diff options
Diffstat (limited to 'Documentation')
9 files changed, 101 insertions, 36 deletions
diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt index 947863acc2d4..7b94c88cf2ee 100644 --- a/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt +++ b/Documentation/devicetree/bindings/iommu/arm,smmu-v3.txt @@ -1,6 +1,6 @@ * ARM SMMUv3 Architecture Implementation -The SMMUv3 architecture is a significant deparature from previous +The SMMUv3 architecture is a significant departure from previous revisions, replacing the MMIO register interface with in-memory command and event queues and adding support for the ATS and PRI components of the PCIe specification. diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt index cd1b1cd7b5c4..53c20cae309f 100644 --- a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt +++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt @@ -1,7 +1,9 @@ * Mediatek IOMMU Architecture Implementation - Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U) which -uses the ARM Short-Descriptor translation table format for address translation. + Some Mediatek SOCs contain a Multimedia Memory Management Unit (M4U), and +this M4U have two generations of HW architecture. Generation one uses flat +pagetable, and only supports 4K size page mapping. Generation two uses the +ARM Short-Descriptor translation table format for address translation. About the M4U Hardware Block Diagram, please check below: @@ -36,7 +38,9 @@ in each larb. Take a example, There are many ports like MC, PP, VLD in the video decode local arbiter, all these ports are according to the video HW. Required properties: -- compatible : must be "mediatek,mt8173-m4u". +- compatible : must be one of the following string: + "mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW. + "mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW. - reg : m4u register base and size. - interrupts : the interrupt of m4u. - clocks : must contain one entry for each clock-names. @@ -46,7 +50,8 @@ Required properties: according to the local arbiter index, like larb0, larb1, larb2... - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW. Specifies the mtk_m4u_id as defined in - dt-binding/memory/mt8173-larb-port.h. + dt-binding/memory/mt2701-larb-port.h for mt2701 and + dt-binding/memory/mt8173-larb-port.h for mt8173 Example: iommu: iommu@10205000 { diff --git a/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt b/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt new file mode 100644 index 000000000000..20236385f26e --- /dev/null +++ b/Documentation/devicetree/bindings/iommu/msm,iommu-v0.txt @@ -0,0 +1,64 @@ +* QCOM IOMMU + +The MSM IOMMU is an implementation compatible with the ARM VMSA short +descriptor page tables. It provides address translation for bus masters outside +of the CPU, each connected to the IOMMU through a port called micro-TLB. + +Required Properties: + + - compatible: Must contain "qcom,apq8064-iommu". + - reg: Base address and size of the IOMMU registers. + - interrupts: Specifiers for the MMU fault interrupts. For instances that + support secure mode two interrupts must be specified, for non-secure and + secure mode, in that order. For instances that don't support secure mode a + single interrupt must be specified. + - #iommu-cells: The number of cells needed to specify the stream id. This + is always 1. + - qcom,ncb: The total number of context banks in the IOMMU. + - clocks : List of clocks to be used during SMMU register access. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + for information about the format. For each clock specified + here, there must be a corresponding entry in clock-names + (see below). + + - clock-names : List of clock names corresponding to the clocks specified in + the "clocks" property (above). + Should be "smmu_pclk" for specifying the interface clock + required for iommu's register accesses. + Should be "smmu_clk" for specifying the functional clock + required by iommu for bus accesses. + +Each bus master connected to an IOMMU must reference the IOMMU in its device +node with the following property: + + - iommus: A reference to the IOMMU in multiple cells. The first cell is a + phandle to the IOMMU and the second cell is the stream id. + A single master device can be connected to more than one iommu + and multiple contexts in each of the iommu. So multiple entries + are required to list all the iommus and the stream ids that the + master is connected to. + +Example: mdp iommu and its bus master + + mdp_port0: iommu@7500000 { + compatible = "qcom,apq8064-iommu"; + #iommu-cells = <1>; + clock-names = + "smmu_pclk", + "smmu_clk"; + clocks = + <&mmcc SMMU_AHB_CLK>, + <&mmcc MDP_AXI_CLK>; + reg = <0x07500000 0x100000>; + interrupts = + <GIC_SPI 63 0>, + <GIC_SPI 64 0>; + qcom,ncb = <2>; + }; + + mdp: qcom,mdp@5100000 { + compatible = "qcom,mdp"; + ... + iommus = <&mdp_port0 0 + &mdp_port0 2>; + }; diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt index 06a83ceebba7..aa614b2d7cab 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt @@ -2,16 +2,31 @@ SMI (Smart Multimedia Interface) Common The hardware block diagram please check bindings/iommu/mediatek,iommu.txt +Mediatek SMI have two generations of HW architecture, mt8173 uses the second +generation of SMI HW while mt2701 uses the first generation HW of SMI. + +There's slight differences between the two SMI, for generation 2, the +register which control the iommu port is at each larb's register base. But +for generation 1, the register is at smi ao base(smi always on register +base). Besides that, the smi async clock should be prepared and enabled for +SMI generation 1 to transform the smi clock into emi clock domain, but that is +not needed for SMI generation 2. + Required properties: -- compatible : must be "mediatek,mt8173-smi-common" +- compatible : must be one of : + "mediatek,mt2701-smi-common" + "mediatek,mt8173-smi-common" - reg : the register and size of the SMI block. - power-domains : a phandle to the power domain of this local arbiter. - clocks : Must contain an entry for each entry in clock-names. -- clock-names : must contain 2 entries, as follows: +- clock-names : must contain 3 entries for generation 1 smi HW and 2 entries + for generation 2 smi HW as follows: - "apb" : Advanced Peripheral Bus clock, It's the clock for setting the register. - "smi" : It's the clock for transfer data and command. - They may be the same if both source clocks are the same. + They may be the same if both source clocks are the same. + - "async" : asynchronous clock, it help transform the smi clock into the emi + clock domain, this clock is only needed by generation 1 smi HW. Example: smi_common: smi@14022000 { diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt index 55ff3b7e0bb9..21277a56e94c 100644 --- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt +++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt @@ -3,7 +3,9 @@ SMI (Smart Multimedia Interface) Local Arbiter The hardware block diagram please check bindings/iommu/mediatek,iommu.txt Required properties: -- compatible : must be "mediatek,mt8173-smi-larb" +- compatible : must be one of : + "mediatek,mt8173-smi-larb" + "mediatek,mt2701-smi-larb" - reg : the register and size of this local arbiter. - mediatek,smi : a phandle to the smi_common node. - power-domains : a phandle to the power domain of this local arbiter. diff --git a/Documentation/gdb-kernel-debugging.txt b/Documentation/gdb-kernel-debugging.txt index 4ab7d43d0754..7050ce8794b9 100644 --- a/Documentation/gdb-kernel-debugging.txt +++ b/Documentation/gdb-kernel-debugging.txt @@ -139,27 +139,6 @@ Examples of using the Linux-provided gdb helpers start_comm = "swapper/2\000\000\000\000\000\000" } - o Dig into a radix tree data structure, such as the IRQ descriptors: - (gdb) print (struct irq_desc)$lx_radix_tree_lookup(irq_desc_tree, 18) - $6 = { - irq_common_data = { - state_use_accessors = 67584, - handler_data = 0x0 <__vectors_start>, - msi_desc = 0x0 <__vectors_start>, - affinity = {{ - bits = {65535} - }} - }, - irq_data = { - mask = 0, - irq = 18, - hwirq = 27, - common = 0xee803d80, - chip = 0xc0eb0854 <gic_data>, - domain = 0xee808000, - parent_data = 0x0 <__vectors_start>, - chip_data = 0xc0eb0854 <gic_data> - } <... trimmed ...> List of commands and functions ------------------------------ diff --git a/Documentation/x86/intel_mpx.txt b/Documentation/x86/intel_mpx.txt index 1a5a12184a35..85d0549ad846 100644 --- a/Documentation/x86/intel_mpx.txt +++ b/Documentation/x86/intel_mpx.txt @@ -45,7 +45,7 @@ is how we expect the compiler, application and kernel to work together. MPX-instrumented. 3) The kernel detects that the CPU has MPX, allows the new prctl() to succeed, and notes the location of the bounds directory. Userspace is - expected to keep the bounds directory at that locationWe note it + expected to keep the bounds directory at that location. We note it instead of reading it each time because the 'xsave' operation needed to access the bounds directory register is an expensive operation. 4) If the application needs to spill bounds out of the 4 registers, it @@ -167,7 +167,7 @@ If a #BR is generated due to a bounds violation caused by MPX. We need to decode MPX instructions to get violation address and set this address into extended struct siginfo. -The _sigfault feild of struct siginfo is extended as follow: +The _sigfault field of struct siginfo is extended as follow: 87 /* SIGILL, SIGFPE, SIGSEGV, SIGBUS */ 88 struct { @@ -240,5 +240,5 @@ them at the same bounds table. This is allowed architecturally. See more information "Intel(R) Architecture Instruction Set Extensions Programming Reference" (9.3.4). -However, if users did this, the kernel might be fooled in to unmaping an +However, if users did this, the kernel might be fooled in to unmapping an in-use bounds table since it does not recognize sharing. diff --git a/Documentation/x86/tlb.txt b/Documentation/x86/tlb.txt index 39d172326703..6a0607b99ed8 100644 --- a/Documentation/x86/tlb.txt +++ b/Documentation/x86/tlb.txt @@ -5,7 +5,7 @@ memory, it has two choices: from areas other than the one we are trying to flush will be destroyed and must be refilled later, at some cost. 2. Use the invlpg instruction to invalidate a single page at a - time. This could potentialy cost many more instructions, but + time. This could potentially cost many more instructions, but it is a much more precise operation, causing no collateral damage to other TLB entries. @@ -19,7 +19,7 @@ Which method to do depends on a few things: work. 3. The size of the TLB. The larger the TLB, the more collateral damage we do with a full flush. So, the larger the TLB, the - more attrative an individual flush looks. Data and + more attractive an individual flush looks. Data and instructions have separate TLBs, as do different page sizes. 4. The microarchitecture. The TLB has become a multi-level cache on modern CPUs, and the global flushes have become more diff --git a/Documentation/x86/x86_64/machinecheck b/Documentation/x86/x86_64/machinecheck index b1fb30273286..d0648a74fceb 100644 --- a/Documentation/x86/x86_64/machinecheck +++ b/Documentation/x86/x86_64/machinecheck @@ -36,7 +36,7 @@ between all CPUs. check_interval How often to poll for corrected machine check errors, in seconds - (Note output is hexademical). Default 5 minutes. When the poller + (Note output is hexadecimal). Default 5 minutes. When the poller finds MCEs it triggers an exponential speedup (poll more often) on the polling interval. When the poller stops finding MCEs, it triggers an exponential backoff (poll less often) on the polling |
