diff options
Diffstat (limited to 'Documentation/devicetree')
111 files changed, 2638 insertions, 768 deletions
diff --git a/Documentation/devicetree/bindings/Makefile b/Documentation/devicetree/bindings/Makefile index 50daa0b3b032..63b139f9ae28 100644 --- a/Documentation/devicetree/bindings/Makefile +++ b/Documentation/devicetree/bindings/Makefile @@ -15,7 +15,7 @@ DT_TMP_SCHEMA := processed-schema.yaml extra-y += $(DT_TMP_SCHEMA) quiet_cmd_mk_schema = SCHEMA $@ - cmd_mk_schema = $(DT_MK_SCHEMA) $(DT_MK_SCHEMA_FLAGS) -o $@ $(filter-out FORCE, $^) + cmd_mk_schema = $(DT_MK_SCHEMA) $(DT_MK_SCHEMA_FLAGS) -o $@ $(real-prereqs) DT_DOCS = $(shell \ cd $(srctree)/$(src) && \ diff --git a/Documentation/devicetree/bindings/arm/atmel-sysregs.txt b/Documentation/devicetree/bindings/arm/atmel-sysregs.txt index 3363d9ae4e74..e61d00e25b95 100644 --- a/Documentation/devicetree/bindings/arm/atmel-sysregs.txt +++ b/Documentation/devicetree/bindings/arm/atmel-sysregs.txt @@ -21,7 +21,8 @@ Its subnodes can be: RSTC Reset Controller required properties: - compatible: Should be "atmel,<chip>-rstc". - <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3" + <chip> can be "at91sam9260", "at91sam9g45", "sama5d3" or "samx7" + it also can be "microchip,sam9x60-rstc" - reg: Should contain registers location and length - clocks: phandle to input clock. diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.txt b/Documentation/devicetree/bindings/arm/l2c2x0.txt deleted file mode 100644 index fbe6cb21f4cf..000000000000 --- a/Documentation/devicetree/bindings/arm/l2c2x0.txt +++ /dev/null @@ -1,114 +0,0 @@ -* ARM L2 Cache Controller - -ARM cores often have a separate L2C210/L2C220/L2C310 (also known as PL210/PL220/ -PL310 and variants) based level 2 cache controller. All these various implementations -of the L2 cache controller have compatible programming models (Note 1). -Some of the properties that are just prefixed "cache-*" are taken from section -3.7.3 of the Devicetree Specification which can be found at: -https://www.devicetree.org/specifications/ - -The ARM L2 cache representation in the device tree should be done as follows: - -Required properties: - -- compatible : should be one of: - "arm,pl310-cache" - "arm,l220-cache" - "arm,l210-cache" - "bcm,bcm11351-a2-pl310-cache": DEPRECATED by "brcm,bcm11351-a2-pl310-cache" - "brcm,bcm11351-a2-pl310-cache": For Broadcom bcm11351 chipset where an - offset needs to be added to the address before passing down to the L2 - cache controller - "marvell,aurora-system-cache": Marvell Controller designed to be - compatible with the ARM one, with system cache mode (meaning - maintenance operations on L1 are broadcasted to the L2 and L2 - performs the same operation). - "marvell,aurora-outer-cache": Marvell Controller designed to be - compatible with the ARM one with outer cache mode. - "marvell,tauros3-cache": Marvell Tauros3 cache controller, compatible - with arm,pl310-cache controller. -- cache-unified : Specifies the cache is a unified cache. -- cache-level : Should be set to 2 for a level 2 cache. -- reg : Physical base address and size of cache controller's memory mapped - registers. - -Optional properties: - -- arm,data-latency : Cycles of latency for Data RAM accesses. Specifies 3 cells of - read, write and setup latencies. Minimum valid values are 1. Controllers - without setup latency control should use a value of 0. -- arm,tag-latency : Cycles of latency for Tag RAM accesses. Specifies 3 cells of - read, write and setup latencies. Controllers without setup latency control - should use 0. Controllers without separate read and write Tag RAM latency - values should only use the first cell. -- arm,dirty-latency : Cycles of latency for Dirty RAMs. This is a single cell. -- arm,filter-ranges : <start length> Starting address and length of window to - filter. Addresses in the filter window are directed to the M1 port. Other - addresses will go to the M0 port. -- arm,io-coherent : indicates that the system is operating in an hardware - I/O coherent mode. Valid only when the arm,pl310-cache compatible - string is used. -- interrupts : 1 combined interrupt. -- cache-size : specifies the size in bytes of the cache -- cache-sets : specifies the number of associativity sets of the cache -- cache-block-size : specifies the size in bytes of a cache block -- cache-line-size : specifies the size in bytes of a line in the cache, - if this is not specified, the line size is assumed to be equal to the - cache block size -- cache-id-part: cache id part number to be used if it is not present - on hardware -- wt-override: If present then L2 is forced to Write through mode -- arm,double-linefill : Override double linefill enable setting. Enable if - non-zero, disable if zero. -- arm,double-linefill-incr : Override double linefill on INCR read. Enable - if non-zero, disable if zero. -- arm,double-linefill-wrap : Override double linefill on WRAP read. Enable - if non-zero, disable if zero. -- arm,prefetch-drop : Override prefetch drop enable setting. Enable if non-zero, - disable if zero. -- arm,prefetch-offset : Override prefetch offset value. Valid values are - 0-7, 15, 23, and 31. -- arm,shared-override : The default behavior of the L220 or PL310 cache - controllers with respect to the shareable attribute is to transform "normal - memory non-cacheable transactions" into "cacheable no allocate" (for reads) - or "write through no write allocate" (for writes). - On systems where this may cause DMA buffer corruption, this property must be - specified to indicate that such transforms are precluded. -- arm,parity-enable : enable parity checking on the L2 cache (L220 or PL310). -- arm,parity-disable : disable parity checking on the L2 cache (L220 or PL310). -- arm,outer-sync-disable : disable the outer sync operation on the L2 cache. - Some core tiles, especially ARM PB11MPCore have a faulty L220 cache that - will randomly hang unless outer sync operations are disabled. -- prefetch-data : Data prefetch. Value: <0> (forcibly disable), <1> - (forcibly enable), property absent (retain settings set by firmware) -- prefetch-instr : Instruction prefetch. Value: <0> (forcibly disable), - <1> (forcibly enable), property absent (retain settings set by - firmware) -- arm,dynamic-clock-gating : L2 dynamic clock gating. Value: <0> (forcibly - disable), <1> (forcibly enable), property absent (OS specific behavior, - preferably retain firmware settings) -- arm,standby-mode: L2 standby mode enable. Value <0> (forcibly disable), - <1> (forcibly enable), property absent (OS specific behavior, - preferably retain firmware settings) -- arm,early-bresp-disable : Disable the CA9 optimization Early BRESP (PL310) -- arm,full-line-zero-disable : Disable the CA9 optimization Full line of zero - write (PL310) - -Example: - -L2: cache-controller { - compatible = "arm,pl310-cache"; - reg = <0xfff12000 0x1000>; - arm,data-latency = <1 1 1>; - arm,tag-latency = <2 2 2>; - arm,filter-ranges = <0x80000000 0x8000000>; - cache-unified; - cache-level = <2>; - interrupts = <45>; -}; - -Note 1: The description in this document doesn't apply to integrated L2 - cache controllers as found in e.g. Cortex-A15/A7/A57/A53. These - integrated L2 controllers are assumed to be all preconfigured by - early secure boot code. Thus no need to deal with their configuration - in the kernel at all. diff --git a/Documentation/devicetree/bindings/arm/l2c2x0.yaml b/Documentation/devicetree/bindings/arm/l2c2x0.yaml new file mode 100644 index 000000000000..bfc5c185561c --- /dev/null +++ b/Documentation/devicetree/bindings/arm/l2c2x0.yaml @@ -0,0 +1,248 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/l2c2x0.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM L2 Cache Controller + +maintainers: + - Rob Herring <robh@kernel.org> + +description: |+ + ARM cores often have a separate L2C210/L2C220/L2C310 (also known as PL210/ + PL220/PL310 and variants) based level 2 cache controller. All these various + implementations of the L2 cache controller have compatible programming + models (Note 1). Some of the properties that are just prefixed "cache-*" are + taken from section 3.7.3 of the Devicetree Specification which can be found + at: + https://www.devicetree.org/specifications/ + + Note 1: The description in this document doesn't apply to integrated L2 + cache controllers as found in e.g. Cortex-A15/A7/A57/A53. These + integrated L2 controllers are assumed to be all preconfigured by + early secure boot code. Thus no need to deal with their configuration + in the kernel at all. + +allOf: + - $ref: /schemas/cache-controller.yaml# + +properties: + compatible: + enum: + - arm,pl310-cache + - arm,l220-cache + - arm,l210-cache + # DEPRECATED by "brcm,bcm11351-a2-pl310-cache" + - bcm,bcm11351-a2-pl310-cache + # For Broadcom bcm11351 chipset where an + # offset needs to be added to the address before passing down to the L2 + # cache controller + - brcm,bcm11351-a2-pl310-cache + # Marvell Controller designed to be + # compatible with the ARM one, with system cache mode (meaning + # maintenance operations on L1 are broadcasted to the L2 and L2 + # performs the same operation). + - marvell,aurora-system-cache + # Marvell Controller designed to be + # compatible with the ARM one with outer cache mode. + - marvell,aurora-outer-cache + # Marvell Tauros3 cache controller, compatible + # with arm,pl310-cache controller. + - marvell,tauros3-cache + + cache-level: + const: 2 + + cache-unified: true + cache-size: true + cache-sets: true + cache-block-size: true + cache-line-size: true + + reg: + maxItems: 1 + + arm,data-latency: + description: Cycles of latency for Data RAM accesses. Specifies 3 cells of + read, write and setup latencies. Minimum valid values are 1. Controllers + without setup latency control should use a value of 0. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - minItems: 2 + maxItems: 3 + items: + minimum: 0 + maximum: 8 + + arm,tag-latency: + description: Cycles of latency for Tag RAM accesses. Specifies 3 cells of + read, write and setup latencies. Controllers without setup latency control + should use 0. Controllers without separate read and write Tag RAM latency + values should only use the first cell. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - minItems: 1 + maxItems: 3 + items: + minimum: 0 + maximum: 8 + + arm,dirty-latency: + description: Cycles of latency for Dirty RAMs. This is a single cell. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 1 + maximum: 8 + + arm,filter-ranges: + description: <start length> Starting address and length of window to + filter. Addresses in the filter window are directed to the M1 port. Other + addresses will go to the M0 port. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - items: + minItems: 2 + maxItems: 2 + + arm,io-coherent: + description: indicates that the system is operating in an hardware + I/O coherent mode. Valid only when the arm,pl310-cache compatible + string is used. + type: boolean + + interrupts: + # Either a single combined interrupt or up to 9 individual interrupts + minItems: 1 + maxItems: 9 + + cache-id-part: + description: cache id part number to be used if it is not present + on hardware + $ref: /schemas/types.yaml#/definitions/uint32 + + wt-override: + description: If present then L2 is forced to Write through mode + type: boolean + + arm,double-linefill: + description: Override double linefill enable setting. Enable if + non-zero, disable if zero. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + + arm,double-linefill-incr: + description: Override double linefill on INCR read. Enable + if non-zero, disable if zero. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + + arm,double-linefill-wrap: + description: Override double linefill on WRAP read. Enable + if non-zero, disable if zero. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + + arm,prefetch-drop: + description: Override prefetch drop enable setting. Enable if non-zero, + disable if zero. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + + arm,prefetch-offset: + description: Override prefetch offset value. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1, 2, 3, 4, 5, 6, 7, 15, 23, 31 ] + + arm,shared-override: + description: The default behavior of the L220 or PL310 cache + controllers with respect to the shareable attribute is to transform "normal + memory non-cacheable transactions" into "cacheable no allocate" (for reads) + or "write through no write allocate" (for writes). + On systems where this may cause DMA buffer corruption, this property must + be specified to indicate that such transforms are precluded. + type: boolean + + arm,parity-enable: + description: enable parity checking on the L2 cache (L220 or PL310). + type: boolean + + arm,parity-disable: + description: disable parity checking on the L2 cache (L220 or PL310). + type: boolean + + arm,outer-sync-disable: + description: disable the outer sync operation on the L2 cache. + Some core tiles, especially ARM PB11MPCore have a faulty L220 cache that + will randomly hang unless outer sync operations are disabled. + type: boolean + + prefetch-data: + description: | + Data prefetch. Value: <0> (forcibly disable), <1> + (forcibly enable), property absent (retain settings set by firmware) + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + + prefetch-instr: + description: | + Instruction prefetch. Value: <0> (forcibly disable), + <1> (forcibly enable), property absent (retain settings set by + firmware) + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + + arm,dynamic-clock-gating: + description: | + L2 dynamic clock gating. Value: <0> (forcibly + disable), <1> (forcibly enable), property absent (OS specific behavior, + preferably retain firmware settings) + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + + arm,standby-mode: + description: L2 standby mode enable. Value <0> (forcibly disable), + <1> (forcibly enable), property absent (OS specific behavior, + preferably retain firmware settings) + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + + arm,early-bresp-disable: + description: Disable the CA9 optimization Early BRESP (PL310) + type: boolean + + arm,full-line-zero-disable: + description: Disable the CA9 optimization Full line of zero + write (PL310) + type: boolean + +required: + - compatible + - cache-unified + - reg + +additionalProperties: false + +examples: + - | + cache-controller@fff12000 { + compatible = "arm,pl310-cache"; + reg = <0xfff12000 0x1000>; + arm,data-latency = <1 1 1>; + arm,tag-latency = <2 2 2>; + arm,filter-ranges = <0x80000000 0x8000000>; + cache-unified; + cache-level = <2>; + interrupts = <45>; + }; + +... diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt deleted file mode 100644 index 13611a8199bb..000000000000 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ /dev/null @@ -1,70 +0,0 @@ -* ARM Performance Monitor Units - -ARM cores often have a PMU for counting cpu and cache events like cache misses -and hits. The interface to the PMU is part of the ARM ARM. The ARM PMU -representation in the device tree should be done as under:- - -Required properties: - -- compatible : should be one of - "apm,potenza-pmu" - "arm,armv8-pmuv3" - "arm,cortex-a73-pmu" - "arm,cortex-a72-pmu" - "arm,cortex-a57-pmu" - "arm,cortex-a53-pmu" - "arm,cortex-a35-pmu" - "arm,cortex-a17-pmu" - "arm,cortex-a15-pmu" - "arm,cortex-a12-pmu" - "arm,cortex-a9-pmu" - "arm,cortex-a8-pmu" - "arm,cortex-a7-pmu" - "arm,cortex-a5-pmu" - "arm,arm11mpcore-pmu" - "arm,arm1176-pmu" - "arm,arm1136-pmu" - "brcm,vulcan-pmu" - "cavium,thunder-pmu" - "qcom,scorpion-pmu" - "qcom,scorpion-mp-pmu" - "qcom,krait-pmu" -- interrupts : 1 combined interrupt or 1 per core. If the interrupt is a per-cpu - interrupt (PPI) then 1 interrupt should be specified. - -Optional properties: - -- interrupt-affinity : When using SPIs, specifies a list of phandles to CPU - nodes corresponding directly to the affinity of - the SPIs listed in the interrupts property. - - When using a PPI, specifies a list of phandles to CPU - nodes corresponding to the set of CPUs which have - a PMU of this type signalling the PPI listed in the - interrupts property, unless this is already specified - by the PPI interrupt specifier itself (in which case - the interrupt-affinity property shouldn't be present). - - This property should be present when there is more than - a single SPI. - - -- qcom,no-pc-write : Indicates that this PMU doesn't support the 0xc and 0xd - events. - -- secure-reg-access : Indicates that the ARMv7 Secure Debug Enable Register - (SDER) is accessible. This will cause the driver to do - any setup required that is only possible in ARMv7 secure - state. If not present the ARMv7 SDER will not be touched, - which means the PMU may fail to operate unless external - code (bootloader or security monitor) has performed the - appropriate initialisation. Note that this property is - not valid for non-ARMv7 CPUs or ARMv7 CPUs booting Linux - in Non-secure state. - -Example: - -pmu { - compatible = "arm,cortex-a9-pmu"; - interrupts = <100 101>; -}; diff --git a/Documentation/devicetree/bindings/arm/pmu.yaml b/Documentation/devicetree/bindings/arm/pmu.yaml new file mode 100644 index 000000000000..52ae094ce330 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/pmu.yaml @@ -0,0 +1,87 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/arm/pmu.