diff options
Diffstat (limited to 'Documentation/devicetree')
49 files changed, 1906 insertions, 599 deletions
diff --git a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt index 6b458bb2440d..f2aab3dc2b52 100644 --- a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt +++ b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt @@ -66,16 +66,3 @@ sha@f8034000 { dmas = <&dma1 2 17>; dma-names = "tx"; }; - -* Eliptic Curve Cryptography (I2C) - -Required properties: -- compatible : must be "atmel,atecc508a". -- reg: I2C bus address of the device. -- clock-frequency: must be present in the i2c controller node. - -Example: -atecc508a@c0 { - compatible = "atmel,atecc508a"; - reg = <0xC0>; -}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-davinci.txt b/Documentation/devicetree/bindings/gpio/gpio-davinci.txt index 553b92a7e87b..bc6b4b62df83 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-davinci.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-davinci.txt @@ -5,6 +5,7 @@ Required Properties: "ti,keystone-gpio": for Keystone 2 66AK2H/K, 66AK2L, 66AK2E SoCs "ti,k2g-gpio", "ti,keystone-gpio": for 66AK2G + "ti,am654-gpio", "ti,keystone-gpio": for TI K3 AM654 - reg: Physical base address of the controller and the size of memory mapped registers. @@ -145,3 +146,20 @@ gpio0: gpio@260bf00 { ti,ngpio = <32>; ti,davinci-gpio-unbanked = <32>; }; + +Example for K3 AM654: + +wkup_gpio0: wkup_gpio0@42110000 { + compatible = "ti,am654-gpio", "ti,keystone-gpio"; + reg = <0x42110000 0x100>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&intr_wkup_gpio>; + interrupts = <59 128>, <59 129>, <59 130>, <59 131>; + interrupt-controller; + #interrupt-cells = <2>; + ti,ngpio = <56>; + ti,davinci-gpio-unbanked = <0>; + clocks = <&k3_clks 59 0>; + clock-names = "gpio"; +}; diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt b/Documentation/devicetree/bindings/gpio/pl061-gpio.txt deleted file mode 100644 index 89058d375b7c..000000000000 --- a/Documentation/devicetree/bindings/gpio/pl061-gpio.txt +++ /dev/null @@ -1,10 +0,0 @@ -ARM PL061 GPIO controller - -Required properties: -- compatible : "arm,pl061", "arm,primecell" -- #gpio-cells : Should be two. The first cell is the pin number and the - second cell is used to specify optional parameters: - - bit 0 specifies polarity (0 for normal, 1 for inverted) -- gpio-controller : Marks the device node as a GPIO controller. -- interrupts : Interrupt mapping for GPIO IRQ. -- gpio-ranges : Interaction with the PINCTRL subsystem. diff --git a/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml b/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml new file mode 100644 index 000000000000..313b17229247 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/pl061-gpio.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/gpio/pl061-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM PL061 GPIO controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Rob Herring <robh@kernel.org> + +# We need a select here so we don't match all nodes with 'arm,primecell' +select: + properties: + compatible: + contains: + const: arm,pl061 + required: + - compatible + +properties: + $nodename: + pattern: "^gpio@[0-9a-f]+$" + + compatible: + items: + - const: arm,pl061 + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + oneOf: + - maxItems: 1 + - maxItems: 8 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + + clocks: + maxItems: 1 + + clock-names: true + + "#gpio-cells": + const: 2 + + gpio-controller: true + + gpio-ranges: + maxItems: 8 + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + - clocks + - "#gpio-cells" + - gpio-controller + +additionalProperties: false + +... diff --git a/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt b/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt index 69da2115abdc..1cf6182f888c 100644 --- a/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt +++ b/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt @@ -38,6 +38,6 @@ Example: nunchuk: nunchuk@52 { compatible = "nintendo,nunchuk"; - reg = <0x52 0x80000010 0>; + reg = <0x52 0x0 0x10>; }; }; diff --git a/Documentation/devicetree/bindings/i3c/i3c.txt b/Documentation/devicetree/bindings/i3c/i3c.txt index ab729a0a86ae..4ffe059f0fec 100644 --- a/Documentation/devicetree/bindings/i3c/i3c.txt +++ b/Documentation/devicetree/bindings/i3c/i3c.txt @@ -39,7 +39,9 @@ valid here, but several new properties have been added. New constraint on existing properties: -------------------------------------- - reg: contains 3 cells - + first cell : still encoding the I2C address + + first cell : still encoding the I2C address. 10 bit addressing is not + supported. Devices with 10 bit address can't be properly passed through + DEFSLVS command. + second cell: shall be 0 diff --git a/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt b/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt new file mode 100644 index 000000000000..4e82fd575cec --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt @@ -0,0 +1,29 @@ +Amazon's Annapurna Labs Fabric Interrupt Controller + +Required properties: + +- compatible: should be "amazon,al-fic" +- reg: physical base address and size of the registers +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: must be 2. + First cell defines the index of the interrupt within the controller. + Second cell is used to specify the trigger type and must be one of the + following: + - bits[3:0] trigger type and level flags + 1 = low-to-high edge triggered + 4 = active high level-sensitive +- interrupt-parent: specifies the parent interrupt controller. +- interrupts: describes which input line in the interrupt parent, this + fic's output is connected to. This field property depends on the parent's + binding + +Example: + +amazon_fic: interrupt-controller@0xfd8a8500 { + compatible = "amazon,al-fic"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x0 0xfd8a8500 0x0 0x1000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 0x0 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt index 1502a51548bb..7d531d5fff29 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -15,6 +15,7 @@ Required properties: "amlogic,meson-gxbb-gpio-intc" for GXBB SoCs (S905) or "amlogic,meson-gxl-gpio-intc" for GXL SoCs (S905X, S912) "amlogic,meson-axg-gpio-intc" for AXG SoCs (A113D, A113X) + "amlogic,meson-g12a-gpio-intc" for G12A SoCs (S905D2, S905X2, S905Y2) - reg : Specifies base physical address and size of the registers. - interrupt-controller : Identifies the node as an interrupt controller. - #interrupt-cells : Specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt index ab921f1698fb..e13405355166 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt @@ -6,11 +6,16 @@ C-SKY Multi-processors Interrupt Controller is designed for ck807/ck810/ck860 SMP soc, and it also could be used in non-SMP system. Interrupt number definition: - 0-15 : software irq, and we use 15 as our IPI_IRQ. 16-31 : private irq, and we use 16 as the co-processor timer. 31-1024: common irq for soc ip. +Interrupt triger mode: (Defined in dt-bindings/interrupt-controller/irq.h) + IRQ_TYPE_LEVEL_HIGH (default) + IRQ_TYPE_LEVEL_LOW + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + ============================= intc node bindings definition ============================= @@ -26,15 +31,22 @@ intc node bindings definition - #interrupt-cells Usage: required Value type: <u32> - Definition: must be <1> + Definition: <2> - interrupt-controller: Usage: required -Examples: +Examples: ("interrupts = <irq_num IRQ_TYPE_XXX>") --------- +#include <dt-bindings/interrupt-controller/irq.h> intc: interrupt-controller { compatible = "csky,mpintc"; - #interrupt-cells = <1>; + #interrupt-cells = <2>; interrupt-controller; }; + + device: device-example { + ... + interrupts = <34 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&intc>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt new file mode 100644 index 000000000000..727b7e4cd6e0 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt @@ -0,0 +1,43 @@ +DT bindings for the Renesas RZ/A1 Interrupt Controller + +The RZ/A1 Interrupt Controller is a front-end for the GIC found on Renesas +RZ/A1 and RZ/A2 SoCs: + - IRQ sense select for 8 external interrupts, 1:1-mapped to 8 GIC SPI + interrupts, + - NMI edge select. + +Required properties: + - compatible: Must be "renesas,<soctype>-irqc", and "renesas,rza1-irqc" as + fallback. + Examples with soctypes are: + - "renesas,r7s72100-irqc" (RZ/A1H) + - "renesas,r7s9210-irqc" (RZ/A2M) + - #interrupt-cells: Must be 2 (an interrupt index and flags, as defined + in interrupts.txt in this directory) + - #address-cells: Must be zero + - interrupt-controller: Marks the device as an interrupt controller + - reg: Base address and length of the memory resource used by the interrupt + controller + - interrupt-map: Specifies the mapping from external interrupts to GIC + interrupts + - interrupt-map-mask: Must be <7 0> + +Example: + + irqc: interrupt-controller@fcfef800 { + compatible = "renesas,r7s72100-irqc", "renesas,rza1-irqc"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0xfcfef800 0x6>; + interrupt-map = + <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <7 0>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-lm36274.txt b/Documentation/devicetree/bindings/leds/leds-lm36274.txt new file mode 100644 index 000000000000..39c230d59a4d --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm36274.txt @@ -0,0 +1,85 @@ +* Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias + +The LM36274 is an integrated four-channel WLED driver and LCD bias supply. +The backlight boost provides the power to bias four parallel LED strings with +up to 29V total output voltage. The 11-bit LED current is programmable via +the I2C bus and/or controlled via a logic level PWM input from 60 uA to 30 mA. + +Parent device properties are documented in +Documentation/devicetree/bindings/mfd/ti-lmu.txt + +Regulator properties are documented in +Documentation/devicetree/bindings/regulator/lm363x-regulator.txt + +Required backlight properties: + - compatible: + "ti,lm36274-backlight" + - reg : 0 + - #address-cells : 1 + - #size-cells : 0 + - led-sources : Indicates which LED strings will be enabled. + Values from 0-3, sources is 0 based so strings will be + source value + 1. + +Optional backlight properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is +controlled by control bank B. + +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; + + enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; + + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + }; + + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; + }; +}; + +For more product information please see the link below: +http://www.ti.com/lit/ds/symlink/lm36274.