don't use -traditional. Add comment why the - * toplevel rule can't be used (now that there's a reason). - * - * Revision 1.34 2001/05/15 07:08:14 hp - * Tweak "notice" to reflect that both r8 r9 are used - * - * Revision 1.33 2001/05/15 06:40:05 hp - * Put bulk of code in .text.init, data in .data.init - * - * Revision 1.32 2001/05/15 06:18:56 hp - * Execute review comment: s/bcc/bhs/g; s/bcs/blo/g - * - * Revision 1.31 2001/05/15 06:08:40 hp - * Add sentence about autodetecting the bit31-MMU-bug - * - * Revision 1.30 2001/05/15 06:00:05 hp - * Update comment: LOW_MAP is not forced on xsim anymore. - * - * Revision 1.29 2001/04/18 12:51:59 orjanf - * * Reverted review change regarding the use of bcs/bcc. - * * Removed non-working LED-clearing code. - * - * Revision 1.28 2001/04/17 13:58:39 orjanf - * * Renamed CONFIG_KGDB to CONFIG_ETRAX_KGDB. - * - * Revision 1.27 2001/04/17 11:42:35 orjanf - * Changed according to review: - * * Added comment explaining memory map bug. - * * Changed bcs and bcc to blo and bhs, respectively. - * * Removed mentioning of Stallone and Olga boards. - * - * Revision 1.26 2001/04/06 12:31:07 jonashg - * Check for cramfs in flash before RAM instead of RAM before flash. - * - * Revision 1.25 2001/04/04 06:23:53 starvik - * Initialize DRAM if not already initialized - * - * Revision 1.24 2001/04/03 11:12:00 starvik - * Removed dram init (done by rescue or etrax100boot - * Corrected include - * - * Revision 1.23 2001/04/03 09:53:03 starvik - * Include hw_settings.S - * - * Revision 1.22 2001/03/26 14:23:26 bjornw - * Namechange of some config options - * - * Revision 1.21 2001/03/08 12:14:41 bjornw - * * Config name for ETRAX IDE was renamed - * * Removed G27 auto-setting when JULIETTE is chosen (need to make this - * a new config option later) - * - * Revision 1.20 2001/02/23 12:47:56 bjornw - * MMU regs during LOW_MAP updated to reflect a newer reality - * - * Revision 1.19 2001/02/19 11:12:07 bjornw - * Changed comment header format - * - * Revision 1.18 2001/02/15 07:25:38 starvik - * Added support for synchronous serial ports - * - * Revision 1.17 2001/02/08 15:53:13 starvik - * Last commit removed some important ifdefs - * - * Revision 1.16 2001/02/08 15:20:38 starvik - * Include dram_init.S as inline - * - * Revision 1.15 2001/01/29 18:12:01 bjornw - * Corrected some comments - * - * Revision 1.14 2001/01/29 13:11:29 starvik - * Include dram_init.S (with DRAM/SDRAM initialization) - * - * Revision 1.13 2001/01/23 14:54:57 markusl - * Updated for USB - * i.e. added r_gen_config settings - * - * Revision 1.12 2001/01/19 16:16:29 perf - * Added temporary mapping of 0x0c->0x0c to avoid flash loading confusion. - * Renamed serial options from ETRAX100 to ETRAX. - * - * Revision 1.11 2001/01/16 16:31:38 bjornw - * * Changed name and semantics of running_from_flash to romfs_in_flash, - * set by head.S to indicate to setup.c whether there is a cramfs image - * after the kernels BSS or not. Should work for all three boot-cases - * (DRAM with cramfs in DRAM, DRAM with cramfs in flash (compressed boot), - * and flash with cramfs in flash) - * - * Revision 1.10 2001/01/16 14:12:21 bjornw - * * Check for cramfs start passed in r9 from the decompressor, if all other - * cramfs options fail (if we boot from DRAM but don't find a cramfs image - * after the kernel in DRAM, it is probably still in the flash) - * * Check magic in cramfs detection when booting from flash directly - * - * Revision 1.9 2001/01/15 17:17:02 bjornw - * * Corrected the code that detects the cramfs lengths - * * Added a comment saying that the above does not work due to other - * reasons.. - * - * Revision 1.8 2001/01/15 16:27:51 jonashg - * Made boot after flashing work. - * * end destination is __vmlinux_end in RAM. - * * _romfs_start moved because of virtual memory. - * - * Revision 1.7 2000/11/21 13:55:29 bjornw - * Use CONFIG_CRIS_LOW_MAP for the low VM map instead of explicit CPU type - * - * Revision 1.6 2000/10/06 12:36:55 bjornw - * Forgot swapper_pg_dir when changing memory map.. - * - * Revision 1.5 2000/10/04 16:49:30 bjornw - * * Fixed memory mapping in LX - * * Check for cramfs instead of romfs - * */ #define ASSEMBLER_MACROS_ONLY @@ -595,11 +419,17 @@ no_command_line: moveq 0,$r0 + ;; Select or disable serial port 2 +#ifdef CONFIG_ETRAX_SERIAL_PORT2 + or.d IO_STATE (R_GEN_CONFIG, ser2, select),$r0 +#else + or.d IO_STATE (R_GEN_CONFIG, ser2, disable),$r0 +#endif + ;; Init interfaces (disable them). or.d IO_STATE (R_GEN_CONFIG, scsi0, disable) \ | IO_STATE (R_GEN_CONFIG, ata, disable) \ | IO_STATE (R_GEN_CONFIG, par0, disable) \ - | IO_STATE (R_GEN_CONFIG, ser2, disable) \ | IO_STATE (R_GEN_CONFIG, mio, disable) \ | IO_STATE (R_GEN_CONFIG, scsi1, disable) \ | IO_STATE (R_GEN_CONFIG, scsi0w, disable) \ @@ -801,6 +631,41 @@ no_command_line: | IO_STATE (R_SERIAL1_TR_CTRL, tr_bitnr, tr_8bit),$r0 move.b $r0,[R_SERIAL1_TR_CTRL] +#ifdef CONFIG_ETRAX_SERIAL_PORT2 + ;; setup the serial port 2 at 115200 baud for debug purposes + + moveq IO_STATE (R_SERIAL2_XOFF, tx_stop, enable) \ + | IO_STATE (R_SERIAL2_XOFF, auto_xoff, disable) \ + | IO_FIELD (R_SERIAL2_XOFF, xoff_char, 0),$r0 + move.d $r0,[R_SERIAL2_XOFF] + + ; 115.2kbaud for both transmit and receive + move.b IO_STATE (R_SERIAL2_BAUD, tr_baud, c115k2Hz) \ + | IO_STATE (R_SERIAL2_BAUD, rec_baud, c115k2Hz),$r0 + move.b $r0,[R_SERIAL2_BAUD] + + ; Set up and enable the serial2 receiver. + move.b IO_STATE (R_SERIAL2_REC_CTRL, dma_err, stop) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_enable, enable) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rts_, active) \ + | IO_STATE (R_SERIAL2_REC_CTRL, sampling, middle) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_stick_par, normal) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_par, even) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_par_en, disable) \ + | IO_STATE (R_SERIAL2_REC_CTRL, rec_bitnr, rec_8bit),$r0 + move.b $r0,[R_SERIAL2_REC_CTRL] + + ; Set up and enable the serial2 transmitter. + move.b IO_FIELD (R_SERIAL2_TR_CTRL, txd, 0) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_enable, enable) \ + | IO_STATE (R_SERIAL2_TR_CTRL, auto_cts, disabled) \ + | IO_STATE (R_SERIAL2_TR_CTRL, stop_bits, one_bit) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_stick_par, normal) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_par, even) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_par_en, disable) \ + | IO_STATE (R_SERIAL2_TR_CTRL, tr_bitnr, tr_8bit),$r0 + move.b $r0,[R_SERIAL2_TR_CTRL] +#endif #ifdef CONFIG_ETRAX_SERIAL_PORT3 ;; setup the serial port 3 at 115200 baud for debug purposes diff --git a/arch/cris/arch-v10/kernel/io_interface_mux.c b/arch/cris/arch-v10/kernel/io_interface_mux.c index f3b327d4ed9c..add98e0941b5 100644 --- a/arch/cris/arch-v10/kernel/io_interface_mux.c +++ b/arch/cris/arch-v10/kernel/io_interface_mux.c @@ -1,10 +1,9 @@ /* IO interface mux allocator for ETRAX100LX. - * Copyright 2004, Axis Communications AB - * $Id: io_interface_mux.c,v 1.2 2004/12/21 12:08:38 starvik Exp $ + * Copyright 2004-2007, Axis Communications AB */ -/* C.f. ETRAX100LX Designer's Reference 20.9 */ +/* C.f. ETRAX100LX Designer's Reference chapter 19.9 */ #include <linux/kernel.h> #include <linux/slab.h> @@ -45,17 +44,39 @@ struct watcher struct if_group { enum io_if_group group; - unsigned char used; - enum cris_io_interface owner; + /* name - the name of the group 'A' to 'F' */ + char *name; + /* used - a bit mask of all pins in the group in the order listed + * in the tables in 19.9.1 to 19.9.6. Note that no + * distinction is made between in, out and in/out pins. */ + unsigned int used; }; struct interface { enum cris_io_interface ioif; + /* name - the name of the interface */ + char *name; + /* groups - OR'ed together io_if_group flags describing what pin groups + * the interface uses pins in. */ unsigned char groups; + /* used - set when the interface is allocated. */ unsigned char used; char *owner; + /* group_a through group_f - bit masks describing what pins in the + * pin groups the interface uses. */ + unsigned int group_a; + unsigned int group_b; + unsigned int group_c; + unsigned int group_d; + unsigned int group_e; + unsigned int group_f; + + /* gpio_g_in, gpio_g_out, gpio_b - bit masks telling what pins in the + * GPIO ports the interface uses. This could be reconstucted using + * the group_X masks and a table of what pins the GPIO ports use, + * but that would be messy. */ unsigned int gpio_g_in; unsigned int gpio_g_out; unsigned char gpio_b; @@ -64,26 +85,32 @@ struct interface static struct if_group if_groups[6] = { { .group = group_a, + .name = "A", .used = 0, }, { .group = group_b, + .name = "B", .used = 0, }, { .group = group_c, + .name = "C", .used = 0, }, { .group = group_d, + .name = "D", .used = 0, }, { .group = group_e, + .name = "E", .used = 0, }, { .group = group_f, + .name = "F", .used = 0, } }; @@ -94,14 +121,32 @@ static struct interface interfaces[] = { /* Begin Non-multiplexed interfaces */ { .ioif = if_eth, + .name = "ethernet", .groups = 0, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0, .gpio_g_out = 0, .gpio_b = 0 }, { .ioif = if_serial_0, + .name = "serial_0", .groups = 0, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0, .gpio_g_out = 0, .gpio_b = 0 @@ -109,172 +154,385 @@ static struct interface interfaces[] = { /* End Non-multiplexed interfaces */ { .ioif = if_serial_1, + .name = "serial_1", .groups = group_e, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0x0f, + .group_f = 0, + .gpio_g_in = 0x00000000, .gpio_g_out = 0x00000000, .gpio_b = 0x00 }, { .ioif = if_serial_2, + .name = "serial_2", .groups = group_b, + + .group_a = 0, + .group_b = 0x0f, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x000000c0, .gpio_g_out = 0x000000c0, .gpio_b = 0x00 }, { .ioif = if_serial_3, + .name = "serial_3", .groups = group_c, + + .group_a = 0, + .group_b = 0, + .group_c = 0x0f, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0xc0000000, .gpio_g_out = 0xc0000000, .gpio_b = 0x00 }, { .ioif = if_sync_serial_1, - .groups = group_e | group_f, /* if_sync_serial_1 and if_sync_serial_3 - can be used simultaneously */ + .name = "sync_serial_1", + .groups = group_e | group_f, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0x0f, + .group_f = 0x10, + .gpio_g_in = 0x00000000, .gpio_g_out = 0x00000000, .gpio_b = 0x10 }, { .ioif = if_sync_serial_3, + .name = "sync_serial_3", .groups = group_c | group_f, + + .group_a = 0, + .group_b = 0, + .group_c = 0x0f, + .group_d = 0, + .group_e = 0, + .group_f = 0x80, + .gpio_g_in = 0xc0000000, .gpio_g_out = 0xc0000000, .gpio_b = 0x80 }, { .ioif = if_shared_ram, + .name = "shared_ram", .groups = group_a, + + .group_a = 0x7f8ff, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x0000ff3e, .gpio_g_out = 0x0000ff38, .gpio_b = 0x00 }, { .ioif = if_shared_ram_w, + .name = "shared_ram_w", .groups = group_a | group_d, + + .group_a = 0x7f8ff, + .group_b = 0, + .group_c = 0, + .group_d = 