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Performance Monitor Units + +maintainers: + - Mark Rutland <mark.rutland@arm.com> + - Will Deacon <will.deacon@arm.com> + +description: |+ + ARM cores often have a PMU for counting cpu and cache events like cache misses + and hits. The interface to the PMU is part of the ARM ARM. The ARM PMU + representation in the device tree should be done as under:- + +properties: + compatible: + items: + - enum: + - apm,potenza-pmu + - arm,armv8-pmuv3 + - arm,cortex-a73-pmu + - arm,cortex-a72-pmu + - arm,cortex-a57-pmu + - arm,cortex-a53-pmu + - arm,cortex-a35-pmu + - arm,cortex-a17-pmu + - arm,cortex-a15-pmu + - arm,cortex-a12-pmu + - arm,cortex-a9-pmu + - arm,cortex-a8-pmu + - arm,cortex-a7-pmu + - arm,cortex-a5-pmu + - arm,arm11mpcore-pmu + - arm,arm1176-pmu + - arm,arm1136-pmu + - brcm,vulcan-pmu + - cavium,thunder-pmu + - qcom,scorpion-pmu + - qcom,scorpion-mp-pmu + - qcom,krait-pmu + + interrupts: + # Don't know how many CPUs, so no constraints to specify + description: 1 per-cpu interrupt (PPI) or 1 interrupt per core. + + interrupt-affinity: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + When using SPIs, specifies a list of phandles to CPU + nodes corresponding directly to the affinity of + the SPIs listed in the interrupts property. + + When using a PPI, specifies a list of phandles to CPU + nodes corresponding to the set of CPUs which have + a PMU of this type signalling the PPI listed in the + interrupts property, unless this is already specified + by the PPI interrupt specifier itself (in which case + the interrupt-affinity property shouldn't be present). + + This property should be present when there is more than + a single SPI. + + qcom,no-pc-write: + type: boolean + description: + Indicates that this PMU doesn't support the 0xc and 0xd events. + + secure-reg-access: + type: boolean + description: + Indicates that the ARMv7 Secure Debug Enable Register + (SDER) is accessible. This will cause the driver to do + any setup required that is only possible in ARMv7 secure + state. If not present the ARMv7 SDER will not be touched, + which means the PMU may fail to operate unless external + code (bootloader or security monitor) has performed the + appropriate initialisation. Note that this property is + not valid for non-ARMv7 CPUs or ARMv7 CPUs booting Linux + in Non-secure state. + +required: + - compatible + +... diff --git a/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt b/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt index 2ef86ae96df8..d19885b7c73f 100644 --- a/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt +++ b/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt @@ -2,13 +2,14 @@ The Actions Semi Owl Clock Management Unit generates and supplies clock to various controllers within the SoC. The clock binding described here is -applicable to S900 and S700 SoC's. +applicable to S900, S700 and S500 SoC's. Required Properties: - compatible: should be one of the following, "actions,s900-cmu" "actions,s700-cmu" + "actions,s500-cmu" - reg: physical base address of the controller and length of memory mapped region. - clocks: Reference to the parent clocks ("hosc", "losc") @@ -19,8 +20,8 @@ Each clock is assigned an identifier, and client nodes can use this identifier to specify the clock which they consume. All available clocks are defined as preprocessor macros in corresponding -dt-bindings/clock/actions,s900-cmu.h or actions,s700-cmu.h header and can be -used in device tree sources. +dt-bindings/clock/actions,s900-cmu.h or actions,s700-cmu.h or +actions,s500-cmu.h header and can be used in device tree sources. External clocks: diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt index 79511d7bb321..c41f0be5d438 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -10,6 +10,7 @@ Required Properties: - GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc" - GXM (S912) : "amlogic,meson-gxm-aoclkc" - AXG (A113D, A113X) : "amlogic,meson-axg-aoclkc" + - G12A (S905X2, S905D2, S905Y2) : "amlogic,meson-g12a-aoclkc" followed by the common "amlogic,meson-gx-aoclkc" - clocks: list of clock phandle, one for each entry clock-names. - clock-names: should contain the following: diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt index a6871953bf04..5c8b105be4d6 100644 --- a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -9,6 +9,7 @@ Required Properties: "amlogic,gxbb-clkc" for GXBB SoC, "amlogic,gxl-clkc" for GXL and GXM SoC, "amlogic,axg-clkc" for AXG SoC. + "amlogic,g12a-clkc" for G12A SoC. - clocks : list of clock phandle, one for each entry clock-names. - clock-names : should contain the following: * "xtal": the platform xtal diff --git a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt index 50d5897c9849..183c327a7d6b 100644 --- a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt @@ -50,6 +50,8 @@ Required Properties: IPs. - "samsung,exynos5433-cmu-cam1" - clock controller compatible for CMU_CAM1 which generates clocks for Cortex-A5/MIPI_CSIS2/FIMC-LITE_C/FIMC-FD IPs. + - "samsung,exynos5433-cmu-imem" - clock controller compatible for CMU_IMEM + which generates clocks for SSS (Security SubSystem) and SlimSSS IPs. - reg: physical base address of the controller and length of memory mapped region. @@ -168,6 +170,12 @@ Required Properties: - aclk_cam1_400 - aclk_cam1_552 + Input clocks for imem clock controller: + - oscclk + - aclk_imem_sssx_266 + - aclk_imem_266 + - aclk_imem_200 + Optional properties: - power-domains: a phandle to respective power domain node as described by generic PM domain bindings (see power/power_domain.txt for more @@ -469,6 +477,21 @@ Example 2: Examples of clock controller nodes are listed below. power-domains = <&pd_cam1>; }; + cmu_imem: clock-controller@11060000 { + compatible = "samsung,exynos5433-cmu-imem"; + reg = <0x11060000 0x1000>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_imem_sssx_266", + "aclk_imem_266", + "aclk_imem_200"; + clocks = <&xxti>, + <&cmu_top CLK_DIV_ACLK_IMEM_SSSX_266>, + <&cmu_top CLK_DIV_ACLK_IMEM_266>, + <&cmu_top CLK_DIV_ACLK_IMEM_200>; + }; + Example 3: UART controller node that consumes the clock generated by the clock controller. diff --git a/Documentation/devicetree/bindings/clock/fixed-clock.txt b/Documentation/devicetree/bindings/clock/fixed-clock.txt deleted file mode 100644 index 0641a663ad69..000000000000 --- a/Documentation/devicetree/bindings/clock/fixed-clock.txt +++ /dev/null @@ -1,23 +0,0 @@ -Binding for simple fixed-rate clock sources. - -This binding uses the common clock binding[1]. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt - -Required properties: -- compatible : shall be "fixed-clock". -- #clock-cells : from common clock binding; shall be set to 0. -- clock-frequency : frequency of clock in Hz. Should be a single cell. - -Optional properties: -- clock-accuracy : accuracy of clock in ppb (parts per billion). - Should be a single cell. -- clock-output-names : From common clock binding. - -Example: - clock { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <1000000000>; - clock-accuracy = <100>; - }; diff --git a/Documentation/devicetree/bindings/clock/fixed-clock.yaml b/Documentation/devicetree/bindings/clock/fixed-clock.yaml new file mode 100644 index 000000000000..b657ecd0ef1c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fixed-clock.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/fixed-clock.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for simple fixed-rate clock sources + +maintainers: + - Michael Turquette <mturquette@baylibre.com> + - Stephen Boyd <sboyd@kernel.org> + +properties: + compatible: + const: fixed-clock + + "#clock-cells": + const: 0 + + clock-frequency: true + + clock-accuracy: + description: accuracy of clock in ppb (parts per billion). + $ref: /schemas/types.yaml#/definitions/uint32 + + clock-output-names: + maxItems: 1 + +required: + - compatible + - "#clock-cells" + - clock-frequency + +additionalProperties: false + +examples: + - | + clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000000>; + clock-accuracy = <100>; + }; +... diff --git a/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt deleted file mode 100644 index 189467a7188a..000000000000 --- a/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt +++ /dev/null @@ -1,28 +0,0 @@ -Binding for simple fixed factor rate clock sources. - -This binding uses the common clock binding[1]. - -[1] Documentation/devicetree/bindings/clock/clock-bindings.txt - -Required properties: -- compatible : shall be "fixed-factor-clock". -- #clock-cells : from common clock binding; shall be set to 0. -- clock-div: fixed divider. -- clock-mult: fixed multiplier. -- clocks: parent clock. - -Optional properties: -- clock-output-names : From common clock binding. - -Some clocks that require special treatments are also handled by that -driver, with the compatibles: - - allwinner,sun4i-a10-pll3-2x-clk - -Example: - clock { - compatible = "fixed-factor-clock"; - clocks = <&parentclk>; - #clock-cells = <0>; - clock-div = <2>; - clock-mult = <1>; - }; diff --git a/Documentation/devicetree/bindings/clock/fixed-factor-clock.yaml b/Documentation/devicetree/bindings/clock/fixed-factor-clock.yaml new file mode 100644 index 000000000000..b567f8092f8c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fixed-factor-clock.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/fixed-factor-clock.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for simple fixed factor rate clock sources + +maintainers: + - Michael Turquette <mturquette@baylibre.com> + - Stephen Boyd <sboyd@kernel.org> + +properties: + compatible: + enum: + - allwinner,sun4i-a10-pll3-2x-clk + - fixed-factor-clock + + "#clock-cells": + const: 0 + + clocks: + maxItems: 1 + + clock-div: + description: Fixed divider + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 1 + + clock-mult: + description: Fixed multiplier + $ref: /schemas/types.yaml#/definitions/uint32 + + clock-output-names: + maxItems: 1 + +required: + - compatible + - clocks + - "#clock-cells" + - clock-div + - clock-mult + +additionalProperties: false + +examples: + - | + clock { + compatible = "fixed-factor-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + clock-div = <2>; + clock-mult = <1>; + }; +... diff --git a/Documentation/devicetree/bindings/clock/fixed-mmio-clock.txt b/Documentation/devicetree/bindings/clock/fixed-mmio-clock.txt new file mode 100644 index 000000000000..c359367fd1a9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fixed-mmio-clock.txt @@ -0,0 +1,24 @@ +Binding for simple memory mapped io fixed-rate clock sources. +The driver reads a clock frequency value from a single 32-bit memory mapped +I/O register and registers it as a fixed rate clock. + +It was designed for test systems, like FPGA, not for complete, finished SoCs. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "fixed-mmio-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- reg : Address and length of the clock value register set. + +Optional properties: +- clock-output-names : From common clock binding. + +Example: +sysclock: sysclock@fd020004 { + #clock-cells = <0>; + compatible = "fixed-mmio-clock"; + reg = <0xfd020004 0x4>; +}; diff --git a/Documentation/devicetree/bindings/clock/imx8mm-clock.txt b/Documentation/devicetree/bindings/clock/imx8mm-clock.txt new file mode 100644 index 000000000000..8e4ab9e619a1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx8mm-clock.txt @@ -0,0 +1,29 @@ +* Clock bindings for NXP i.MX8M Mini + +Required properties: +- compatible: Should be "fsl,imx8mm-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include the following entries: + - "osc_32k" + - "osc_24m" + - "clk_ext1" + - "clk_ext2" + - "clk_ext3" + - "clk_ext4" + +clk: clock-controller@30380000 { + compatible = "fsl,imx8mm-ccm"; + reg = <0x0 0x30380000 0x0 0x10000>; + #clock-cells = <1>; + clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>, <&clk_ext2>, + <&clk_ext3>, <&clk_ext4>; + clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2", + "clk_ext3", "clk_ext4"; +}; + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx8mm-clock.h +for the full list of i.MX8M Mini clock IDs. diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt index 87b4949e9bc8..944719bd586f 100644 --- a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt +++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt @@ -16,6 +16,7 @@ Required properties : "qcom,rpmcc-msm8974", "qcom,rpmcc" "qcom,rpmcc-apq8064", "qcom,rpmcc" "qcom,rpmcc-msm8996", "qcom,rpmcc" + "qcom,rpmcc-msm8998", "qcom,rpmcc" "qcom,rpmcc-qcs404", "qcom,rpmcc" - #clock-cells : shall contain 1 diff --git a/Documentation/devicetree/bindings/display/sitronix,st7735r.txt b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt index f0a5090a3326..cd5c7186890a 100644 --- a/Documentation/devicetree/bindings/display/sitronix,st7735r.txt +++ b/Documentation/devicetree/bindings/display/sitronix,st7735r.txt @@ -20,7 +20,7 @@ Example: backlight: backlight { compatible = "gpio-backlight"; gpios = <&gpio 44 GPIO_ACTIVE_HIGH>; - } + }; ... diff --git a/Documentation/devicetree/bindings/display/ssd1307fb.txt b/Documentation/devicetree/bindings/display/ssd1307fb.txt index 209d931ef16c..b67f8caa212c 100644 --- a/Documentation/devicetree/bindings/display/ssd1307fb.txt +++ b/Documentation/devicetree/bindings/display/ssd1307fb.txt @@ -36,7 +36,6 @@ ssd1307: oled@3c { reg = <0x3c>; pwms = <&pwm 4 3000>; reset-gpios = <&gpio2 7>; - reset-active-low; }; ssd1306: oled@3c { @@ -44,7 +43,6 @@ ssd1306: oled@3c { reg = <0x3c>; pwms = <&pwm 4 3000>; reset-gpios = <&gpio2 7>; - reset-active-low; solomon,com-lrremap; solomon,com-invdir; solomon,com-offset = <32>; diff --git a/Documentation/devicetree/bindings/dma/dma.txt b/Documentation/devicetree/bindings/dma/dma.txt index 6312fb00ce8d..eeb4e4d1771e 100644 --- a/Documentation/devicetree/bindings/dma/dma.txt +++ b/Documentation/devicetree/bindings/dma/dma.txt @@ -16,6 +16,9 @@ Optional properties: - dma-channels: Number of DMA channels supported by the controller. - dma-requests: Number of DMA request signals supported by the controller. +- dma-channel-mask: Bitmask of available DMA channels in ascending order + that are not reserved by firmware and are available to + the kernel. i.e. first channel corresponds to LSB. Example: @@ -29,6 +32,7 @@ Example: #dma-cells = <1>; dma-channels = <32>; dma-requests = <127>; + dma-channel-mask = <0xfffe> }; * DMA router diff --git a/Documentation/devicetree/bindings/dma/fsl-qdma.txt b/Documentation/devicetree/bindings/dma/fsl-qdma.txt new file mode 100644 index 000000000000..6a0ff9059e72 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/fsl-qdma.txt @@ -0,0 +1,57 @@ +NXP Layerscape SoC qDMA Controller +================================== + +This device follows the generic DMA bindings defined in dma/dma.txt. + +Required properties: + +- compatible: Must be one of + "fsl,ls1021a-qdma": for LS1021A Board + "fsl,ls1043a-qdma": for ls1043A Board + "fsl,ls1046a-qdma": for ls1046A Board +- reg: Should contain the register's base address and length. +- interrupts: Should contain a reference to the interrupt used by this + device. +- interrupt-names: Should contain interrupt names: + "qdma-queue0": the block0 interrupt + "qdma-queue1": the block1 interrupt + "qdma-queue2": the block2 interrupt + "qdma-queue3": the block3 interrupt + "qdma-error": the error interrupt +- fsl,dma-queues: Should contain number of queues supported. +- dma-channels: Number of DMA channels supported +- block-number: the virtual block number +- block-offset: the offset of different virtual block +- status-sizes: status queue size of per virtual block +- queue-sizes: command queue size of per virtual block, the size number + based on queues + +Optional properties: + +- dma-channels: Number of DMA channels supported by the controller. +- big-endian: If present registers and hardware scatter/gather descriptors + of the qDMA are implemented in big endian mode, otherwise in little + mode. + +Examples: + + qdma: dma-controller@8390000 { + compatible = "fsl,ls1021a-qdma"; + reg = <0x0 0x8388000 0x0 0x1000>, /* Controller regs */ + <0x0 0x8389000 0x0 0x1000>, /* Status regs */ + <0x0 0x838a000 0x0 0x2000>; /* Block regs */ + interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "qdma-error", + "qdma-queue0", "qdma-queue1"; + dma-channels = <8>; + block-number = <2>; + block-offset = <0x1000>; + fsl,dma-queues = <2>; + status-sizes = <64>; + queue-sizes = <64 64>; + big-endian; + }; + +DMA clients must use the format described in dma/dma.txt file. diff --git a/Documentation/devicetree/bindings/dma/k3dma.txt b/Documentation/devicetree/bindings/dma/k3dma.txt index 4945aeac4dc4..10a2f15b08a3 100644 --- a/Documentation/devicetree/bindings/dma/k3dma.txt +++ b/Documentation/devicetree/bindings/dma/k3dma.txt @@ -3,7 +3,9 @@ See dma.txt first Required properties: -- compatible: Should be "hisilicon,k3-dma-1.0" +- compatible: Must be one of +- "hisilicon,k3-dma-1.0" +- "hisilicon,hisi-pcm-asp-dma-1.0" - reg: Should contain DMA registers location and length. - interrupts: Should contain one interrupt shared by all channel - #dma-cells: see dma.txt, should be 1, para number diff --git a/Documentation/devicetree/bindings/dma/snps-dma.txt b/Documentation/devicetree/bindings/dma/snps-dma.txt index db757df7057d..0bedceed1963 100644 --- a/Documentation/devicetree/bindings/dma/snps-dma.txt +++ b/Documentation/devicetree/bindings/dma/snps-dma.txt @@ -23,8 +23,6 @@ Deprecated properties: Optional properties: -- is_private: The device channels should be marked as private and not for by the - general purpose DMA channel allocator. False if not passed. - multi-block: Multi block transfers supported by hardware. Array property with one cell per channel. 