diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
70 files changed, 1507 insertions, 186 deletions
diff --git a/Documentation/devicetree/bindings/arm/l2cc.txt b/Documentation/devicetree/bindings/arm/l2cc.txt index 2251dccb141e..06c88a4d28ac 100644 --- a/Documentation/devicetree/bindings/arm/l2cc.txt +++ b/Documentation/devicetree/bindings/arm/l2cc.txt @@ -67,6 +67,12 @@ Optional properties: disable if zero. - arm,prefetch-offset : Override prefetch offset value. Valid values are 0-7, 15, 23, and 31. +- arm,shared-override : The default behavior of the pl310 cache controller with + respect to the shareable attribute is to transform "normal memory + non-cacheable transactions" into "cacheable no allocate" (for reads) or + "write through no write allocate" (for writes). + On systems where this may cause DMA buffer corruption, this property must be + specified to indicate that such transforms are precluded. - prefetch-data : Data prefetch. Value: <0> (forcibly disable), <1> (forcibly enable), property absent (retain settings set by firmware) - prefetch-instr : Instruction prefetch. Value: <0> (forcibly disable), diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt index 3b5f5d1088c6..435251fa9ce0 100644 --- a/Documentation/devicetree/bindings/arm/pmu.txt +++ b/Documentation/devicetree/bindings/arm/pmu.txt @@ -26,13 +26,19 @@ Required properties: Optional properties: -- interrupt-affinity : Valid only when using SPIs, specifies a list of phandles - to CPU nodes corresponding directly to the affinity of +- interrupt-affinity : When using SPIs, specifies a list of phandles to CPU + nodes corresponding directly to the affinity of the SPIs listed in the interrupts property. - This property should be present when there is more than + When using a PPI, specifies a list of phandles to CPU + nodes corresponding to the set of CPUs which have + a PMU of this type signalling the PPI listed in the + interrupts property. + + This property should be present when there is more than a single SPI. + - qcom,no-pc-write : Indicates that this PMU doesn't support the 0xc and 0xd events. diff --git a/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt new file mode 100644 index 000000000000..47cb1d14b690 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/adi,axi-dmac.txt @@ -0,0 +1,61 @@ +Analog Device AXI-DMAC DMA controller + +Required properties: + - compatible: Must be "adi,axi-dmac-1.00.a". + - reg: Specification for the controllers memory mapped register map. + - interrupts: Specification for the controllers interrupt. + - clocks: Phandle and specifier to the controllers AXI interface clock + - #dma-cells: Must be 1. + +Required sub-nodes: + - adi,channels: This sub-node must contain a sub-node for each DMA channel. For + the channel sub-nodes the following bindings apply. They must match the + configuration options of the peripheral as it was instantiated. + +Required properties for adi,channels sub-node: + - #size-cells: Must be 0 + - #address-cells: Must be 1 + +Required channel sub-node properties: + - reg: Which channel this node refers to. + - adi,length-width: Width of the DMA transfer length register. + - adi,source-bus-width, + adi,destination-bus-width: Width of the source or destination bus in bits. + - adi,source-bus-type, + adi,destination-bus-type: Type of the source or destination bus. Must be one + of the following: + 0 (AXI_DMAC_TYPE_AXI_MM): Memory mapped AXI interface + 1 (AXI_DMAC_TYPE_AXI_STREAM): Streaming AXI interface + 2 (AXI_DMAC_TYPE_AXI_FIFO): FIFO interface + +Optional channel properties: + - adi,cyclic: Must be set if the channel supports hardware cyclic DMA + transfers. + - adi,2d: Must be set if the channel supports hardware 2D DMA transfers. + +DMA clients connected to the AXI-DMAC DMA controller must use the format +described in the dma.txt file using a one-cell specifier. The value of the +specifier refers to the DMA channel index. + +Example: + +dma: dma@7c420000 { + compatible = "adi,axi-dmac-1.00.a"; + reg = <0x7c420000 0x10000>; + interrupts = <0 57 0>; + clocks = <&clkc 16>; + #dma-cells = <1>; + + adi,channels { + #size-cells = <0>; + #address-cells = <1>; + + dma-channel@0 { + reg = <0>; + adi,source-bus-width = <32>; + adi,source-bus-type = <ADI_AXI_DMAC_TYPE_MM_AXI>; + adi,destination-bus-width = <64>; + adi,destination-bus-type = <ADI_AXI_DMAC_TYPE_FIFO>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/dma/arm-pl08x.txt b/Documentation/devicetree/bindings/dma/arm-pl08x.txt new file mode 100644 index 000000000000..8a0097a029d3 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/arm-pl08x.txt @@ -0,0 +1,54 @@ +* ARM PrimeCells PL080 and PL081 and derivatives DMA controller + +Required properties: +- compatible: "arm,pl080", "arm,primecell"; + "arm,pl081", "arm,primecell"; +- reg: Address range of the PL08x registers +- interrupt: The PL08x interrupt number +- clocks: The clock running the IP core clock +- clock-names: Must contain "apb_pclk" +- lli-bus-interface-ahb1: if AHB master 1 is eligible for fetching LLIs +- lli-bus-interface-ahb2: if AHB master 2 is eligible for fetching LLIs +- mem-bus-interface-ahb1: if AHB master 1 is eligible for fetching memory contents +- mem-bus-interface-ahb2: if AHB master 2 is eligible for fetching memory contents +- #dma-cells: must be <2>. First cell should contain the DMA request, + second cell should contain either 1 or 2 depending on + which AHB master that is used. + +Optional properties: +- dma-channels: contains the total number of DMA channels supported by the DMAC +- dma-requests: contains the total number of DMA requests supported by the DMAC +- memcpy-burst-size: the size of the bursts for memcpy: 1, 4, 8, 16, 32 + 64, 128 or 256 bytes are legal values +- memcpy-bus-width: the bus width used for memcpy: 8, 16 or 32 are legal + values + +Clients +Required properties: +- dmas: List of DMA controller phandle, request