0xff, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x00ffff3e, .gpio_g_out = 0x00ffff38, .gpio_b = 0x00 }, { .ioif = if_par_0, + .name = "par_0", .groups = group_a, + + .group_a = 0x7fbff, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x0000ff3e, .gpio_g_out = 0x0000ff3e, .gpio_b = 0x00 }, { .ioif = if_par_1, + .name = "par_1", .groups = group_d, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0x7feff, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x3eff0000, .gpio_g_out = 0x3eff0000, .gpio_b = 0x00 }, { .ioif = if_par_w, + .name = "par_w", .groups = group_a | group_d, + + .group_a = 0x7fbff, + .group_b = 0, + .group_c = 0, + .group_d = 0xff, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x00ffff3e, .gpio_g_out = 0x00ffff3e, .gpio_b = 0x00 }, { .ioif = if_scsi8_0, - .groups = group_a | group_b | group_f, /* if_scsi8_0 and if_scsi8_1 - can be used simultaneously */ + .name = "scsi8_0", + .groups = group_a | group_b | group_f, + + .group_a = 0x7ffff, + .group_b = 0x0f, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0x10, + .gpio_g_in = 0x0000ffff, .gpio_g_out = 0x0000ffff, .gpio_b = 0x10 }, { .ioif = if_scsi8_1, - .groups = group_c | group_d | group_f, /* if_scsi8_0 and if_scsi8_1 - can be used simultaneously */ + .name = "scsi8_1", + .groups = group_c | group_d | group_f, + + .group_a = 0, + .group_b = 0, + .group_c = 0x0f, + .group_d = 0x7ffff, + .group_e = 0, + .group_f = 0x80, + .gpio_g_in = 0xffff0000, .gpio_g_out = 0xffff0000, .gpio_b = 0x80 }, { .ioif = if_scsi_w, + .name = "scsi_w", .groups = group_a | group_b | group_d | group_f, + + .group_a = 0x7ffff, + .group_b = 0x0f, + .group_c = 0, + .group_d = 0x601ff, + .group_e = 0, + .group_f = 0x90, + .gpio_g_in = 0x01ffffff, .gpio_g_out = 0x07ffffff, .gpio_b = 0x80 }, { .ioif = if_ata, + .name = "ata", .groups = group_a | group_b | group_c | group_d, + + .group_a = 0x7ffff, + .group_b = 0x0f, + .group_c = 0x0f, + .group_d = 0x7cfff, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0xf9ffffff, .gpio_g_out = 0xffffffff, .gpio_b = 0x80 }, { .ioif = if_csp, - .groups = group_f, /* if_csp and if_i2c can be used simultaneously */ + .name = "csp", + .groups = group_f, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0xfc, + .gpio_g_in = 0x00000000, .gpio_g_out = 0x00000000, .gpio_b = 0xfc }, { .ioif = if_i2c, - .groups = group_f, /* if_csp and if_i2c can be used simultaneously */ + .name = "i2c", + .groups = group_f, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0x03, + .gpio_g_in = 0x00000000, .gpio_g_out = 0x00000000, .gpio_b = 0x03 }, { .ioif = if_usb_1, + .name = "usb_1", .groups = group_e | group_f, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0x0f, + .group_f = 0x2c, + .gpio_g_in = 0x00000000, .gpio_g_out = 0x00000000, .gpio_b = 0x2c }, { .ioif = if_usb_2, + .name = "usb_2", .groups = group_d, - .gpio_g_in = 0x0e000000, - .gpio_g_out = 0x3c000000, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0x33e00, + .group_f = 0, + + .gpio_g_in = 0x3e000000, + .gpio_g_out = 0x0c000000, .gpio_b = 0x00 }, /* GPIO pins */ { .ioif = if_gpio_grp_a, + .name = "gpio_a", .groups = group_a, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x0000ff3f, .gpio_g_out = 0x0000ff3f, .gpio_b = 0x00 }, { .ioif = if_gpio_grp_b, + .name = "gpio_b", .groups = group_b, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x000000c0, .gpio_g_out = 0x000000c0, .gpio_b = 0x00 }, { .ioif = if_gpio_grp_c, + .name = "gpio_c", .groups = group_c, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0xc0000000, .gpio_g_out = 0xc0000000, .gpio_b = 0x00 }, { .ioif = if_gpio_grp_d, + .name = "gpio_d", .groups = group_d, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x3fff0000, .gpio_g_out = 0x3fff0000, .gpio_b = 0x00 }, { .ioif = if_gpio_grp_e, + .name = "gpio_e", .groups = group_e, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x00000000, .gpio_g_out = 0x00000000, .gpio_b = 0x00 }, { .ioif = if_gpio_grp_f, + .name = "gpio_f", .groups = group_f, + + .group_a = 0, + .group_b = 0, + .group_c = 0, + .group_d = 0, + .group_e = 0, + .group_f = 0, + .gpio_g_in = 0x00000000, .gpio_g_out = 0x00000000, .gpio_b = 0xff @@ -284,11 +542,13 @@ static struct interface interfaces[] = { static struct watcher *watchers = NULL; +/* The pins that are free to use in the GPIO ports. */ static unsigned int gpio_in_pins = 0xffffffff; static unsigned int gpio_out_pins = 0xffffffff; static unsigned char gpio_pb_pins = 0xff; static unsigned char gpio_pa_pins = 0xff; +/* Identifiers for the owners of the GPIO pins. */ static enum cris_io_interface gpio_pa_owners[8]; static enum cris_io_interface gpio_pb_owners[8]; static enum cris_io_interface gpio_pg_owners[32]; @@ -338,13 +598,15 @@ int cris_request_io_interface(enum cris_io_interface ioif, const char *device_id struct if_group *grp; unsigned char group_set; unsigned long flags; + int res = 0; (void)cris_io_interface_init(); DBG(printk("cris_request_io_interface(%d, \"%s\")\n", ioif, device_id)); if ((ioif >= if_max_interfaces) || (ioif < 0)) { - printk(KERN_CRIT "cris_request_io_interface: Bad interface %u submitted for %s\n", + printk(KERN_CRIT "cris_request_io_interface: Bad interface " + "%u submitted for %s\n", ioif, device_id); return -EINVAL; @@ -353,59 +615,69 @@ int cris_request_io_interface(enum cris_io_interface ioif, const char *device_id local_irq_save(flags); if (interfaces[ioif].used) { - local_irq_restore(flags); - printk(KERN_CRIT "cris_io_interface: Cannot allocate interface for %s, in use by %s\n", + printk(KERN_CRIT "cris_io_interface: Cannot allocate interface " + "%s for %s, in use by %s\n", + interfaces[ioif].name, device_id, interfaces[ioif].owner); - return -EBUSY; + res = -EBUSY; + goto exit; } - /* Check that all required groups are free before allocating, */ + /* Check that all required pins in the used groups are free + * before allocating. */ group_set = interfaces[ioif].groups; while (NULL != (grp = get_group(group_set))) { - if (grp->used) { - if (grp->group == group_f) { - if ((if_sync_serial_1 == ioif) || - (if_sync_serial_3 == ioif)) { - if ((grp->owner != if_sync_serial_1) && - (grp->owner != if_sync_serial_3)) { - local_irq_restore(flags); - return -EBUSY; - } - } else if ((if_scsi8_0 == ioif) || - (if_scsi8_1 == ioif)) { - if ((grp->owner != if_scsi8_0) && - (grp->owner != if_scsi8_1)) { - local_irq_restore(flags); - return -EBUSY; - } - } - } else { - local_irq_restore(flags); - return -EBUSY; - } + unsigned int if_group_use = 0; + + switch (grp->group) { + case group_a: + if_group_use = interfaces[ioif].group_a; + break; + case group_b: + if_group_use = interfaces[ioif].group_b; + break; + case group_c: + if_group_use = interfaces[ioif].group_c; + break; + case group_d: + if_group_use = interfaces[ioif].group_d; + break; + case group_e: + if_group_use = interfaces[ioif].group_e; + break; + case group_f: + if_group_use = interfaces[ioif].group_f; + break; + default: + BUG_ON(1); } + + if (if_group_use & grp->used) { + printk(KERN_INFO "cris_request_io_interface: group " + "%s needed by %s not available\n", + grp->name, interfaces[ioif].name); + res = -EBUSY; + goto exit; + } + group_set = clear_group_from_set(group_set, grp); } /* Are the required GPIO pins available too? */ - if (((interfaces[ioif].gpio_g_in & gpio_in_pins) != interfaces[ioif].gpio_g_in) || - ((interfaces[ioif].gpio_g_out & gpio_out_pins) != interfaces[ioif].gpio_g_out) || - ((interfaces[ioif].gpio_b & gpio_pb_pins) != interfaces[ioif].gpio_b)) { - local_irq_restore(flags); - printk(KERN_CRIT "cris_request_io_interface: Could not get required pins for interface %u\n", - ioif); - return -EBUSY; - } - - /* All needed I/O pins and pin groups are free, allocate. */ - group_set = interfaces[ioif].groups; - while (NULL != (grp = get_group(group_set))) { - grp->used = 1; - grp->owner = ioif; - group_set = clear_group_from_set(group_set, grp); + if (((interfaces[ioif].gpio_g_in & gpio_in_pins) != + interfaces[ioif].gpio_g_in) || + ((interfaces[ioif].gpio_g_out & gpio_out_pins) != + interfaces[ioif].gpio_g_out) || + ((interfaces[ioif].gpio_b & gpio_pb_pins) != + interfaces[ioif].gpio_b)) { + printk(KERN_CRIT "cris_request_io_interface: Could not get " + "required pins for interface %u\n", ioif); + res = -EBUSY; + goto exit; } + /* Check which registers need to be reconfigured. */ gens = genconfig_shadow; gens_ii = gen_config_ii_shadow; @@ -495,9 +767,43 @@ int cris_request_io_interface(enum cris_io_interface ioif, const char *device_id set_gen_config = 0; break; default: - panic("cris_request_io_interface: Bad interface %u submitted for %s\n", - ioif, - device_id); + printk(KERN_INFO "cris_request_io_interface: Bad interface " + "%u submitted for %s\n", + ioif, device_id); + res = -EBUSY; + goto exit; + } + + /* All needed I/O pins and pin groups are free, allocate. */ + group_set = interfaces[ioif].groups; + while (NULL != (grp = get_group(group_set))) { + unsigned int if_group_use = 0; + + switch (grp->group) { + case group_a: + if_group_use = interfaces[ioif].group_a; + break; + case group_b: + if_group_use = interfaces[ioif].group_b; + break; + case group_c: + if_group_use = interfaces[ioif].group_c; + break; + case group_d: + if_group_use = interfaces[ioif].group_d; + break; + case group_e: + if_group_use = interfaces[ioif].group_e; + break; + case group_f: + if_group_use = interfaces[ioif].group_f; + break; + default: + BUG_ON(1); + } + grp->used |= if_group_use; + + group_set = clear_group_from_set(group_set, grp); } interfaces[ioif].used = 1; @@ -516,25 +822,28 @@ int cris_request_io_interface(enum cris_io_interface ioif, const char *device_id *R_GEN_CONFIG_II = gen_config_ii_shadow; } - DBG(printk("GPIO pins: available before: g_in=0x%08x g_out=0x%08x pb=0x%02x\n", - gpio_in_pins, gpio_out_pins, gpio_pb_pins)); - DBG(printk("grabbing pins: g_in=0x%08x g_out=0x%08x pb=0x%02x\n", - interfaces[ioif].gpio_g_in, - interfaces[ioif].gpio_g_out, - interfaces[ioif].gpio_b)); + DBG(printk(KERN_DEBUG "GPIO pins: available before: " + "g_in=0x%08x g_out=0x%08x pb=0x%02x\n", + gpio_in_pins, gpio_out_pins, gpio_pb_pins)); + DBG(printk(KERN_DEBUG + "grabbing pins: g_in=0x%08x g_out=0x%08x pb=0x%02x\n", + interfaces[ioif].gpio_g_in, + interfaces[ioif].gpio_g_out, + interfaces[ioif].gpio_b)); gpio_in_pins &= ~interfaces[ioif].gpio_g_in; gpio_out_pins &= ~interfaces[ioif].gpio_g_out; gpio_pb_pins &= ~interfaces[ioif].gpio_b; - DBG(printk("GPIO pins: available after: g_in=0x%08x g_out=0x%08x pb=0x%02x\n", - gpio_in_pins, gpio_out_pins, gpio_pb_pins)); + DBG(printk(KERN_DEBUG "GPIO pins: available after: " + "g_in=0x%08x g_out=0x%08x pb=0x%02x\n", + gpio_in_pins, gpio_out_pins, gpio_pb_pins)); +exit: local_irq_restore(flags); - - notify_watchers(); - - return 0; + if (res == 0) + notify_watchers(); + return res; } @@ -560,43 +869,35 @@ void cris_free_io_interface(enum cris_io_interface ioif) } group_set = interfaces[ioif].groups; while (NULL != (grp = get_group(group_set))) { - if (grp->group == group_f) { - switch (ioif) - { - case if_sync_serial_1: - if ((grp->owner == if_sync_serial_1) && - interfaces[if_sync_serial_3].used) { - grp->owner = if_sync_serial_3; - } else - grp->used = 0; - break; - case if_sync_serial_3: - if ((grp->owner == if_sync_serial_3) && - interfaces[if_sync_serial_1].used) { - grp->owner = if_sync_serial_1; - } else - grp->used = 0; - break; - case if_scsi8_0: - if ((grp->owner == if_scsi8_0) && - interfaces[if_scsi8_1].used) { - grp->owner = if_scsi8_1; - } else - grp->used = 0; - break; - case if_scsi8_1: - if ((grp->owner == if_scsi8_1) && - interfaces[if_scsi8_0].used) { - grp->owner = if_scsi8_0; - } else - grp->used = 0; - break; - default: - grp->used = 0; - } - } else { - grp->used = 0; + unsigned int if_group_use = 0; + + switch (grp->group) { + case group_a: + if_group_use = interfaces[ioif].group_a; + break; + case group_b: + if_group_use = interfaces[ioif].group_b; + break; + case group_c: + if_group_use = interfaces[ioif].group_c; + break; + case group_d: + if_group_use = interfaces[ioif].group_d; + break; + case group_e: + if_group_use = interfaces[ioif].group_e; + break; + case group_f: + if_group_use = interfaces[ioif].group_f; + break; + default: + BUG_ON(1); } + + if ((grp->used & if_group_use) != if_group_use) + BUG_ON(1); + grp->used = grp->used & ~if_group_use; + group_set = clear_group_from_set(group_set, grp); } interfaces[ioif].used = 0; diff --git a/arch/cris/arch-v10/kernel/irq.c b/arch/cris/arch-v10/kernel/irq.c index e06ab0050d37..65ed803dae6f 100644 --- a/arch/cris/arch-v10/kernel/irq.c +++ b/arch/cris/arch-v10/kernel/irq.c @@ -1,5 +1,4 @@ -/* $Id: irq.c,v 1.4 2005/01/04 12:22:28 starvik Exp $ - * +/* * linux/arch/cris/kernel/irq.c * * Copyright (c) 2000-2002 Axis Communications AB @@ -18,10 +17,6 @@ #include <linux/kernel.h> #include <linux/init.h> -/* From kgdb.c. */ -extern void kgdb_init(void); -extern void breakpoint(void); - #define mask_irq(irq_nr) (*R_VECT_MASK_CLR = 1 << (irq_nr)); #define unmask_irq(irq_nr) (*R_VECT_MASK_SET = 1 << (irq_nr)); diff --git a/arch/cris/arch-v10/kernel/kgdb.c b/arch/cris/arch-v10/kernel/kgdb.c index 77f4b1423725..a3ca55150745 100644 --- a/arch/cris/arch-v10/kernel/kgdb.c +++ b/arch/cris/arch-v10/kernel/kgdb.c @@ -17,66 +17,8 @@ *! Jun 17 1999 Hendrik Ruijter Added gdb 4.18 support. 'X', 'qC' and 'qL'. *! Jul 21 1999 Bjorn Wesen eLinux port *! -*! $Log: kgdb.c,v $ -*! Revision 1.6 2005/01/14 10:12:17 starvik -*! KGDB on separate port. -*! Console fixes from 2.4. -*! -*! Revision 1.5 2004/10/07 13:59:08 starvik -*! Corrected call to set_int_vector -*! -*! Revision 1.4 2003/04/09 05:20:44 starvik -*! Merge of Linux 2.5.67 -*! -*! Revision 1.3 2003/01/21 19:11:08 starvik -*! Modified include path for new dir layout -*! -*! Revision 1.2 2002/11/19 14:35:24 starvik -*! Changes from linux 2.4 -*! Changed struct initializer syntax to the currently preferred notation -*! -*! Revision 1.1 2001/12/17 13:59:27 bjornw -*! Initial revision -*! -*! Revision 1.6 2001/10/09 13:10:03 matsfg -*! Added $ on registers and removed some underscores -*! -*! Revision 1.5 2001/04/17 13:58:39 orjanf -*! * Renamed CONFIG_KGDB to CONFIG_ETRAX_KGDB. -*! -*! Revision 1.4 2001/02/23 13:45:19 bjornw -*! config.h check -*! -*! Revision 1.3 2001/01/31 18:08:23 orjanf -*! Removed kgdb_handle_breakpoint from being the break 8 handler. -*! -*! Revision 1.2 2001/01/12 14:22:25 orjanf -*! Updated kernel debugging support to work with ETRAX 100LX. -*! -*! Revision 1.1 2000/07/10 16:25:21 bjornw -*! Initial revision -*! -*! Revision 1.1.1.1 1999/12/03 14:57:31 bjornw -*! * Initial version of arch/cris, the latest CRIS architecture with an MMU. -*! Mostly copied from arch/etrax100 with appropriate renames of files. -*! The mm/ subdir is copied from arch/i386. -*! This does not compile yet at all. -*! -*! -*! Revision 1.4 1999/07/22 17:25:25 bjornw -*! Dont wait for + in putpacket if we havent hit the initial breakpoint yet. Added a kgdb_init function which sets up the break and irq vectors. -*! -*! Revision 1.3 1999/07/21 19:51:18 bjornw -*! Check if the interrupting char is a ctrl-C, ignore otherwise. -*! -*! Revision 1.2 1999/07/21 18:09:39 bjornw -*! Ported to eLinux architecture, and added some kgdb documentation. -*! -*! *!--------------------------------------------------------------------------- *! -*! $Id: kgdb.c,v 1.6 2005/01/14 10:12:17 starvik Exp $ -*! *! (C) Copyright 1999, Axis Communications AB, LUND, SWEDEN *! *!**************************************************************************/ diff --git a/arch/cris/arch-v10/kernel/process.c b/arch/cris/arch-v10/kernel/process.c index 1a3760c94f85..53117f07cc1a 100644 --- a/arch/cris/arch-v10/kernel/process.c +++ b/arch/cris/arch-v10/kernel/process.c @@ -1,5 +1,4 @@ -/* $Id: process.c,v 1.12 2004/12/27 11:18:32 starvik Exp $ - * +/* * linux/arch/cris/kernel/process.c * * Copyright (C) 1995 Linus Torvalds diff --git a/arch/cris/arch-v10/kernel/ptrace.c b/arch/cris/arch-v10/kernel/ptrace.c index b570ae9b6cad..ee505b2eb4db 100644 --- a/arch/cris/arch-v10/kernel/ptrace.c +++ b/arch/cris/arch-v10/kernel/ptrace.c @@ -65,6 +65,7 @@ void ptrace_disable(struct task_struct *child) { /* Todo - pending singlesteps? */ + clear_tsk_thread_flag(child, TIF_SYSCALL_TRACE); } /* diff --git a/arch/cris/arch-v10/kernel/shadows.c b/arch/cris/arch-v10/kernel/shadows.c index 326178aef6ee..2454a0b02f54 100644 --- a/arch/cris/arch-v10/kernel/shadows.c +++ b/arch/cris/arch-v10/kernel/shadows.c @@ -1,5 +1,4 @@ -/* $Id: shadows.c,v 1.2 2004/12/13 12:21:51 starvik Exp $ - * +/* * Various shadow