0: not supported, 1 (default): supported. - snps,dma-protection-control: AHB HPROT[3:1] protection setting. diff --git a/Documentation/devicetree/bindings/dma/sprd-dma.txt b/Documentation/devicetree/bindings/dma/sprd-dma.txt index 7a10fea2e51b..adccea9941f1 100644 --- a/Documentation/devicetree/bindings/dma/sprd-dma.txt +++ b/Documentation/devicetree/bindings/dma/sprd-dma.txt @@ -31,7 +31,7 @@ DMA clients connected to the Spreadtrum DMA controller must use the format described in the dma.txt file, using a two-cell specifier for each channel. The two cells in order are: 1. A phandle pointing to the DMA controller. -2. The channel id. +2. The slave id. spi0: spi@70a00000{ ... diff --git a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt index 174af2c45e77..93b6d961dd4f 100644 --- a/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt +++ b/Documentation/devicetree/bindings/dma/xilinx/xilinx_dma.txt @@ -37,10 +37,11 @@ Required properties: Required properties for VDMA: - xlnx,num-fstores: Should be the number of framebuffers as configured in h/w. -Optional properties: -- xlnx,include-sg: Tells configured for Scatter-mode in - the hardware. Optional properties for AXI DMA: +- xlnx,sg-length-width: Should be set to the width in bits of the length + register as configured in h/w. Takes values {8...26}. If the property + is missing or invalid then the default value 23 is used. This is the + maximum value that is supported by all IP versions. - xlnx,mcdma: Tells whether configured for multi-channel mode in the hardware. Optional properties for VDMA: - xlnx,flush-fsync: Tells which channel to Flush on Frame sync. diff --git a/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt new file mode 100644 index 000000000000..6a0f3d90d682 --- /dev/null +++ b/Documentation/devicetree/bindings/edac/aspeed-sdram-edac.txt @@ -0,0 +1,25 @@ +Aspeed AST2500 SoC EDAC node + +The Aspeed AST2500 SoC supports DDR3 and DDR4 memory with and without ECC (error +correction check). + +The memory controller supports SECDED (single bit error correction, double bit +error detection) and single bit error auto scrubbing by reserving 8 bits for +every 64 bit word (effectively reducing available memory to 8/9). + +Note, the bootloader must configure ECC mode in the memory controller. + + +Required properties: +- compatible: should be "aspeed,ast2500-sdram-edac" +- reg: sdram controller register set should be <0x1e6e0000 0x174> +- interrupts: should be AVIC interrupt #0 + + +Example: + + edac: sdram@1e6e0000 { + compatible = "aspeed,ast2500-sdram-edac"; + reg = <0x1e6e0000 0x174>; + interrupts = <0>; + }; diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt index f9a7c984274c..0e456bbc1213 100644 --- a/Documentation/devicetree/bindings/eeprom/at24.txt +++ b/Documentation/devicetree/bindings/eeprom/at24.txt @@ -75,6 +75,8 @@ Optional properties: - address-width: number of address bits (one of 8, 16). + - num-addresses: total number of i2c slave addresses this device takes + Example: eeprom@52 { @@ -82,4 +84,5 @@ eeprom@52 { reg = <0x52>; pagesize = <32>; wp-gpios = <&gpio1 3 0>; + num-addresses = <8>; }; diff --git a/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt new file mode 100644 index 000000000000..6e81f8b755c5 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gateworks,pld-gpio.txt @@ -0,0 +1,20 @@ +Gateworks PLD GPIO controller bindings + +The GPIO controller should be a child node on an I2C bus, +see: i2c/i2c.txt for details. + +Required properties: +- compatible: Should be "gateworks,pld-gpio" +- reg: I2C slave address +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Should be <2>. The first cell is the gpio number and + the second cell is used to specify optional parameters. + +Example: + +pld@56 { + compatible = "gateworks,pld-gpio"; + reg = <0x56>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt index 93d98d09d92b..54040a2bfe3a 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-eic-sprd.txt @@ -33,7 +33,7 @@ Required properties: "sprd,sc9860-eic-latch", "sprd,sc9860-eic-async", "sprd,sc9860-eic-sync", - "sprd,sc27xx-eic". + "sprd,sc2731-eic". - reg: Define the base and range of the I/O address space containing the GPIO controller registers. - gpio-controller: Marks the device node as a GPIO controller. @@ -86,7 +86,7 @@ Example: }; pmic_eic: gpio@300 { - compatible = "sprd,sc27xx-eic"; + compatible = "sprd,sc2731-eic"; reg = <0x300>; interrupt-parent = <&sc2731_pmic>; interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt index 4e3c550e319a..fb144e2b6522 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-pca953x.txt @@ -16,6 +16,7 @@ Required properties: nxp,pca9574 nxp,pca9575 nxp,pca9698 + nxp,pcal6416 nxp,pcal6524 nxp,pcal9555a maxim,max7310 diff --git a/Documentation/devicetree/bindings/gpio/gpio.txt b/Documentation/devicetree/bindings/gpio/gpio.txt index f0ba154b5723..a8895d339bfe 100644 --- a/Documentation/devicetree/bindings/gpio/gpio.txt +++ b/Documentation/devicetree/bindings/gpio/gpio.txt @@ -67,6 +67,18 @@ Optional standard bitfield specifiers for the last cell: https://en.wikipedia.org/wiki/Open_collector - Bit 3: 0 means the output should be maintained during sleep/low-power mode 1 means the output state can be lost during sleep/low-power mode +- Bit 4: 0 means no pull-up resistor should be enabled + 1 means a pull-up resistor should be enabled + This setting only applies to hardware with a simple on/off + control for pull-up configuration. If the hardware has more + elaborate pull-up configuration, it should be represented + using a pin control binding. +- Bit 5: 0 means no pull-down resistor should be enabled + 1 means a pull-down resistor should be enabled + This setting only applies to hardware with a simple on/off + control for pull-down configuration. If the hardware has more + elaborate pull-down configuration, it should be represented + using a pin control binding. 1.1) GPIO specifier best practices ---------------------------------- diff --git a/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt b/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt new file mode 100644 index 000000000000..8dc41ed99685 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/intel,ixp4xx-gpio.txt @@ -0,0 +1,38 @@ +Intel IXP4xx XScale Networking Processors GPIO + +This GPIO controller is found in the Intel IXP4xx processors. +It supports 16 GPIO lines. + +The interrupt portions of the GPIO controller is hierarchical: +the synchronous edge detector is part of the GPIO block, but the +actual enabling/disabling of the interrupt line is done in the +main IXP4xx interrupt controller which has a 1:1 mapping for +the first 12 GPIO lines to 12 system interrupts. + +The remaining 4 GPIO lines can not be used for receiving +interrupts. + +The interrupt parent of this GPIO controller must be the +IXP4xx interrupt controller. + +Required properties: + +- compatible : Should be + "intel,ixp4xx-gpio" +- reg : Should contain registers location and length +- gpio-controller : marks this as a GPIO controller +- #gpio-cells : Should be 2, see gpio/gpio.txt +- interrupt-controller : marks this as an interrupt controller +- #interrupt-cells : a standard two-cell interrupt, see + interrupt-controller/interrupts.txt + +Example: + +gpio0: gpio@c8004000 { + compatible = "intel,ixp4xx-gpio"; + reg = <0xc8004000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/hwmon/adc128d818.txt b/Documentation/devicetree/bindings/hwmon/adc128d818.txt index 08bab0e94d25..d0ae46d7bac3 100644 --- a/Documentation/devicetree/bindings/hwmon/adc128d818.txt +++ b/Documentation/devicetree/bindings/hwmon/adc128d818.txt @@ -26,7 +26,7 @@ Required node properties: Optional node properties: - - ti,mode: Operation mode (see above). + - ti,mode: Operation mode (u8) (see above). Example (operation mode 2): @@ -34,5 +34,5 @@ Example (operation mode 2): adc128d818@1d { compatible = "ti,adc128d818"; reg = <0x1d>; - ti,mode = <2>; + ti,mode = /bits/ 8 <2>; }; diff --git a/Documentation/devicetree/bindings/i2c/i2c-iop3xx.txt b/Documentation/devicetree/bindings/i2c/i2c-iop3xx.txt new file mode 100644 index 000000000000..dcc8390e0d24 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/i2c-iop3xx.txt @@ -0,0 +1,20 @@ +i2c Controller on XScale platforms such as IOP3xx and IXP4xx + +Required properties: +- compatible : Must be one of + "intel,iop3xx-i2c" + "intel,ixp4xx-i2c"; +- reg +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- Child nodes conforming to i2c bus binding + +Example: + +i2c@c8011000 { + compatible = "intel,ixp4xx-i2c"; + reg = <0xc8011000 0x18>; + interrupts = <33 IRQ_TYPE_LEVEL_LOW>; +}; diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt index e199695b1c96..ee4c32454198 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-mt65xx.txt @@ -10,6 +10,7 @@ Required properties: "mediatek,mt6589-i2c": for MediaTek MT6589 "mediatek,mt7622-i2c": for MediaTek MT7622 "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623 + "mediatek,mt7629-i2c", "mediatek,mt2712-i2c": for MediaTek MT7629 "mediatek,mt8173-i2c": for MediaTek MT8173 - reg: physical base address of the controller and dma base, length of memory mapped region. diff --git a/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt b/Documentation/devicetree/bindings/i2c/i2c-stu300.txt index bd81a482634f..bd81a482634f 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-stu300.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sun6i-p2wi.txt index 49df0053347a..49df0053347a 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-sun6i-p2wi.txt diff --git a/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt b/Documentation/devicetree/bindings/i2c/i2c-wmt.txt index 94a425eaa6c7..94a425eaa6c7 100644 --- a/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt +++ b/Documentation/devicetree/bindings/i2c/i2c-wmt.txt diff --git a/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt new file mode 100644 index 000000000000..480e66422625 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/stmpe-adc.txt @@ -0,0 +1,21 @@ +STMPE ADC driver +---------------- + +Required properties: + - compatible: "st,stmpe-adc" + +Optional properties: +Note that the ADC is shared with the STMPE touchscreen. ADC related settings +have to be done in the mfd. +- st,norequest-mask: bitmask specifying which ADC channels should _not_ be + requestable due to different usage (e.g. touch) + +Node name must be stmpe_adc and should be child node of stmpe node to +which it belongs. + +Example: + + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; /* dont use ADC CH3-0 */ + }; diff --git a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt index 0c252d9306da..ef2ae729718f 100644 --- a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt +++ b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt @@ -1,13 +1,19 @@ Samsung tm2-touchkey Required properties: -- compatible: must be "cypress,tm2-touchkey" +- compatible: + * "cypress,tm2-touchkey" - for the touchkey found on the tm2 board + * "cypress,midas-touchkey" - for the touchkey found on midas boards + * "cypress,aries-touchkey" - for the touchkey found on aries boards - reg: I2C address of the chip. - interrupts: interrupt to which the chip is connected (see interrupt binding[0]). - vcc-supply : internal regulator output. 1.8V - vdd-supply : power supply for IC 3.3V +Optional properties: +- linux,keycodes: array of keycodes (max 4), default KEY_PHONE and KEY_BACK + [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt Example: @@ -21,5 +27,6 @@ Example: interrupts = <2 IRQ_TYPE_EDGE_FALLING>; vcc-supply=<&ldo32_reg>; vdd-supply=<&ldo33_reg>; + linux,keycodes = <KEY_PHONE KEY_BACK>; }; }; diff --git a/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt b/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt new file mode 100644 index 000000000000..b2a76301e632 --- /dev/null +++ b/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt @@ -0,0 +1,25 @@ +Ilitek ILI210x/ILI251x touchscreen controller + +Required properties: +- compatible: + ilitek,ili210x for ILI210x + ilitek,ili251x for ILI251x + +- reg: The I2C address of the device + +- interrupts: The sink for the touchscreen's IRQ output + See ../interrupt-controller/interrupts.txt + +Optional properties for main touchpad device: + +- reset-gpios: GPIO specifier for the touchscreen's reset pin (active low) + +Example: + + touchscreen@41 { + compatible = "ilitek,ili251x"; + reg = <0x41>; + interrupt-parent = <&gpio4>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/input/msm-vibrator.txt b/Documentation/devicetree/bindings/input/msm-vibrator.txt new file mode 100644 index 000000000000..8dcf014ef2e5 --- /dev/null +++ b/Documentation/devicetree/bindings/input/msm-vibrator.txt @@ -0,0 +1,36 @@ +* Device tree bindings for the Qualcomm MSM vibrator + +Required properties: + + - compatible: Should be one of + "qcom,msm8226-vibrator" + "qcom,msm8974-vibrator" + - reg: the base address and length of the IO memory for the registers. + - pinctrl-names: set to default. + - pinctrl-0: phandles pointing to pin configuration nodes. See + Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + - clock-names: set to pwm + - clocks: phandle of the clock. See + Documentation/devicetree/bindings/clock/clock-bindings.txt + - enable-gpios: GPIO that enables the vibrator. + +Optional properties: + + - vcc-supply: phandle to the regulator that provides power to the sensor. + +Example from a LG Nexus 5 (hammerhead) phone: + +vibrator@fd8c3450 { + reg = <0xfd8c3450 0x400>; + compatible = "qcom,msm8974-vibrator"; + + vcc-supply = <&pm8941_l19>; + + clocks = <&mmcc CAMSS_GP1_CLK>; + clock-names = "pwm"; + + enable-gpios = <&msmgpio 60 GPIO_ACTIVE_HIGH>; + + pinctrl-names = "default"; + pinctrl-0 = <&vibrator_pin>; +}; diff --git a/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt b/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt new file mode 100644 index 000000000000..4494613ae7ad --- /dev/null +++ b/Documentation/devicetree/bindings/input/st,stpmic1-onkey.txt @@ -0,0 +1,28 @@ +STMicroelectronics STPMIC1 Onkey + +Required properties: + +- compatible = "st,stpmic1-onkey"; +- interrupts: interrupt line to use +- interrupt-names = "onkey-falling", "onkey-rising" + onkey-falling: happens when onkey is pressed; IT_PONKEY_F of pmic + onkey-rising: happens when onkey is released; IT_PONKEY_R of pmic + +Optional properties: + +- st,onkey-clear-cc-flag: onkey is able power on after an + over-current shutdown event. +- st,onkey-pu-inactive: onkey pull up is not active +- power-off-time-sec: Duration in seconds which the key should be kept + pressed for device to power off automatically (from 1 to 16 seconds). + see See Documentation/devicetree/bindings/input/keys.txt + +Example: + +onkey { + compatible = "st,stpmic1-onkey"; + interrupt-parent = <&pmic>; + interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt index da2dc5d6c98b..870b8c5cce9b 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt @@ -1,11 +1,12 @@ FocalTech EDT-FT5x06 Polytouch driver ===================================== -There are 3 variants of the chip for various touch panel sizes +There are 5 variants of the chip for various touch panel sizes FT5206GE1 2.8" .. 3.8" FT5306DE4 4.3" .. 7" FT5406EE8 7" .. 8.9" FT5506EEG 7" .. 8.9" +FT5726NEI 5.7” .. 11.6" The software interface is identical for all those chips, so that currently there is no need for the driver to distinguish between the @@ -19,6 +20,7 @@ Required properties: or: "edt,edt-ft5306" or: "edt,edt-ft5406" or: "edt,edt-ft5506" + or: "evervision,ev-ft5726" or: "focaltech,ft6236" - reg: I2C slave address of the chip (0x38) @@ -42,6 +44,15 @@ Optional properties: - offset: allows setting the edge compensation in the range from 0 to 31. + + - offset-x: Same as offset, but applies only to the horizontal position. + Range from 0 to 80, only supported by evervision,ev-ft5726 + devices. + + - offset-y: Same as offset, but applies only to the vertical position. + Range from 0 to 80, only supported by evervision,ev-ft5726 + devices. + - touchscreen-size-x : See touchscreen.txt - touchscreen-size-y : See touchscreen.txt - touchscreen-fuzz-x : See touchscreen.txt diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt index f7e95c52f3c7..8cf0b4d38a7e 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt @@ -3,6 +3,7 @@ Device tree bindings for Goodix GT9xx series touchscreen controller Required properties: - compatible : Should be "goodix,gt1151" + or "goodix,gt5688" or "goodix,gt911" or "goodix,gt9110" or "goodix,gt912" @@ -18,11 +19,14 @@ Optional properties: - irq-gpios : GPIO pin used for IRQ. The driver uses the interrupt gpio pin as output to reset the device. - reset-gpios : GPIO pin used for reset - - - touchscreen-inverted-x : X axis is inverted (boolean) - - touchscreen-inverted-y : Y axis is inverted (boolean) - - touchscreen-swapped-x-y : X and Y axis are swapped (boolean) - (swapping is done after inverting the axis) + - touchscreen-inverted-x + - touchscreen-inverted-y + - touchscreen-size-x + - touchscreen-size-y + - touchscreen-swapped-x-y + +The touchscreen-* properties are documented in touchscreen.txt in this +directory. Example: diff --git a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt index 64ad48b824a2..019373253b28 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt @@ -1,13 +1,17 @@ -* Sitronix st1232 touchscreen controller +* Sitronix st1232 or st1633 touchscreen controller Required properties: -- compatible: must be "sitronix,st1232" +- compatible: must contain one of + * "sitronix,st1232" + * "sitronix,st1633" - reg: I2C address of the chip - interrupts: interrupt to which the chip is connected Optional properties: - gpios: a phandle to the reset GPIO +For additional optional properties see: touchscreen.txt + Example: i2c@00000000 { diff --git a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt index 127baa31a77a..c549924603d2 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/stmpe.txt @@ -5,39 +5,105 @@ Required properties: - compatible: "st,stmpe-ts" Optional properties: -- st,sample-time: ADC converstion time in number of clock. (0 -> 36 clocks, 1 -> - 44 clocks, 2 -> 56 clocks, 3 -> 64 clocks, 4 -> 80 clocks, 5 -> 96 clocks, 6 - -> 144 clocks), recommended is 4. -- st,mod-12b: ADC Bit mode (0 -> 10bit ADC, 1 -> 12bit ADC) -- st,ref-sel: ADC reference source (0 -> internal reference, 1 -> external - reference) -- st,adc-freq: ADC Clock speed (0 -> 1.625 MHz, 1 -> 3.25 MHz, 2 || 3 -> 6.5 MHz) -- st,ave-ctrl: Sample average control (0 -> 1 sample, 1 -> 2 samples, 2 -> 4 - samples, 3 -> 8 samples) -- st,touch-det-delay: Touch detect interrupt delay (0 -> 10 us, 1 -> 50 us, 2 -> - 100 us, 3 -> 500 us, 4-> 1 ms, 5 -> 5 ms, 6 -> 10 ms, 7 -> 50 ms) recommended - is 3 -- st,settling: Panel driver settling time (0 -> 10 us, 1 -> 100 us, 2 -> 500 us, 3 - -> 1 ms, 4 -> 5 ms, 5 -> 10 ms, 6 for 50 ms, 7 -> 100 ms) recommended is 2 -- st,fraction-z: Length of the fractional part in z (fraction-z ([0..7]) = Count of - the fractional part) recommended is 7 -- st,i-drive: current limit value of the touchscreen drivers (0 -> 20 mA typical 35 - mA max, 1 -> 50 mA typical 80 mA max) +- st,ave-ctrl : Sample average control + 0 -> 1 sample + 1 -> 2 samples + 2 -> 4 samples + 3 -> 8 samples +- st,touch-det-delay : Touch detect interrupt delay (recommended is 3) + 0 -> 10 us + 1 -> 50 us + 2 -> 100 us + 3 -> 500 us + 4 -> 1 ms + 5 -> 5 ms + 6 -> 10 ms + 7 -> 50 ms +- st,settling : Panel driver settling time (recommended is 2) + 0 -> 10 us + 1 -> 100 us + 2 -> 500 us + 3 -> 1 ms + 4 -> 5 ms + 5 -> 10 ms + 6 -> 50 ms + 7 -> 100 ms +- st,fraction-z : Length of the fractional part in z (recommended is 7) + (fraction-z ([0..7]) = Count of the fractional part) +- st,i-drive : current limit value of the touchscreen drivers + 0 -> 20 mA (typical 35mA max) + 1 -> 50 mA (typical 80 mA max) + +Optional properties common with MFD (deprecated): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks + 1 -> 44 clocks + 2 -> 56 clocks + 3 -> 64 clocks + 4 -> 80 clocks (recommended) + 5 -> 96 clocks + 6 -> 124 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC + 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal + 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz + 1 -> 3.25 MHz + 2 || 3 -> 6.5 MHz Node name must be stmpe_touchscreen and should be child node of stmpe node to which it belongs. +Note that common ADC settings of stmpe_touchscreen (child) will take precedence +over the settings done in MFD. + Example: +stmpe811@41 { + compatible = "st,stmpe811"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_touch_int>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + interrupts = <10 IRQ_TYPE_LEVEL_LOW>; + interrupt-parent = <&gpio4>; + interrupt-controller; + id = <0>; + blocks = <0x5>; + irq-trigger = <0x1>; + /* Common ADC settings */ + /* 3.25 MHz ADC clock speed */ + st,adc-freq = <1>; + /* 12-bit ADC */ + st,mod-12b = <1>; + /* internal ADC reference */ + st,ref-sel = <0>; + /* ADC converstion time: 80 clocks */ + st,sample-time = <4>; + stmpe_touchscreen { compatible = "st,stmpe-ts"; - st,sample-time = <4>; - st,mod-12b = <1>; - st,ref-sel = <0>; - st,adc-freq = <1>; - st,ave-ctrl = <1>; - st,touch-det-delay = <2>; - st,settling = <2>; + reg = <0>; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 7 length fractional part in z */ st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ st,i-drive = <1>; }; + stmpe_adc { + compatible = "st,stmpe-adc"; + st,norequest-mask = <0x0F>; + }; +}; diff --git a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt index 4886c4aa2906..0ebe6dd043c7 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt @@ -1,10 +1,17 @@ * Semtech SX8654 I2C Touchscreen Controller Required properties: -- compatible: must be "semtech,sx8654" +- compatible: must be one of the following, depending on the model: + "semtech,sx8650" + "semtech,sx8654" + "semtech,sx8655" + "semtech,sx8656" - reg: i2c slave address - interrupts: touch controller interrupt +Optional properties: + - reset-gpios: GPIO specification for the NRST input + Example: sx8654@48 { @@ -12,4 +19,5 @@ Example: reg = <0x48>; interrupt-parent = <&gpio6>; interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt deleted file mode 100644 index a3be5298a5eb..000000000000 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ /dev/null @@ -1,175 +0,0 @@ -* ARM Generic Interrupt Controller, version 3 - -AArch64 SMP cores are often associated with a GICv3, providing Private -Peripheral Interrupts (PPI), Shared Peripheral Interrupts (SPI), -Software Generated Interrupts (SGI), and Locality-specific Peripheral -Interrupts (LPI). - -Main node required properties: - -- compatible : should at least contain "arm,gic-v3" or either - "qcom,msm8996-gic-v3", "arm,gic-v3" for msm8996 SoCs - to address SoC specific bugs/quirks -- interrupt-controller : Identifies the node as an interrupt controller -- #interrupt-cells : Specifies the number of cells needed to encode an - interrupt source. Must be a single cell with a value of at least 3. - If the system requires describing PPI affinity, then the value must - be at least 4. - - The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI - interrupts. Other values are reserved for future use. - - The 2nd cell contains the interrupt number for the interrupt type. - SPI interrupts are in the range [0-987]. PPI interrupts are in the - range [0-15]. - - The 3rd cell is the flags, encoded as follows: - bits[3:0] trigger type and level flags. - 1 = edge triggered - 4 = level triggered - - The 4th cell is a phandle to a node describing a set of CPUs this - interrupt is affine to. The interrupt must be a PPI, and the node - pointed must be a subnode of the "ppi-partitions" subnode. For - interrupt types other than PPI or PPIs that are not partitionned, - this cell must be zero. See the "ppi-partitions" node description - below. - - Cells 5 and beyond are reserved for future use and must have a value - of 0 if present. - -- reg : Specifies base physical address(s) and size of the GIC - registers, in the following order: - - GIC Distributor interface (GICD) - - GIC Redistributors (GICR), one range per redistributor region - - GIC CPU interface (GICC) - - GIC Hypervisor interface (GICH) - - GIC Virtual CPU interface (GICV) - - GICC, GICH and GICV are optional. - -- interrupts : Interrupt source of the VGIC maintenance interrupt. - -Optional - -- redistributor-stride : If using padding pages, specifies the stride - of consecutive redistributors. Must be a multiple of 64kB. - -- #redistributor-regions: The number of independent contiguous regions - occupied by the redistributors. Required if more than one such - region is present. - -- msi-controller: Boolean property. Identifies the node as an MSI - controller. Only present if the Message Based Interrupt - functionnality is being exposed by the HW, and the mbi-ranges - property present. - -- mbi-ranges: A list of pairs <intid span>, where "intid" is the first - SPI of a range that can be used an MBI, and "span" the size of that - range. Multiple ranges can be provided. Requires "msi-controller" to - be set. - -- mbi-alias: Address property. Base address of an alias of the GICD - region containing only the {SET,CLR}SPI registers to be used if - isolation is required, and if supported by the HW. - -Sub-nodes: - -PPI affinity can be expressed as a single "ppi-partitions" node, -containing a set of sub-nodes, each with the following property: -- affinity: Should be a list of phandles to CPU nodes (as described in - Documentation/devicetree/bindings/arm/cpus.yaml). - -GICv3 has one or more Interrupt Translation Services (ITS) that are -used to route Message Signalled Interrupts (MSI) to the CPUs. - -These nodes must have the following properties: -- compatible : Should at least contain "arm,gic-v3-its". -- msi-controller : Boolean property. Identifies the node as an MSI controller -- #msi-cells: Must be <1>. The single msi-cell is the DeviceID of the device - which will generate the MSI. -- reg: Specifies the base physical address and size of the ITS - registers. - -Optional: -- socionext,synquacer-pre-its: (u32, u32) tuple describing the untranslated - address and size of the pre-ITS window. - -The main GIC node must contain the appropriate #address-cells, -#size-cells and ranges properties for the reg property of all ITS -nodes. - -Examples: - - gic: interrupt-controller@2cf00000 { - compatible = "arm,gic-v3"; - #interrupt-cells = <3>; - #address-cells = <2>; - #size-cells = <2>; - ranges; - interrupt-controller; - reg = <0x0 0x2f000000 0 0x10000>, // GICD - <0x0 0x2f100000 0 0x200000>, // GICR - <0x0 0x2c000000 0 0x2000>, // GICC - <0x0 0x2c010000 0 0x2000>, // GICH - <0x0 0x2c020000 0 0x2000>; // GICV - interrupts = <1 9 4>; - - msi-controller; - mbi-ranges = <256 128>; - - gic-its@2c200000 { - compatible = "arm,gic-v3-its"; - msi-controller; - #msi-cells = <1>; - reg = <0x0 0x2c200000 0 0x20000>; - }; - }; - - gic: interrupt-controller@2c010000 { - compatible = "arm,gic-v3"; - #interrupt-cells = <4>; - #address-cells = <2>; - #size-cells = <2>; - ranges; - interrupt-controller; - redistributor-stride = <0x0 0x40000>; // 256kB stride - #redistributor-regions = <2>; - reg = <0x0 0x2c010000 0 0x10000>, // GICD - <0x0 0x2d000000 0 0x800000>, // GICR 1: CPUs 0-31 - <0x0 0x2e000000 0 0x800000>; // GICR 2: CPUs 32-63 - <0x0 0x2c040000 0 0x2000>, // GICC - <0x0 0x2c060000 0 0x2000>, // GICH - <0x0 0x2c080000 0 0x2000>; // GICV - interrupts = <1 9 4>; - - gic-its@2c200000 { - compatible = "arm,gic-v3-its"; - msi-controller; - #msi-cells = <1>; - reg = <0x0 0x2c200000 0 0x20000>; - }; - - gic-its@2c400000 { - compatible = "arm,gic-v3-its"; - msi-controller; - #msi-cells = <1>; - reg = <0x0 0x2c400000 0 0x20000>; - }; - - ppi-partitions { - part0: interrupt-partition-0 { - affinity = <&cpu0 &cpu2>; - }; - - part1: interrupt-partition-1 { - affinity = <&cpu1 &cpu3>; - }; - }; - }; - - - device@0 { - reg = <0 0 0 4>; - interrupts = <1 1 4 &part0>; - }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml new file mode 100644 index 000000000000..c34df35a25fc --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.yaml @@ -0,0 +1,279 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/arm,gic-v3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Generic Interrupt Controller, version 3 + +maintainers: + - Marc Zyngier <marc.zyngier@arm.com> + +description: | + AArch64 SMP cores are often associated with a GICv3, providing Private + Peripheral Interrupts (PPI), Shared Peripheral Interrupts (SPI), + Software Generated Interrupts (SGI), and Locality-specific Peripheral + Interrupts (LPI). + +allOf: + - $ref: /schemas/interrupt-controller.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - qcom,msm8996-gic-v3 + - const: arm,gic-v3 + - const: arm,gic-v3 + + interrupt-controller: true + + "#address-cells": + enum: [ 0, 1, 2 ] + "#size-cells": + enum: [ 1, 2 ] + + ranges: true + + "#interrupt-cells": + description: | + Specifies the number of cells needed to encode an interrupt source. + Must be a single cell with a value of at least 3. + If the system requires describing PPI affinity, then the value must + be at least 4. + + The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI + interrupts. Other values are reserved for future use. + + The 2nd cell contains the interrupt number for the interrupt type. + SPI interrupts are in the range [0-987]. PPI interrupts are in the + range [0-15]. + + The 3rd cell is the flags, encoded as follows: + bits[3:0] trigger type and level flags. + 1 = edge triggered + 4 = level triggered + + The 4th cell is a phandle to a node describing a set of CPUs this + interrupt is affine to. The interrupt must be a PPI, and the node + pointed must be a subnode of the "ppi-partitions" subnode. For + interrupt types other than PPI or PPIs that are not partitionned, + this cell must be zero. See the "ppi-partitions" node description + below. + + Cells 5 and beyond are reserved for future use and must have a value + of 0 if present. + enum: [ 3, 4 ] + + reg: + description: | + Specifies base physical address(s) and size of the GIC + registers, in the following order: + - GIC Distributor interface (GICD) + - GIC Redistributors (GICR), one range per redistributor region + - GIC CPU interface (GICC) + - GIC Hypervisor interface (GICH) + - GIC Virtual CPU interface (GICV) + + GICC, GICH and GICV are optional. + minItems: 2 + maxItems: 4096 # Should be enough? + + interrupts: + description: + Interrupt source of the VGIC maintenance interrupt. + maxItems: 1 + + redistributor-stride: + description: + If using padding pages, specifies the stride of consecutive + redistributors. Must be a multiple of 64kB. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint64 + - multipleOf: 0x10000 + exclusiveMinimum: 0 + + "#redistributor-regions": + description: + The number of independent contiguous regions occupied by the + redistributors. Required if more than one such region is present. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - maximum: 4096 # Should be enough? + + msi-controller: + description: + Only present if the Message Based Interrupt functionnality is + being exposed by the HW, and the mbi-ranges property present. + + mbi-ranges: + description: + A list of pairs <intid span>, where "intid" is the first SPI of a range + that can be used an MBI, and "span" the size of that range. Multiple + ranges can be provided. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-matrix + - items: + minItems: 2 + maxItems: 2 + + mbi-alias: + description: + Address property. Base address of an alias of the GICD region containing + only the {SET,CLR}SPI registers to be used if isolation is required, + and if supported by the HW. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - items: + minItems: 1 + maxItems: 2 + + ppi-partitions: + type: object + description: + PPI affinity can be expressed as a single "ppi-partitions" node, + containing a set of sub-nodes. + patternProperties: + "^interrupt-partition-[0-9]+$": + properties: + affinity: + $ref: /schemas/types.yaml#/definitions/phandle-array + description: + Should be a list of phandles to CPU nodes (as described in + Documentation/devicetree/bindings/arm/cpus.yaml). + + required: + - affinity + +dependencies: + mbi-ranges: [ msi-controller ] + msi-controller: [ mbi-ranges ] + +required: + - compatible + - interrupts + - reg + +patternProperties: + "^gic-its@": false + "^interrupt-controller@[0-9a-f]+$": false + # msi-controller is preferred, but allow other names + "^(msi-controller|gic-its|interrupt-controller)@[0-9a-f]+$": + type: object + description: + GICv3 has one or more Interrupt Translation Services (ITS) that are + used to route Message Signalled Interrupts (MSI) to the CPUs. + properties: + compatible: + const: arm,gic-v3-its + + msi-controller: true + + "#msi-cells": + description: + The single msi-cell is the DeviceID of the device which will generate + the MSI. + const: 1 + + reg: + description: + Specifies the base physical address and size of the ITS registers. + maxItems: 1 + + socionext,synquacer-pre-its: + description: + (u32, u32) tuple describing the untranslated + address and size of the pre-ITS window. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - items: + minItems: 2 + maxItems: 2 + + required: + - compatible + - msi-controller + - "#msi-cells" + - reg + + additionalProperties: false + +additionalProperties: false + +examples: + - | + gic: interrupt-controller@2cf00000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + interrupt-controller; + reg = <0x2f000000 0x10000>, // GICD + <0x2f100000 0x200000>, // GICR + <0x2c000000 0x2000>, // GICC + <0x2c010000 0x2000>, // GICH + <0x2c020000 0x2000>; // GICV + interrupts = <1 9 4>; + + msi-controller; + mbi-ranges = <256 128>; + + msi-controller@2c200000 { + compatible = "arm,gic-v3-its"; + msi-controller; + #msi-cells = <1>; + reg = <0x2c200000 0x20000>; + }; + }; + + interrupt-controller@2c010000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <4>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + interrupt-controller; + redistributor-stride = <0x0 0x40000>; // 256kB stride + #redistributor-regions = <2>; + reg = <0x2c010000 0x10000>, // GICD + <0x2d000000 0x800000>, // GICR 1: CPUs 0-31 + <0x2e000000 0x800000>, // GICR 2: CPUs 32-63 + <0x2c040000 0x2000>, // GICC + <0x2c060000 0x2000>, // GICH + <0x2c080000 0x2000>; // GICV + interrupts = <1 9 4>; + + msi-controller@2c200000 { + compatible = "arm,gic-v3-its"; + msi-controller; + #msi-cells = <1>; + reg = <0x2c200000 0x20000>; + }; + + msi-controller@2c400000 { + compatible = "arm,gic-v3-its"; + msi-controller; + #msi-cells = <1>; + reg = <0x2c400000 0x20000>; + }; + + ppi-partitions { + part0: interrupt-partition-0 { + affinity = <&cpu0 &cpu2>; + }; + + part1: interrupt-partition-1 { + affinity = <&cpu1 &cpu3>; + }; + }; + }; + + + device@0 { + reg = <0 4>; + interrupts = <1 1 4 &part0>; + }; + +... diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt deleted file mode 100644 index 2f3244648646..000000000000 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ /dev/null @@ -1,171 +0,0 @@ -* ARM Generic Interrupt Controller - -ARM SMP cores are often associated with a GIC, providing per processor -interrupts (PPI), shared processor interrupts (SPI) and software -generated interrupts (SGI). - -Primary GIC is attached directly to the CPU and typically has PPIs and SGIs. -Secondary GICs are cascaded into the upward interrupt controller and do not -have PPIs or SGIs. - -Main node required properties: - -- compatible : should be one of: - "arm,arm1176jzf-devchip-gic" - "arm,arm11mp-gic" - "arm,cortex-a15-gic" - "arm,cortex-a7-gic" - "arm,cortex-a9-gic" - "arm,eb11mp-gic" - "arm,gic-400" - "arm,pl390" - "arm,tc11mp-gic" - "brcm,brahma-b15-gic" - "nvidia,tegra210-agic" - "qcom,msm-8660-qgic" - "qcom,msm-qgic2" -- interrupt-controller : Identifies the node as an interrupt controller -- #interrupt-cells : Specifies the number of cells needed to encode an - interrupt source. The type shall be a <u32> and the value shall be 3. - - The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI - interrupts. - - The 2nd cell contains the interrupt number for the interrupt type. - SPI interrupts are in the range [0-987]. PPI interrupts are in the - range [0-15]. - - The 3rd cell is the flags, encoded as follows: - bits[3:0] trigger type and level flags. - 1 = low-to-high edge triggered - 2 = high-to-low edge triggered (invalid for SPIs) - 4 = active high level-sensitive - 8 = active low level-sensitive (invalid for SPIs). - bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of - the 8 possible cpus attached to the GIC. A bit set to '1' indicated - the interrupt is wired to that CPU. Only valid for PPI interrupts. - Also note that the configurability of PPI interrupts is IMPLEMENTATION - DEFINED and as such not guaranteed to be present (most SoC available - in 2014 seem to ignore the setting of this flag and use the hardware - default value). - -- reg : Specifies base physical address(s) and size of the GIC registers. The - first region is the GIC distributor register base and size. The 2nd region is - the GIC cpu interface register base and size. - -Optional -- interrupts : Interrupt source of the parent interrupt controller on - secondary GICs, or VGIC maintenance interrupt on primary GIC (see - below). - -- cpu-offset : per-cpu offset within the distributor and cpu interface - regions, used when the GIC doesn't have banked registers. The offset is - cpu-offset * cpu-nr. - -- clocks : List of phandle and clock-specific pairs, one for each entry - in clock-names. -- clock-names : List of names for the GIC clock input(s). Valid clock names - depend on the GIC variant: - "ic_clk" (for "arm,arm11mp-gic") - "PERIPHCLKEN" (for "arm,cortex-a15-gic") - "PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic") - "clk" (for "arm,gic-400" and "nvidia,tegra210") - "gclk" (for "arm,pl390") - -- power-domains : A phandle and PM domain specifier as defined by bindings of - the power controller specified by phandle, used when the GIC - is part of a Power or Clock Domain. - - -Example: - - intc: interrupt-controller@fff11000 { - compatible = "arm,cortex-a9-gic"; - #interrupt-cells = <3>; - #address-cells = <1>; - interrupt-controller; - reg = <0xfff11000 0x1000>, - <0xfff10100 0x100>; - }; - - -* GIC virtualization extensions (VGIC) - -For ARM cores that support the virtualization extensions, additional -properties must be described (they only exist if the GIC is the -primary interrupt controller). - -Required properties: - -- reg : Additional regions specifying the base physical address and - size of the VGIC registers. The first additional region is the GIC - virtual interface control register base and size. The 2nd additional - region is the GIC virtual cpu interface register base and size. - -- interrupts : VGIC maintenance interrupt. - -Example: - - interrupt-controller@2c001000 { - compatible = "arm,cortex-a15-gic"; - #interrupt-cells = <3>; - interrupt-controller; - reg = <0x2c001000 0x1000>, - <0x2c002000 0x2000>, - <0x2c004000 0x2000>, - <0x2c006000 0x2000>; - interrupts = <1 9 0xf04>; - }; - - -* GICv2m extension for MSI/MSI-x support (Optional) - -Certain revisions of GIC-400 supports MSI/MSI-x via V2M register frame(s). -This is enabled by specifying v2m sub-node(s). - -Required properties: - -- compatible : The value here should contain "arm,gic-v2m-frame". - -- msi-controller : Identifies the node as an MSI controller. - -- reg : GICv2m MSI interface register base and size - -Optional properties: - -- arm,msi-base-spi : When the MSI_TYPER register contains an incorrect - value, this property should contain the SPI base of - the MSI frame, overriding the HW value. - -- arm,msi-num-spis : When the MSI_TYPER register contains an incorrect - value, this property should contain the number of - SPIs assigned to the frame, overriding the HW value. - -Example: - - interrupt-controller@e1101000 { - compatible = "arm,gic-400"; - #interrupt-cells = <3>; - #address-cells = <2>; - #size-cells = <2>; - interrupt-controller; - interrupts = <1 8 0xf04>; - ranges = <0 0 0 0xe1100000 0 0x100000>; - reg = <0x0 0xe1110000 0 0x01000>, - <0x0 0xe112f000 0 0x02000>, - <0x0 0xe1140000 0 0x10000>, - <0x0 0xe1160000 0 0x10000>; - v2m0: v2m@8000 { - compatible = "arm,gic-v2m-frame"; - msi-controller; - reg = <0x0 0x80000 0 0x1000>; - }; - - .... - - v2mN: v2m@9000 { - compatible = "arm,gic-v2m-frame"; - msi-controller; - reg = <0x0 0x90000 0 0x1000>; - }; - }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.yaml b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.yaml new file mode 100644 index 000000000000..758fbd7128e7 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.yaml @@ -0,0 +1,223 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/interrupt-controller/arm,gic.