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-lm3697.txt b/Documentation/devicetree/bindings/leds/leds-lm3697.txt new file mode 100644 index 000000000000..63992d732959 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm3697.txt @@ -0,0 +1,73 @@ +* Texas Instruments - LM3697 Highly Efficient White LED Driver + +The LM3697 11-bit LED driver provides high- +performance backlight dimming for 1, 2, or 3 series +LED strings while delivering up to 90% efficiency. + +This device is suitable for display and keypad lighting + +Required properties: + - compatible: + "ti,lm3697" + - reg : I2C slave address + - #address-cells : 1 + - #size-cells : 0 + +Optional properties: + - enable-gpios : GPIO pin to enable/disable the device + - vled-supply : LED supply + +Required child properties: + - reg : 0 - LED is Controlled by bank A + 1 - LED is Controlled by bank B + - led-sources : Indicates which HVLED string is associated to which + control bank. This is a zero based property so + HVLED1 = 0, HVLED2 = 1, HVLED3 = 2. + Additional information is contained + in Documentation/devicetree/bindings/leds/common.txt + +Optional child properties: + - ti,brightness-resolution - see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - ramp-up-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - ramp-down-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is +controlled by control bank B. + +led-controller@36 { + compatible = "ti,lm3697"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x36>; + + enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + vled-supply = <&vbatt>; + + led@0 { + reg = <0>; + led-sources = <0 2>; + ti,brightness-resolution = <2047>; + ramp-up-us = <5000>; + ramp-down-us = <1000>; + label = "white:first_backlight_cluster"; + linux,default-trigger = "backlight"; + }; + + led@1 { + reg = <1>; + led-sources = <1>; + ti,brightness-resolution = <255>; + ramp-up-us = <500>; + ramp-down-us = <1000>; + label = "white:second_backlight_cluster"; + linux,default-trigger = "backlight"; + }; +} + +For more product information please see the link below: +http://www.ti.com/lit/ds/symlink/lm3697.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-spi-byte.txt b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt new file mode 100644 index 000000000000..28b6b2d9091e --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt @@ -0,0 +1,44 @@ +* Single Byte SPI LED Device Driver. + +The driver can be used for controllers with a very simple SPI protocol: +- one LED is controlled by a single byte on MOSI +- the value of the byte gives the brightness between two values (lowest to + highest) +- no return value is necessary (no MISO signal) + +The value for lowest and highest brightness is dependent on the device and +therefore on the compatible string. + +Depending on the compatible string some special functions (like hardware +accelerated blinking) might can be supported too. + +The driver currently only supports one LED. The properties of the LED are +configured in a sub-node in the device node. + +Required properties: +- compatible: should be one of + * "ubnt,acb-spi-led" microcontroller (SONiX 8F26E611LA) based device + used for example in Ubiquiti airCube ISP + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. + +LED sub-node properties: +- label: + see Documentation/devicetree/bindings/leds/common.txt +- default-state: + see Documentation/devicetree/bindings/leds/common.txt + Only "on" and "off" are supported. + +Example: + +led-controller@0 { + compatible = "ubnt,acb-spi-led"; + reg = <0>; + spi-max-frequency = <100000>; + + led { + label = "white:status"; + default-state = "on"; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/atmel-usart.txt b/Documentation/devicetree/bindings/mfd/atmel-usart.txt index 7f0cd72f47d2..699fd3c9ace8 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-usart.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-usart.txt @@ -17,17 +17,24 @@ Required properties for USART in SPI mode: - cs-gpios: chipselects (internal cs not supported) - atmel,usart-mode : Must be <AT91_USART_MODE_SPI> (found in dt-bindings/mfd/at91-usart.h) +Optional properties in serial and SPI mode: +- dma bindings for dma transfer: + - dmas: DMA specifier, consisting of a phandle to DMA controller node, + memory peripheral interface and USART DMA channel ID, FIFO configuration. + The order of DMA channels is fixed. The first DMA channel must be TX + associated channel and the second one must be RX associated channel. + Refer to dma.txt and atmel-dma.txt for details. + - dma-names: "tx" for TX channel. + "rx" for RX channel. + The order of dma-names is also fixed. The first name must be "tx" + and the second one must be "rx" as in the examples below. + Optional properties in serial mode: - atmel,use-dma-rx: use of PDC or DMA for receiving data - atmel,use-dma-tx: use of PDC or DMA for transmitting data - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD line respectively. It will use specified PIO instead of the peripheral function pin for the USART feature. If unsure, don't specify this property. -- add dma bindings for dma transfer: - - dmas: DMA specifier, consisting of a phandle to DMA controller node, - memory peripheral interface and USART DMA channel ID, FIFO configuration. - Refer to dma.txt and atmel-dma.txt for details. - - dma-names: "rx" for RX channel, "tx" for TX channel. - atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO capable USARTs. - rs485-rts-delay, rs485-rx-during-tx, linux,rs485-enabled-at-boot-time: see rs485.txt @@ -81,5 +88,8 @@ Example: interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>; clocks = <&usart0_clk>; clock-names = "usart"; + dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>, + <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>; + dma-names = "tx", "rx"; cs-gpios = <&pioB 3 0>; }; diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt index 86ca786d54fc..2296b8f24de4 100644 --- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt @@ -8,7 +8,7 @@ TI LMU driver supports lighting devices below. LM3632 Backlight and regulator LM3633 Backlight, LED and fault monitor LM3695 Backlight - LM3697 Backlight and fault monitor + LM36274 Backlight and regulator Required properties: - compatible: Should be one of: @@ -16,15 +16,32 @@ Required properties: "ti,lm3632" "ti,lm3633" "ti,lm3695" - "ti,lm3697" + "ti,lm36274" - reg: I2C slave address. 0x11 for LM3632 0x29 for LM3631 - 0x36 for LM3633, LM3697 + 0x36 for LM3633 0x63 for LM3695 + 0x11 for LM36274 -Optional property: +Optional properties: - enable-gpios: A GPIO specifier for hardware enable pin. + - ramp-up-us: Current ramping from one brightness level to + the a higher brightness level. + Range from 2048 us - 117.44 s + - ramp-down-us: Current ramping from one brightness level to + the a lower brightness level. + Range from 2048 us - 117.44 s + - ti,brightness-resolution - This determines whether to use 8 bit brightness + mode or 11 bit brightness mode. If this value is + not set the device is defaulted to the preferred + 8bit brightness mode per 7.3.4.1 of the data + sheet. This setting can either be in the parent + node or as part of the LED child nodes. This + is determined by the part itself if the strings + have a common brightness register or individual + brightness registers. + The values are 255 (8bit) or 2047 (11bit). Required node: - backlight: All LMU devices have backlight child nodes. @@ -35,14 +52,15 @@ Optional nodes: Required properties: - compatible: Should be one of: "ti,lm3633-fault-monitor" - "ti,lm3697-fault-monitor" - leds: LED properties for LM3633. Please refer to [2]. + LED properties for LM36274. Please refer to [4]. - regulators: Regulator properties for LM3631 and LM3632. Please refer to [3]. [1] ../leds/backlight/ti-lmu-backlight.txt [2] ../leds/leds-lm3633.txt [3] ../regulator/lm363x-regulator.txt +[4] ../leds/leds-lm36274.txt lm3631@29 { compatible = "ti,lm3631"; @@ -90,7 +108,7 @@ lm3631@29 { lcd_bl { led-sources = <0 1>; - ramp-up-msec = <300>; + ramp-up-us = <300000>; }; }; }; @@ -152,15 +170,15 @@ lm3633@36 { main { label = "main_lcd"; led-sources = <1 2>; - ramp-up-msec = <500>; - ramp-down-msec = <500>; + ramp-up-us = <500000>; + ramp-down-us = <500000>; }; front { label = "front_lcd"; led-sources = <0>; - ramp-up-msec = <1000>; - ramp-down-msec = <0>; + ramp-up-us = <1000000>; + ramp-down-us = <0>; }; }; @@ -201,23 +219,51 @@ lm3695@63 { }; }; -lm3697@36 { - compatible = "ti,lm3697"; - reg = <0x36>; +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; - backlight { - compatible = "ti,lm3697-backlight"; + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; - lcd { - led-sources = <0 1 2>; - ramp-up-msec = <200>; - ramp-down-msec = <200>; + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; }; }; - fault-monitor { - compatible = "ti,lm3697-fault-monitor"; + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; }; }; diff --git a/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt index 188c8bd4eb67..5a0111d4de58 100644 --- a/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt +++ b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be one of the following: - "microchip,mcp2510" for MCP2510. - "microchip,mcp2515" for MCP2515. + - "microchip,mcp25625" for MCP25625. - reg: SPI chip select. - clocks: The clock feeding the CAN controller. - interrupts: Should contain IRQ line for the CAN controller. diff --git a/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt b/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt new file mode 100644 index 000000000000..d77e3f26f9e6 --- /dev/null +++ b/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt @@ -0,0 +1,21 @@ +* Freescale(NXP) IMX8 DDR performance monitor + +Required properties: + +- compatible: should be one of: + "fsl,imx8-ddr-pmu" + "fsl,imx8m-ddr-pmu" + +- reg: physical address and size + +- interrupts: single interrupt + generated by the control block + +Example: + + ddr-pmu@5c020000 { + compatible = "fsl,imx8-ddr-pmu"; + reg = <0x5c020000 0x10000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt index 7d9d3f90641b..493bec80d59b 100644 --- a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt @@ -2,10 +2,7 @@ Ingenic JZ47xx PWM Controller ============================= Required properties: -- compatible: One of: - * "ingenic,jz4740-pwm" - * "ingenic,jz4770-pwm" - * "ingenic,jz4780-pwm" +- compatible: Should be "ingenic,jz4740-pwm" - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. - clocks : phandle to the external clock. diff --git a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt new file mode 100644 index 000000000000..36447e3c9378 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt @@ -0,0 +1,33 @@ +SiFive PWM controller + +Unlike most other PWM controllers, the SiFive PWM controller currently only +supports one period for all channels in the PWM. All PWMs need to run at +the same period. The period also has significant restrictions on the values +it can achieve, which the driver rounds to the nearest achievable period. +PWM RTL that corresponds to the IP block version numbers can be found +here: + +https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/pwm + +Required properties: +- compatible: Should be "sifive,<chip>-pwm" and "sifive,pwm<version>". + Supported compatible strings are: "sifive,fu540-c000-pwm" for the SiFive + PWM v0 as integrated onto the SiFive FU540 chip, and "sifive,pwm0" for the + SiFive PWM v0 IP block with no chip integration tweaks. + Please refer to sifive-blocks-ip-versioning.txt for details. +- reg: physical base address and length of the controller's registers +- clocks: Should contain a clock identifier for the PWM's parent clock. +- #pwm-cells: Should be 3. See pwm.txt in this directory + for a description of the cell format. +- interrupts: one interrupt per PWM channel + +Examples: + +pwm: pwm@10020000 { + compatible = "sifive,fu540-c000-pwm", "sifive,pwm0"; + reg = <0x0 0x10020000 0x0 0x1000>; + clocks = <&tlclk>; + interrupt-parent = <&plic>; + interrupts = <42 43 44 45>; + #pwm-cells = <3>; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt index bd23302e84be..6521bc44a74e 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt @@ -11,8 +11,10 @@ Required parameters: bindings defined in pwm.txt. Optional properties: -- pinctrl-names: Set to "default". -- pinctrl-0: Phandle pointing to pin configuration node for PWM. +- pinctrl-names: Set to "default". An additional "sleep" state can be + defined to set pins in sleep state when in low power. +- pinctrl-n: Phandle(s) pointing to pin configuration node for PWM, + respectively for "default" and "sleep" states. Example: timer@40002400 { @@ -21,7 +23,8 @@ Example: pwm { compatible = "st,stm32-pwm-lp"; #pwm-cells = <3>; - pinctrl-names = "default"; + pinctrl-names = "default", "sleep"; pinctrl-0 = <&lppwm1_pins>; + pinctrl-1 = <&lppwm1_sleep_pins>; }; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt index 3e6d55018d7a..a8690bfa5e1f 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt @@ -8,6 +8,8 @@ Required parameters: - pinctrl-names: Set to "default". - pinctrl-0: List of phandles pointing to pin configuration nodes for PWM module. For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt +- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells + bindings defined in pwm.txt. Optional parameters: - st,breakinput: One or two <index level filter> to describe break input configurations. @@ -28,6 +30,7 @@ Example: pwm { compatible = "st,stm32-pwm"; + #pwm-cells = <3>; pinctrl-0 = <&pwm1_pins>; pinctrl-names = "default"; st,breakinput = <0 1 5>; diff --git a/Documentation/devicetree/bindings/regulator/arizona-regulator.txt b/Documentation/devicetree/bindings/regulator/arizona-regulator.txt index 443564d7784f..69bf41949b01 100644 --- a/Documentation/devicetree/bindings/regulator/arizona-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/arizona-regulator.txt @@ -5,7 +5,8 @@ of analogue I/O. This document lists regulator specific bindings, see the primary binding document: - ../mfd/arizona.txt + For Wolfson Microelectronic Arizona codecs: ../mfd/arizona.txt + For Cirrus Logic Madera codecs: ../mfd/madera.txt Optional properties: - wlf,ldoena : GPIO specifier for the GPIO controlling LDOENA diff --git a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml index d289c2f7455a..a650b457085d 100644 --- a/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml +++ b/Documentation/devicetree/bindings/regulator/fixed-regulator.yaml @@ -12,10 +12,13 @@ maintainers: description: Any property defined as part of the core regulator binding, defined in - regulator.txt, can also be used. However a fixed voltage regulator is + regulator.yaml, can also be used. However a fixed voltage regulator is expected to have the regulator-min-microvolt and regulator-max-microvolt to be the same. +allOf: + - $ref: "regulator.yaml#" + properties: compatible: const: regulator-fixed diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt b/Documentation/devicetree/bindings/regulator/gpio-regulator.txt deleted file mode 100644 index dd25e73b5d79..000000000000 --- a/Documentation/devicetree/bindings/regulator/gpio-regulator.txt +++ /dev/null @@ -1,57 +0,0 @@ -GPIO controlled regulators - -Required properties: -- compatible : Must be "regulator-gpio". -- regulator-name : Defined in regulator.txt as optional, but required - here. -- gpios : Array of one or more GPIO pins used to select the - regulator voltage/current listed in "states". -- states : Selection of available voltages/currents provided by - this regulator and matching GPIO configurations to - achieve them. If there are no states in the "states" - array, use a fixed regulator instead. - -Optional properties: -- enable-gpios : GPIO used to enable/disable the regulator. - Warning, the GPIO phandle flags are ignored and the - GPIO polarity is controlled solely by the presence - of "enable-active-high" DT property. This is due to - compatibility with old DTs. -- enable-active-high : Polarity of "enable-gpio" GPIO is active HIGH. - Default is active LOW. -- gpios-states : On operating systems, that don't support reading back - gpio values in output mode (most notably linux), this - array provides the state of GPIO pins set when - requesting them from the gpio controller. Systems, - that are capable of preserving state when requesting - the lines, are free to ignore this property. - 0: LOW, 1: HIGH. Default is LOW if nothing else - is specified. -- startup-delay-us : Startup time in microseconds. -- regulator-type : Specifies what is being regulated, must be either - "voltage" or "current", defaults to voltage. - -Any property defined as part of the core regulator binding defined in -regulator.txt can also be used. - -Example: - - mmciv: gpio-regulator { - compatible = "regulator-gpio"; - - regulator-name = "mmci-gpio-supply"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2600000>; - regulator-boot-on; - - enable-gpios = <&gpio0 23 0x4>; - gpios = <&gpio0 24 0x4 - &gpio0 25 0x4>; - states = <1800000 0x3 - 2200000 0x2 - 2600000 0x1 - 2900000 0x0>; - - startup-delay-us = <100000>; - enable-active-high; - }; diff --git a/Documentation/devicetree/bindings/regulator/gpio-regulator.yaml b/Documentation/devicetree/bindings/regulator/gpio-regulator.yaml new file mode 100644 index 000000000000..9d3b28417fb6 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/gpio-regulator.yaml @@ -0,0 +1,118 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/gpio-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: GPIO controlled regulators + +maintainers: + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + +description: + Any property defined as part of the core regulator binding, defined in + regulator.txt, can also be used. + +allOf: + - $ref: "regulator.yaml#" + +properties: + compatible: + const: regulator-gpio + + regulator-name: true + + enable-gpios: + description: GPIO to use to enable/disable the regulator. + Warning, the GPIO phandle flags are ignored and the GPIO polarity is + controlled solely by the presence of "enable-active-high" DT property. + This is due to compatibility with old DTs. + maxItems: 1 + + gpios: + description: Array of one or more GPIO pins used to select the regulator + voltage/current listed in "states". + minItems: 1 + maxItems: 8 # Should be enough... + + gpios-states: + description: | + On operating systems, that don't support reading back gpio values in + output mode (most notably linux), this array provides the state of GPIO + pins set when requesting them from the gpio controller. Systems, that are + capable of preserving state when requesting the lines, are free to ignore + this property. + 0: LOW + 1: HIGH + Default is LOW if nothing else is specified. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - maxItems: 8 + items: + enum: [ 0, 1 ] + default: 0 + + states: + description: Selection of available voltages/currents provided by this + regulator and matching GPIO configurations to achieve them. If there are + no states in the "states" array, use a fixed regulator instead. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-matrix + - maxItems: 8 + items: + items: + - description: Voltage in microvolts + - description: GPIO group state value + + startup-delay-us: + description: startup time in microseconds + + enable-active-high: + description: Polarity of "enable-gpio" GPIO is active HIGH. Default is + active LOW. + type: boolean + + gpio-open-drain: + description: + GPIO is open drain type. If this property is missing then default + assumption is false. + type: boolean + + regulator-type: + description: Specifies what is being regulated. + allOf: + - $ref: /schemas/types.yaml#/definitions/string + - enum: + - voltage + - current + default: voltage + +required: + - compatible + - regulator-name + - gpios + - states + +examples: + - | + gpio-regulator { + compatible = "regulator-gpio"; + + regulator-name = "mmci-gpio-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2600000>; + regulator-boot-on; + + enable-gpios = <&gpio0 23 0x4>; + gpios = <&gpio0 24 0x4 + &gpio0 25 0x4>; + states = <1800000 0x3>, + <2200000 0x2>, + <2600000 0x1>, + <2900000 0x0>; + + startup-delay-us = <100000>; + enable-active-high; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/max8660.txt b/Documentation/devicetree/bindings/regulator/max8660.txt deleted file mode 100644 index 8ba994d8a142..000000000000 --- a/Documentation/devicetree/bindings/regulator/max8660.txt +++ /dev/null @@ -1,47 +0,0 @@ -Maxim MAX8660 voltage regulator - -Required properties: -- compatible: must be one of "maxim,max8660", "maxim,max8661" -- reg: I2C slave address, usually 0x34 -- any required generic properties defined in regulator.txt - -Example: - - i2c_master { - max8660@34 { - compatible = "maxim,max8660"; - reg = <0x34>; - - regulators { - regulator@0 { - regulator-compatible= "V3(DCDC)"; - regulator-min-microvolt = <725000>; - regulator-max-microvolt = <1800000>; - }; - - regulator@1 { - regulator-compatible= "V4(DCDC)"; - regulator-min-microvolt = <725000>; - regulator-max-microvolt = <1800000>; - }; - - regulator@2 { - regulator-compatible= "V5(LDO)"; - regulator-min-microvolt = <1700000>; - regulator-max-microvolt = <2000000>; - }; - - regulator@3 { - regulator-compatible= "V6(LDO)"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - }; - - regulator@4 { - regulator-compatible= "V7(LDO)"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - }; - }; - }; - }; diff --git a/Documentation/devicetree/bindings/regulator/max8660.yaml b/Documentation/devicetree/bindings/regulator/max8660.yaml new file mode 100644 index 000000000000..9c038698f880 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max8660.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/max8660.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Maxim MAX8660 voltage regulator + +maintainers: + - Daniel Mack <zonque@gmail.com> + +properties: + $nodename: + pattern: "pmic@[0-9a-f]{1,2}" + compatible: + enum: + - maxim,max8660 + - maxim,max8661 + + reg: + maxItems: 1 + + regulators: + type: object + + patternProperties: + "regulator-.+": + $ref: "regulator.yaml#" + + additionalProperties: false + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@34 { + compatible = "maxim,max8660"; + reg = <0x34>; + + regulators { + regulator-V3 { + regulator-compatible= "V3(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator-V4 { + regulator-compatible= "V4(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator-V5 { + regulator-compatible= "V5(LDO)"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + }; + + regulator-V6 { + regulator-compatible= "V6(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + regulator-V7 { + regulator-compatible= "V7(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 406f2e570c50..430b8622bda1 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -4,11 +4,13 @@ Qualcomm SPMI Regulators Usage: required Value type: <string> Definition: must be one of: + "qcom,pm8005-regulators" "qcom,pm8841-regulators" "qcom,pm8916-regulators" "qcom,pm8941-regulators" "qcom,pm8994-regulators" "qcom,pmi8994-regulators" + "qcom,pms405-regulators" - interrupts: Usage: optional @@ -110,6 +112,23 @@ Qualcomm SPMI Regulators Definition: Reference to regulator supplying the input pin, as described in the data sheet. +- vdd_l1_l2-supply: +- vdd_l3_l8-supply: +- vdd_l4-supply: +- vdd_l5_l6-supply: +- vdd_l10_l11_l12_l13-supply: +- vdd_l7-supply: +- vdd_l9-supply: +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply + Usage: optional (pms405 only) + Value type: <phandle> + Definition: Reference to regulator supplying the input pin, as + described in the data sheet. + - qcom,saw-reg: Usage: optional Value type: <phandle> @@ -120,6 +139,9 @@ The regulator node houses sub-nodes for each regulator within the device. Each sub-node is identified using the node's name, with valid values listed for each of the PMICs below. +pm8005: + s1, s2, s3, s4 + pm8841: s1, s2, s3, s4, s5, s6, s7, s8 diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 0a3f087d5844..487ccd8370b3 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -1,139 +1 @@ -Voltage/Current Regulators - -Optional properties: -- regulator-name: A string used as a descriptive name for regulator outputs -- regulator-min-microvolt: smallest voltage consumers may set -- regulator-max-microvolt: largest voltage consumers may set -- regulator-microvolt-offset: Offset applied to voltages to compensate for voltage drops -- regulator-min-microamp: smallest current consumers may set -- regulator-max-microamp: largest current consumers may set -- regulator-input-current-limit-microamp: maximum input current regulator allows -- regulator-always-on: boolean, regulator should never be disabled -- regulator-boot-on: bootloader/firmware enabled regulator -- regulator-allow-bypass: allow the regulator to go into bypass mode -- regulator-allow-set-load: allow the regulator performance level to be configured -- <name>-supply: phandle to the parent supply/regulator node -- regulator-ramp-delay: ramp delay for regulator(in uV/us) - For hardware which supports disabling ramp rate, it should be explicitly - initialised to zero (regulator-ramp-delay = <0>) for disabling ramp delay. -- regulator-enable-ramp-delay: The time taken, in microseconds, for the supply - rail to reach the target voltage, plus/minus whatever tolerance the board - design requires. This property describes the total system ramp time - required due to the combination of internal ramping of the regulator itself, - and board design issues such as trace capacitance and load on the supply. -- regulator-settling-time-us: Settling time, in microseconds, for voltage - change if regulator have the constant time for any level voltage change. - This is useful when regulator have exponential voltage change. -- regulator-settling-time-up-us: Settling time, in microseconds, for voltage - increase if the regulator needs a constant time to settle after voltage - increases of any level. This is useful for regulators with exponential - voltage changes. -- regulator-settling-time-down-us: Settling time, in microseconds, for voltage - decrease if the regulator needs a constant time to settle after voltage - decreases of any level. This is useful for regulators with exponential - voltage changes. -- regulator-soft-start: Enable soft start so that voltage ramps slowly -- regulator-state-standby sub-root node for Standby mode - : equivalent with standby Linux sleep state, which provides energy savings - with a relatively quick transition back time. -- regulator-state-mem sub-root node for Suspend-to-RAM mode - : suspend to memory, the device goes to sleep, but all data stored in memory, - only some external interrupt can wake the device. -- regulator-state-disk sub-root node for Suspend-to-DISK mode - : suspend to disk, this state operates similarly to Suspend-to-RAM, - but includes a final step of writing memory contents to disk. -- regulator-state-[mem/disk/standby] node has following common properties: - - regulator-on-in-suspend: regulator should be on in suspend state. - - regulator-off-in-suspend: regulator should be off in suspend state. - - regulator-suspend-min-microvolt: minimum voltage may be set in - suspend state. - - regulator-suspend-max-microvolt: maximum voltage may be set in - suspend state. - - regulator-suspend-microvolt: the default voltage which regulator - would be set in suspend. This property is now deprecated, instead - setting voltage for suspend mode via the API which regulator - driver provides is recommended. - - regulator-changeable-in-suspend: whether the default voltage and - the regulator on/off in suspend can be changed in runtime. - - regulator-mode: operating mode in the given suspend state. - The set of possible operating modes depends on the capabilities of - every hardware so the valid modes are documented on each regulator - device tree binding document. -- regulator-initial-mode: initial operating mode. The set of possible operating - modes depends on the capabilities of every hardware so each device binding - documentation explains which values the regulator supports. -- regulator-allowed-modes: list of operating modes that software is allowed to - configure for the regulator at run-time. Elements may be specified in any - order. The set of possible operating modes depends on the capabilities of - every hardware so each device binding document explains which values the - regulator supports. -- regulator-system-load: Load in uA present on regulator that is not captured by - any consumer request. -- regulator-pull-down: Enable pull down resistor when the regulator is disabled. -- regulator-over-current-protection: Enable over current protection. -- regulator-active-discharge: tristate, enable/disable active discharge of - regulators. The values are: - 0: Disable active discharge. - 1: Enable active discharge. - Absence of this property will leave configuration to default. -- regulator-coupled-with: Regulators with which the regulator - is coupled. The linkage is 2-way - all coupled regulators should be linked - with each other. A regulator should not be coupled with its supplier. -- regulator-coupled-max-spread: Array of maximum spread between voltages of - coupled regulators in microvolts, each value in the array relates to the - corresponding couple specified by the regulator-coupled-with property. -- regulator-max-step-microvolt: Maximum difference between current and target - voltages that can be changed safely in a single step. - -Deprecated properties: -- regulator-compatible: If a regulator chip contains multiple - regulators, and if the chip's binding contains a child node that - describes each regulator, then this property indicates which regulator - this child node is intended to configure. If this property is missing, - the node's name will be used instead. - -Example: - - xyzreg: regulator@0 { - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <2500000>; - regulator-always-on; - vin-supply = <&vin>; - - regulator-state-mem { - regulator-on-in-suspend; - }; - }; - -Regulator Consumers: -Consumer nodes can reference one or more of its supplies/ -regulators using the below bindings. - -- <name>-supply: phandle to the regulator node - -These are the same bindings that a regulator in the above -example used to reference its own supply, in which case -its just seen as a special case of a regulator being a -consumer itself. - -Example of a consumer device node (mmc) referencing two -regulators (twl_reg1 and twl_reg2), - - twl_reg1: regulator@0 { - ... - ... - ... - }; - - twl_reg2: regulator@1 { - ... - ... - ... - }; - - mmc: mmc@0 { - ... - ... - vmmc-supply = <&twl_reg1>; - vmmcaux-supply = <&twl_reg2>; - }; +This file has moved to regulator.yaml. diff --git a/Documentation/devicetree/bindings/regulator/regulator.yaml b/Documentation/devicetree/bindings/regulator/regulator.yaml new file mode 100644 index 000000000000..02c3043ce419 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator.yaml @@ -0,0 +1,200 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Voltage/Current Regulators + +maintainers: + - Liam Girdwood <lgirdwood@gmail.com> + - Mark Brown <broonie@kernel.org> + +properties: + regulator-name: + description: A string used as a descriptive name for regulator outputs + $ref: "/schemas/types.yaml#/definitions/string" + + regulator-min-microvolt: + description: smallest voltage consumers may set + + regulator-max-microvolt: + description: largest voltage consumers may set + + regulator-microvolt-offset: + description: Offset applied to voltages to compensate for voltage drops + + regulator-min-microamp: + description: smallest current consumers may set + + regulator-max-microamp: + description: largest current consumers may set + + regulator-input-current-limit-microamp: + description: maximum input current regulator allows + + regulator-always-on: + description: boolean, regulator should never be disabled + type: boolean + + regulator-boot-on: + description: bootloader/firmware enabled regulator + type: boolean + + regulator-allow-bypass: + description: allow the regulator to go into bypass mode + type: boolean + + regulator-allow-set-load: + description: allow the regulator performance level to be configured + type: boolean + + regulator-ramp-delay: + description: ramp delay for regulator(in uV/us) For hardware which supports + disabling ramp rate, it should be explicitly initialised to zero (regulator-ramp-delay + = <0>) for disabling ramp delay. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-enable-ramp-delay: + description: The time taken, in microseconds, for the supply rail to + reach the target voltage, plus/minus whatever tolerance the board + design requires. This property describes the total system ramp time + required due to the combination of internal ramping of the regulator + itself, and board design issues such as trace capacitance and load + on the supply. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-settling-time-us: + description: Settling time, in microseconds, for voltage change if regulator + have the constant time for any level voltage change. This is useful + when regulator have exponential voltage change. + + regulator-settling-time-up-us: + description: Settling time, in microseconds, for voltage increase if + the regulator needs a constant time to settle after voltage increases + of any level. This is useful for regulators with exponential voltage + changes. + + regulator-settling-time-down-us: + description: Settling time, in microseconds, for voltage decrease if + the regulator needs a constant time to settle after voltage decreases + of any level. This is useful for regulators with exponential voltage + changes. + + regulator-soft-start: + description: Enable soft start so that voltage ramps slowly + type: boolean + + regulator-initial-mode: + description: initial operating mode. The set of possible operating modes + depends on the capabilities of every hardware so each device binding + documentation explains which values the regulator supports. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-allowed-modes: + description: list of operating modes that software is allowed to configure + for the regulator at run-time. Elements may be specified in any order. + The set of possible operating modes depends on the capabilities of + every hardware so each device binding document explains which values + the regulator supports. + $ref: "/schemas/types.yaml#/definitions/uint32-array" + + regulator-system-load: + description: Load in uA present on regulator that is not captured by + any consumer request. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-pull-down: + description: Enable pull down resistor when the regulator is disabled. + type: boolean + + regulator-over-current-protection: + description: Enable over current protection. + type: boolean + + regulator-active-discharge: + description: | + tristate, enable/disable active discharge of regulators. The values are: + 0: Disable active discharge. + 1: Enable active discharge. + Absence of this property will leave configuration to default. + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 0, 1 ] + + regulator-coupled-with: + description: Regulators with which the regulator is coupled. The linkage + is 2-way - all coupled regulators should be linked with each other. + A regulator should not be coupled with its supplier. + $ref: "/schemas/types.yaml#/definitions/phandle-array" + + regulator-coupled-max-spread: + description: Array of maximum spread between voltages of coupled regulators + in microvolts, each value in the array relates to the corresponding + couple specified by the regulator-coupled-with property. + $ref: "/schemas/types.yaml#/definitions/uint32" + + regulator-max-step-microvolt: + description: Maximum difference between current and target voltages + that can be changed safely in a single step. + +patternProperties: + ".*-supply$": + description: Input supply phandle(s) for this node + + regulator-state-(standby|mem|disk): + type: object + description: + sub-nodes for regulator state in Standby, Suspend-to-RAM, and + Suspend-to-DISK modes. Equivalent with standby, mem, and disk Linux + sleep states. + + properties: + regulator-on-in-suspend: + description: regulator should be on in suspend state. + type: boolean + + regulator-off-in-suspend: + description: regulator should be off in suspend state. + type: boolean + + regulator-suspend-min-microvolt: + description: minimum voltage may be set in suspend state. + + regulator-suspend-max-microvolt: + description: maximum voltage may be set in suspend state. + + regulator-suspend-microvolt: + description: the default voltage which regulator would be set in + suspend. This property is now deprecated, instead setting voltage + for suspend mode via the API which regulator driver provides is + recommended. + + regulator-changeable-in-suspend: + description: whether the default voltage and the regulator on/off + in suspend can be changed in runtime. + type: boolean + + regulator-mode: + description: operating mode in the given suspend state. The set + of possible operating modes depends on the capabilities of every + hardware so the valid modes are documented on each regulator device + tree binding document. + $ref: "/schemas/types.yaml#/definitions/uint32" + + additionalProperties: false + +examples: + - | + xyzreg: regulator@0 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + vin-supply = <&vin>; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/regulator/slg51000.txt b/Documentation/devicetree/bindings/regulator/slg51000.txt new file mode 100644 index 000000000000..aa0733e49b90 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/slg51000.txt @@ -0,0 +1,88 @@ +* Dialog Semiconductor SLG51000 Voltage Regulator + +Required properties: +- compatible : Should be "dlg,slg51000" for SLG51000 +- reg : Specifies the I2C slave address. +- xxx-supply: Input voltage supply regulator for ldo3 to ldo7. + These entries are required if regulators are enabled for a device. + An absence of these properties can cause the regulator registration to fail. + If some of input supply is powered through battery or always-on supply then + also it is required to have these parameters with proper node handle of always + on power supply. + vin3-supply: Input supply for ldo3 + vin4-supply: Input supply for ldo4 + vin5-supply: Input supply for ldo5 + vin6-supply: Input supply for ldo6 + vin7-supply: Input supply for ldo7 + +Optional properties: +- interrupt-parent : Specifies the reference to the interrupt controller. +- interrupts : IRQ line information. +- dlg,cs-gpios : Specify a valid GPIO for chip select + +Sub-nodes: +- regulators : This node defines the settings for the regulators. + The content of the sub-node is defined by the standard binding + for regulators; see regulator.txt. + + The SLG51000 regulators are bound using their names listed below: + ldo1 + ldo2 + ldo3 + ldo4 + ldo5 + ldo6 + ldo7 + +Optional properties for regulators: +- enable-gpios : Specify a valid GPIO for platform control of the regulator. + +Example: + pmic: slg51000@75 { + compatible = "dlg,slg51000"; + reg = <0x75>; + + regulators { + ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3300000>; + }; + + ldo2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3300000>; + }; + + ldo3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + + ldo4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + + ldo5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1200000>; + }; + + ldo6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1200000>; + }; + + ldo7 { + regulator-name = "ldo7"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3750000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/st,stm32-booster.txt b/Documentation/devicetree/bindings/regulator/st,stm32-booster.txt new file mode 100644 index 000000000000..479ad4c8758e --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/st,stm32-booster.txt @@ -0,0 +1,18 @@ +STM32 BOOSTER - Booster for ADC analog input switches + +Some STM32 devices embed a 3.3V booster supplied by Vdda, that can be used +to supply ADC analog input switches. + +Required properties: +- compatible: Should be one of: + "st,stm32h7-booster" + "st,stm32mp1-booster" +- st,syscfg: Phandle to system configuration controller. +- vdda-supply: Phandle to the vdda input analog voltage. + +Example: + booster: regulator-booster { + compatible = "st,stm32mp1-booster"; + st,syscfg = <&syscfg>; + vdda-supply = <&vdda>; + }; diff --git a/Documentation/devicetree/bindings/riscv/cpus.yaml b/Documentation/devicetree/bindings/riscv/cpus.yaml new file mode 100644 index 000000000000..f97a4ecd7b91 --- /dev/null +++ b/Documentation/devicetree/bindings/riscv/cpus.yaml @@ -0,0 +1,170 @@ +# SPDX-License-Identifier: (GPL-2.0 OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/riscv/cpus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RISC-V bindings for 'cpus' DT nodes + +maintainers: + - Paul Walmsley <paul.walmsley@sifive.com> + - Palmer Dabbelt <palmer@sifive.com> + +allOf: + - $ref: /schemas/cpus.yaml# + +properties: + $nodename: + const: cpus + description: Container of cpu nodes + + '#address-cells': + const: 1 + description: | + A single unsigned 32-bit integer uniquely identifies each RISC-V + hart in a system. (See the "reg" node under the "cpu" node, + below). + + '#size-cells': + const: 0 + +patternProperties: + '^cpu@[0-9a-f]+$': + properties: + compatible: + type: array + items: + - enum: + - sifive,rocket0 + - sifive,e5 + - sifive,e51 + - sifive,u54-mc + - sifive,u54 + - sifive,u5 + - const: riscv + description: + Identifies that the hart uses the RISC-V instruction set + and identifies the type of the hart. + + mmu-type: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: + - riscv,sv32 + - riscv,sv39 + - riscv,sv48 + description: + Identifies the MMU address translation mode used on this + hart. These values originate from the RISC-V Privileged + Specification document, available from + https://riscv.org/specifications/ + + riscv,isa: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: + - rv64imac + - rv64imafdc + description: + Identifies the specific RISC-V instruction set architecture + supported by the hart. These are documented in the RISC-V + User-Level ISA document, available from + https://riscv.org/specifications/ + + timebase-frequency: + type: integer + minimum: 1 + description: + Specifies the clock frequency of the system timer in Hz. + This value is common to all harts on a single system image. + + interrupt-controller: + type: object + description: Describes the CPU's local interrupt controller + + properties: + '#interrupt-cells': + const: 1 + + compatible: + const: riscv,cpu-intc + + interrupt-controller: true + + required: + - '#interrupt-cells' + - compatible + - interrupt-controller + + required: + - riscv,isa + - timebase-frequency + - interrupt-controller + +examples: + - | + // Example 1: SiFive Freedom U540G Development Kit + cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <1000000>; + cpu@0 { + clock-frequency = <0>; + compatible = "sifive,rocket0", "riscv"; + device_type = "cpu"; + i-cache-block-size = <64>; + i-cache-sets = <128>; + i-cache-size = <16384>; + reg = <0>; + riscv,isa = "rv64imac"; + cpu_intc0: interrupt-controller { + #interrupt-cells = <1>; + compatible = "riscv,cpu-intc"; + interrupt-controller; + }; + }; + cpu@1 { + clock-frequency = <0>; + compatible = "sifive,rocket0", "riscv"; + d-cache-block-size = <64>; + d-cache-sets = <64>; + d-cache-size = <32768>; + d-tlb-sets = <1>; + d-tlb-size = <32>; + device_type = "cpu"; + i-cache-block-size = <64>; + i-cache-sets = <64>; + i-cache-size = <32768>; + i-tlb-sets = <1>; + i-tlb-size = <32>; + mmu-type = "riscv,sv39"; + reg = <1>; + riscv,isa = "rv64imafdc"; + tlb-split; + cpu_intc1: interrupt-controller { + #interrupt-cells = <1>; + compatible = "riscv,cpu-intc"; + interrupt-controller; + }; + }; + }; + + - | + // Example 2: Spike ISA Simulator with 1 Hart + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + device_type = "cpu"; + reg = <0>; + compatible = "riscv"; + riscv,isa = "rv64imafdc"; + mmu-type = "riscv,sv48"; + interrupt-controller { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "riscv,cpu-intc"; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/riscv/sifive.yaml b/Documentation/devicetree/bindings/riscv/sifive.yaml new file mode 100644 index 000000000000..9d17dc2f3f84 --- /dev/null +++ b/Documentation/devicetree/bindings/riscv/sifive.yaml @@ -0,0 +1,25 @@ +# SPDX-License-Identifier: (GPL-2.0 OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/riscv/sifive.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SiFive SoC-based boards + +maintainers: + - Paul Walmsley <paul.walmsley@sifive.com> + - Palmer Dabbelt <palmer@sifive.com> + +description: + SiFive SoC-based boards + +properties: + $nodename: + const: '/' + compatible: + items: + - enum: + - sifive,freedom-unleashed-a00 + - const: sifive,fu540-c000 + - const: sifive,fu540 +... diff --git a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt index 0014da9145af..c223e54452da 100644 --- a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt +++ b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt @@ -2,6 +2,7 @@ HWRNG support for the iproc-rng200 driver Required properties: - compatible : Must be one of: + "brcm,bcm7211-rng200" "brcm,bcm7278-rng200" "brcm,iproc-rng200" - reg : base address and size of control register block diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml new file mode 100644 index 000000000000..c374fd4923a6 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/allwinner,sun4i-a10-spi.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/allwinner,sun4i-a10-spi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 SPI Controller Device Tree Bindings + +allOf: + - $ref: "spi-controller.yaml" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#address-cells": true + "#size-cells": true + + compatible: + const: allwinner,sun4i-a10-spi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: ahb + - const: mod + + dmas: + items: + - description: RX DMA Channel + - description: TX DMA Channel + + dma-names: + items: + - const: rx + - const: tx + + num-cs: true + +patternProperties: + "^.*@[0-9a-f]+": + properties: + reg: + items: + minimum: 0 + maximum: 4 + + spi-rx-bus-width: + const: 1 + + spi-tx-bus-width: + const: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + spi1: spi@1c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <11>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + #address-cells = <1>; + #size-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml new file mode 100644 index 000000000000..bda7a5befd8b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml @@ -0,0 +1,106 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/allwinner,sun6i-a31-spi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 SPI Controller Device Tree Bindings + +allOf: + - $ref: "spi-controller.yaml" + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <maxime.ripard@bootlin.com> + +properties: + "#address-cells": true + "#size-cells": true + + compatible: + enum: + - allwinner,sun6i-a31-spi + - allwinner,sun8i-h3-spi + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: ahb + - const: mod + + resets: + maxItems: 1 + + dmas: + items: + - description: RX DMA Channel + - description: TX DMA Channel + + dma-names: + items: + - const: rx + - const: tx + + num-cs: true + +patternProperties: + "^.*@[0-9a-f]+": + properties: + reg: + items: + minimum: 0 + maximum: 4 + + spi-rx-bus-width: + const: 1 + + spi-tx-bus-width: + const: 1 + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + spi1: spi@1c69000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c69000 0x1000>; + interrupts = <0 66 4>; + clocks = <&ahb1_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 21>; + #address-cells = <1>; + #size-cells = <0>; + }; + + - | + spi0: spi@1c68000 { + compatible = "allwinner,sun8i-h3-spi"; + reg = <0x01c68000 0x1000>; + interrupts = <0 65 4>; + clocks = <&ccu 30>, <&ccu 82>; + clock-names = "ahb", "mod"; + dmas = <&dma 23>, <&dma 23>; + dma-names = "rx", "tx"; + resets = <&ccu 15>; + #address-cells = <1>; + #size-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/spi/spi-bus.txt b/Documentation/devicetree/bindings/spi/spi-bus.txt index 1f6e86f787ef..e07783505498 100644 --- a/Documentation/devicetree/bindings/spi/spi-bus.txt +++ b/Documentation/devicetree/bindings/spi/spi-bus.txt @@ -1,111 +1 @@ -SPI (Serial Peripheral Interface) busses - -SPI busses can be described with a node for the SPI controller device -and a set of child nodes for each SPI slave on the bus. The system's SPI -controller may be described for use in SPI master mode or in SPI slave mode, -but not for both at the same time. - -The SPI controller node requires the following properties: -- compatible - Name of SPI bus controller following generic names - recommended practice. - -In master mode, the SPI controller node requires the following additional -properties: -- #address-cells - number of cells required to define a chip select - address on the SPI bus. -- #size-cells - should be zero. - -In slave mode, the SPI controller node requires one additional property: -- spi-slave - Empty property. - -No other properties are required in the SPI bus node. It is assumed -that a driver for an SPI bus device will understand that it is an SPI bus. -However, the binding does not attempt to define the specific method for -assigning chip select numbers. Since SPI chip select configuration is -flexible and non-standardized, it is left out of this binding with the -assumption that board specific platform code will be used to manage -chip selects. Individual drivers can define additional properties to -support describing the chip select layout. - -Optional properties (master mode only): -- cs-gpios - gpios chip select. -- num-cs - total number of chipselects. - -If cs-gpios is used the number of chip selects will be increased automatically -with max(cs-gpios > hw cs). - -So if for example the controller has 2 CS lines, and the cs-gpios -property looks like this: - -cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>; - -Then it should be configured so that num_chipselect = 4 with the -following mapping: - -cs0 : &gpio1 0 0 -cs1 : native -cs2 : &gpio1 1 0 -cs3 : &gpio1 2 0 - - -SPI slave nodes must be children of the SPI controller