registers. Defines for these are in include/asm-etrax100/io.h */ diff --git a/arch/cris/arch-v10/kernel/traps.c b/arch/cris/arch-v10/kernel/traps.c index 4becc1bcced9..9eada5d8893b 100644 --- a/arch/cris/arch-v10/kernel/traps.c +++ b/arch/cris/arch-v10/kernel/traps.c @@ -1,13 +1,10 @@ -/* $Id: traps.c,v 1.4 2005/04/24 18:47:55 starvik Exp $ +/* + * Helper functions for trap handlers * - * linux/arch/cris/arch-v10/traps.c + * Copyright (C) 2000-2007, Axis Communications AB. * - * Heler functions for trap handlers - * - * Copyright (C) 2000-2002 Axis Communications AB - * - * Authors: Bjorn Wesen - * Hans-Peter Nilsson + * Authors: Bjorn Wesen + * Hans-Peter Nilsson * */ @@ -15,124 +12,119 @@ #include <asm/uaccess.h> #include <asm/arch/sv_addr_ag.h> -extern int raw_printk(const char *fmt, ...); - -void -show_registers(struct pt_regs * regs) +void +show_registers(struct pt_regs *regs) { - /* We either use rdusp() - the USP register, which might not - correspond to the current process for all cases we're called, - or we use the current->thread.usp, which is not up to date for - the current process. Experience shows we want the USP - register. */ + /* + * It's possible to use either the USP register or current->thread.usp. + * USP might not correspond to the current process for all cases this + * function is called, and current->thread.usp isn't up to date for the + * current process. Experience shows that using USP is the way to go. + */ unsigned long usp = rdusp(); - raw_printk("IRP: %08lx SRP: %08lx DCCR: %08lx USP: %08lx MOF: %08lx\n", - regs->irp, regs->srp, regs->dccr, usp, regs->mof ); - raw_printk(" r0: %08lx r1: %08lx r2: %08lx r3: %08lx\n", + printk("IRP: %08lx SRP: %08lx DCCR: %08lx USP: %08lx MOF: %08lx\n", + regs->irp, regs->srp, regs->dccr, usp, regs->mof); + + printk(" r0: %08lx r1: %08lx r2: %08lx r3: %08lx\n", regs->r0, regs->r1, regs->r2, regs->r3); - raw_printk(" r4: %08lx r5: %08lx r6: %08lx r7: %08lx\n", + + printk(" r4: %08lx r5: %08lx r6: %08lx r7: %08lx\n", regs->r4, regs->r5, regs->r6, regs->r7); - raw_printk(" r8: %08lx r9: %08lx r10: %08lx r11: %08lx\n", + + printk(" r8: %08lx r9: %08lx r10: %08lx r11: %08lx\n", regs->r8, regs->r9, regs->r10, regs->r11); - raw_printk("r12: %08lx r13: %08lx oR10: %08lx sp: %08lx\n", - regs->r12, regs->r13, regs->orig_r10, regs); - raw_printk("R_MMU_CAUSE: %08lx\n", (unsigned long)*R_MMU_CAUSE); - raw_printk("Process %s (pid: %d, stackpage=%08lx)\n", + + printk("r12: %08lx r13: %08lx oR10: %08lx sp: %08lx\n", + regs->r12, regs->r13, regs->orig_r10, (long unsigned)regs); + + printk("R_MMU_CAUSE: %08lx\n", (unsigned long)*R_MMU_CAUSE); + + printk("Process %s (pid: %d, stackpage=%08lx)\n", current->comm, current->pid, (unsigned long)current); /* - * When in-kernel, we also print out the stack and code at the - * time of the fault.. - */ - if (! user_mode(regs)) { - int i; + * When in-kernel, we also print out the stack and code at the + * time of the fault.. + */ + if (!user_mode(regs)) { + int i; - show_stack(NULL, (unsigned long*)usp); + show_stack(NULL, (unsigned long *)usp); - /* Dump kernel stack if the previous dump wasn't one. */ + /* + * If the previous stack-dump wasn't a kernel one, dump the + * kernel stack now. + */ if (usp != 0) - show_stack (NULL, NULL); - - raw_printk("\nCode: "); - if(regs->irp < PAGE_OFFSET) - goto bad; - - /* Often enough the value at regs->irp does not point to - the interesting instruction, which is most often the - _previous_ instruction. So we dump at an offset large - enough that instruction decoding should be in sync at - the interesting point, but small enough to fit on a row - (sort of). We point out the regs->irp location in a - ksymoops-friendly way by wrapping the byte for that - address in parentheses. */ - for(i = -12; i < 12; i++) - { - unsigned char c; - if(__get_user(c, &((unsigned char*)regs->irp)[i])) { -bad: - raw_printk(" Bad IP value."); - break; - } + show_stack(NULL, NULL); + + printk("\nCode: "); + + if (regs->irp < PAGE_OFFSET) + goto bad_value; + + /* + * Quite often the value at regs->irp doesn't point to the + * interesting instruction, which often is the previous + * instruction. So dump at an offset large enough that the + * instruction decoding should be in sync at the interesting + * point, but small enough to fit on a row. The regs->irp + * location is pointed out in a ksymoops-friendly way by + * wrapping the byte for that address in parenthesises. + */ + for (i = -12; i < 12; i++) { + unsigned char c; + + if (__get_user(c, &((unsigned char *)regs->irp)[i])) { +bad_value: + printk(" Bad IP value."); + break; + } if (i == 0) - raw_printk("(%02x) ", c); + printk("(%02x) ", c); else - raw_printk("%02x ", c); - } - raw_printk("\n"); - } + printk("%02x ", c); + } + printk("\n"); + } } -/* Called from entry.S when the watchdog has bitten - * We print out something resembling an oops dump, and if - * we have the nice doggy development flag set, we halt here - * instead of rebooting. - */ - -extern void reset_watchdog(void); -extern void stop_watchdog(void); - - void -watchdog_bite_hook(struct pt_regs *regs) +arch_enable_nmi(void) { -#ifdef CONFIG_ETRAX_WATCHDOG_NICE_DOGGY - local_irq_disable(); - stop_watchdog(); - show_registers(regs); - while(1) /* nothing */; -#else - show_registers(regs); -#endif + asm volatile ("setf m"); } -/* This is normally the 'Oops' routine */ -void -die_if_kernel(const char * str, struct pt_regs * regs, long err) +extern void (*nmi_handler)(struct pt_regs *); +void handle_nmi(struct