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Generic Interrupt Controller v1 and v2 + +maintainers: + - Marc Zyngier <marc.zyngier@arm.com> + +description: |+ + ARM SMP cores are often associated with a GIC, providing per processor + interrupts (PPI), shared processor interrupts (SPI) and software + generated interrupts (SGI). + + Primary GIC is attached directly to the CPU and typically has PPIs and SGIs. + Secondary GICs are cascaded into the upward interrupt controller and do not + have PPIs or SGIs. + +allOf: + - $ref: /schemas/interrupt-controller.yaml# + +properties: + compatible: + oneOf: + - items: + - enum: + - arm,arm11mp-gic + - arm,cortex-a15-gic + - arm,cortex-a7-gic + - arm,cortex-a5-gic + - arm,cortex-a9-gic + - arm,eb11mp-gic + - arm,gic-400 + - arm,pl390 + - arm,tc11mp-gic + - nvidia,tegra210-agic + - qcom,msm-8660-qgic + - qcom,msm-qgic2 + + - items: + - const: arm,arm1176jzf-devchip-gic + - const: arm,arm11mp-gic + + - items: + - const: brcm,brahma-b15-gic + - const: arm,cortex-a15-gic + + interrupt-controller: true + + "#address-cells": + enum: [ 0, 1 ] + "#size-cells": + const: 1 + + "#interrupt-cells": + const: 3 + description: | + The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI + interrupts. + + The 2nd cell contains the interrupt number for the interrupt type. + SPI interrupts are in the range [0-987]. PPI interrupts are in the + range [0-15]. + + The 3rd cell is the flags, encoded as follows: + bits[3:0] trigger type and level flags. + 1 = low-to-high edge triggered + 2 = high-to-low edge triggered (invalid for SPIs) + 4 = active high level-sensitive + 8 = active low level-sensitive (invalid for SPIs). + bits[15:8] PPI interrupt cpu mask. Each bit corresponds to each of + the 8 possible cpus attached to the GIC. A bit set to '1' indicated + the interrupt is wired to that CPU. Only valid for PPI interrupts. + Also note that the configurability of PPI interrupts is IMPLEMENTATION + DEFINED and as such not guaranteed to be present (most SoC available + in 2014 seem to ignore the setting of this flag and use the hardware + default value). + + reg: + description: | + Specifies base physical address(s) and size of the GIC registers. The + first region is the GIC distributor register base and size. The 2nd region + is the GIC cpu interface register base and size. + + For GICv2 with virtualization extensions, additional regions are + required for specifying the base physical address and size of the VGIC + registers. The first additional region is the GIC virtual interface + control register base and size. The 2nd additional region is the GIC + virtual cpu interface register base and size. + minItems: 2 + maxItems: 4 + + interrupts: + description: Interrupt source of the parent interrupt controller on + secondary GICs, or VGIC maintenance interrupt on primary GIC (see + below). + maxItems: 1 + + cpu-offset: + description: per-cpu offset within the distributor and cpu interface + regions, used when the GIC doesn't have banked registers. The offset + is cpu-offset * cpu-nr. + $ref: /schemas/types.yaml#/definitions/uint32 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + description: List of names for the GIC clock input(s). Valid clock names + depend on the GIC variant. + oneOf: + - const: ic_clk # for "arm,arm11mp-gic" + - const: PERIPHCLKEN # for "arm,cortex-a15-gic" + - items: # for "arm,cortex-a9-gic" + - const: PERIPHCLK + - const: PERIPHCLKEN + - const: clk # for "arm,gic-400" and "nvidia,tegra210" + - const: gclk #for "arm,pl390" + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + +patternProperties: + "^v2m@[0-9a-f]+$": + description: | + * GICv2m extension for MSI/MSI-x support (Optional) + + Certain revisions of GIC-400 supports MSI/MSI-x via V2M register frame(s). + This is enabled by specifying v2m sub-node(s). + + properties: + compatible: + const: arm,gic-v2m-frame + + msi-controller: true + + reg: + maxItems: 1 + description: GICv2m MSI interface register base and size + + arm,msi-base-spi: + description: When the MSI_TYPER register contains an incorrect value, + this property should contain the SPI base of the MSI frame, overriding + the HW value. + $ref: /schemas/types.yaml#/definitions/uint32 + + arm,msi-num-spis: + description: When the MSI_TYPER register contains an incorrect value, + this property should contain the number of SPIs assigned to the + frame, overriding the HW value. + $ref: /schemas/types.yaml#/definitions/uint32 + + required: + - compatible + - msi-controller + - reg + + additionalProperties: false + +additionalProperties: false + +examples: + - | + // GICv1 + intc: interrupt-controller@fff11000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <1>; + interrupt-controller; + reg = <0xfff11000 0x1000>, + <0xfff10100 0x100>; + }; + + - | + // GICv2 + interrupt-controller@2c001000 { + compatible = "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x2c001000 0x1000>, + <0x2c002000 0x2000>, + <0x2c004000 0x2000>, + <0x2c006000 0x2000>; + interrupts = <1 9 0xf04>; + }; + + - | + // GICv2m extension for MSI/MSI-x support + interrupt-controller@e1101000 { + compatible = "arm,gic-400"; + #interrupt-cells = <3>; + #address-cells = <2>; + #size-cells = <2>; + interrupt-controller; + interrupts = <1 8 0xf04>; + ranges = <0 0 0 0xe1100000 0 0x100000>; + reg = <0x0 0xe1110000 0 0x01000>, + <0x0 0xe112f000 0 0x02000>, + <0x0 0xe1140000 0 0x10000>, + <0x0 0xe1160000 0 0x10000>; + + v2m0: v2m@8000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x0 0x80000 0 0x1000>; + }; + + //... + + v2mN: v2m@9000 { + compatible = "arm,gic-v2m-frame"; + msi-controller; + reg = <0x0 0x90000 0 0x1000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt index 8de96a4fb2d5..f977ea7617f6 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,irqc.txt @@ -16,6 +16,7 @@ Required properties: - "renesas,irqc-r8a7793" (R-Car M2-N) - "renesas,irqc-r8a7794" (R-Car E2) - "renesas,intc-ex-r8a774a1" (RZ/G2M) + - "renesas,intc-ex-r8a774c0" (RZ/G2E) - "renesas,intc-ex-r8a7795" (R-Car H3) - "renesas,intc-ex-r8a7796" (R-Car M3-W) - "renesas,intc-ex-r8a77965" (R-Car M3-N) diff --git a/Documentation/devicetree/bindings/iommu/nvidia,tegra20-gart.txt b/Documentation/devicetree/bindings/iommu/nvidia,tegra20-gart.txt deleted file mode 100644 index 099d9362ebc1..000000000000 --- a/Documentation/devicetree/bindings/iommu/nvidia,tegra20-gart.txt +++ /dev/null @@ -1,14 +0,0 @@ -NVIDIA Tegra 20 GART - -Required properties: -- compatible: "nvidia,tegra20-gart" -- reg: Two pairs of cells specifying the physical address and size of - the memory controller registers and the GART aperture respectively. - -Example: - - gart { - compatible = "nvidia,tegra20-gart"; - reg = <0x7000f024 0x00000018 /* controller registers */ - 0x58000000 0x02000000>; /* GART aperture */ - }; diff --git a/Documentation/devicetree/bindings/mailbox/xlnx,zynqmp-ipi-mailbox.txt b/Documentation/devicetree/bindings/mailbox/xlnx,zynqmp-ipi-mailbox.txt new file mode 100644 index 000000000000..4438432bfe9b --- /dev/null +++ b/Documentation/devicetree/bindings/mailbox/xlnx,zynqmp-ipi-mailbox.txt @@ -0,0 +1,127 @@ +Xilinx IPI Mailbox Controller +======================================== + +The Xilinx IPI(Inter Processor Interrupt) mailbox controller is to manage +messaging between two Xilinx Zynq UltraScale+ MPSoC IPI agents. Each IPI +agent owns registers used for notification and buffers for message. + + +-------------------------------------+ + | Xilinx ZynqMP IPI Controller | + +-------------------------------------+ + +--------------------------------------------------+ +ATF | | + | | + | | + +--------------------------+ | + | | + | | + +--------------------------------------------------+ + +------------------------------------------+ + | +----------------+ +----------------+ | +Hardware | | IPI Agent | | IPI Buffers | | + | | Registers | | | | + | | | | | | + | +----------------+ +----------------+ | + | | + | Xilinx IPI Agent Block | + +------------------------------------------+ + + +Controller Device Node: +=========================== +Required properties: +-------------------- +IPI agent node: +- compatible: Shall be: "xlnx,zynqmp-ipi-mailbox" +- interrupt-parent: Phandle for the interrupt controller +- interrupts: Interrupt information corresponding to the + interrupt-names property. +- xlnx,ipi-id: local Xilinx IPI agent ID +- #address-cells: number of address cells of internal IPI mailbox nodes +- #size-cells: number of size cells of internal IPI mailbox nodes + +Internal IPI mailbox node: +- reg: IPI buffers address ranges +- reg-names: Names of the reg resources. It should have: + * local_request_region + - IPI request msg buffer written by local and read + by remote + * local_response_region + - IPI response msg buffer written by local and read + by remote + * remote_request_region + - IPI request msg buffer written by remote and read + by local + * remote_response_region + - IPI response msg buffer written by remote and read + by local +- #mbox-cells: Shall be 1. It contains: + * tx(0) or rx(1) channel +- xlnx,ipi-id: remote Xilinx IPI agent ID of which the mailbox is + connected to. + +Optional properties: +-------------------- +- method: The method of accessing the IPI agent registers. + Permitted values are: "smc" and "hvc". Default is + "smc". + +Client Device Node: +=========================== +Required properties: +-------------------- +- mboxes: Standard property to specify a mailbox + (See ./mailbox.txt) +- mbox-names: List of identifier strings for each mailbox + channel. + +Example: +=========================== + zynqmp_ipi { + compatible = "xlnx,zynqmp-ipi-mailbox"; + interrupt-parent = <&gic>; + interrupts = <0 29 4>; + xlnx,ipi-id = <0>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + /* APU<->RPU0 IPI mailbox controller */ + ipi_mailbox_rpu0: mailbox@ff90400 { + reg = <0xff990400 0x20>, + <0xff990420 0x20>, + <0xff990080 0x20>, + <0xff9900a0 0x20>; + reg-names = "local_request_region", + "local_response_region", + "remote_request_region", + "remote_response_region"; + #mbox-cells = <1>; + xlnx,ipi-id = <1>; + }; + /* APU<->RPU1 IPI mailbox controller */ + ipi_mailbox_rpu1: mailbox@ff990440 { + reg = <0xff990440 0x20>, + <0xff990460 0x20>, + <0xff990280 0x20>, + <0xff9902a0 0x20>; + reg-names = "local_request_region", + "local_response_region", + "remote_request_region", + "remote_response_region"; + #mbox-cells = <1>; + xlnx,ipi-id = <2>; + }; + }; + rpu0 { + ... + mboxes = <&ipi_mailbox_rpu0 0>, + <&ipi_mailbox_rpu0 1>; + mbox-names = "tx", "rx"; + }; + rpu1 { + ... + mboxes = <&ipi_mailbox_rpu1 0>, + <&ipi_mailbox_rpu1 1>; + mbox-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt index 5dddc95f9cc4..4f91686e54a6 100644 --- a/Documentation/devicetree/bindings/media/i2c/adv748x.txt +++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt @@ -48,7 +48,16 @@ are numbered as follows. TXA source 10 TXB source 11 -The digital output port nodes must contain at least one endpoint. +The digital output port nodes, when present, shall contain at least one +endpoint. Each of those endpoints shall contain the data-lanes property as +described in video-interfaces.txt. + +Required source endpoint properties: + - data-lanes: an array of physical data lane indexes + The accepted value(s) for this property depends on which of the two + sources are described. For TXA 1, 2 or 4 data lanes can be described + while for TXB only 1 data lane is valid. See video-interfaces.txt + for detailed description. Ports are optional if they are not connected to anything at the hardware level. diff --git a/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt new file mode 100644 index 000000000000..060d2b7a5893 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/melexis,mlx90640.txt @@ -0,0 +1,20 @@ +* Melexis MLX90640 FIR Sensor + +Melexis MLX90640 FIR sensor support which allows recording of thermal data +with 32x24 resolution excluding 2 lines of coefficient data that is used by +userspace to render processed frames. + +Required Properties: + - compatible : Must be "melexis,mlx90640" + - reg : i2c address of the device + +Example: + + i2c0@1c22000 { + ... + mlx90640@33 { + compatible = "melexis,mlx90640"; + reg = <0x33>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m001.txt b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt new file mode 100644 index 000000000000..c920552b03ef --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/mt9m001.txt @@ -0,0 +1,38 @@ +MT9M001: 1/2-Inch Megapixel Digital Image Sensor + +The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital +image sensor. It is programmable through I2C interface. + +Required Properties: + +- compatible: shall be "onnn,mt9m001". +- clocks: reference to the master clock into sensor + +Optional Properties: + +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. + Active low. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. + Active high. + +The device node must contain one 'port' child node with one 'endpoint' child +sub-node for its digital output video port, in accordance with the video +interface bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + &i2c1 { + camera-sensor@5d { + compatible = "onnn,mt9m001"; + reg = <0x5d>; + reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + standby-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + clocks = <&camera_clk>; + port { + mt9m001_out: endpoint { + remote-endpoint = <&vcap_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt index fd7aec9f8e24..72ad992f77be 100644 --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt +++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt @@ -26,9 +26,9 @@ Example: &i2c1 { ... - ov5645: ov5645@78 { + ov5645: ov5645@3c { compatible = "ovti,ov5645"; - reg = <0x78>; + reg = <0x3c>; enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; @@ -37,7 +37,7 @@ Example: clocks = <&clks 200>; clock-names = "xclk"; - clock-frequency = <23880000>; + clock-frequency = <24000000>; vdddo-supply = <&camera_dovdd_1v8>; vdda-supply = <&camera_avdd_2v8>; diff --git a/Documentation/devicetree/bindings/media/imx7-csi.txt b/Documentation/devicetree/bindings/media/imx7-csi.txt new file mode 100644 index 000000000000..3c07bc676bc3 --- /dev/null +++ b/Documentation/devicetree/bindings/media/imx7-csi.txt @@ -0,0 +1,45 @@ +Freescale i.MX7 CMOS Sensor Interface +===================================== + +csi node +-------- + +This is device node for the CMOS Sensor Interface (CSI) which enables the chip +to connect directly to external CMOS image sensors. + +Required properties: + +- compatible : "fsl,imx7-csi"; +- reg : base address and length of the register set for the device; +- interrupts : should contain CSI interrupt; +- clocks : list of clock specifiers, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details; +- clock-names : must contain "axi", "mclk" and "dcic" entries, matching + entries in the clock property; + +The device node shall contain one 'port' child node with one child 'endpoint' +node, according to the bindings defined in: +Documentation/devicetree/bindings/media/video-interfaces.txt. + +In the following example a remote endpoint is a video multiplexer. + +example: + + csi: csi@30710000 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "fsl,imx7-csi"; + reg = <0x30710000 0x10000>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_CLK_DUMMY>, + <&clks IMX7D_CSI_MCLK_ROOT_CLK>, + <&clks IMX7D_CLK_DUMMY>; + clock-names = "axi", "mclk", "dcic"; + + port { + csi_from_csi_mux: endpoint { + remote-endpoint = <&csi_mux_to_csi>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt new file mode 100644 index 000000000000..71fd74ed3ec8 --- /dev/null +++ b/Documentation/devicetree/bindings/media/imx7-mipi-csi2.txt @@ -0,0 +1,90 @@ +Freescale i.MX7 Mipi CSI2 +========================= + +mipi_csi2 node +-------------- + +This is the device node for the MIPI CSI-2 receiver core in i.MX7 SoC. It is +compatible with previous version of Samsung D-phy. + +Required properties: + +- compatible : "fsl,imx7-mipi-csi2"; +- reg : base address and length of the register set for the device; +- interrupts : should contain MIPI CSIS interrupt; +- clocks : list of clock specifiers, see + Documentation/devicetree/bindings/clock/clock-bindings.txt for details; +- clock-names : must contain "pclk", "wrap" and "phy" entries, matching + entries in the clock property; +- power-domains : a phandle to the power domain, see + Documentation/devicetree/bindings/power/power_domain.txt for details. +- reset-names : should include following entry "mrst"; +- resets : a list of phandle, should contain reset entry of + reset-names; +- phy-supply : from the generic phy bindings, a phandle to a regulator that + provides power to MIPI CSIS core; + +Optional properties: + +- clock-frequency : The IP's main (system bus) clock frequency in Hz, default + value when this property is not specified is 166 MHz; +- fsl,csis-hs-settle : differential receiver (HS-RX) settle time; + +The device node should contain two 'port' child nodes with one child 'endpoint' +node, according to the bindings defined in: + Documentation/devicetree/bindings/ media/video-interfaces.txt. + The following are properties specific to those nodes. + +port node +--------- + +- reg : (required) can take the values 0 or 1, where 0 shall be + related to the sink port and port 1 shall be the source + one; + +endpoint node +------------- + +- data-lanes : (required) an array specifying active physical MIPI-CSI2 + data input lanes and their mapping to logical lanes; this + shall only be applied to port 0 (sink port), the array's + content is unused only its length is meaningful, + in this case the maximum length supported is 2; + +example: + + mipi_csi: mipi-csi@30750000 { + #address-cells = <1>; + #size-cells = <0>; + + compatible = "fsl,imx7-mipi-csi2"; + reg = <0x30750000 0x10000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX7D_IPG_ROOT_CLK>, + <&clks IMX7D_MIPI_CSI_ROOT_CLK>, + <&clks IMX7D_MIPI_DPHY_ROOT_CLK>; + clock-names = "pclk", "wrap", "phy"; + clock-frequency = <166000000>; + power-domains = <&pgc_mipi_phy>; + phy-supply = <®_1p0d>; + resets = <&src IMX7_RESET_MIPI_PHY_MRST>; + reset-names = "mrst"; + fsl,csis-hs-settle = <3>; + + port@0 { + reg = <0>; + + mipi_from_sensor: endpoint { + remote-endpoint = <&ov2680_to_mipi>; + data-lanes = <1>; + }; + }; + + port@1 { + reg = <1>; + + mipi_vc0_to_csi_mux: endpoint { + remote-endpoint = <&csi_mux_from_mipi_vc0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt index 2a615d84a682..b6b5dde6abd8 100644 --- a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt +++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt @@ -66,6 +66,15 @@ vcodec_dec: vcodec@16000000 { "vencpll", "venc_lt_sel", "vdec_bus_clk_src"; + assigned-clocks = <&topckgen CLK_TOP_VENC_LT_SEL>, + <&topckgen CLK_TOP_CCI400_SEL>, + <&topckgen CLK_TOP_VDEC_SEL>, + <&apmixedsys CLK_APMIXED_VCODECPLL>, + <&apmixedsys CLK_APMIXED_VENCPLL>; + assigned-clock-parents = <&topckgen CLK_TOP_VCODECPLL_370P5>, + <&topckgen CLK_TOP_UNIVPLL_D2>, + <&topckgen CLK_TOP_VCODECPLL>; + assigned-clock-rates = <0>, <0>, <0>, <1482000000>, <800000000>; }; vcodec_enc: vcodec@18002000 { @@ -105,4 +114,8 @@ vcodec_dec: vcodec@16000000 { "venc_sel", "venc_lt_sel_src", "venc_lt_sel"; + assigned-clocks = <&topckgen CLK_TOP_VENC_SEL>, + <&topckgen CLK_TOP_VENC_LT_SEL>; + assigned-clock-parents = <&topckgen CLK_TOP_VENCPLL_D2>, + <&topckgen CLK_TOP_UNIVPLL1_D2>; }; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 0dd84a183ca7..224a4615b418 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -7,12 +7,13 @@ family of devices. Each VIN instance has a single parallel input that supports RGB and YUV video, with both external synchronization and BT.656 synchronization for the latter. Depending on the instance the VIN input is connected to external SoC pins, or -on Gen3 platforms to a CSI-2 receiver. +on Gen3 and RZ/G2 platforms to a CSI-2 receiver. - compatible: Must be one or more of the following - "renesas,vin-r8a7743" for the R8A7743 device - "renesas,vin-r8a7744" for the R8A7744 device - "renesas,vin-r8a7745" for the R8A7745 device + - "renesas,vin-r8a774c0" for the R8A774C0 device - "renesas,vin-r8a7778" for the R8A7778 device - "renesas,vin-r8a7779" for the R8A7779 device - "renesas,vin-r8a7790" for the R8A7790 device @@ -61,10 +62,10 @@ The per-board settings Gen2 platforms: - data-enable-active: polarity of CLKENB signal, see [1] for description. Default is active high. -The per-board settings Gen3 platforms: +The per-board settings Gen3 and RZ/G2 platforms: -Gen3 platforms can support both a single connected parallel input source -from external SoC pins (port@0) and/or multiple parallel input sources +Gen3 and RZ/G2 platforms can support both a single connected parallel input +source from external SoC pins (port@0) and/or multiple parallel input sources from local SoC CSI-2 receivers (port@1) depending on SoC. - renesas,id - ID number of the VIN, VINx in the documentation. diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt index 3ec91803ba58..79c37395b396 100644 --- a/Documentation/devicetree/bindings/media/renesas,fcp.txt +++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt @@ -2,8 +2,9 @@ Renesas R-Car Frame Compression Processor (FCP) ----------------------------------------------- The FCP is a companion module of video processing modules in the Renesas R-Car -Gen3 SoCs. It provides data compression and decompression, data caching, and -conversion of AXI transactions in order to reduce the memory bandwidth. +Gen3 and RZ/G2 SoCs. It provides data compression and decompression, data +caching, and conversion of AXI transactions in order to reduce the memory +bandwidth. There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP for FDP (FCPF). Their configuration and behaviour depend on the module they diff --git a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt index 541d936b62e8..d63275e17afd 100644 --- a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt +++ b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt @@ -2,12 +2,13 @@ Renesas R-Car MIPI CSI-2 ------------------------ The R-Car CSI-2 receiver device provides MIPI CSI-2 capabilities for the -Renesas R-Car family of devices. It is used in conjunction with the +Renesas R-Car and RZ/G2 family of devices. It is used in conjunction with the R-Car VIN module, which provides the video capture capabilities. Mandatory properties -------------------- - compatible: Must be one or more of the following + - "renesas,r8a774c0-csi2" for the R8A774C0 device. - "renesas,r8a7795-csi2" for the R8A7795 device. - "renesas,r8a7796-csi2" for the R8A7796 device. - "renesas,r8a77965-csi2" for the R8A77965 device. diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 16427017cb45..cd5a955b2ea0 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -2,13 +2,13 @@ The VSP is a video processing engine that supports up-/down-scaling, alpha blending, color space conversion and various other image processing features. -It can be found in the Renesas R-Car second generation SoCs. +It can be found in the Renesas R-Car Gen2, R-Car Gen3, RZ/G1, and RZ/G2 SoCs. Required properties: - compatible: Must contain one of the following values - - "renesas,vsp1" for the R-Car Gen2 VSP1 - - "renesas,vsp2" for the R-Car Gen3 VSP2 + - "renesas,vsp1" for the R-Car Gen2 and RZ/G1 VSP1 + - "renesas,vsp2" for the R-Car Gen3 and RZ/G2 VSP2 - reg: Base address and length of the registers block for the VSP. - interrupts: VSP interrupt specifier. diff --git a/Documentation/devicetree/bindings/media/si470x.txt b/Documentation/devicetree/bindings/media/si470x.txt new file mode 100644 index 000000000000..a9403558362e --- /dev/null +++ b/Documentation/devicetree/bindings/media/si470x.txt @@ -0,0 +1,26 @@ +* Silicon Labs FM Radio receiver + +The Silicon Labs Si470x is family of FM radio receivers with receive power scan +supporting 76-108 MHz, programmable through an I2C interface. +Some of them includes an RDS encoder. + +Required Properties: +- compatible: Should contain "silabs,si470x" +- reg: the I2C address of the device + +Optional Properties: +- interrupts : The interrupt number +- reset-gpios: GPIO specifier for the chips reset line + +Example: + +&i2c2 { + si470x@63 { + compatible = "silabs,si470x"; + reg = <0x63>; + + interrupt-parent = <&gpj2>; + interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpj2 5 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/media/sun6i-csi.txt b/Documentation/devicetree/bindings/media/sun6i-csi.txt index d4ab34f2240c..0dd540bb03db 100644 --- a/Documentation/devicetree/bindings/media/sun6i-csi.txt +++ b/Documentation/devicetree/bindings/media/sun6i-csi.txt @@ -6,8 +6,9 @@ Allwinner V3s SoC features a CSI module(CSI1) with parallel interface. Required properties: - compatible: value must be one of: * "allwinner,sun6i-a31-csi" - * "allwinner,sun8i-h3-csi", "allwinner,sun6i-a31-csi" + * "allwinner,sun8i-h3-csi" * "allwinner,sun8i-v3s-csi" + * "allwinner,sun50i-a64-csi" - reg: base address and size of the memory-mapped region. - interrupts: interrupt associated to this IP - clocks: phandles to the clocks feeding the CSI diff --git a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.txt b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.txt index 7d60a50a4fa1..e55328237df4 100644 --- a/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/nvidia,tegra20-mc.txt @@ -1,26 +1,37 @@ NVIDIA Tegra20 MC(Memory Controller) Required properties: -- compatible : "nvidia,tegra20-mc" -- reg : Should contain 2 register ranges(address and length); see the - example below. Note that the MC registers are interleaved with the - GART registers, and hence must be represented as multiple ranges. +- compatible : "nvidia,tegra20-mc-gart" +- reg : Should contain 2 register ranges: physical base address and length of + the controller's registers and the GART aperture respectively. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - mc: the module's clock input - interrupts : Should contain MC General interrupt. - #reset-cells : Should be 1. This cell represents memory client module ID. The assignments may be found in header file <dt-bindings/memory/tegra20-mc.h> or in the TRM documentation. +- #iommu-cells: Should be 0. This cell represents the number of cells in an + IOMMU specifier needed to encode an address. GART supports only a single + address space that is shared by all devices, therefore no additional + information needed for the address encoding. Example: mc: memory-controller@7000f000 { - compatible = "nvidia,tegra20-mc"; - reg = <0x7000f000 0x024 - 0x7000f03c 0x3c4>; - interrupts = <0 77 0x04>; + compatible = "nvidia,tegra20-mc-gart"; + reg = <0x7000f000 0x400 /* controller registers */ + 0x58000000 0x02000000>; /* GART aperture */ + clocks = <&tegra_car TEGRA20_CLK_MC>; + clock-names = "mc"; + interrupts = <GIC_SPI 77 0x04>; #reset-cells = <1>; + #iommu-cells = <0>; }; video-codec@6001a000 { compatible = "nvidia,tegra20-vde"; ... resets = <&mc TEGRA20_MC_RESET_VDE>; + iommus = <&mc>; }; diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt index 34dd89087cff..86446074e206 100644 --- a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt +++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt @@ -135,6 +135,8 @@ Required properties: - clocks: contains a phandle to the syscon node describing the clocks. There should then be one cell representing the clock to use +Optional properties: + - memory-region: A phandle to a reserved_memory region to be used for the LPC to AHB mapping diff --git a/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt new file mode 100644 index 000000000000..004b0158cf4d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/cirrus,lochnagar.txt @@ -0,0 +1,68 @@ +Cirrus Logic Lochnagar Audio Development Board + +Lochnagar is an evaluation and development board for Cirrus Logic +Smart CODEC and Amp devices. It allows the connection of most Cirrus +Logic devices on mini-cards, as well as allowing connection of +various application processor systems to provide a full evaluation +platform. Audio system topology, clocking and power can all be +controlled through the Lochnagar, allowing the device under test +to be used in a variety of possible use cases. + +Also see these documents for generic binding information: + [1] GPIO : ../gpio/gpio.txt + +And these for relevant defines: + [2] include/dt-bindings/pinctrl/lochnagar.h + [3] include/dt-bindings/clock/lochnagar.h + +And these documents for the required sub-node binding details: + [4] Clock: ../clock/cirrus,lochnagar.txt + [5] Pinctrl: ../pinctrl/cirrus,lochnagar.txt + [6] Regulator: ../regulator/cirrus,lochnagar.txt + +Required properties: + + - compatible : One of the following strings: + "cirrus,lochnagar1" + "cirrus,lochnagar2" + + - reg : I2C slave address + + - reset-gpios : Reset line to the Lochnagar, see [1]. + +Required sub-nodes: + + - lochnagar-clk : Binding for the clocking components, see [4]. + + - lochnagar-pinctrl : Binding for the pin control components, see [5]. + +Optional sub-nodes: + + - Bindings for the regulator components, see [6]. Only available on + Lochnagar 2. + +Optional properties: + + - present-gpios : Host present line, indicating the presence of a + host system, see [1]. This can be omitted if the present line is + tied in hardware. + +Example: + +lochnagar: lochnagar@22 { + compatible = "cirrus,lochnagar2"; + reg = <0x22>; + + reset-gpios = <&gpio0 55 0>; + present-gpios = <&gpio0 60 0>; + + lochnagar-clk { + compatible = "cirrus,lochnagar2-clk"; + ... + }; + + lochnagar-pinctrl { + compatible = "cirrus,lochnagar-pinctrl"; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/st,stpmic1.txt b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt new file mode 100644 index 000000000000..afd45c089585 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/st,stpmic1.txt @@ -0,0 +1,61 @@ +* STMicroelectronics STPMIC1 Power Management IC + +Required properties: +- compatible: : "st,stpmic1" +- reg: : The I2C slave address for the STPMIC1 chip. +- interrupts: : The interrupt line the device is connected to. +- #interrupt-cells: : Should be 1. +- interrupt-controller: : Marks the device node as an interrupt controller. + Interrupt numbers are defined at + dt-bindings/mfd/st,stpmic1.h. + +STPMIC1 consists in a varied group of sub-devices. +Each sub-device binding is be described in own documentation file. + +Device Description +------ ------------ +st,stpmic1-onkey : Power on key, see ../input/st,stpmic1-onkey.txt +st,stpmic1-regulators : Regulators, see ../regulator/st,stpmic1-regulator.txt +st,stpmic1-wdt : Watchdog, see ../watchdog/st,stpmic1-wdt.txt + +Example: + +#include <dt-bindings/mfd/st,stpmic1.h> + +pmic: pmic@33 { + compatible = "st,stpmic1"; + reg = <0x33>; + interrupt-parent = <&gpioa>; + interrupts = <0 2>; + + interrupt-controller; + #interrupt-cells = <2>; + + onkey { + compatible = "st,stpmic1-onkey"; + interrupts = <IT_PONKEY_F 0>,<IT_PONKEY_R 1>; + interrupt-names = "onkey-falling", "onkey-rising"; + power-off-time-sec = <10>; + }; + + watchdog { + compatible = "st,stpmic1-wdt"; + }; + + regulators { + compatible = "st,stpmic1-regulators"; + + vdd_core: buck1 { + regulator-name = "vdd_core"; + regulator-boot-on; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1200000>; + }; + vdd: buck3 { + regulator-name = "vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-pull-down; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/stmpe.txt b/Documentation/devicetree/bindings/mfd/stmpe.txt index c797c05cd3c2..d4408a417193 100644 --- a/Documentation/devicetree/bindings/mfd/stmpe.txt +++ b/Documentation/devicetree/bindings/mfd/stmpe.txt @@ -4,15 +4,29 @@ STMPE is an MFD device which may expose the following inbuilt devices: gpio, keypad, touchscreen, adc, pwm, rotator. Required properties: - - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" - - reg : I2C/SPI address of the device + - compatible : "st,stmpe[610|801|811|1600|1601|2401|2403]" + - reg : I2C/SPI address of the device Optional properties: - - interrupts : The interrupt outputs from the controller - - interrupt-controller : Marks the device node as an interrupt controller - - wakeup-source : Marks the input device as wakable - - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 - - irq-gpio : If present, which GPIO to use for event IRQ + - interrupts : The interrupt outputs from the controller + - interrupt-controller : Marks the device node as an interrupt controller + - wakeup-source : Marks the input device as wakable + - st,autosleep-timeout : Valid entries (ms); 4, 16, 32, 64, 128, 256, 512 and 1024 + - irq-gpio : If present, which GPIO to use for event IRQ + +Optional properties for devices with touch and ADC (STMPE811|STMPE610): + - st,sample-time : ADC conversion time in number of clock. + 0 -> 36 clocks 4 -> 80 clocks (recommended) + 1 -> 44 clocks 5 -> 96 clocks + 2 -> 56 clocks 6 -> 124 clocks + 3 -> 64 clocks + - st,mod-12b : ADC Bit mode + 0 -> 10bit ADC 1 -> 12bit ADC + - st,ref-sel : ADC reference source + 0 -> internal 1 -> external + - st,adc-freq : ADC Clock speed + 0 -> 1.625 MHz 2 || 3 -> 6.5 MHz + 1 -> 3.25 MHz Example: diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index 35694c0c376b..d66a5292b9d3 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -71,6 +71,10 @@ properties, described in binding documents: Documentation/devicetree/bindings/net/fixed-link.txt for details. +- local-mac-address : See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + Example The following example shows three switches on three MDIO busses, @@ -97,6 +101,7 @@ linked into one DSA cluster. port@1 { reg = <1>; label = "lan1"; + local-mac-address = [00 00 00 00 00 00]; }; port@2 { diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt index bbcb255c3150..93a7469e70d4 100644 --- a/Documentation/devicetree/bindings/net/dsa/qca8k.txt +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -12,10 +12,15 @@ Required properties: Subnodes: The integrated switch subnode should be specified according to the binding -described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of -port and PHY id, each subnode describing a port needs to have a valid phandle -referencing the internal PHY connected to it. The CPU port of this switch is -always port 0. +described in dsa/dsa.txt. If the QCA8K switch is connect to a SoC's external +mdio-bus each subnode describing a port needs to have a valid phandle +referencing the internal PHY it is connected to. This is because there's no +N:N mapping of port and PHY id. + +Don't use mixed external and internal mdio-bus configurations, as this is +not supported by the hardware. + +The CPU port of this switch is always port 0. A CPU port node has the following optional node: @@ -31,8 +36,9 @@ For QCA8K the 'fixed-link' sub-node supports only the following properties: - 'full-duplex' (boolean, optional), to indicate that full duplex is used. When absent, half duplex is assumed. -Example: +Examples: +for the external mdio-bus configuration: &mdio0 { phy_port1: phy@0 { @@ -55,12 +61,12 @@ Example: reg = <4>; }; - switch0@0 { + switch@10 { compatible = "qca,qca8337"; #address-cells = <1>; #size-cells = <0>; - reg = <0>; + reg = <0x10>; ports { #address-cells = <1>; @@ -108,3 +114,56 @@ Example: }; }; }; + +for the internal master mdio-bus configuration: + + &mdio0 { + switch@10 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0x10>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = 1000; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "wan"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.txt b/Documentation/devicetree/bindings/net/stm32-dwmac.txt index 1341012722aa..a90eef11dc46 100644 --- a/Documentation/devicetree/bindings/net/stm32-dwmac.txt +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.txt @@ -14,8 +14,7 @@ Required properties: - clock-names: Should be "stmmaceth" for the host clock. Should be "mac-clk-tx" for the MAC TX clock. Should be "mac-clk-rx" for the MAC RX clock. - For MPU family need to add also "ethstp" for power mode clock and, - "syscfg-clk" for SYSCFG clock. + For MPU family need to add also "ethstp" for power mode clock - interrupt-names: Should contain a list of interrupt names corresponding to the interrupts in the interrupts property, if available. Should be "macirq" for the main MAC IRQ @@ -24,9 +23,9 @@ Required properties: encompases the glue register, and the offset of the control register. Optional properties: -- clock-names: For MPU family "mac-clk-ck" for PHY without quartz -- st,int-phyclk (boolean) : valid only where PHY do not have quartz and need to be clock - by RCC +- clock-names: For MPU family "eth-ck" for PHY without quartz +- st,eth-clk-sel (boolean) : set this property in RGMII PHY when you want to select RCC clock instead of ETH_CLK125. +- st,eth-ref-clk-sel (boolean) : set this property in RMII mode when you have PHY without crystal 50MHz and want to select RCC clock instead of ETH_REF_CLK. Example: diff --git a/Documentation/devicetree/bindings/pci/altera-pcie.txt b/Documentation/devicetree/bindings/pci/altera-pcie.txt