diff options
Diffstat (limited to 'Documentation')
4 files changed, 87 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt index e2d501d20c9a..1eceefb20f01 100644 --- a/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt +++ b/Documentation/devicetree/bindings/bus/brcm,gisb-arb.txt @@ -2,7 +2,11 @@ Broadcom GISB bus Arbiter controller Required properties: -- compatible: should be "brcm,gisb-arb" +- compatible: + "brcm,gisb-arb" or "brcm,bcm7445-gisb-arb" for 28nm chips + "brcm,bcm7435-gisb-arb" for newer 40nm chips + "brcm,bcm7400-gisb-arb" for older 40nm chips and all 65nm chips + "brcm,bcm7038-gisb-arb" for 130nm chips - reg: specifies the base physical address and size of the registers - interrupt-parent: specifies the phandle to the parent interrupt controller this arbiter gets interrupt line from diff --git a/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt new file mode 100644 index 000000000000..54ae9f747e45 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt @@ -0,0 +1,42 @@ +STMicroelectronics STi family Sysconfig Picophy SoftReset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip PicoPHY USB2 phy(s) using "softreset" control bits found in +the STi family SoC system configuration registers. + +The actual action taken when softreset is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to Documentation/devicetree/bindings/reset/reset.txt +for common reset controller binding usage. + +Required properties: +- compatible: Should be "st,stih407-picophyreset" +- #reset-cells: 1, see below + +Example: + + picophyreset: picophyreset-controller { + compatible = "st,stih407-picophyreset"; + #reset-cells = <1>; + }; + +Specifying picophyreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the picophyreset device node and an +index specifying which channel to use, as described in +Documentation/devicetree/bindings/reset/reset.txt. + +Example: + + usb2_picophy0: usbpicophy@0 { + resets = <&picophyreset STIH407_PICOPHY0_RESET>; + }; + +Macro definitions for the supported reset channels can be found in: +include/dt-bindings/reset-controller/stih407-resets.h diff --git a/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt b/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt new file mode 100644 index 000000000000..6ae79d1843f3 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/atmel,at91sam9-rtc.txt @@ -0,0 +1,23 @@ +Atmel AT91SAM9260 Real Time Timer + +Required properties: +- compatible: should be: "atmel,at91sam9260-rtt" +- reg: should encode the memory region of the RTT controller +- interrupts: rtt alarm/event interrupt +- clocks: should contain the 32 KHz slow clk that will drive the RTT block. +- atmel,rtt-rtc-time-reg: should encode the GPBR register used to store + the time base when the RTT is used as an RTC. + The first cell should point to the GPBR node and the second one + encode the offset within the GPBR block (or in other words, the + GPBR register used to store the time base). + + +Example: + +rtt@fffffd20 { + compatible = "atmel,at91sam9260-rtt"; + reg = <0xfffffd20 0x10>; + interrupts = <1 4 7>; + clocks = <&clk32k>; + atmel,rtt-rtc-time-reg = <&gpbr 0x0>; +}; diff --git a/Documentation/devicetree/bindings/w1/omap-hdq.txt b/Documentation/devicetree/bindings/w1/omap-hdq.txt new file mode 100644 index 000000000000..fef794741bd1 --- /dev/null +++ b/Documentation/devicetree/bindings/w1/omap-hdq.txt @@ -0,0 +1,17 @@ +* OMAP HDQ One wire bus master controller + +Required properties: +- compatible : should be "ti,omap3-1w" +- reg : Address and length of the register set for the device +- interrupts : interrupt line. +- ti,hwmods : "hdq1w" + +Example: + +- From omap3.dtsi + hdqw1w: 1w@480b2000 { + compatible = "ti,omap3-1w"; + reg = <0x480b2000 0x1000>; + interrupts = <58>; + ti,hwmods = "hdq1w"; + }; |