pt_regs *regs) { - if(user_mode(regs)) - return; - -#ifdef CONFIG_ETRAX_WATCHDOG_NICE_DOGGY - /* This printout might take too long and trigger the - * watchdog normally. If we're in the nice doggy - * development mode, stop the watchdog during printout. - */ - stop_watchdog(); -#endif - - raw_printk("%s: %04lx\n", str, err & 0xffff); - - show_registers(regs); - -#ifdef CONFIG_ETRAX_WATCHDOG_NICE_DOGGY - reset_watchdog(); -#endif - do_exit(SIGSEGV); + if (nmi_handler) + nmi_handler(regs); + + /* Wait until nmi is no longer active. (We enable NMI immediately after + returning from this function, and we don't want it happening while + exiting from the NMI interrupt handler.) */ + while (*R_IRQ_MASK0_RD & IO_STATE(R_IRQ_MASK0_RD, nmi_pin, active)) + ; } -void arch_enable_nmi(void) +#ifdef CONFIG_DEBUG_BUGVERBOSE +void +handle_BUG(struct pt_regs *regs) { - asm volatile("setf m"); + struct bug_frame f; + unsigned char c; + unsigned long irp = regs->irp; + + if (__copy_from_user(&f, (const void __user *)(irp - 8), sizeof f)) + return; + if (f.prefix != BUG_PREFIX || f.magic != BUG_MAGIC) + return; + if (__get_user(c, f.filename)) + f.filename = "<bad filename>"; + + printk("kernel BUG at %s:%d!\n", f.filename, f.line); } +#endif diff --git a/arch/cris/arch-v10/lib/checksum.S b/arch/cris/arch-v10/lib/checksum.S index 85c48f0a9ec2..7d552f4bd5ae 100644 --- a/arch/cris/arch-v10/lib/checksum.S +++ b/arch/cris/arch-v10/lib/checksum.S @@ -1,4 +1,4 @@ -/* $Id: checksum.S,v 1.1 2001/12/17 13:59:27 bjornw Exp $ +/* * A fast checksum routine using movem * Copyright (c) 1998-2001 Axis Communications AB * @@ -61,8 +61,6 @@ _mloop: movem [$r10+],$r9 ; read 10 longwords ax addq 0,$r12 - ax ; do it again, since we might have generated a carry - addq 0,$r12 subq 10*4,$r11 bge _mloop @@ -88,10 +86,6 @@ _word_loop: lsrq 16,$r13 ; r13 = checksum >> 16 and.d $r9,$r12 ; checksum = checksum & 0xffff add.d $r13,$r12 ; checksum += r13 - move.d $r12,$r13 ; do the same again, maybe we got a carry last add - lsrq 16,$r13 - and.d $r9,$r12 - add.d $r13,$r12 _no_fold: cmpq 2,$r11 diff --git a/arch/cris/arch-v10/lib/checksumcopy.S b/arch/cris/arch-v10/lib/checksumcopy.S index 35cbffb306fd..540db8a5f849 100644 --- a/arch/cris/arch-v10/lib/checksumcopy.S +++ b/arch/cris/arch-v10/lib/checksumcopy.S @@ -1,4 +1,4 @@ -/* $Id: checksumcopy.S,v 1.1 2001/12/17 13:59:27 bjornw Exp $ +/* * A fast checksum+copy routine using movem * Copyright (c) 1998, 2001 Axis Communications AB * @@ -67,8 +67,6 @@ _mloop: movem [$r10+],$r9 ; read 10 longwords ax addq 0,$r13 - ax ; do it again, since we might have generated a carry - addq 0,$r13 subq 10*4,$r12 bge _mloop @@ -91,10 +89,6 @@ _word_loop: lsrq 16,$r9 ; r0 = checksum >> 16 and.d 0xffff,$r13 ; checksum = checksum & 0xffff add.d $r9,$r13 ; checksum += r0 - move.d $r13,$r9 ; do the same again, maybe we got a carry last add - lsrq 16,$r9 - and.d 0xffff,$r13 - add.d $r9,$r13 _no_fold: cmpq 2,$r12 diff --git a/arch/cris/arch-v10/lib/dram_init.S b/arch/cris/arch-v10/lib/dram_init.S index 6a6bdfd6984d..b9190ff7d0a4 100644 --- a/arch/cris/arch-v10/lib/dram_init.S +++ b/arch/cris/arch-v10/lib/dram_init.S @@ -1,5 +1,4 @@ -/* $Id: dram_init.S,v 1.4 2003/09/22 09:21:59 starvik Exp $ - * +/* * DRAM/SDRAM initialization - alter with care * This file is intended to be included from other assembler files * @@ -8,60 +7,7 @@ * * Copyright (C) 2000, 2001 Axis Communications AB * - * Authors: Mikael Starvik (starvik@axis.com) - * - * $Log: dram_init.S,v $ - * Revision 1.4 2003/09/22 09:21:59 starvik - * Decompresser is linked to 0x407xxxxx and sdram commands are at 0x000xxxxx - * so we need to mask off 12 bits. - * - * Revision 1.3 2003/03/31 09:38:37 starvik - * Corrected calculation of end of sdram init commands - * - * Revision 1.2 2002/11/19 13:33:29 starvik - * Changes from Linux 2.4 - * - * Revision 1.13 2002/10/30 07:42:28 starvik - * Always read SDRAM command sequence from flash - * - * Revision 1.12 2002/08/09 11:37:37 orjanf - * Added double initialization work-around for Samsung SDRAMs. - * - * Revision 1.11 2002/06/04 11:43:21 starvik - * Check if mrs_data is specified in kernelconfig (necessary for MCM) - * - * Revision 1.10 2001/10/04 12:00:21 martinnn - * Added missing underscores. - * - * Revision 1.9 2001/10/01 14:47:35 bjornw - * Added register prefixes and removed underscores - * - * Revision 1.8 2001/05/15 07:12:45 hp - * Copy warning from head.S about r8 and r9 - * - * Revision 1.7 2001/04/18 12:05:39 bjornw - * Fixed comments, and explicitly include config.h to be sure its there - * - * Revision 1.6 2001/04/10 06:20:16 starvik - * Delay should be 200us, not 200ns - * - * Revision 1.5 2001/04/09 06:01:13 starvik - * Added support for 100 MHz SDRAMs - * - * Revision 1.4 2001/03/26 14:24:01 bjornw - * Namechange of some config options - * - * Revision 1.3 2001/03/23 08:29:41 starvik - * Corrected calculation of mrs_data - * - * Revision 1.2 2001/02/08 15:20:00 starvik - * Corrected SDRAM initialization - * Should now be included as inline - * - * Revision 1.1 2001/01/29 13:08:02 starvik - * Initial version - * This file should be included from all assembler files that needs to - * initialize DRAM/SDRAM. + * Authors: Mikael Starvik (starvik@axis.com) * */ diff --git a/arch/cris/arch-v10/lib/old_checksum.c b/arch/cris/arch-v10/lib/old_checksum.c index 497634a64829..1734b467efa6 100644 --- a/arch/cris/arch-v10/lib/old_checksum.c +++ b/arch/cris/arch-v10/lib/old_checksum.c @@ -1,5 +1,4 @@ -/* $Id: old_checksum.c,v 1.3 