channel and AHB master id +- dma-names: Names of the aforementioned requested channels + +Example: + +dmac0: dma-controller@10130000 { + compatible = "arm,pl080", "arm,primecell"; + reg = <0x10130000 0x1000>; + interrupt-parent = <&vica>; + interrupts = <15>; + clocks = <&hclkdma0>; + clock-names = "apb_pclk"; + lli-bus-interface-ahb1; + lli-bus-interface-ahb2; + mem-bus-interface-ahb2; + memcpy-burst-size = <256>; + memcpy-bus-width = <32>; + #dma-cells = <2>; +}; + +device@40008000 { + ... + dmas = <&dmac0 0 2 + &dmac0 1 2>; + dma-names = "tx", "rx"; + ... +}; diff --git a/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt b/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt new file mode 100644 index 000000000000..87740adb2995 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/lpc1850-dmamux.txt @@ -0,0 +1,54 @@ +NXP LPC18xx/43xx DMA MUX (DMA request router) + +Required properties: +- compatible: "nxp,lpc1850-dmamux" +- reg: Memory map for accessing module +- #dma-cells: Should be set to <3>. + * 1st cell contain the master dma request signal + * 2nd cell contain the mux value (0-3) for the peripheral + * 3rd cell contain either 1 or 2 depending on the AHB + master used. +- dma-requests: Number of DMA requests for the mux +- dma-masters: phandle pointing to the DMA controller + +The DMA controller node need to have the following poroperties: +- dma-requests: Number of DMA requests the controller can handle + +Example: + +dmac: dma@40002000 { + compatible = "nxp,lpc1850-gpdma", "arm,pl080", "arm,primecell"; + arm,primecell-periphid = <0x00041080>; + reg = <0x40002000 0x1000>; + interrupts = <2>; + clocks = <&ccu1 CLK_CPU_DMA>; + clock-names = "apb_pclk"; + #dma-cells = <2>; + dma-channels = <8>; + dma-requests = <16>; + lli-bus-interface-ahb1; + lli-bus-interface-ahb2; + mem-bus-interface-ahb1; + mem-bus-interface-ahb2; + memcpy-burst-size = <256>; + memcpy-bus-width = <32>; +}; + +dmamux: dma-mux { + compatible = "nxp,lpc1850-dmamux"; + #dma-cells = <3>; + dma-requests = <64>; + dma-masters = <&dmac>; +}; + +uart0: serial@40081000 { + compatible = "nxp,lpc1850-uart", "ns16550a"; + reg = <0x40081000 0x1000>; + reg-shift = <2>; + interrupts = <24>; + clocks = <&ccu2 CLK_APB0_UART0>, <&ccu1 CLK_CPU_UART0>; + clock-names = "uartclk", "reg"; + dmas = <&dmamux 1 1 2 + &dmamux 2 1 2>; + dma-names = "tx", "rx"; +}; diff --git a/Documentation/devicetree/bindings/dma/mv-xor.txt b/Documentation/devicetree/bindings/dma/mv-xor.txt index cc29c35266e2..276ef815ef32 100644 --- a/Documentation/devicetree/bindings/dma/mv-xor.txt +++ b/Documentation/devicetree/bindings/dma/mv-xor.txt @@ -12,10 +12,13 @@ XOR engine has. Those sub-nodes have the following required properties: - interrupts: interrupt of the XOR channel -And the following optional properties: +The sub-nodes used to contain one or several of the following +properties, but they are now deprecated: - dmacap,memcpy to indicate that the XOR channel is capable of memcpy operations - dmacap,memset to indicate that the XOR channel is capable of memset operations - dmacap,xor to indicate that the XOR channel is capable of xor operations +- dmacap,interrupt to indicate that the XOR channel is capable of + generating interrupts Example: @@ -28,13 +31,8 @@ xor@d0060900 { xor00 { interrupts = <51>; - dmacap,memcpy; - dmacap,xor; }; xor01 { interrupts = <52>; - dmacap,memcpy; - dmacap,xor; - dmacap,memset; }; }; diff --git a/Documentation/devicetree/bindings/dma/sun4i-dma.txt b/Documentation/devicetree/bindings/dma/sun4i-dma.txt new file mode 100644 index 000000000000..f1634a27a830 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/sun4i-dma.txt @@ -0,0 +1,46 @@ +Allwinner A10 DMA Controller + +This driver follows the generic DMA bindings defined in dma.txt. + +Required properties: + +- compatible: Must be "allwinner,sun4i-a10-dma" +- reg: Should contain the registers base address and length +- interrupts: Should contain a reference to the interrupt used by this device +- clocks: Should contain a reference to the parent AHB clock +- #dma-cells : Should be 2, first cell denoting normal or dedicated dma, + second cell holding the request line number. + +Example: + dma: dma-controller@01c02000 { + compatible = "allwinner,sun4i-a10-dma"; + reg = <0x01c02000 0x1000>; + interrupts = <27>; + clocks = <&ahb_gates 6>; + #dma-cells = <2>; + }; + +Clients: + +DMA clients connected to the Allwinner A10 DMA controller must use the +format described in the dma.txt file, using a three-cell specifier for +each channel: a phandle plus two integer cells. +The three cells in order are: + +1. A phandle pointing to the DMA controller. +2. Whether it is using normal (0) or dedicated (1) channels +3. The port ID as specified in the datasheet + +Example: + spi2: spi@01c17000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c17000 0x1000>; + interrupts = <0 12 4>; + clocks = <&ahb_gates 22>, <&spi2_clk>; + clock-names = "ahb", "mod"; + dmas = <&dma 1 29>, <&dma 1 28>; + dma-names = "rx", "tx"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/dma/zxdma.txt b/Documentation/devicetree/bindings/dma/zxdma.txt new file mode 100644 index 000000000000..3207ceb04d0b --- /dev/null +++ b/Documentation/devicetree/bindings/dma/zxdma.txt @@ -0,0 +1,38 @@ +* ZTE ZX296702 DMA controller + +Required properties: +- compatible: Should be "zte,zx296702-dma" +- reg: Should contain DMA registers location and length. +- interrupts: Should contain one interrupt shared by all channel +- #dma-cells: see dma.txt, should be 1, para number +- dma-channels: physical channels supported +- dma-requests: virtual channels supported, each virtual channel + have specific request line +- clocks: clock required + +Example: + +Controller: + dma: dma-controller@0x09c00000{ + compatible = "zte,zx296702-dma"; + reg = <0x09c00000 0x1000>; + clocks = <&topclk ZX296702_DMA_ACLK>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + dma-channels = <24>; + dma-requests = <24>; + }; + +Client: +Use specific request line passing from dmax +For example, spdif0 tx channel request line is 4 + spdif0: spdif0@0b004000 { + #sound-dai-cells = <0>; + compatible = "zte,zx296702-spdif"; + reg = <0x0b004000 0x1000>; + clocks = <&lsp0clk ZX296702_SPDIF0_DIV>; + clock-names = "tx"; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dma 4>; + dma-names = "tx"; + } diff --git a/Documentation/devicetree/bindings/drm/msm/dsi.txt b/Documentation/devicetree/bindings/drm/msm/dsi.txt index cd8fe6cf536c..d56923cd5590 100644 --- a/Documentation/devicetree/bindings/drm/msm/dsi.txt +++ b/Documentation/devicetree/bindings/drm/msm/dsi.txt @@ -30,20 +30,27 @@ Optional properties: - panel@0: Node of panel connected to this DSI controller. See files in Documentation/devicetree/bindings/panel/ for each supported panel. -- qcom,dual-panel-mode: Boolean value indicating if the DSI controller is +- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is driving a panel which needs 2 DSI links. -- qcom,master-panel: Boolean value indicating if the DSI controller is driving +- qcom,master-dsi: Boolean value indicating if the DSI controller is driving the master link of the 2-DSI panel. -- qcom,sync-dual-panel: Boolean value indicating if the DSI controller is +- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is driving a 2-DSI panel whose 2 links need receive command simultaneously. - interrupt-parent: phandle to the MDP block if the interrupt signal is routed through MDP block +- pinctrl-names: the pin control state names; should contain "default" +- pinctrl-0: the default pinctrl state (active) +- pinctrl-n: the "sleep" pinctrl state +- port: DSI controller output port. This contains one endpoint subnode, with its + remote-endpoint set to the phandle of the connected panel's endpoint. + See Documentation/devicetree/bindings/graph.txt for device graph info. DSI PHY: Required properties: - compatible: Could be the following * "qcom,dsi-phy-28nm-hpm" * "qcom,dsi-phy-28nm-lp" + * "qcom,dsi-phy-20nm" - reg: Physical base address and length of the registers of PLL, PHY and PHY regulator - reg-names: The names of register regions. The following regions are required: @@ -59,6 +66,10 @@ Required properties: * "iface_clk" - vddio-supply: phandle to vdd-io regulator device node +Optional properties: +- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY + regulator is wanted. + Example: mdss_dsi0: qcom,mdss_dsi@fd922800 { compatible = "qcom,mdss-dsi-ctrl"; @@ -90,9 +101,13 @@ Example: qcom,dsi-phy = <&mdss_dsi_phy0>; - qcom,dual-panel-mode; - qcom,master-panel; - qcom,sync-dual-panel; + qcom,dual-dsi-mode; + qcom,master-dsi; + qcom,sync-dual-dsi; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mdss_dsi_active>; + pinctrl-1 = <&mdss_dsi_suspend>; panel: panel@0 { compatible = "sharp,lq101r1sx01"; @@ -101,6 +116,18 @@ Example: power-supply = <...>; backlight = <...>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; }; }; @@ -117,4 +144,6 @@ Example: clock-names = "iface_clk"; clocks = <&mmcc MDSS_AHB_CLK>; vddio-supply = <&pma8084_l12>; + + qcom,dsi-phy-regulator-ldo-mode; }; diff --git a/Documentation/devicetree/bindings/drm/msm/hdmi.txt b/Documentation/devicetree/bindings/drm/msm/hdmi.txt index c43aa53debed..e926239e1101 100644 --- a/Documentation/devicetree/bindings/drm/msm/hdmi.txt +++ b/Documentation/devicetree/bindings/drm/msm/hdmi.txt @@ -2,8 +2,9 @@ Qualcomm adreno/snapdragon hdmi output Required properties: - compatible: one of the following + * "qcom,hdmi-tx-8994" * "qcom,hdmi-tx-8084" - * "qcom,hdmi-tx-8074" + * "qcom,hdmi-tx-8974" * "qcom,hdmi-tx-8660" * "qcom,hdmi-tx-8960" - reg: Physical base address and length of the controller's registers diff --git a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt index 435f1bcca341..b405b4410bfb 100644 --- a/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt +++ b/Documentation/devicetree/bindings/gpio/brcm,brcmstb-gpio.txt @@ -33,6 +33,13 @@ Optional properties: - interrupt-parent: phandle of the parent interrupt controller +- interrupts-extended: + Alternate form of specifying interrupts and parents that allows for + multiple parents. This takes precedence over 'interrupts' and + 'interrupt-parent'. Wakeup-capable GPIO controllers often route their + wakeup interrupt lines through a different interrupt controller than the + primary interrupt line, making this property necessary. + - #interrupt-cells: Should be <2>. The first cell is the GPIO number, the second should specify flags. The following subset of flags is supported: @@ -47,19 +54,33 @@ Optional properties: - interrupt-controller: Marks the device node as an interrupt controller -- interrupt-names: - The name of the IRQ resource used by this controller +- wakeup-source: + GPIOs for this controller can be used as a wakeup source Example: upg_gio: gpio@f040a700 { - #gpio-cells = <0x2>; - #interrupt-cells = <0x2>; + #gpio-cells = <2>; + #interrupt-cells = <2>; compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; gpio-controller; interrupt-controller; reg = <0xf040a700 0x80>; - interrupt-parent = <0xf>; + interrupt-parent = <&irq0_intc>; + interrupts = <0x6>; + brcm,gpio-bank-widths = <32 32 32 24>; + }; + + upg_gio_aon: gpio@f04172c0 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + compatible = "brcm,bcm7445-gpio", "brcm,brcmstb-gpio"; + gpio-controller; + interrupt-controller; + reg = <0xf04172c0 0x40>; + interrupt-parent = <&irq0_aon_intc>; interrupts = <0x6>; - interrupt-names = "upg_gio"; - brcm,gpio-bank-widths = <0x20 0x20 0x20 0x18>; + interrupts-extended = <&irq0_aon_intc 0x6>, + <&aon_pm_l2_intc 0x5>; + wakeup-source; + brcm,gpio-bank-widths = <18 4>; }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt index abf4db736c6e..170194af3027 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-etraxfs.txt @@ -2,8 +2,9 @@ Axis ETRAX FS General I/O controller bindings Required properties: -- compatible: +- compatible: one of: - "axis,etraxfs-gio" + - "axis,artpec3-gio" - reg: Physical base address and length of the controller's registers. - #gpio-cells: Should be 3 - The first cell is the gpio offset number. diff --git a/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt new file mode 100644 index 000000000000..805ddcd79a57 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-mpc8xxx.txt @@ -0,0 +1,22 @@ +* Freescale MPC512x/MPC8xxx GPIO controller + +Required properties: +- compatible : Should be "fsl,<soc>-gpio" + The following <soc>s are known to be supported: + mpc5121, mpc5125, mpc8349, mpc8572, mpc8610, pq3, qoriq +- reg : Address and length of the register set for the device +- interrupts : Should be the port interrupt shared by all 32 pins. +- #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify the gpio polarity: + 0 = active high + 1 = active low + +Example: + +gpio0: gpio@1100 { + compatible = "fsl,mpc5125-gpio"; + #gpio-cells = <2>; + reg = <0x1100 0x080>; + interrupts = <78 0x8>; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt index 38fb86f28ba2..f60e2f477e93 100644 --- a/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt +++ b/Documentation/devicetree/bindings/gpio/renesas,gpio-rcar.txt @@ -9,6 +9,7 @@ Required Properties: - "renesas,gpio-r8a7791": for R8A7791 (R-Car M2-W) compatible GPIO controller. - "renesas,gpio-r8a7793": for R8A7793 (R-Car M2-N) compatible GPIO controller. - "renesas,gpio-r8a7794": for R8A7794 (R-Car E2) compatible GPIO controller. + - "renesas,gpio-r8a7795": for R8A7795 (R-Car H3) compatible GPIO controller. - "renesas,gpio-rcar": for generic R-Car GPIO controller. - reg: Base address and length of each memory resource used by the GPIO diff --git a/Documentation/devicetree/bindings/gpio/zx296702-gpio.txt b/Documentation/devicetree/bindings/gpio/zx296702-gpio.txt new file mode 100644 index 000000000000..0dab156fcf41 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/zx296702-gpio.txt @@ -0,0 +1,24 @@ +ZTE ZX296702 GPIO controller + +Required properties: +- compatible : "zte,zx296702-gpio" +- #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters: + - bit 0 specifies polarity (0 for normal, 1 for inverted) +- gpio-controller : Marks the device node as a GPIO controller. +- interrupts : Interrupt mapping for GPIO IRQ. +- gpio-ranges : Interaction with the PINCTRL subsystem. + +gpio1: gpio@b008040 { + compatible = "zte,zx296702-gpio"; + reg = <0xb008040 0x40>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = < &pmx0 0 54 2 &pmx0 2 59 14>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&intc>; + interrupt-controller; + #interrupt-cells = <2>; + clock-names = "gpio_pclk"; + clocks = <&lsp0clk ZX296702_GPIO_CLK>; +}; diff --git a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt index 009f4bfa1590..e685610d38e2 100644 --- a/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt +++ b/Documentation/devicetree/bindings/gpu/nvidia,tegra20-host1x.txt @@ -197,9 +197,11 @@ of the following host1x client modules: - sor: serial output resource Required properties: - - compatible: For Tegra124, must contain "nvidia,tegra124-sor". Otherwise, - must contain '"nvidia,<chip>-sor", "nvidia,tegra124-sor"', where <chip> - is tegra132. + - compatible: Should be: + - "nvidia,tegra124-sor": for Tegra124 and Tegra132 + - "nvidia,tegra132-sor": for Tegra132 + - "nvidia,tegra210-sor": for Tegra210 + - "nvidia,tegra210-sor1": for Tegra210 - reg: Physical base address and length of the controller's registers. - interrupts: The interrupt outputs from the controller. - clocks: Must contain an entry for each entry in clock-names. diff --git a/Documentation/devicetree/bindings/gpu/st,stih4xx.txt b/Documentation/devicetree/bindings/gpu/st,stih4xx.txt index 6b1d75f1a529..a36dfce0032e 100644 --- a/Documentation/devicetree/bindings/gpu/st,stih4xx.txt +++ b/Documentation/devicetree/bindings/gpu/st,stih4xx.txt @@ -52,10 +52,9 @@ STMicroelectronics stih4xx platforms See ../reset/reset.txt for details. - reset-names: names of the resets listed in resets property in the same order. - - ranges: to allow probing of subdevices - sti-hdmi: hdmi output block - must be a child of sti-tvout + must be a child of sti-display-subsystem Required properties: - compatible: "st,stih<chip>-hdmi"; - reg: Physical base address of the IP registers and length of memory mapped region. @@ -72,7 +71,7 @@ STMicroelectronics stih4xx platforms sti-hda: Required properties: - must be a child of sti-tvout + must be a child of sti-display-subsystem - compatible: "st,stih<chip>-hda" - reg: Physical base address of the IP registers and length of memory mapped region. - reg-names: names of the mapped memory regions listed in regs property in @@ -85,7 +84,7 @@ sti-hda: sti-dvo: Required properties: - must be a child of sti-tvout + must be a child of sti-display-subsystem - compatible: "st,stih<chip>-dvo" - reg: Physical base address of the IP registers and length of memory mapped region. - reg-names: names of the mapped memory regions listed in regs property in @@ -195,38 +194,37 @@ Example: reg-names = "tvout-reg", "hda-reg", "syscfg"; reset-names = "tvout"; resets = <&softreset STIH416_HDTVOUT_SOFTRESET>; - ranges; - - sti-hdmi@fe85c000 { - compatible = "st,stih416-hdmi"; - reg = <0xfe85c000 0x1000>, <0xfe830000 0x10000>; - reg-names = "hdmi-reg", "syscfg"; - interrupts = <GIC_SPI 173 IRQ_TYPE_NONE>; - interrupt-names = "irq"; - clock-names = "pix", "tmds", "phy", "audio"; - clocks = <&clockgen_c_vcc CLK_S_PIX_HDMI>, <&clockgen_c_vcc CLK_S_TMDS_HDMI>, <&clockgen_c_vcc CLK_S_HDMI_REJECT_PLL>, <&clockgen_b1 CLK_S_PCM_0>; - }; - - sti-hda@fe85a000 { - compatible = "st,stih416-hda"; - reg = <0xfe85a000 0x400>, <0xfe83085c 0x4>; - reg-names = "hda-reg", "video-dacs-ctrl"; - clock-names = "pix", "hddac"; - clocks = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>; - }; - - sti-dvo@8d00400 { - compatible = "st,stih407-dvo"; - reg = <0x8d00400 0x200>; - reg-names = "dvo-reg"; - clock-names = "dvo_pix", "dvo", - "main_parent", "aux_parent"; - clocks = <&clk_s_d2_flexgen CLK_PIX_DVO>, <&clk_s_d2_flexgen CLK_DVO>, - <&clk_s_d2_quadfs 0>, <&clk_s_d2_quadfs 1>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_dvo>; - sti,panel = <&panel_dvo>; - }; + }; + + sti-hdmi@fe85c000 { + compatible = "st,stih416-hdmi"; + reg = <0xfe85c000 0x1000>, <0xfe830000 0x10000>; + reg-names = "hdmi-reg", "syscfg"; + interrupts = <GIC_SPI 173 IRQ_TYPE_NONE>; + interrupt-names = "irq"; + clock-names = "pix", "tmds", "phy", "audio"; + clocks = <&clockgen_c_vcc CLK_S_PIX_HDMI>, <&clockgen_c_vcc CLK_S_TMDS_HDMI>, <&clockgen_c_vcc CLK_S_HDMI_REJECT_PLL>, <&clockgen_b1 CLK_S_PCM_0>; + }; + + sti-hda@fe85a000 { + compatible = "st,stih416-hda"; + reg = <0xfe85a000 0x400>, <0xfe83085c 0x4>; + reg-names = "hda-reg", "video-dacs-ctrl"; + clock-names = "pix", "hddac"; + clocks = <&clockgen_c_vcc CLK_S_PIX_HD>, <&clockgen_c_vcc CLK_S_HDDAC>; + }; + + sti-dvo@8d00400 { + compatible = "st,stih407-dvo"; + reg = <0x8d00400 0x200>; + reg-names = "dvo-reg"; + clock-names = "dvo_pix", "dvo", + "main_parent", "aux_parent"; + clocks = <&clk_s_d2_flexgen CLK_PIX_DVO>, <&clk_s_d2_flexgen CLK_DVO>, + <&clk_s_d2_quadfs 0>, <&clk_s_d2_quadfs 1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dvo>; + sti,panel = <&panel_dvo>; }; sti-hqvdp@9c000000 { @@ -237,7 +235,7 @@ Example: reset-names = "hqvdp"; resets = <&softreset STIH407_HDQVDP_SOFTRESET>; st,vtg = <&vtg_main>; - }; + }; }; ... }; diff --git a/Documentation/devicetree/bindings/input/ads7846.txt b/Documentation/devicetree/bindings/input/ads7846.txt index 5f7619c22743..df8b1279491d 100644 --- a/Documentation/devicetree/bindings/input/ads7846.txt +++ b/Documentation/devicetree/bindings/input/ads7846.txt @@ -64,7 +64,7 @@ Optional properties: pendown-gpio (u32). pendown-gpio GPIO handle describing the pin the !PENIRQ line is connected to. - linux,wakeup use any event on touchscreen as wakeup event. + wakeup-source use any event on touchscreen as wakeup event. Example for a TSC2046 chip connected to an McSPI controller of an OMAP SoC:: diff --git a/Documentation/devicetree/bindings/input/cap11xx.txt b/Documentation/devicetree/bindings/input/cap11xx.txt index 7d0a3009771b..8c67a0b5058d 100644 --- a/Documentation/devicetree/bindings/input/cap11xx.txt +++ b/Documentation/devicetree/bindings/input/cap11xx.txt @@ -55,5 +55,24 @@ i2c_controller { <105>, /* KEY_LEFT */ <109>, /* KEY_PAGEDOWN */ <104>; /* KEY_PAGEUP */ + + #address-cells = <1>; + #size-cells = <0>; + + usr@0 { + label = "cap11xx:green:usr0"; + reg = <0>; + }; + + usr@1 { + label = "cap11xx:green:usr1"; + reg = <1>; + }; + + alive@2 { + label = "cap11xx:green:alive"; + reg = <2>; + linux,default_trigger = "heartbeat"; + }; }; } diff --git a/Documentation/devicetree/bindings/input/cypress,cyapa.txt b/Documentation/devicetree/bindings/input/cypress,cyapa.txt new file mode 100644 index 000000000000..635a3b036630 --- /dev/null +++ b/Documentation/devicetree/bindings/input/cypress,cyapa.txt @@ -0,0 +1,44 @@ +Cypress I2C Touchpad + +Required properties: +- compatible: must be "cypress,cyapa". +- reg: I2C address of the chip. +- interrupt-parent: a phandle for the interrupt controller (see interrupt + binding[0]). +- interrupts: interrupt to which the chip is connected (see interrupt + binding[0]). + +Optional properties: +- wakeup-source: touchpad can be used as a wakeup source. +- pinctrl-names: should be "default" (see pinctrl binding [1]). +- pinctrl-0: a phandle pointing to the pin settings for the device (see + pinctrl binding [1]). +- vcc-supply: a phandle for the regulator supplying 3.3V power. + +[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt +[1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +Example: + &i2c0 { + /* ... */ + + /* Cypress Gen3 touchpad */ + touchpad@67 { + compatible = "cypress,cyapa"; + reg = <0x24>; + interrupt-parent = <&gpio>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO 2 */ + wakeup-source; + }; + + /* Cypress Gen5 and later touchpad */ + touchpad@24 { + compatible = "cypress,cyapa"; + reg = <0x24>; + interrupt-parent = <&gpio>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO 2 */ + wakeup-source; + }; + + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/input/elants_i2c.txt b/Documentation/devicetree/bindings/input/elants_i2c.txt index a765232e6446..8a71038f3489 100644 --- a/Documentation/devicetree/bindings/input/elants_i2c.txt +++ b/Documentation/devicetree/bindings/input/elants_i2c.txt @@ -13,6 +13,9 @@ Optional properties: - pinctrl-names: should be "default" (see pinctrl binding [1]). - pinctrl-0: a phandle pointing to the pin settings for the device (see pinctrl binding [1]). +- reset-gpios: reset gpio the chip is connected to. +- vcc33-supply: a phandle for the regulator supplying 3.3V power. +- vccio-supply: a phandle for the regulator supplying IO power. [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt [1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt diff --git a/Documentation/devicetree/bindings/input/gpio-keys-polled.txt b/Documentation/devicetree/bindings/input/gpio-keys-polled.txt index 313abefa37cc..5b91f5a3bd5c 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys-polled.