index 6c396f17c91a..816b244a221e 100644 --- a/Documentation/devicetree/bindings/pci/altera-pcie.txt +++ b/Documentation/devicetree/bindings/pci/altera-pcie.txt @@ -1,11 +1,13 @@ * Altera PCIe controller Required properties: -- compatible : should contain "altr,pcie-root-port-1.0" +- compatible : should contain "altr,pcie-root-port-1.0" or "altr,pcie-root-port-2.0" - reg: a list of physical base address and length for TXS and CRA. + For "altr,pcie-root-port-2.0", additional HIP base address and length. - reg-names: must include the following entries: "Txs": TX slave port region "Cra": Control register access region + "Hip": Hard IP region (if "altr,pcie-root-port-2.0") - interrupts: specifies the interrupt source of the parent interrupt controller. The format of the interrupt specifier depends on the parent interrupt controller. diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index d514c1f2365f..a7f5f5afa0e6 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -9,6 +9,7 @@ Required properties: - "fsl,imx6sx-pcie", - "fsl,imx6qp-pcie" - "fsl,imx7d-pcie" + - "fsl,imx8mq-pcie" - reg: base address and length of the PCIe controller - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. @@ -45,7 +46,7 @@ Additional required properties for imx6sx-pcie: PCIE_PHY power domains - power-domain-names: Must be "pcie", "pcie_phy" -Additional required properties for imx7d-pcie: +Additional required properties for imx7d-pcie and imx8mq-pcie: - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain - resets: Must contain phandles to PCIe-related reset lines exposed by SRC IP block @@ -53,6 +54,11 @@ Additional required properties for imx7d-pcie: - "pciephy" - "apps" - "turnoff" +- fsl,imx7d-pcie-phy: A phandle to an fsl,imx7d-pcie-phy node. + +Additional required properties for imx8mq-pcie: +- clock-names: Must include the following additional entries: + - "pcie_aux" Example: @@ -79,3 +85,13 @@ Example: clocks = <&clks 144>, <&clks 206>, <&clks 189>; clock-names = "pcie", "pcie_bus", "pcie_phy"; }; + +* Freescale i.MX7d PCIe PHY + +This is the PHY associated with the IMX7d PCIe controller. It's used by the +PCI-e controller via the fsl,imx7d-pcie-phy phandle. + +Required properties: +- compatible: + - "fsl,imx7d-pcie-phy" +- reg: base address and length of the PCIe PHY controller diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt index 9b2b8d66d1f4..e20ceaab9b38 100644 --- a/Documentation/devicetree/bindings/pci/layerscape-pci.txt +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -13,6 +13,7 @@ information. Required properties: - compatible: should contain the platform identifier such as: + RC mode: "fsl,ls1021a-pcie" "fsl,ls2080a-pcie", "fsl,ls2085a-pcie" "fsl,ls2088a-pcie" @@ -20,6 +21,8 @@ Required properties: "fsl,ls1046a-pcie" "fsl,ls1043a-pcie" "fsl,ls1012a-pcie" + EP mode: + "fsl,ls1046a-pcie-ep", "fsl,ls-pcie-ep" - reg: base addresses and lengths of the PCIe controller register blocks. - interrupts: A list of interrupt outputs of the controller. Must contain an entry for each entry in the interrupt-names property. diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt index 976ef7bfff93..6904882a0e94 100644 --- a/Documentation/devicetree/bindings/pci/rcar-pci.txt +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -3,6 +3,7 @@ Required properties: compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a7744" for the R8A7744 SoC; + "renesas,pcie-r8a774c0" for the R8A774C0 SoC; "renesas,pcie-r8a7779" for the R8A7779 SoC; "renesas,pcie-r8a7790" for the R8A7790 SoC; "renesas,pcie-r8a7791" for the R8A7791 SoC; @@ -13,7 +14,8 @@ compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; "renesas,pcie-r8a77990" for the R8A77990 SoC; "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or RZ/G1 compatible device. - "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. + "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 or + RZ/G2 compatible device. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt index 452fe48c4fdd..d5cbfe6b0d89 100644 --- a/Documentation/devicetree/bindings/pci/ti-pci.txt +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -1,14 +1,21 @@ TI PCI Controllers PCIe DesignWare Controller - - compatible: Should be "ti,dra7-pcie" for RC - Should be "ti,dra7-pcie-ep" for EP + - compatible: Should be "ti,dra7-pcie" for RC (deprecated) + Should be "ti,dra7-pcie-ep" for EP (deprecated) + Should be "ti,dra746-pcie-rc" for dra74x/dra76 in RC mode + Should be "ti,dra746-pcie-ep" for dra74x/dra76 in EP mode + Should be "ti,dra726-pcie-rc" for dra72x in RC mode + Should be "ti,dra726-pcie-ep" for dra72x in EP mode - phys : list of PHY specifiers (used by generic PHY framework) - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the number of PHYs as specified in *phys* property. - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", where <X> is the instance number of the pcie from the HW spec. - num-lanes as specified in ../designware-pcie.txt + - ti,syscon-lane-sel : phandle/offset pair. Phandle to the system control + module and the register offset to specify lane + selection. HOST MODE ========= diff --git a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt index 3e23fece99da..eb39f5051159 100644 --- a/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/atmel,at91-pinctrl.txt @@ -19,7 +19,7 @@ such as pull-up, multi drive, etc. Required properties for iomux controller: - compatible: "atmel,at91rm9200-pinctrl" or "atmel,at91sam9x5-pinctrl" - or "atmel,sama5d3-pinctrl" + or "atmel,sama5d3-pinctrl" or "microchip,sam9x60-pinctrl" - atmel,mux-mask: array of mask (periph per bank) to describe if a pin can be configured in this periph mode. All the periph and bank need to be describe. @@ -100,6 +100,7 @@ DRIVE_STRENGTH (3 << 5): indicate the drive strength of the pin using the 11 - High OUTPUT (1 << 7): indicate this pin need to be configured as an output. OUTPUT_VAL (1 << 8): output val (1 = high, 0 = low) +SLEWRATE (1 << 9): slew rate of the pin: 0 = disable, 1 = enable DEBOUNCE (1 << 16): indicate this pin needs debounce. DEBOUNCE_VAL (0x3fff << 17): debounce value. @@ -116,6 +117,19 @@ Some requirements for using atmel,at91rm9200-pinctrl binding: configurations by referring to the phandle of that pin configuration node. 4. The gpio controller must be describe in the pinctrl simple-bus. +For each bank the required properties are: +- compatible: "atmel,at91sam9x5-gpio" or "atmel,at91rm9200-gpio" or + "microchip,sam9x60-gpio" +- reg: physical base address and length of the controller's registers +- interrupts: interrupt outputs from the controller +- interrupt-controller: marks the device node as an interrupt controller +- #interrupt-cells: should be 2; refer to ../interrupt-controller/interrupts.txt + for more details. +- gpio-controller +- #gpio-cells: should be 2; the first cell is the GPIO number and the second + cell specifies GPIO flags as defined in <dt-bindings/gpio/gpio.h>. +- clocks: bank clock + Examples: pinctrl@fffff400 { @@ -125,6 +139,17 @@ pinctrl@fffff400 { compatible = "atmel,at91rm9200-pinctrl", "simple-bus"; reg = <0xfffff400 0x600>; + pioA: gpio@fffff400 { + compatible = "atmel,at91sam9x5-gpio"; + reg = <0xfffff400 0x200>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&pmc PMC_TYPE_PERIPHERAL 2>; + }; + atmel,mux-mask = < /* A B */ 0xffffffff 0xffc00c3b /* pioA */ diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx50-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx50-pinctrl.txt new file mode 100644 index 000000000000..6da01d619d33 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx50-pinctrl.txt @@ -0,0 +1,32 @@ +* Freescale IMX50 IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,imx50-iomuxc" +- fsl,pins: two integers array, represents a group of pins mux and config + setting. The format is fsl,pins = <PIN_FUNC_ID CONFIG>, PIN_FUNC_ID is a + pin working on a specific function, CONFIG is the pad setting value like + pull-up for this pin. Please refer to imx50 datasheet for the valid pad + config settings. + +CONFIG bits definition: +PAD_CTL_HVE (1 << 13) +PAD_CTL_HYS (1 << 8) +PAD_CTL_PKE (1 << 7) +PAD_CTL_PUE (1 << 6) +PAD_CTL_PUS_100K_DOWN (0 << 4) +PAD_CTL_PUS_47K_UP (1 << 4) +PAD_CTL_PUS_100K_UP (2 << 4) +PAD_CTL_PUS_22K_UP (3 << 4) +PAD_CTL_ODE (1 << 3) +PAD_CTL_DSE_LOW (0 << 1) +PAD_CTL_DSE_MED (1 << 1) +PAD_CTL_DSE_HIGH (2 << 1) +PAD_CTL_DSE_MAX (3 << 1) +PAD_CTL_SRE_FAST (1 << 0) +PAD_CTL_SRE_SLOW (0 << 0) + +Refer to imx50-pinfunc.h in device tree source folder for all available +imx50 PIN_FUNC_ID. diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt new file mode 100644 index 000000000000..524a16fca666 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx8mm-pinctrl.txt @@ -0,0 +1,36 @@ +* Freescale IMX8MM IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt and pinctrl-bindings.txt in this directory +for common binding part and usage. + +Required properties: +- compatible: "fsl,imx8mm-iomuxc" +- reg: should contain the base physical address and size of the iomuxc + registers. + +Required properties in sub-nodes: +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val + input_val> are specified using a PIN_FUNC_ID macro, which can be found in + <dt-bindings/pinctrl/imx8mm-pinfunc.h>. The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX8M Mini + Reference Manual for detailed CONFIG settings. + +Examples: + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; +}; + +iomuxc: pinctrl@30330000 { + compatible = "fsl,imx8mm-iomuxc"; + reg = <0x0 0x30330000 0x0 0x10000>; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt index c7c088d2dd50..38dc56a57760 100644 --- a/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt @@ -58,11 +58,11 @@ group pwm3 - functions pwm, gpio group pmic1 - - pin 17 + - pin 7 - functions pmic, gpio group pmic0 - - pin 16 + - pin 6 - functions pmic, gpio group i2c2 @@ -112,19 +112,31 @@ group usb2_drvvbus1 - functions drvbus, gpio group sdio_sb - - pins 60-64 + - pins 60-65 - functions sdio, gpio group rgmii - - pins 42-55 + - pins 42-53 - functions mii, gpio group pcie1 - - pins 39-40 + - pins 39 + - functions pcie, gpio + +group pcie1_clkreq + - pins 40 - functions pcie, gpio +group pcie1_wakeup + - pins 41 + - functions pcie, gpio + +group smi + - pins 54-55 + - functions smi, gpio + group ptp - - pins 56-58 + - pins 56 - functions ptp, gpio group ptp_clk diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt index 82ead40311f6..a47dd990a8d3 100644 --- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt @@ -23,11 +23,11 @@ The GPIO bank for the controller is represented as a sub-node and it acts as a GPIO controller. Required properties for sub-nodes are: - - reg: should contain address and size for mux, pull-enable, pull and - gpio register sets - - reg-names: an array of strings describing the "reg" entries. Must - contain "mux", "pull" and "gpio". "pull-enable" is optional and - when it is missing the "pull" registers are used instead + - reg: should contain a list of address and size, one tuple for each entry + in reg-names. + - reg-names: an array of strings describing the "reg" entries. + Must contain "mux" and "gpio". + May contain "pull", "pull-enable" and "ds" when appropriate. - gpio-controller: identifies the node as a gpio controller - #gpio-cells: must be 2 diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt index 759aa1732e48..7f64a7e92c28 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt @@ -19,6 +19,7 @@ PMIC's from Qualcomm. "qcom,pm8998-gpio" "qcom,pma8084-gpio" "qcom,pmi8994-gpio" + "qcom,pmi8998-gpio" "qcom,pms405-gpio" And must contain either "qcom,spmi-gpio" or "qcom,ssbi-gpio" diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt index 89871ab8c704..5c913d4cf36c 100644 --- a/Documentation/devicetree/bindings/power/supply/battery.txt +++ b/Documentation/devicetree/bindings/power/supply/battery.txt @@ -16,6 +16,7 @@ Required Properties: Optional Properties: - voltage-min-design-microvolt: drained battery voltage + - voltage-max-design-microvolt: fully charged battery voltage - energy-full-design-microwatt-hours: battery design energy - charge-full-design-microamp-hours: battery design capacity - precharge-current-microamp: current for pre-charge phase @@ -48,6 +49,7 @@ Example: bat: battery { compatible = "simple-battery"; voltage-min-design-microvolt = <3200000>; + voltage-max-design-microvolt = <4200000>; energy-full-design-microwatt-hours = <5290000>; charge-full-design-microamp-hours = <1430000>; precharge-current-microamp = <256000>; diff --git a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt index fc35ac577401..0a5705b8b592 100644 --- a/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt +++ b/Documentation/devicetree/bindings/power/supply/sc27xx-fg.txt @@ -9,8 +9,8 @@ Required properties: "sprd,sc2731-fgu". - reg: The address offset of fuel gauge unit. - battery-detect-gpios: GPIO for battery detection. -- io-channels: Specify the IIO ADC channel to get temperature. -- io-channel-names: Should be "bat-temp". +- io-channels: Specify the IIO ADC channels to get temperature and charge voltage. +- io-channel-names: Should be "bat-temp" or "charge-vol". - nvmem-cells: A phandle to the calibration cells provided by eFuse device. - nvmem-cell-names: Should be "fgu_calib". - monitored-battery: Phandle of battery characteristics devicetree node. @@ -47,8 +47,8 @@ Example: compatible = "sprd,sc2731-fgu"; reg = <0xa00>; battery-detect-gpios = <&pmic_eic 9 GPIO_ACTIVE_HIGH>; - io-channels = <&pmic_adc 5>; - io-channel-names = "bat-temp"; + io-channels = <&pmic_adc 5>, <&pmic_adc 14>; + io-channel-names = "bat-temp", "charge-vol"; nvmem-cells = <&fgu_calib>; nvmem-cell-names = "fgu_calib"; monitored-battery = <&bat>; diff --git a/Documentation/devicetree/bindings/property-units.txt b/Documentation/devicetree/bindings/property-units.txt index 45ce054d844d..bfd33734faca 100644 --- a/Documentation/devicetree/bindings/property-units.txt +++ b/Documentation/devicetree/bindings/property-units.txt @@ -31,6 +31,7 @@ Electricity -microwatt-hours: micro Watt-hours -microvolt : micro volts -picofarads : picofarads +-femtofarads : femtofarads Temperature ---------------------------------------- diff --git a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt index c8c831d7b0d1..591ecdd39c7b 100644 --- a/Documentation/devicetree/bindings/pwm/atmel-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/atmel-pwm.txt @@ -5,6 +5,7 @@ Required properties: - "atmel,at91sam9rl-pwm" - "atmel,sama5d3-pwm" - "atmel,sama5d2-pwm" + - "microchip,sam9x60-pwm" - reg: physical base address and length of the controller's registers - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. diff --git a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt index fa7849d67836..daedfef09bb6 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-hibvt.txt @@ -5,6 +5,8 @@ Required properties: The SoC specific strings supported including: "hisilicon,hi3516cv300-pwm" "hisilicon,hi3519v100-pwm" + "hisilicon,hi3559v100-shub-pwm" + "hisilicon,hi3559v100-pwm - reg: physical base address and length of the controller's registers. - clocks: phandle and clock specifier of the PWM reference clock. - resets: phandle and reset specifier for the PWM controller reset. diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt index a842a782b557..66af2c30944f 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp-pil.txt @@ -35,7 +35,7 @@ on the Qualcomm Technology Inc. ADSP Hexagon core. Value type: <stringlist> Definition: List of clock input name strings sorted in the same order as the clocks property. Definition must have - "xo", "sway_cbcr", "lpass_aon", "lpass_ahbs_aon_cbcr", + "xo", "sway_cbcr", "lpass_ahbs_aon_cbcr", "lpass_ahbm_aon_cbcr", "qdsp6ss_xo", "qdsp6ss_sleep" and "qdsp6ss_core". @@ -100,13 +100,12 @@ ADSP, as it is found on SDM845 boards. clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_LPASS_SWAY_CLK>, - <&lpasscc LPASS_AUDIO_WRAPPER_AON_CLK>, <&lpasscc LPASS_Q6SS_AHBS_AON_CLK>, <&lpasscc LPASS_Q6SS_AHBM_AON_CLK>, <&lpasscc LPASS_QDSP6SS_XO_CLK>, <&lpasscc LPASS_QDSP6SS_SLEEP_CLK>, <&lpasscc LPASS_QDSP6SS_CORE_CLK>; - clock-names = "xo", "sway_cbcr", "lpass_aon", + clock-names = "xo", "sway_cbcr", "lpass_ahbs_aon_cbcr", "lpass_ahbm_aon_cbcr", "qdsp6ss_xo", "qdsp6ss_sleep", "qdsp6ss_core"; diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt index 9c0cff3a5ed8..292dfda9770d 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt @@ -19,13 +19,30 @@ on the Qualcomm ADSP Hexagon core. - interrupts-extended: Usage: required Value type: <prop-encoded-array> - Definition: must list the watchdog, fatal IRQs ready, handover and - stop-ack IRQs + Definition: reference to the interrupts that match interrupt-names - interrupt-names: Usage: required Value type: <stringlist> - Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack" + Definition: The interrupts needed depends on the compatible + string: + qcom,msm8974-adsp-pil: + qcom,msm8996-adsp-pil: + qcom,msm8996-slpi-pil: + qcom,qcs404-adsp-pas: + qcom,qcs404-cdsp-pas: + qcom,sdm845-adsp-pas: + qcom,sdm845-cdsp-pas: + must be "wdog", "fatal", "ready", "handover", "stop-ack" + qcom,qcs404-wcss-pas: + must be "wdog", "fatal", "ready", "handover", "stop-ack", + "shutdown-ack" + +- firmware-name: + Usage: optional + Value type: <string> + Definition: must list the relative firmware image path for the + Hexagon Core. - clocks: Usage: required diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt index 9ff5b0309417..41ca5df5be5a 100644 --- a/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt +++ b/Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt @@ -28,24 +28,51 @@ on the Qualcomm Hexagon core. - interrupts-extended: Usage: required Value type: <prop-encoded-array> - Definition: must list the watchdog, fatal IRQs ready, handover and - stop-ack IRQs + Definition: reference to the interrupts that match interrupt-names - interrupt-names: Usage: required Value type: <stringlist> - Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack" + Definition: The interrupts needed depends on the the compatible + string: + qcom,q6v5-pil: + qcom,ipq8074-wcss-pil: + qcom,msm8916-mss-pil: + qcom,msm8974-mss-pil: + must be "wdog", "fatal", "ready", "handover", "stop-ack" + qcom,msm8996-mss-pil: + qcom,sdm845-mss-pil: + must be "wdog", "fatal", "ready", "handover", "stop-ack", + "shutdown-ack" + +- firmware-name: + Usage: optional + Value type: <stringlist> + Definition: must list the relative firmware image paths for mba and + modem. They are used for booting and authenticating the + Hexagon core. - clocks: Usage: required Value type: <phandle> - Definition: reference to the iface, bus and mem clocks to be held on - behalf of the booting of the Hexagon core + Definition: reference to the clocks that match clock-names - clock-names: Usage: required Value type: <stringlist> - Definition: