diff options
Diffstat (limited to 'Documentation/devicetree')
8 files changed, 76 insertions, 6 deletions
diff --git a/Documentation/devicetree/bindings/arm/exynos/power_domain.txt b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt new file mode 100644 index 000000000000..6528e215c5fe --- /dev/null +++ b/Documentation/devicetree/bindings/arm/exynos/power_domain.txt @@ -0,0 +1,21 @@ +* Samsung Exynos Power Domains + +Exynos processors include support for multiple power domains which are used +to gate power to one or more peripherals on the processor. + +Required Properties: +- compatiable: should be one of the following. + * samsung,exynos4210-pd - for exynos4210 type power domain. +- reg: physical base address of the controller and length of memory mapped + region. + +Optional Properties: +- samsung,exynos4210-pd-off: Specifies that the power domain is in turned-off + state during boot and remains to be turned-off until explicitly turned-on. + +Example: + + lcd0: power-domain-lcd0 { + compatible = "samsung,exynos4210-pd"; + reg = <0x10023C00 0x10>; + }; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index dbdab40ed3a6..e78e8bccac30 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -5,7 +5,7 @@ IPs present in the SoC. On top of that an omap_device is created to extend the platform_device capabilities and to allow binding with one or several hwmods. The hwmods will contain all the information to build the device: -adresse range, irq lines, dma lines, interconnect, PRCM register, +address range, irq lines, dma lines, interconnect, PRCM register, clock domain, input clocks. For the moment just point to the existing hwmod, the next step will be to move data from hwmod to device-tree representation. @@ -41,3 +41,9 @@ Boards: - OMAP4 PandaBoard : Low cost community board compatible = "ti,omap4-panda", "ti,omap4430" + +- OMAP3 EVM : Software Developement Board for OMAP35x, AM/DM37x + compatible = "ti,omap3-evm", "ti,omap3" + +- AM335X EVM : Software Developement Board for AM335x + compatible = "ti,am335x-evm", "ti,am33xx", "ti,omap3" diff --git a/Documentation/devicetree/bindings/arm/sirf.txt b/Documentation/devicetree/bindings/arm/sirf.txt index 6b07f65b32de..1881e1c6dda5 100644 --- a/Documentation/devicetree/bindings/arm/sirf.txt +++ b/Documentation/devicetree/bindings/arm/sirf.txt @@ -1,3 +1,3 @@ -prima2 "cb" evalutation board +prima2 "cb" evaluation board Required root node properties: - compatible = "sirf,prima2-cb", "sirf,prima2"; diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt index 141087cf3107..fd2bd56e7195 100644 --- a/Documentation/devicetree/bindings/gpio/led.txt +++ b/Documentation/devicetree/bindings/gpio/led.txt @@ -7,9 +7,9 @@ Each LED is represented as a sub-node of the gpio-leds device. Each node's name represents the name of the corresponding LED. LED sub-node properties: -- gpios : Should specify the LED's GPIO, see "Specifying GPIO information - for devices" in Documentation/devicetree/booting-without-of.txt. Active - low LEDs should be indicated using flags in the GPIO specifier. +- gpios : Should specify the LED's GPIO, see "gpios property" in + Documentation/devicetree/gpio.txt. Active low LEDs should be + indicated using flags in the GPIO specifier. - label : (optional) The label for this LED. If omitted, the label is taken from the node name (excluding the unit address). - linux,default-trigger : (optional) This parameter, if present, is a diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt new file mode 100644 index 000000000000..1f62623f8c3f --- /dev/null +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -0,0 +1,28 @@ +* STMicroelectronics 10/100/1000 Ethernet driver (GMAC) + +Required properties: +- compatible: Should be "st,spear600-gmac" +- reg: Address and length of the register set for the device +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the STMMAC interrupts +- interrupt-names: Should contain the interrupt names "macirq" + "eth_wake_irq" if this interrupt is supported in the "interrupts" + property +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "mii", "rmii", "gmii", "rgmii". + +Optional properties: +- mac-address: 6 bytes, mac address + +Examples: + + gmac0: ethernet@e0800000 { + compatible = "st,spear600-gmac"; + reg = <0xe0800000 0x8000>; + interrupt-parent = <&vic1>; + interrupts = <24 23>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "gmii"; + }; diff --git a/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt new file mode 100644 index 000000000000..6588b6950a7f --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/efm32-uart.txt @@ -0,0 +1,14 @@ +* Energymicro efm32 UART + +Required properties: +- compatible : Should be "efm32,uart" +- reg : Address and length of the register set +- interrupts : Should contain uart interrupt + +Example: + +uart@0x4000c400 { + compatible = "efm32,uart"; + reg = <0x4000c400 0x400>; + interrupts = <15>; +}; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index ecc6a6cd26c1..a20008ab319a 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -30,6 +30,7 @@ national National Semiconductor nintendo Nintendo nvidia NVIDIA nxp NXP Semiconductors +picochip Picochip Ltd powervr Imagination Technologies qcom Qualcomm, Inc. ramtron Ramtron International diff --git a/Documentation/devicetree/booting-without-of.txt b/Documentation/devicetree/booting-without-of.txt index 7c1329de0596..da0bfeb4253d 100644 --- a/Documentation/devicetree/booting-without-of.txt +++ b/Documentation/devicetree/booting-without-of.txt @@ -169,7 +169,7 @@ it with special cases. b) Entry with a flattened device-tree block. Firmware loads the physical address of the flattened device tree block (dtb) into r2, - r1 is not used, but it is considered good practise to use a valid + r1 is not used, but it is considered good practice to use a valid machine number as described in Documentation/arm/Booting. r0 : 0 |