node. - -In master mode, one or more slave nodes (up to the number of chip selects) can -be present. Required properties are: -- compatible - Name of SPI device following generic names recommended - practice. -- reg - Chip select address of device. -- spi-max-frequency - Maximum SPI clocking speed of device in Hz. - -In slave mode, the (single) slave node is optional. -If present, it must be called "slave". Required properties are: -- compatible - Name of SPI device following generic names recommended - practice. - -All slave nodes can contain the following optional properties: -- spi-cpol - Empty property indicating device requires inverse clock - polarity (CPOL) mode. -- spi-cpha - Empty property indicating device requires shifted clock - phase (CPHA) mode. -- spi-cs-high - Empty property indicating device requires chip select - active high. -- spi-3wire - Empty property indicating device requires 3-wire mode. -- spi-lsb-first - Empty property indicating device requires LSB first mode. -- spi-tx-bus-width - The bus width (number of data wires) that is used for MOSI. - Defaults to 1 if not present. -- spi-rx-bus-width - The bus width (number of data wires) that is used for MISO. - Defaults to 1 if not present. -- spi-rx-delay-us - Microsecond delay after a read transfer. -- spi-tx-delay-us - Microsecond delay after a write transfer. - -Some SPI controllers and devices support Dual and Quad SPI transfer mode. -It allows data in the SPI system to be transferred using 2 wires (DUAL) or 4 -wires (QUAD). -Now the value that spi-tx-bus-width and spi-rx-bus-width can receive is -only 1 (SINGLE), 2 (DUAL) and 4 (QUAD). -Dual/Quad mode is not allowed when 3-wire mode is used. - -If a gpio chipselect is used for the SPI slave the gpio number will be passed -via the SPI master node cs-gpios property. - -SPI example for an MPC5200 SPI bus: - spi@f00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - interrupt-parent = <&mpc5200_pic>; - - ethernet-switch@0 { - compatible = "micrel,ks8995m"; - spi-max-frequency = <1000000>; - reg = <0>; - }; - - codec@1 { - compatible = "ti,tlv320aic26"; - spi-max-frequency = <100000>; - reg = <1>; - }; - }; +This file has moved to spi-controller.yaml. diff --git a/Documentation/devicetree/bindings/spi/spi-controller.yaml b/Documentation/devicetree/bindings/spi/spi-controller.yaml new file mode 100644 index 000000000000..876c0623f322 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-controller.yaml @@ -0,0 +1,161 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI Controller Generic Binding + +maintainers: + - Mark Brown <broonie@kernel.org> + +description: | + SPI busses can be described with a node for the SPI controller device + and a set of child nodes for each SPI slave on the bus. The system SPI + controller may be described for use in SPI master mode or in SPI slave mode, + but not for both at the same time. + +properties: + $nodename: + pattern: "^spi(@.*|-[0-9a-f])*$" + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + cs-gpios: + description: | + GPIOs used as chip selects. + If that property is used, the number of chip selects will be + increased automatically with max(cs-gpios, hardware chip selects). + + So if, for example, the controller has 2 CS lines, and the + cs-gpios looks like this + cs-gpios = <&gpio1 0 0>, <0>, <&gpio1 1 0>, <&gpio1 2 0>; + + Then it should be configured so that num_chipselect = 4, with + the following mapping + cs0 : &gpio1 0 0 + cs1 : native + cs2 : &gpio1 1 0 + cs3 : &gpio1 2 0 + + num-cs: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Total number of chip selects. + + spi-slave: + $ref: /schemas/types.yaml#/definitions/flag + description: + The SPI controller acts as a slave, instead of a master. + +patternProperties: + "^slave$": + type: object + + properties: + compatible: + description: + Compatible of the SPI device. + + required: + - compatible + + "^.*@[0-9a-f]+$": + type: object + + properties: + compatible: + description: + Compatible of the SPI device. + + reg: + maxItems: 1 + minimum: 0 + maximum: 256 + description: + Chip select used by the device. + + spi-3wire: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires 3-wire mode. + + spi-cpha: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires shifted clock phase (CPHA) mode. + + spi-cpol: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires inverse clock polarity (CPOL) mode. + + spi-cs-high: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires the chip select active high. + + spi-lsb-first: + $ref: /schemas/types.yaml#/definitions/flag + description: + The device requires the LSB first mode. + + spi-max-frequency: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + Maximum SPI clocking speed of the device in Hz. + + spi-rx-bus-width: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 1, 2, 4 ] + - default: 1 + description: + Bus width to the SPI bus used for MISO. + + spi-rx-delay-us: + description: + Delay, in microseconds, after a read transfer. + + spi-tx-bus-width: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 1, 2, 4 ] + - default: 1 + description: + Bus width to the SPI bus used for MOSI. + + spi-tx-delay-us: + description: + Delay, in microseconds, after a write transfer. + + required: + - compatible + - reg + +examples: + - | + spi@f00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + + ethernet-switch@0 { + compatible = "micrel,ks8995m"; + spi-max-frequency = <1000000>; + reg = <0>; + }; + + codec@1 { + compatible = "ti,tlv320aic26"; + spi-max-frequency = <100000>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.txt b/Documentation/devicetree/bindings/spi/spi-gpio.txt deleted file mode 100644 index 52db562f17a4..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-gpio.txt +++ /dev/null @@ -1,43 +0,0 @@ -SPI-GPIO devicetree bindings - -This represents a group of 3-n GPIO lines used for bit-banged SPI on dedicated -GPIO lines. - -Required properties: - - - compatible: should be set to "spi-gpio" - - #address-cells: should be set to <0x1> - - ranges - - sck-gpios: GPIO spec for the SCK line to use - - miso-gpios: GPIO spec for the MISO line to use - - mosi-gpios: GPIO spec for the MOSI line to use - - cs-gpios: GPIOs to use for chipselect lines. - Not needed if num-chipselects = <0>. - - num-chipselects: Number of chipselect lines. Should be <0> if a single device - with no chip select is connected. - -Deprecated bindings: - -These legacy GPIO line bindings can alternatively be used to define the -GPIO lines used, they should not be used in new device trees. - - - gpio-sck: GPIO spec for the SCK line to use - - gpio-miso: GPIO spec for the MISO line to use - - gpio-mosi: GPIO spec for the MOSI line to use - -Example: - - spi { - compatible = "spi-gpio"; - #address-cells = <0x1>; - ranges; - - sck-gpios = <&gpio 95 0>; - miso-gpios = <&gpio 98 0>; - mosi-gpios = <&gpio 97 0>; - cs-gpios = <&gpio 125 0>; - num-chipselects = <1>; - - /* clients */ - }; - diff --git a/Documentation/devicetree/bindings/spi/spi-gpio.yaml b/Documentation/devicetree/bindings/spi/spi-gpio.yaml new file mode 100644 index 000000000000..55c4f1705f07 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-gpio.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SPI-GPIO devicetree bindings + +maintainers: + - Rob Herring <robh@kernel.org> + +description: + This represents a group of 3-n GPIO lines used for bit-banged SPI on + dedicated GPIO lines. + +allOf: + - $ref: "/schemas/spi/spi-controller.yaml#" + +properties: + compatible: + const: spi-gpio + + sck-gpios: + description: GPIO spec for the SCK line to use + maxItems: 1 + + miso-gpios: + description: GPIO spec for the MISO line to use + maxItems: 1 + + mosi-gpios: + description: GPIO spec for the MOSI line to use + maxItems: 1 + + cs-gpios: + description: GPIOs to use for chipselect lines. + Not needed if num-chipselects = <0>. + minItems: 1 + maxItems: 1024 + + num-chipselects: + description: Number of chipselect lines. Should be <0> if a single device + with no chip select is connected. + $ref: "/schemas/types.yaml#/definitions/uint32" + + # Deprecated properties + gpio-sck: false + gpio-miso: false + gpio-mosi: false + +required: + - compatible + - num-chipselects + - sck-gpios + +examples: + - | + spi { + compatible = "spi-gpio"; + #address-cells = <0x1>; + #size-cells = <0x0>; + + sck-gpios = <&gpio 95 0>; + miso-gpios = <&gpio 98 0>; + mosi-gpios = <&gpio 97 0>; + cs-gpios = <&gpio 125 0>; + num-chipselects = <1>; + + /* clients */ + }; + +... diff --git a/Documentation/devicetree/bindings/spi/spi-pl022.yaml b/Documentation/devicetree/bindings/spi/spi-pl022.yaml new file mode 100644 index 000000000000..dfb697c69341 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-pl022.yaml @@ -0,0 +1,165 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/spi-pl022.