must be "iface", "bus", "mem" + Definition: The clocks needed depend on the compatible string: + qcom,ipq8074-wcss-pil: + no clock names required + qcom,q6v5-pil: + qcom,msm8916-mss-pil: + qcom,msm8974-mss-pil: + must be "iface", "bus", "mem", "xo" + qcom,msm8996-mss-pil: + must be "iface", "bus", "mem", "xo", "gpll0_mss", + "snoc_axi", "mnoc_axi", "pnoc", "qdss" + qcom,sdm845-mss-pil: + must be "iface", "bus", "mem", "xo", "gpll0_mss", + "snoc_axi", "mnoc_axi", "prng" - resets: Usage: required @@ -65,6 +92,19 @@ on the Qualcomm Hexagon core. must be "mss_restart", "pdc_reset" for the modem sub-system on SDM845 SoCs +For the compatible strings below the following supplies are required: + "qcom,q6v5-pil" + "qcom,msm8916-mss-pil", +- cx-supply: +- mx-supply: +- pll-supply: + Usage: required + Value type: <phandle> + Definition: reference to the regulators to be held on behalf of the + booting of the Hexagon core + +For the compatible string below the following supplies are required: + "qcom,msm8974-mss-pil" - cx-supply: - mss-supply: - mx-supply: @@ -74,6 +114,33 @@ on the Qualcomm Hexagon core. Definition: reference to the regulators to be held on behalf of the booting of the Hexagon core +For the compatible string below the following supplies are required: + "qcom,msm8996-mss-pil" +- pll-supply: + Usage: required + Value type: <phandle> + Definition: reference to the regulators to be held on behalf of the + booting of the Hexagon core + +- power-domains: + Usage: required + Value type: <phandle> + Definition: reference to power-domains that match power-domain-names + +- power-domain-names: + Usage: required + Value type: <stringlist> + Definition: The power-domains needed depend on the compatible string: + qcom,q6v5-pil: + qcom,ipq8074-wcss-pil: + qcom,msm8916-mss-pil: + qcom,msm8974-mss-pil: + no power-domain names required + qcom,msm8996-mss-pil: + must be "cx", "mx" + qcom,sdm845-mss-pil: + must be "cx", "mx", "mss", "load_state" + - qcom,smem-states: Usage: required Value type: <phandle> diff --git a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt index 18b892d010d8..2405e35a1bc0 100644 --- a/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt +++ b/Documentation/devicetree/bindings/rtc/abracon,abx80x.txt @@ -16,6 +16,7 @@ Required properties: "abracon,ab1803" "abracon,ab1804" "abracon,ab1805" + "microcrystal,rv1805" Using "abracon,abx80x" will enable chip autodetection. - "reg": I2C bus address of the device diff --git a/Documentation/devicetree/bindings/rtc/cdns,rtc.txt b/Documentation/devicetree/bindings/rtc/cdns,rtc.txt new file mode 100644 index 000000000000..14a04487b432 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/cdns,rtc.txt @@ -0,0 +1,25 @@ +Cadence Real Time Clock + +The Cadence RTC controller with date, time and alarm capabilities. +The alarm may wake the system from low-power state. + +Required properties: +- compatible: Should be "cdns,rtc-r109v3" +- reg: Specifies base physical address and size of the register area. +- interrupts: A single interrupt specifier. +- clocks: Must contain two entries: + - pclk: APB registers clock + - ref_clk: reference 1Hz or 100Hz clock, depending on IP configuration + See ../clocks/clock-bindings.txt for details. + +Example: + rtc0: rtc@fd080000 { + compatible = "cdns,rtc-r109v3"; + reg = <0xfd080000 0x1000>; + + clock-names = "pclk", "ref_clk"; + clocks = <&sysclock>, <&refclock>; + + interrupt-parent = <&gic>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/rtc/isil,isl1208.txt b/Documentation/devicetree/bindings/rtc/isil,isl1208.txt new file mode 100644 index 000000000000..51f003006f04 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/isil,isl1208.txt @@ -0,0 +1,38 @@ +Intersil ISL1209/19 I2C RTC/Alarm chip with event in + +ISL12X9 have additional pins EVIN and #EVDET for tamper detection, while the +ISL1208 and ISL1218 do not. They are all use the same driver with the bindings +described here, with chip specific properties as noted. + +Required properties supported by the device: + - "compatible": Should be one of the following: + - "isil,isl1208" + - "isil,isl1209" + - "isil,isl1218" + - "isil,isl1219" + - "reg": I2C bus address of the device + +Optional properties: + - "interrupt-names": list which may contains "irq" and "evdet" + evdet applies to isl1209 and isl1219 only + - "interrupts": list of interrupts for "irq" and "evdet" + evdet applies to isl1209 and isl1219 only + - "isil,ev-evienb": Enable or disable internal pull on EVIN pin + Applies to isl1209 and isl1219 only + Possible values are 0 and 1 + Value 0 enables internal pull-up on evin pin, 1 disables it. + Default will leave the non-volatile configuration of the pullup + as is. + +Example isl1219 node with #IRQ pin connected to SoC gpio1 pin12 and #EVDET pin +connected to SoC gpio2 pin 24 and internal pull-up enabled in EVIN pin. + + isl1219: rtc@68 { + compatible = "isil,isl1219"; + reg = <0x68>; + interrupt-names = "irq", "evdet"; + interrupts-extended = <&gpio1 12 IRQ_TYPE_EDGE_FALLING>, + <&gpio2 24 IRQ_TYPE_EDGE_FALLING>; + isil,ev-evienb = <1>; + }; + diff --git a/Documentation/devicetree/bindings/rtc/isil,isl1219.txt b/Documentation/devicetree/bindings/rtc/isil,isl1219.txt deleted file mode 100644 index c3efd48e91c2..000000000000 --- a/Documentation/devicetree/bindings/rtc/isil,isl1219.txt +++ /dev/null @@ -1,29 +0,0 @@ -Intersil ISL1219 I2C RTC/Alarm chip with event in - -ISL1219 has additional pins EVIN and #EVDET for tamper detection. - -Required properties supported by the device: - - - "compatible": must be "isil,isl1219" - - "reg": I2C bus address of the device - -Optional properties: - - - "interrupt-names": list which may contains "irq" and "evdet" - - "interrupts": list of interrupts for "irq" and "evdet" - - "isil,ev-evienb": if present EV.EVIENB bit is set to the specified - value for proper operation. - - -Example isl1219 node with #IRQ pin connected to SoC gpio1 pin12 - and #EVDET pin connected to SoC gpio2 pin 24: - - isl1219: rtc@68 { - compatible = "isil,isl1219"; - reg = <0x68>; - interrupt-names = "irq", "evdet"; - interrupts-extended = <&gpio1 12 IRQ_TYPE_EDGE_FALLING>, - <&gpio2 24 IRQ_TYPE_EDGE_FALLING>; - isil,ev-evienb = <1>; - }; - diff --git a/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt b/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt new file mode 100644 index 000000000000..d3e380ad712d --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/nxp,pcf85063.txt @@ -0,0 +1,18 @@ +* NXP PCF85063 Real Time Clock + +Required properties: +- compatible: Should contain "nxp,pcf85063". +- reg: I2C address for chip. + +Optional property: +- quartz-load-femtofarads: The capacitive load of the quartz(x-tal), + expressed in femto Farad (fF). Valid values are 7000 and 12500. + Default value (if no value is specified) is 7000fF. + +Example: + +pcf85063: rtc@51 { + compatible = "nxp,pcf85063"; + reg = <0x51>; + quartz-load-femtofarads = <12500>; +}; diff --git a/Documentation/devicetree/bindings/rtc/nxp,pcf8523.txt b/Documentation/devicetree/bindings/rtc/nxp,pcf8523.txt new file mode 100644 index 000000000000..0b1080c60f63 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/nxp,pcf8523.txt @@ -0,0 +1,18 @@ +* NXP PCF8523 Real Time Clock + +Required properties: +- compatible: Should contain "nxp,pcf8523". +- reg: I2C address for chip. + +Optional property: +- quartz-load-femtofarads: The capacitive load of the quartz(x-tal), + expressed in femto Farad (fF). Valid values are 7000 and 12500. + Default value (if no value is specified) is 12500fF. + +Example: + +pcf8523: rtc@68 { + compatible = "nxp,pcf8523"; + reg = <0x68>; + quartz-load-femtofarads = <7000>; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-meson.txt b/Documentation/devicetree/bindings/rtc/rtc-meson.txt new file mode 100644 index 000000000000..e921fe66a362 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-meson.txt @@ -0,0 +1,35 @@ +* Amlogic Meson6, Meson8, Meson8b and Meson8m2 RTC + +Required properties: +- compatible: should be one of the following describing the hardware: + * "amlogic,meson6-rtc" + * "amlogic,meson8-rtc" + * "amlogic,meson8b-rtc" + * "amlogic,meson8m2-rtc" + +- reg: physical register space for the controller's memory mapped registers. +- interrupts: the interrupt line of the RTC block. +- clocks: reference to the external 32.768kHz crystal oscillator. +- vdd-supply: reference to the power supply of the RTC block. +- resets: reset controller reference to allow reset of the controller + +Optional properties for the battery-backed non-volatile memory: +- #address-cells: should be 1 to address the battery-backed non-volatile memory +- #size-cells: should be 1 to reference the battery-backed non-volatile memory + +Optional child nodes: +- see ../nvmem/nvmem.txt + +Example: + + rtc: rtc@740 { + compatible = "amlogic,meson6-rtc"; + reg = <0x740 0x14>; + interrupts = <GIC_SPI 72 IRQ_TYPE_EDGE_RISING>; + clocks = <&rtc32k_xtal>; + vdd-supply = <&rtc_vdd>; + resets = <&reset RESET_RTC>; + + #address-cells = <1>; + #size-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/rtc/rtc.txt b/Documentation/devicetree/bindings/rtc/rtc.txt index 7c8da6926095..f4687c68c08c 100644 --- a/Documentation/devicetree/bindings/rtc/rtc.txt +++ b/Documentation/devicetree/bindings/rtc/rtc.txt @@ -21,12 +21,16 @@ Optional properties The following properties may not be supported by all drivers. However, if a driver wants to support one of the below features, it should adapt the bindings below. -- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given - if trickle charger should be enabled -- trickle-diode-disable : Do not use internal trickle charger diode Should be - given if internal trickle charger diode should be - disabled -- wakeup-source : Enables wake up of host system on alarm +- trickle-resistor-ohms : Selected resistor for trickle charger. Should be given + if trickle charger should be enabled +- trickle-diode-disable : Do not use internal trickle charger diode Should be + given if internal trickle charger diode should be + disabled +- wakeup-source : Enables wake up of host system on alarm +- quartz-load-femtofarads : The capacitive load of the quartz(x-tal), + expressed in femto Farad (fF). + The default value shall be listed (if optional), + and likewise all valid values. Trivial RTCs ------------ @@ -39,21 +43,23 @@ possibly an interrupt line. Compatible Vendor / Chip ========== ============= abracon,abb5zes3 AB-RTCMC-32.768kHz-B5ZE-S3: Real Time Clock/Calendar Module with I2C Interface +abracon,abeoz9 AB-RTCMC-32.768kHz-EOZ9: Real Time Clock/Calendar Module with I2C Interface dallas,ds1374 I2C, 32-Bit Binary Counter Watchdog RTC with Trickle Charger and Reset Input/Output dallas,ds1672 Dallas DS1672 Real-time Clock dallas,ds3232 Extremely Accurate I²C RTC with Integrated Crystal and SRAM epson,rx8010 I2C-BUS INTERFACE REAL TIME CLOCK MODULE +epson,rx8571 I2C-BUS INTERFACE REAL TIME CLOCK MODULE with Battery Backed RAM epson,rx8581 I2C-BUS INTERFACE REAL TIME CLOCK MODULE emmicro,em3027 EM Microelectronic EM3027 Real-time Clock isil,isl1208 Intersil ISL1208 Low Power RTC with Battery Backed SRAM isil,isl1218 Intersil ISL1218 Low Power RTC with Battery Backed SRAM isil,isl12022 Intersil ISL12022 Real-time Clock +microcrystal,rv3028 Real Time Clock Module with I2C-Bus microcrystal,rv3029 Real Time Clock Module with I2C-Bus +microcrystal,rv8523 Real Time Clock nxp,pcf2127 Real-time clock nxp,pcf2129 Real-time clock -nxp,pcf8523 Real-time Clock nxp,pcf8563 Real-time clock/calendar -nxp,pcf85063 Tiny Real-Time Clock pericom,pt7c4338 Real-time Clock Module ricoh,r2025sd I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,r2221tl I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC @@ -62,3 +68,4 @@ ricoh,rs5c372b I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c386 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC ricoh,rv5c387a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC sii,s35390a 2-wire CMOS real-time clock +whwave,sd3078 I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index 742cb470595b..bcfb13194f16 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -16,6 +16,7 @@ Required properties: * "mediatek,mt8127-uart" for MT8127 compatible UARTS * "mediatek,mt8135-uart" for MT8135 compatible UARTS * "mediatek,mt8173-uart" for MT8173 compatible UARTS + * "mediatek,mt8183-uart", "mediatek,mt6577-uart" for MT8183 compatible UARTS * "mediatek,mt6577-uart" for MT6577 and all of the above - reg: The base address of the UART register bank. diff --git a/Documentation/devicetree/bindings/thermal/brcm,sr-thermal.txt b/Documentation/devicetree/bindings/thermal/brcm,sr-thermal.txt new file mode 100644 index 000000000000..3ab330219d45 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/brcm,sr-thermal.txt @@ -0,0 +1,105 @@ +* Broadcom Stingray Thermal + +This binding describes thermal sensors that is part of Stingray SoCs. + +Required properties: +- compatible : Must be "brcm,sr-thermal" +- reg : Memory where tmon data will be available. +- brcm,tmon-mask: A one cell bit mask of valid TMON sources. + Each bit represents single TMON source. +- #thermal-sensor-cells : Thermal sensor phandler +- polling-delay: Max number of milliseconds to wait between polls. +- thermal-sensors: A list of thermal sensor phandles and specifier. + specifier value is tmon ID and it should be + in correspond with brcm,tmon-mask. +- temperature: trip temperature threshold in millicelsius. + +Example: + tmons { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x8f100000 0x100>; + + tmon: tmon@0 { + compatible = "brcm,sr-thermal"; + reg = <0x0 0x40>; + brcm,tmon-mask = <0x3f>; + #thermal-sensor-cells = <1>; + }; + }; + + thermal-zones { + ihost0_thermal: ihost0-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 0>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + ihost1_thermal: ihost1-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 1>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + ihost2_thermal: ihost2-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 2>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + ihost3_thermal: ihost3-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 3>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + crmu_thermal: crmu-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 4>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + nitro_thermal: nitro-thermal { + polling-delay-passive = <0>; + polling-delay = <1000>; + thermal-sensors = <&tmon 5>; + trips { + cpu-crit { + temperature = <105000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt index 41d6a443ad66..f8d7831f3974 100644 --- a/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/mediatek-thermal.txt @@ -13,6 +13,7 @@ Required properties: - "mediatek,mt2701-thermal" : For MT2701 family of SoCs - "mediatek,mt2712-thermal" : For MT2712 family of SoCs - "mediatek,mt7622-thermal" : For MT7622 SoC + - "mediatek,mt8183-thermal" : For MT8183 family of SoCs - reg: Address range of the thermal controller - interrupts: IRQ for the thermal controller - clocks, clock-names: Clocks needed for the thermal controller. required diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt index a48c44817367..0b83df1a5418 100644 --- a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt @@ -6,9 +6,10 @@ Each UFS Host Controller should have its own node. Required properties: - compatible : compatible list, contains one of the following - "hisilicon,hi3660-ufs", "jedec,ufs-1.1" for hisi ufs - host controller present on Hi36xx chipset. + host controller present on Hi3660 chipset. + "hisilicon,hi3670-ufs", "jedec,ufs-2.1" for hisi ufs + host controller present on Hi3670 chipset. - reg : should contain UFS register address space & UFS SYS CTRL register address, -- interrupt-parent : interrupt device - interrupts : interrupt number - clocks : List of phandle and clock specifier pairs - clock-names : List of clock input name strings sorted in the same diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt index 8cf59452c675..5111e9130bc3 100644 --- a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -4,11 +4,14 @@ UFSHC nodes are defined to describe on-chip UFS host controllers. Each UFS controller instance should have its own node. Required properties: -- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0", may - also list one or more of the following: - "qcom,msm8994-ufshc" - "qcom,msm8996-ufshc" - "qcom,ufshc" +- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0" + + For Qualcomm SoCs must contain, as below, an + SoC-specific compatible along with "qcom,ufshc" and + the appropriate jedec string: + "qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0" + "qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0" + "qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0" - interrupts : <interrupt mapping for UFS host controller IRQ> - reg : <registers mapping> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 98f83edbfc95..8162b0eb4b50 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -140,11 +140,13 @@ fairphone Fairphone B.V. faraday Faraday Technology Corporation fastrax Fastrax Oy fcs Fairchild Semiconductor +feiyang Shenzhen Fly Young Technology Co.,LTD. firefly Firefly focaltech FocalTech Systems Co.,Ltd friendlyarm Guangzhou FriendlyARM Computer Tech Co., Ltd fsl Freescale Semiconductor fujitsu Fujitsu Ltd. +gateworks Gateworks Corporation gcw Game Consoles Worldwide ge General Electric Company geekbuying GeekBuying @@ -399,6 +401,7 @@ tcl Toby Churchill Ltd. technexion TechNexion technologic Technologic Systems tempo Tempo Semiconductor +techstar Shenzhen Techstar Electronics Co., Ltd. terasic Terasic Inc. thine THine Electronics, Inc. ti Texas Instruments @@ -439,6 +442,7 @@ vot Vision Optical Technology Co., Ltd. wd Western Digital Corp. wetek WeTek Electronics, limited. wexler Wexler +whwave Shenzhen whwave Electronics, Inc. wi2wi Wi2Wi, Inc. winbond Winbond Electronics corp. winstar Winstar Display Corp. diff --git a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt index ef2b97b72e08..9f365c1a3399 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas-wdt.txt @@ -8,6 +8,7 @@ Required properties: - "renesas,r8a7743-wdt" (RZ/G1M) - "renesas,r8a7744-wdt" (RZ/G1N) - "renesas,r8a7745-wdt" (RZ/G1E) + - "renesas,r8a77470-wdt" (RZ/G1C) - "renesas,r8a774a1-wdt" (RZ/G2M) - "renesas,r8a774c0-wdt" (RZ/G2E) - "renesas,r8a7790-wdt" (R-Car H2) diff --git a/Documentation/devicetree/bindings/watchdog/st,stpmic1-wdt.txt b/Documentation/devicetree/bindings/watchdog/st,stpmic1-wdt.txt new file mode 100644 index 000000000000..7cc1407f15cb --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/st,stpmic1-wdt.txt @@ -0,0 +1,11 @@ +STMicroelectronics STPMIC1 Watchdog + +Required properties: + +- compatible : should be "st,stpmic1-wdt" + +Example: + +watchdog { + compatible = "st,stpmic1-wdt"; +}; |
