diff options
Diffstat (limited to 'Documentation/devicetree')
9 files changed, 282 insertions, 36 deletions
diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt index bf99e2f24788..205593f56fe7 100644 --- a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt +++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.txt @@ -16,6 +16,11 @@ Required properties: - vref-supply: The regulator supply ADC reference voltage. - #io-channel-cells: Should be 1, see ../iio-bindings.txt +Optional properties: +- resets: Must contain an entry for each entry in reset-names if need support + this option. See ../reset/reset.txt for details. +- reset-names: Must include the name "saradc-apb". + Example: saradc: saradc@2006c000 { compatible = "rockchip,saradc"; @@ -23,6 +28,8 @@ Example: interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clocks = <&cru SCLK_SARADC>, <&cru PCLK_SARADC>; clock-names = "saradc", "apb_pclk"; + resets = <&cru SRST_SARADC>; + reset-names = "saradc-apb"; #io-channel-cells = <1>; vref-supply = <&vcc18>; }; diff --git a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt index 1112e0d794e1..820fee4b77b6 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/silead_gsl1680.txt @@ -13,6 +13,7 @@ Required properties: - touchscreen-size-y : See touchscreen.txt Optional properties: +- firmware-name : File basename (string) for board specific firmware - touchscreen-inverted-x : See touchscreen.txt - touchscreen-inverted-y : See touchscreen.txt - touchscreen-swapped-x-y : See touchscreen.txt diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 88faa91125bf..3cd4c43a3260 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -10,7 +10,7 @@ Required properties: subsystem (mmcss) inside the FlashSS (available in STiH407 SoC family). -- clock-names: Should be "mmc". +- clock-names: Should be "mmc" and "icn". (NB: The latter is not compulsory) See: Documentation/devicetree/bindings/resource-names.txt - clocks: Phandle to the clock. See: Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/serial/8250.txt b/Documentation/devicetree/bindings/serial/8250.txt index f5561ac7e17e..936ab5b87324 100644 --- a/Documentation/devicetree/bindings/serial/8250.txt +++ b/Documentation/devicetree/bindings/serial/8250.txt @@ -42,9 +42,6 @@ Optional properties: - auto-flow-control: one way to enable automatic flow control support. The driver is allowed to detect support for the capability even without this property. -- {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD - line respectively. It will use specified GPIO instead of the peripheral - function pin for the UART feature. If unsure, don't specify this property. Note: * fsl,ns16550: @@ -66,19 +63,3 @@ Example: interrupts = <10>; reg-shift = <2>; }; - -Example for OMAP UART using GPIO-based modem control signals: - - uart4: serial@49042000 { - compatible = "ti,omap3-uart"; - reg = <0x49042000 0x400>; - interrupts = <80>; - ti,hwmods = "uart4"; - clock-frequency = <48000000>; - cts-gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; - rts-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; - dtr-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; - dsr-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; - dcd-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; - rng-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; - }; diff --git a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt index 6f6c2f8e908d..0741dff048dd 100644 --- a/Documentation/devicetree/bindings/sound/omap-mcpdm.txt +++ b/Documentation/devicetree/bindings/sound/omap-mcpdm.txt @@ -8,8 +8,6 @@ Required properties: - interrupts: Interrupt number for McPDM - interrupt-parent: The parent interrupt controller - ti,hwmods: Name of the hwmod associated to the McPDM -- clocks: phandle for the pdmclk provider, likely <&twl6040> -- clock-names: Must be "pdmclk" Example: @@ -21,11 +19,3 @@ mcpdm: mcpdm@40132000 { interrupt-parent = <&gic>; ti,hwmods = "mcpdm"; }; - -In board DTS file the pdmclk needs to be added: - -&mcpdm { - clocks = <&twl6040>; - clock-names = "pdmclk"; - status = "okay"; -}; diff --git a/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt new file mode 100644 index 000000000000..ad7ac80a3841 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/brcm,spi-bcm-qspi.txt @@ -0,0 +1,233 @@ +Broadcom SPI controller + +The Broadcom SPI controller is a SPI master found on various SOCs, including +BRCMSTB (BCM7XXX), Cygnus, NSP and NS2. The Broadcom Master SPI hw IP consits +of : + MSPI : SPI master controller can read and write to a SPI slave device + BSPI : Broadcom SPI in combination with the MSPI hw IP provides acceleration + for flash reads and be configured to do single, double, quad lane + io with 3-byte and 4-byte addressing support. + + Supported Broadcom SoCs have one instance of MSPI+BSPI controller IP. + MSPI master can be used wihout BSPI. BRCMSTB SoCs have an additional instance + of a MSPI master without the BSPI to use with non flash slave devices that + use SPI protocol. + +Required properties: + +- #address-cells: + Must be <1>, as required by generic SPI binding. + +- #size-cells: + Must be <0>, also as required by generic SPI binding. + +- compatible: + Must be one of : + "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-qspi" : MSPI+BSPI on BRCMSTB SoCs + "brcm,spi-bcm-qspi", "brcm,spi-brcmstb-mspi" : Second Instance of MSPI + BRCMSTB SoCs + "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi" : MSPI+BSPI on Cygnus, NSP + "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi" : NS2 SoCs + +- reg: + Define the bases and ranges of the associated I/O address spaces. + The required range is MSPI controller registers. + +- reg-names: + First name does not matter, but must be reserved for the MSPI controller + register range as mentioned in 'reg' above, and will typically contain + - "bspi_regs": BSPI register range, not required with compatible + "spi-brcmstb-mspi" + - "mspi_regs": MSPI register range is required for compatible strings + - "intr_regs", "intr_status_reg" : Interrupt and status register for + NSP, NS2, Cygnus SoC + +- interrupts + The interrupts used by the MSPI and/or BSPI controller. + +- interrupt-names: + Names of interrupts associated with MSPI + - "mspi_halted" : + - "mspi_done": Indicates that the requested SPI operation is complete. + - "spi_lr_fullness_reached" : Linear read BSPI pipe full + - "spi_lr_session_aborted" : Linear read BSPI pipe aborted + - "spi_lr_impatient" : Linear read BSPI requested when pipe empty + - "spi_lr_session_done" : Linear read BSPI session done + +- clocks: + A phandle to the reference clock for this block. + +Optional properties: + + +- native-endian + Defined when using BE SoC and device uses BE register read/write + +Recommended optional m25p80 properties: +- spi-rx-bus-width: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Examples: + +BRCMSTB SoC Example: + + SPI Master (MSPI+BSPI) for SPI-NOR access: + + spi@f03e3400 { + #address-cells = <0x1>; + #size-cells = <0x0>; + compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-qspi"; + reg = <0xf03e0920 0x4 0xf03e3400 0x188 0xf03e3200 0x50>; + reg-names = "cs_reg", "mspi", "bspi"; + interrupts = <0x6 0x5 0x4 0x3 0x2 0x1 0x0>; + interrupt-parent = <0x1c>; + interrupt-names = "mspi_halted", + "mspi_done", + "spi_lr_overread", + "spi_lr_session_done", + "spi_lr_impatient", + "spi_lr_session_aborted", + "spi_lr_fullness_reached"; + + clocks = <&hif_spi>; + clock-names = "sw_spi"; + + m25p80@0 { + #size-cells = <0x2>; + #address-cells = <0x2>; + compatible = "m25p80"; + reg = <0x0>; + spi-max-frequency = <0x2625a00>; + spi-cpol; + spi-cpha; + m25p,fast-read; + + flash0.bolt@0 { + reg = <0x0 0x0 0x0 0x100000>; + }; + + flash0.macadr@100000 { + reg = <0x0 0x100000 0x0 0x10000>; + }; + + flash0.nvram@110000 { + reg = <0x0 0x110000 0x0 0x10000>; + }; + + flash0.kernel@120000 { + reg = <0x0 0x120000 0x0 0x400000>; + }; + + flash0.devtree@520000 { + reg = <0x0 0x520000 0x0 0x10000>; + }; + + flash0.splash@530000 { + reg = <0x0 0x530000 0x0 0x80000>; + }; + + flash0@0 { + reg = <0x0 0x0 0x0 0x4000000>; + }; + }; + }; + + + MSPI master for any SPI device : + + spi@f0416000 { + #address-cells = <1>; + #size-cells = <0>; + clocks = <&upg_fixed>; + compatible = "brcm,spi-brcmstb-qspi", "brcm,spi-brcmstb-mspi"; + reg = <0xf0416000 0x180>; + reg-names = "mspi"; + interrupts = <0x14>; + interrupt-parent = <&irq0_aon_intc>; + interrupt-names = "mspi_done"; + }; + +iProc SoC Example: + + qspi: spi@18027200 { + compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi"; + reg = <0x18027200 0x184>, + <0x18027000 0x124>, + <0x1811c408 0x004>, + <0x180273a0 0x01c>; + reg-names = "mspi_regs", "bspi_regs", "intr_regs", "intr_status_reg"; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = + "spi_lr_fullness_reached", + "spi_lr_session_aborted", + "spi_lr_impatient", + "spi_lr_session_done", + "mspi_done", + "mspi_halted"; + clocks = <&iprocmed>; + clock-names = "iprocmed"; + num-cs = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + + NS2 SoC Example: + + qspi: spi@66470200 { + compatible = "brcm,spi-bcm-qspi", "brcm,spi-ns2-qspi"; + reg = <0x66470200 0x184>, + <0x66470000 0x124>, + <0x67017408 0x004>, + <0x664703a0 0x01c>; + reg-names = "mspi", "bspi", "intr_regs", + "intr_status_reg"; + interrupts = <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "spi_l1_intr"; + clocks = <&iprocmed>; + clock-names = "iprocmed"; + num-cs = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + + + m25p80 node for NSP, NS2 + + &qspi { + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p80"; + reg = <0x0>; + spi-max-frequency = <12500000>; + m25p,fast-read; + spi-cpol; + spi-cpha; + + partition@0 { + label = "boot"; + reg = <0x00000000 0x000a0000>; + }; + + partition@a0000 { + label = "env"; + reg = <0x000a0000 0x00060000>; + }; + + partition@100000 { + label = "system"; + reg = <0x00100000 0x00600000>; + }; + + partition@700000 { + label = "rootfs"; + reg = <0x00700000 0x01900000>; + }; + }; diff --git a/Documentation/devicetree/bindings/spi/jcore,spi.txt b/Documentation/devicetree/bindings/spi/jcore,spi.txt new file mode 100644 index 000000000000..93936d16e139 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/jcore,spi.txt @@ -0,0 +1,34 @@ +J-Core SPI master + +Required properties: + +- compatible: Must be "jcore,spi2". + +- reg: Memory region for registers. + +- #address-cells: Must be 1. + +- #size-cells: Must be 0. + +Optional properties: + +- clocks: If a phandle named "ref_clk" is present, SPI clock speed + programming is relative to the frequency of the indicated clock. + Necessary only if the input clock rate is something other than a + fixed 50 MHz. + +- clock-names: Clock names, one for each phandle in clocks. + +See spi-bus.txt for additional properties not specific to this device. + +Example: + +spi@40 { + compatible = "jcore,spi2"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x40 0x8>; + spi-max-frequency = <25000000>; + clocks = <&bus_clk>; + clock-names = "ref_clk"; +} diff --git a/Documentation/devicetree/bindings/spi/spi-meson.txt b/Documentation/devicetree/bindings/spi/spi-meson.txt index bb52a86f3365..dc6d0313324a 100644 --- a/Documentation/devicetree/bindings/spi/spi-meson.txt +++ b/Documentation/devicetree/bindings/spi/spi-meson.txt @@ -7,7 +7,7 @@ NOR memories, without DMA support and a 64-byte unified transmit / receive buffer. Required properties: - - compatible: should be "amlogic,meson6-spifc" + - compatible: should be "amlogic,meson6-spifc" or "amlogic,meson-gxbb-spifc" - reg: physical base address and length of the controller registers - clocks: phandle of the input clock for the baud rate generator - #address-cells: should be 1 diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index 41b817f7b670..88b6ea1ad290 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -62,7 +62,7 @@ For more examples of cooling devices, refer to the example sections below. Required properties: - #cooling-cells: Used to provide cooling device specific information Type: unsigned while referring to it. Must be at least 2, in order - Size: one cell to specify minimum and maximum cooling state used + Size: one cell to specify minimum and maximum cooling state used in the reference. The first cell is the minimum cooling state requested and the second cell is the maximum cooling state requested in the reference. @@ -119,7 +119,7 @@ Required properties: Optional property: - contribution: The cooling contribution to the thermal zone of the Type: unsigned referred cooling device at the referred trip point. - Size: one cell The contribution is a ratio of the sum + Size: one cell The contribution is a ratio of the sum of all cooling contributions within a thermal zone. Note: Using the THERMAL_NO_LIMIT (-1UL) constant in the cooling-device phandle @@ -145,7 +145,7 @@ Required properties: Size: one cell - thermal-sensors: A list of thermal sensor phandles and sensor specifier - Type: list of used while monitoring the thermal zone. + Type: list of used while monitoring the thermal zone. phandles + sensor specifier @@ -473,7 +473,7 @@ thermal-zones { <&adc>; /* pcb north */ /* hotspot = 100 * bandgap - 120 * adc + 484 */ - coefficients = <100 -120 484>; + coefficients = <100 -120 484>; trips { ... @@ -502,7 +502,7 @@ from the ADC sensor. The binding would be then: thermal-sensors = <&adc>; /* hotspot = 1 * adc + 6000 */ - coefficients = <1 6000>; + coefficients = <1 6000>; (d) - Board thermal |