2003/10/27 08:04:32 starvik Exp $ - * +/* * INET An implementation of the TCP/IP protocol suite for the LINUX * operating system. INET is implemented using the BSD Socket * interface as the means of communication with the user level. diff --git a/arch/cris/arch-v10/mm/fault.c b/arch/cris/arch-v10/mm/fault.c index fe2615022b97..65504fd80928 100644 --- a/arch/cris/arch-v10/mm/fault.c +++ b/arch/cris/arch-v10/mm/fault.c @@ -4,10 +4,10 @@ * Low level bus fault handler * * - * Copyright (C) 2000, 2001 Axis Communications AB + * Copyright (C) 2000-2007 Axis Communications AB + * + * Authors: Bjorn Wesen * - * Authors: Bjorn Wesen - * */ #include <linux/mm.h> @@ -60,7 +60,7 @@ handle_mmu_bus_fault(struct pt_regs *regs) #ifdef DEBUG page_id = IO_EXTRACT(R_MMU_CAUSE, page_id, cause); acc = IO_EXTRACT(R_MMU_CAUSE, acc_excp, cause); - inv = IO_EXTRACT(R_MMU_CAUSE, inv_excp, cause); + inv = IO_EXTRACT(R_MMU_CAUSE, inv_excp, cause); index = IO_EXTRACT(R_TLB_SELECT, index, select); #endif miss = IO_EXTRACT(R_MMU_CAUSE, miss_excp, cause); @@ -84,12 +84,13 @@ handle_mmu_bus_fault(struct pt_regs *regs) local_irq_disable(); pmd = (pmd_t *)(pgd + pgd_index(address)); if (pmd_none(*pmd)) - return; + goto exit; pte = *pte_offset_kernel(pmd, address); if (!pte_present(pte)) - return; + goto exit; *R_TLB_SELECT = select; *R_TLB_HI = cause; *R_TLB_LO = pte_val(pte); +exit: local_irq_restore(flags); } diff --git a/arch/cris/arch-v10/mm/tlb.c b/arch/cris/arch-v10/mm/tlb.c index 7d9fec88dee5..6baf5bd209e7 100644 --- a/arch/cris/arch-v10/mm/tlb.c +++ b/arch/cris/arch-v10/mm/tlb.c @@ -4,8 +4,8 @@ * Low level TLB handling * * - * Copyright (C) 2000-2002 Axis Communications AB - * + * Copyright (C) 2000-2007 Axis Communications AB + * * Authors: Bjorn Wesen (bjornw@axis.com) * */ @@ -39,7 +39,7 @@ flush_tlb_all(void) unsigned long flags; /* the vpn of i & 0xf is so we dont write similar TLB entries - * in the same 4-way entry group. details.. + * in the same 4-way entry group. details... */ local_irq_save(flags); @@ -47,7 +47,7 @@ flush_tlb_all(void) *R_TLB_SELECT = ( IO_FIELD(R_TLB_SELECT, index, i) ); *R_TLB_HI = ( IO_FIELD(R_TLB_HI, page_id, INVALID_PAGEID ) | IO_FIELD(R_TLB_HI, vpn, i & 0xf ) ); - + *R_TLB_LO = ( IO_STATE(R_TLB_LO, global,no ) | IO_STATE(R_TLB_LO, valid, no ) | IO_STATE(R_TLB_LO, kernel,no ) | @@ -71,10 +71,10 @@ flush_tlb_mm(struct mm_struct *mm) if(page_id == NO_CONTEXT) return; - + /* mark the TLB entries that match the page_id as invalid. * here we could also check the _PAGE_GLOBAL bit and NOT flush - * global pages. is it worth the extra I/O ? + * global pages. is it worth the extra I/O ? */ local_irq_save(flags); @@ -83,7 +83,7 @@ flush_tlb_mm(struct mm_struct *mm) if (IO_EXTRACT(R_TLB_HI, page_id, *R_TLB_HI) == page_id) { *R_TLB_HI = ( IO_FIELD(R_TLB_HI, page_id, INVALID_PAGEID ) | IO_FIELD(R_TLB_HI, vpn, i & 0xf ) ); - + *R_TLB_LO = ( IO_STATE(R_TLB_LO, global,no ) | IO_STATE(R_TLB_LO, valid, no ) | IO_STATE(R_TLB_LO, kernel,no ) | @@ -96,9 +96,7 @@ flush_tlb_mm(struct mm_struct *mm) /* invalidate a single page */ -void -flush_tlb_page(struct vm_area_struct *vma, - unsigned long addr) +void flush_tlb_page(struct vm_area_struct *vma, unsigned long addr) { struct mm_struct *mm = vma->vm_mm; int page_id = mm->context.page_id; @@ -113,7 +111,7 @@ flush_tlb_page(struct vm_area_struct *vma, addr &= PAGE_MASK; /* perhaps not necessary */ /* invalidate those TLB entries that match both the mm context - * and the virtual address requested + * and the virtual address requested */ local_irq_save(flags); @@ -125,7 +123,7 @@ flush_tlb_page(struct vm_area_struct *vma, (tlb_hi & PAGE_MASK) == addr) { *R_TLB_HI = IO_FIELD(R_TLB_HI, page_id, INVALID_PAGEID ) | addr; /* same addr as before works. */ - + *R_TLB_LO = ( IO_STATE(R_TLB_LO, global,no ) | IO_STATE(R_TLB_LO, valid, no ) | IO_STATE(R_TLB_LO, kernel,no ) | @@ -144,7 +142,7 @@ dump_tlb_all(void) { int i; unsigned long flags; - + printk("TLB dump. LO is: pfn | reserved | global | valid | kernel | we |\n"); local_save_flags(flags); @@ -172,27 +170,29 @@ init_new_context(struct task_struct *tsk, struct mm_struct *mm) /* called in schedule() just before actually doing the switch_to */ -void -switch_mm(struct mm_struct *prev, struct mm_struct *next, - struct task_struct *tsk) +void switch_mm(struct mm_struct *prev, struct mm_struct *next, + struct task_struct *tsk) { - /* make sure we have a context */ + if (prev != next) { + /* make sure we have a context */ + get_mmu_context(next); - get_mmu_context(next); + /* remember the pgd for the fault handlers + * this is similar to the pgd register in some other CPU's. + * we need our own copy of it because current and active_mm + * might be invalid at points where we still need to derefer + * the pgd. + */ - /* remember the pgd for the fault handlers - * this is similar to the pgd register in some other CPU's. - * we need our own copy of it because current and active_mm - * might be invalid at points where we still need to derefer - * the pgd. - */ + per_cpu(current_pgd, smp_processor_id()) = next->pgd; - per_cpu(current_pgd, smp_processor_id()) = next->pgd; + /* switch context in the MMU */ - /* switch context in the MMU */ - - D(printk("switching mmu_context to %d (%p)\n", next->context, next)); + D(printk(KERN_DEBUG "switching mmu_context to %d (%p)\n", + next->context, next)); - *R_MMU_CONTEXT = IO_FIELD(R_MMU_CONTEXT, page_id, next->context.page_id); + *R_MMU_CONTEXT = IO_FIELD(R_MMU_CONTEXT, + page_id, next->context.page_id); + } } |