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM PL022 SPI controller + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +allOf: + - $ref: "spi-controller.yaml#" + +# We need a select here so we don't match all nodes with 'arm,primecell' +select: + properties: + compatible: + contains: + const: arm,pl022 + required: + - compatible + +properties: + compatible: + items: + - const: arm,pl022 + - const: arm,primecell + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 2 + + clock-names: + items: + - enum: + - SSPCLK + - sspclk + - const: apb_pclk + + pl022,autosuspend-delay: + description: delay in ms following transfer completion before the + runtime power management system suspends the device. A setting of 0 + indicates no delay and the device will be suspended immediately. + $ref: "/schemas/types.yaml#/definitions/uint32" + + pl022,rt: + description: indicates the controller should run the message pump with realtime + priority to minimise the transfer latency on the bus (boolean) + type: boolean + + dmas: + description: + Two or more DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt + minItems: 2 + maxItems: 32 + + dma-names: + description: + There must be at least one channel named "tx" for transmit and named "rx" + for receive. + minItems: 2 + maxItems: 32 + additionalItems: true + items: + - const: rx + - const: tx + +patternProperties: + "^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-f]+$": + type: object + # SPI slave nodes must be children of the SPI master node and can + # contain the following properties. + properties: + pl022,interface: + description: SPI interface type + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: + - 0 # SPI + - 1 # Texas Instruments Synchronous Serial Frame Format + - 2 # Microwire (Half Duplex) + + pl022,com-mode: + description: Specifies the transfer mode + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: + - 0 # interrupt mode + - 1 # polling mode + - 2 # DMA mode + default: 1 + + pl022,rx-level-trig: + description: Rx FIFO watermark level + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - minimum: 0 + maximum: 4 + + pl022,tx-level-trig: + description: Tx FIFO watermark level + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - minimum: 0 + maximum: 4 + + pl022,ctrl-len: + description: Microwire interface - Control length + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - minimum: 0x03 + maximum: 0x1f + + pl022,wait-state: + description: Microwire interface - Wait state + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 0, 1 ] + + pl022,duplex: + description: Microwire interface - Full/Half duplex + allOf: + - $ref: "/schemas/types.yaml#/definitions/uint32" + - enum: [ 0, 1 ] + +required: + - compatible + - reg + - interrupts + +examples: + - | + spi@e0100000 { + compatible = "arm,pl022", "arm,primecell"; + reg = <0xe0100000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <0 31 0x4>; + dmas = <&dma_controller 23 1>, + <&dma_controller 24 0>; + dma-names = "rx", "tx"; + + m25p80@1 { + compatible = "st,m25p80"; + reg = <1>; + spi-max-frequency = <12000000>; + spi-cpol; + spi-cpha; + pl022,interface = <0>; + pl022,com-mode = <0x2>; + pl022,rx-level-trig = <0>; + pl022,tx-level-trig = <0>; + pl022,ctrl-len = <0x11>; + pl022,wait-state = <0>; + pl022,duplex = <0>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt index adeeb63e84b9..bfc038b9478d 100644 --- a/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-stm32-qspi.txt @@ -19,8 +19,11 @@ Required properties: - reg: chip-Select number (QSPI controller may connect 2 flashes) - spi-max-frequency: max frequency of spi bus -Optional property: +Optional properties: - spi-rx-bus-width: see ./spi-bus.txt for the description +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, +Documentation/devicetree/bindings/dma/dma.txt. +- dma-names: DMA request names should include "tx" and "rx" if present. Example: diff --git a/Documentation/devicetree/bindings/spi/spi-sun4i.txt b/Documentation/devicetree/bindings/spi/spi-sun4i.txt deleted file mode 100644 index c75d604a8290..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-sun4i.txt +++ /dev/null @@ -1,23 +0,0 @@ -Allwinner A10 SPI controller - -Required properties: -- compatible: Should be "allwinner,sun4-a10-spi". -- reg: Should contain register location and length. -- interrupts: Should contain interrupt. -- clocks: phandle to the clocks feeding the SPI controller. Two are - needed: - - "ahb": the gated AHB parent clock - - "mod": the parent module clock -- clock-names: Must contain the clock names described just above - -Example: - -spi1: spi@1c06000 { - compatible = "allwinner,sun4i-a10-spi"; - reg = <0x01c06000 0x1000>; - interrupts = <11>; - clocks = <&ahb_gates 21>, <&spi1_clk>; - clock-names = "ahb", "mod"; - #address-cells = <1>; - #size-cells = <0>; -}; diff --git a/Documentation/devicetree/bindings/spi/spi-sun6i.txt b/Documentation/devicetree/bindings/spi/spi-sun6i.txt deleted file mode 100644 index 435a8e0731ac..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-sun6i.txt +++ /dev/null @@ -1,44 +0,0 @@ -Allwinner A31/H3 SPI controller - -Required properties: -- compatible: Should be "allwinner,sun6i-a31-spi" or "allwinner,sun8i-h3-spi". -- reg: Should contain register location and length. -- interrupts: Should contain interrupt. -- clocks: phandle to the clocks feeding the SPI controller. Two are - needed: - - "ahb": the gated AHB parent clock - - "mod": the parent module clock -- clock-names: Must contain the clock names described just above -- resets: phandle to the reset controller asserting this device in - reset - -Optional properties: -- dmas: DMA specifiers for rx and tx dma. See the DMA client binding, - Documentation/devicetree/bindings/dma/dma.txt -- dma-names: DMA request names should include "rx" and "tx" if present. - -Example: - -spi1: spi@1c69000 { - compatible = "allwinner,sun6i-a31-spi"; - reg = <0x01c69000 0x1000>; - interrupts = <0 66 4>; - clocks = <&ahb1_gates 21>, <&spi1_clk>; - clock-names = "ahb", "mod"; - resets = <&ahb1_rst 21>; -}; - -spi0: spi@1c68000 { - compatible = "allwinner,sun8i-h3-spi"; - reg = <0x01c68000 0x1000>; - interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>; - clock-names = "ahb", "mod"; - dmas = <&dma 23>, <&dma 23>; - dma-names = "rx", "tx"; - pinctrl-names = "default"; - pinctrl-0 = <&spi0_pins>; - resets = <&ccu RST_BUS_SPI0>; - #address-cells = <1>; - #size-cells = <0>; -}; diff --git a/Documentation/devicetree/bindings/spi/spi-synquacer.txt b/Documentation/devicetree/bindings/spi/spi-synquacer.txt new file mode 100644 index 000000000000..291dfa692d0a --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-synquacer.txt @@ -0,0 +1,27 @@ +* Socionext Synquacer HS-SPI bindings + +Required Properties: +- compatible: should be "socionext,synquacer-spi" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: should contain the "spi_rx", "spi_tx" and "spi_fault" interrupts. +- clocks: core clock iHCLK. Optional rate clock iPCLK (default is iHCLK) +- clock-names: Shall be "iHCLK" and "iPCLK" respectively + +Optional Properties: +- socionext,use-rtm: boolean, if required to use "retimed clock" for RX +- socionext,set-aces: boolean, if same active clock edges field to be set. + +Example: + + spi0: spi@ff110000 { + compatible = "socionext,synquacer-spi"; + reg = <0xff110000 0x1000>; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_hsspi>; + clock-names = "iHCLK"; + socionext,use-rtm; + socionext,set-aces; + }; diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt deleted file mode 100644 index 7638b4968ddb..000000000000 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ /dev/null @@ -1,70 +0,0 @@ -ARM PL022 SPI controller - -Required properties: -- compatible : "arm,pl022", "arm,primecell" -- reg : Offset and length of the register set for the device -- interrupts : Should contain SPI controller interrupt -- num-cs : total number of chipselects - -Optional properties: -- cs-gpios : should specify GPIOs used for chipselects. - The gpios will be referred to as reg = <index> in the SPI child nodes. - If unspecified, a single SPI device without a chip select can be used. -- pl022,autosuspend-delay : delay in ms following transfer completion before - the runtime power management system suspends the - device. A setting of 0 indicates no delay and the - device will be suspended immediately -- pl022,rt : indicates the controller should run the message pump with realtime - priority to minimise the transfer latency on the bus (boolean) -- dmas : Two or more DMA channel specifiers following the convention outlined - in bindings/dma/dma.txt -- dma-names: Names for the dma channels, if present. There must be at - least one channel named "tx" for transmit and named "rx" for - receive. - - -SPI slave nodes must be children of the SPI master node and can -contain the following properties. - -- pl022,interface : interface type: - 0: SPI - 1: Texas Instruments Synchronous Serial Frame Format - 2: Microwire (Half Duplex) -- pl022,com-mode : specifies the transfer mode: - 0: interrupt mode - 1: polling mode (default mode if property not present) - 2: DMA mode -- pl022,rx-level-trig : Rx FIFO watermark level -- pl022,tx-level-trig : Tx FIFO watermark level -- pl022,ctrl-len : Microwire interface: Control length -- pl022,wait-state : Microwire interface: Wait state -- pl022,duplex : Microwire interface: Full/Half duplex - - -Example: - - spi@e0100000 { - compatible = "arm,pl022", "arm,primecell"; - reg = <0xe0100000 0x1000>; - #address-cells = <1>; - #size-cells = <0>; - interrupts = <0 31 0x4>; - dmas = <&dma-controller 23 1>, - <&dma-controller 24 0>; - dma-names = "rx", "tx"; - - m25p80@1 { - compatible = "st,m25p80"; - reg = <1>; - spi-max-frequency = <12000000>; - spi-cpol; - spi-cpha; - pl022,interface = <0>; - pl022,com-mode = <0x2>; - pl022,rx-level-trig = <0>; - pl022,tx-level-trig = <0>; - pl022,ctrl-len = <0x11>; - pl022,wait-state = <0>; - pl022,duplex = <0>; - }; - }; diff --git a/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt b/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt new file mode 100644 index 000000000000..d57659996d62 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt @@ -0,0 +1,25 @@ +NXP System Counter Module(sys_ctr) + +The system counter(sys_ctr) is a programmable system counter which provides +a shared time base to Cortex A15, A7, A53, A73, etc. it is intended for use in +applications where the counter is always powered and support multiple, +unrelated clocks. The compare frame inside can be used for timer purpose. + +Required properties: + +- compatible : should be "nxp,sysctr-timer" +- reg : Specifies the base physical address and size of the comapre + frame and the counter control, read & compare. +- interrupts : should be the first compare frames' interrupt +- clocks : Specifies the counter clock. +- clock-names: Specifies the clock's name of this module + +Example: + + system_counter: timer@306a0000 { + compatible = "nxp,sysctr-timer"; + reg = <0x306a0000 0x20000>;/* system-counter-rd & compare */ + clocks = <&clk_8m>; + clock-names = "per"; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml index 747fd3f689dc..2e742d399e87 100644 --- a/Documentation/devicetree/bindings/trivial-devices.yaml +++ b/Documentation/devicetree/bindings/trivial-devices.yaml @@ -52,6 +52,10 @@ properties: - at,24c08 # i2c trusted platform module (TPM) - atmel,at97sc3204t + # i2c h/w symmetric crypto module + - atmel,atsha204a + # i2c h/w elliptic curve crypto module + - atmel,atecc508a # CM32181: Ambient Light Sensor - capella,cm32181 # CM3232: Ambient Light Sensor |