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys-polled.txt @@ -20,7 +20,7 @@ Optional subnode-properties: If not specified defaults to <1> == EV_KEY. - debounce-interval: Debouncing interval time in milliseconds. If not specified defaults to 5. - - gpio-key,wakeup: Boolean, button can wake-up the system. + - wakeup-source: Boolean, button can wake-up the system. Example nodes: diff --git a/Documentation/devicetree/bindings/input/gpio-keys.txt b/Documentation/devicetree/bindings/input/gpio-keys.txt index 44b705767aca..072bf7573c37 100644 --- a/Documentation/devicetree/bindings/input/gpio-keys.txt +++ b/Documentation/devicetree/bindings/input/gpio-keys.txt @@ -23,7 +23,7 @@ Optional subnode-properties: If not specified defaults to <1> == EV_KEY. - debounce-interval: Debouncing interval time in milliseconds. If not specified defaults to 5. - - gpio-key,wakeup: Boolean, button can wake-up the system. + - wakeup-source: Boolean, button can wake-up the system. - linux,can-disable: Boolean, indicates that button is connected to dedicated (not shared) interrupt which can be disabled to suppress events from the button. diff --git a/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt index ead641c65e0a..4d86059c370c 100644 --- a/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt +++ b/Documentation/devicetree/bindings/input/gpio-matrix-keypad.txt @@ -19,7 +19,7 @@ Required Properties: Optional Properties: - linux,no-autorepeat: do no enable autorepeat feature. -- linux,wakeup: use any event on keypad as wakeup event. +- wakeup-source: use any event on keypad as wakeup event. - debounce-delay-ms: debounce interval in milliseconds - col-scan-delay-us: delay, measured in microseconds, that is needed before we can scan keypad after activating column gpio diff --git a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt index 7d8cb92831d7..ee6215681182 100644 --- a/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt +++ b/Documentation/devicetree/bindings/input/qcom,pm8xxx-keypad.txt @@ -33,7 +33,7 @@ PROPERTIES Value type: <bool> Definition: don't enable autorepeat feature. -- linux,keypad-wakeup: +- wakeup-source: Usage: optional Value type: <bool> Definition: use any event on keypad as wakeup event. diff --git a/Documentation/devicetree/bindings/input/samsung-keypad.txt b/Documentation/devicetree/bindings/input/samsung-keypad.txt index 942d071baaa5..863e77f619dc 100644 --- a/Documentation/devicetree/bindings/input/samsung-keypad.txt +++ b/Documentation/devicetree/bindings/input/samsung-keypad.txt @@ -36,9 +36,11 @@ Required Board Specific Properties: - pinctrl-0: Should specify pin control groups used for this controller. - pinctrl-names: Should contain only one value - "default". +Optional Properties: +- wakeup-source: use any event on keypad as wakeup event. + Optional Properties specific to linux: - linux,keypad-no-autorepeat: do no enable autorepeat feature. -- linux,keypad-wakeup: use any event on keypad as wakeup event. Example: diff --git a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt index 6e551090f465..8eb240a287c8 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt @@ -8,6 +8,9 @@ Required properties: - touchscreen-size-x: horizontal resolution of touchscreen (in pixels) - touchscreen-size-y: vertical resolution of touchscreen (in pixels) +Optional properties: +- reset-gpio: GPIO connected to the RESET line of the chip + Example: i2c@00000000 { diff --git a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt index 80c37df940a7..e3c27c4fd9c8 100644 --- a/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt +++ b/Documentation/devicetree/bindings/input/touchscreen/zforce_ts.txt @@ -4,12 +4,12 @@ Required properties: - compatible: must be "neonode,zforce" - reg: I2C address of the chip - interrupts: interrupt to which the chip is connected -- gpios: gpios the chip is connected to - first one is the interrupt gpio and second one the reset gpio +- reset-gpios: reset gpio the chip is connected to - x-size: horizontal resolution of touchscreen - y-size: vertical resolution of touchscreen Optional properties: +- irq-gpios : interrupt gpio the chip is connected to - vdd-supply: Regulator controlling the controller supply Example: @@ -23,8 +23,8 @@ Example: interrupts = <2 0>; vdd-supply = <®_zforce_vdd>; - gpios = <&gpio5 6 0>, /* INT */ - <&gpio5 9 0>; /* RST */ + reset-gpios = <&gpio5 9 0>; /* RST */ + irq-gpios = <&gpio5 6 0>; /* IRQ, optional */ x-size = <800>; y-size = <600>; diff --git a/Documentation/devicetree/bindings/leds/leds-powernv.txt b/Documentation/devicetree/bindings/leds/leds-powernv.txt new file mode 100644 index 000000000000..66655690f749 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-powernv.txt @@ -0,0 +1,26 @@ +Device Tree binding for LEDs on IBM Power Systems +------------------------------------------------- + +Required properties: +- compatible : Should be "ibm,opal-v3-led". +- led-mode : Should be "lightpath" or "guidinglight". + +Each location code of FRU/Enclosure must be expressed in the +form of a sub-node. + +Required properties for the sub nodes: +- led-types : Supported LED types (attention/identify/fault) provided + in the form of string array. + +Example: + +leds { + compatible = "ibm,opal-v3-led"; + led-mode = "lightpath"; + + U78C9.001.RST0027-P1-C1 { + led-types = "identify", "fault"; + }; + ... + ... +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt b/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt index d5e370450ac0..89427b018ba7 100644 --- a/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt +++ b/Documentation/devicetree/bindings/memory-controllers/fsl/ifc.txt @@ -18,6 +18,8 @@ Properties: interrupt (NAND_EVTER_STAT). If there is only one, that interrupt reports both types of event. +- little-endian : If this property is absent, the big-endian mode will + be in use as default for registers. - ranges : Each range corresponds to a single chipselect, and covers the entire access window as configured. @@ -34,6 +36,7 @@ Example: #size-cells = <1>; reg = <0x0 0xffe1e000 0 0x2000>; interrupts = <16 2 19 2>; + little-endian; /* NOR, NAND Flashes and CPLD on board */ ranges = <0x0 0x0 0x0 0xee000000 0x02000000 diff --git a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt index f64de95a8e8b..ad5d90482a0e 100644 --- a/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt +++ b/Documentation/devicetree/bindings/mfd/atmel-hlcdc.txt @@ -2,7 +2,11 @@ Device-Tree bindings for Atmel's HLCDC (High LCD Controller) MFD driver Required properties: - compatible: value should be one of the following: + "atmel,at91sam9n12-hlcdc" + "atmel,at91sam9x5-hlcdc" + "atmel,sama5d2-hlcdc" "atmel,sama5d3-hlcdc" + "atmel,sama5d4-hlcdc" - reg: base address and size of the HLCDC device registers. - clock-names: the name of the 3 clocks requested by the HLCDC device. Should contain "periph_clk", "sys_clk" and "slow_clk". diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index 753f14f46e85..41811223e5be 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -1,12 +1,14 @@ AXP family PMIC device tree bindings The axp20x family current members : +axp152 (X-Powers) axp202 (X-Powers) axp209 (X-Powers) axp221 (X-Powers) Required properties: -- compatible: "x-powers,axp202", "x-powers,axp209", "x-powers,axp221" +- compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209", + "x-powers,axp221" - reg: The I2C slave address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin diff --git a/Documentation/devicetree/bindings/mfd/da9062.txt b/Documentation/devicetree/bindings/mfd/da9062.txt new file mode 100644 index 000000000000..38802b54d48a --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/da9062.txt @@ -0,0 +1,88 @@ +* Dialog DA9062 Power Management Integrated Circuit (PMIC) + +DA9062 consists of a large and varied group of sub-devices: + +Device Supply Names Description +------ ------------ ----------- +da9062-regulator : : LDOs & BUCKs +da9062-rtc : : Real-Time Clock +da9062-watchdog : : Watchdog Timer + +====== + +Required properties: + +- compatible : Should be "dlg,da9062". +- reg : Specifies the I2C slave address (this defaults to 0x58 but it can be + modified to match the chip's OTP settings). +- interrupt-parent : Specifies the reference to the interrupt controller for + the DA9062. +- interrupts : IRQ line information. +- interrupt-controller + +See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for +further information on IRQ bindings. + +Sub-nodes: + +- regulators : This node defines the settings for the LDOs and BUCKs. The + DA9062 regulators are bound using their names listed below: + + buck1 : BUCK_1 + buck2 : BUCK_2 + buck3 : BUCK_3 + buck4 : BUCK_4 + ldo1 : LDO_1 + ldo2 : LDO_2 + ldo3 : LDO_3 + ldo4 : LDO_4 + + The component follows the standard regulator framework and the bindings + details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + + +- rtc : This node defines settings required for the Real-Time Clock associated + with the DA9062. There are currently no entries in this binding, however + compatible = "dlg,da9062-rtc" should be added if a node is created. + +- watchdog: This node defines the settings for the watchdog driver associated + with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added + if a node is created. + + +Example: + + pmic0: da9062@58 { + compatible = "dlg,da9062"; + reg = <0x58>; + interrupt-parent = <&gpio6>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + + rtc { + compatible = "dlg,da9062-rtc"; + }; + + watchdog { + compatible = "dlg,da9062-watchdog"; + }; + + regulators { + DA9062_BUCK1: buck1 { + regulator-name = "BUCK1"; + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <500000>; + regulator-max-microamp = <2000000>; + regulator-boot-on; + }; + DA9062_LDO1: ldo1 { + regulator-name = "LDO_1"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <3600000>; + regulator-boot-on; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt index 163bd81a4607..741e76688cf2 100644 --- a/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -7,8 +7,9 @@ different i2c slave address,presently for which we are statically creating i2c client while probing.This document describes the binding for mfd device and PMIC submodule. -Binding for the built-in 32k clock generator block is defined separately -in bindings/clk/maxim,max77686.txt file. +Bindings for the built-in 32k clock generator block and +regulators are defined in ../clk/maxim,max77686.txt and +../regulator/max77686.txt respectively. Required properties: - compatible : Must be "maxim,max77686"; @@ -16,67 +17,11 @@ Required properties: - interrupts : This i2c device has an IRQ line connected to the main SoC. - interrupt-parent : The parent interrupt controller. -Optional node: -- voltage-regulators : The regulators of max77686 have to be instantiated - under subnode named "voltage-regulators" using the following format. - - regulator_name { - regulator-compatible = LDOn/BUCKn - standard regulator constraints.... - }; - refer Documentation/devicetree/bindings/regulator/regulator.txt - - The regulator-compatible property of regulator should initialized with string -to get matched with their hardware counterparts as follow: - - -LDOn : for LDOs, where n can lie in range 1 to 26. - example: LDO1, LDO2, LDO26. - -BUCKn : for BUCKs, where n can lie in range 1 to 9. - example: BUCK1, BUCK5, BUCK9. - - Regulators which can be turned off during system suspend: - -LDOn : 2, 6-8, 10-12, 14-16, - -BUCKn : 1-4. - Use standard regulator bindings for it ('regulator-off-in-suspend'). - - LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable - control. To turn this feature on this property must be added to the regulator - sub-node: - - maxim,ena-gpios : one GPIO specifier enable control (the gpio - flags are actually ignored and always - ACTIVE_HIGH is used) - Example: - max77686@09 { + max77686: pmic@09 { compatible = "maxim,max77686"; interrupt-parent = <&wakeup_eint>; interrupts = <26 0>; reg = <0x09>; - - voltage-regulators { - ldo11_reg { - regulator-compatible = "LDO11"; - regulator-name = "vdd_ldo11"; - regulator-min-microvolt = <1900000>; - regulator-max-microvolt = <1900000>; - regulator-always-on; - }; - - buck1_reg { - regulator-compatible = "BUCK1"; - regulator-name = "vdd_mif"; - regulator-min-microvolt = <950000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - regulator-boot-on; - }; - - buck9_reg { - regulator-compatible = "BUCK9"; - regulator-name = "CAM_ISP_CORE_1.2V"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1200000>; - maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>; - }; - } + }; diff --git a/Documentation/devicetree/bindings/mfd/max77802.txt b/Documentation/devicetree/bindings/mfd/max77802.txt new file mode 100644 index 000000000000..51fc1a60caa5 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/max77802.txt @@ -0,0 +1,26 @@ +Maxim MAX77802 multi-function device + +The Maxim MAX77802 is a Power Management IC (PMIC) that contains 10 high +efficiency Buck regulators, 32 Low-DropOut (LDO) regulators used to power +up application processors and peripherals, a 2-channel 32kHz clock outputs, +a Real-Time-Clock (RTC) and a I2C interface to program the individual +regulators, clocks outputs and the RTC. + +Bindings for the built-in 32k clock generator block and +regulators are defined in ../clk/maxim,max77802.txt and +../regulator/max77802.txt respectively. + +Required properties: +- compatible : Must be "maxim,max77802" +- reg : Specifies the I2C slave address of PMIC block. +- interrupts : I2C device IRQ line connected to the main SoC. +- interrupt-parent : The parent interrupt controller. + +Example: + + max77802: pmic@09 { + compatible = "maxim,max77802"; + interrupt-parent = <&intc>; + interrupts = <26 IRQ_TYPE_NONE>; + reg = <0x09>; + }; diff --git a/Documentation/devicetree/bindings/mfd/tc3589x.txt b/Documentation/devicetree/bindings/mfd/tc3589x.txt index 6fcedba46ae9..37bf7f1aa70a 100644 --- a/Documentation/devicetree/bindings/mfd/tc3589x.txt +++ b/Documentation/devicetree/bindings/mfd/tc3589x.txt @@ -55,7 +55,7 @@ Optional nodes: - linux,keymap: the definition can be found in bindings/input/matrix-keymap.txt - linux,no-autorepeat: do no enable autorepeat feature. - - linux,wakeup: use any event on keypad as wakeup event. + - wakeup-source: use any event on keypad as wakeup event. Example: @@ -84,7 +84,6 @@ tc35893@44 { keypad,num-columns = <8>; keypad,num-rows = <8>; linux,no-autorepeat; - linux,wakeup; linux,keymap = <0x0301006b 0x04010066 0x06040072 @@ -103,5 +102,6 @@ tc35893@44 { 0x01030039 0x07060069 0x050500d9>; + wakeup-source; }; }; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt index f0b4cd72411d..04e6bef3ac3f 100644 --- a/Documentation/devicetree/bindings/net/dsa/dsa.txt +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -44,9 +44,10 @@ Note that a port labelled "dsa" will imply checking for the uplink phandle described below. Optionnal property: -- link : Should be a phandle to another switch's DSA port. +- link : Should be a list of phandles to another switch's DSA port. This property is only used when switches are being - chained/cascaded together. + chained/cascaded together. This port is used as outgoing port + towards the phandle port, which can be more than one hop away. - phy-handle : Phandle to a PHY on an external MDIO bus, not the switch internal one. See @@ -58,6 +59,10 @@ Optionnal property: Documentation/devicetree/bindings/net/ethernet.txt for details. +- mii-bus : Should be a phandle to a valid MDIO bus device node. + This mii-bus will be used in preference to the + global dsa,mii-bus defined above, for this switch. + Optional subnodes: - fixed-link : Fixed-link subnode describing a link to a non-MDIO managed entity. See @@ -96,10 +101,11 @@ Example: label = "cpu"; }; - switch0uplink: port@6 { + switch0port6: port@6 { reg = <6>; label = "dsa"; - link = <&switch1uplink>; + link = <&switch1port0 + &switch2port0>; }; }; @@ -107,11 +113,31 @@ Example: #address-cells = <1>; #size-cells = <0>; reg = <17 1>; /* MDIO address 17, switch 1 in tree */ + mii-bus = <&mii_bus1>; + + switch1port0: port@0 { + reg = <0>; + label = "dsa"; + link = <&switch0port6>; + }; + switch1port1: port@1 { + reg = <1>; + label = "dsa"; + link = <&switch2port1>; + }; + }; + + switch@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <18 2>; /* MDIO address 18, switch 2 in tree */ + mii-bus = <&mii_bus1>; - switch1uplink: port@0 { + switch2port0: port@0 { reg = <0>; label = "dsa"; - link = <&switch0uplink>; + link = <&switch1port1 + &switch0port6>; }; }; }; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt index 41b3f3f864e8..5d88f37480b6 100644 --- a/Documentation/devicetree/bindings/net/ethernet.txt +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -25,7 +25,11 @@ The following properties are common to the Ethernet controllers: flow control thresholds. - tx-fifo-depth: the size of the controller's transmit fifo in bytes. This is used for components that can have configurable fifo sizes. +- managed: string, specifies the PHY management type. Supported values are: + "auto", "in-band-status". "auto" is the default, it usess MDIO for + management if fixed-link is not specified. Child nodes of the Ethernet controller are typically the individual PHY devices connected via the MDIO bus (sometimes the MDIO bus controller is separate). They are described in the phy.txt file in this same directory. +For non-MDIO PHY management see fixed-link.txt. diff --git a/Documentation/devicetree/bindings/net/fixed-link.txt b/Documentation/devicetree/bindings/net/fixed-link.txt index 82bf7e0f47b6..ec5d889fe3d8 100644 --- a/Documentation/devicetree/bindings/net/fixed-link.txt +++ b/Documentation/devicetree/bindings/net/fixed-link.txt @@ -17,6 +17,8 @@ properties: enabled. * 'asym-pause' (boolean, optional), to indicate that asym_pause should be enabled. +* 'link-gpios' ('gpio-list', optional), to indicate if a gpio can be read + to determine if the link is up. Old, deprecated 'fixed-link' binding: @@ -30,7 +32,7 @@ Old, deprecated 'fixed-link' binding: - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for asymmetric pause -Example: +Examples: ethernet@0 { ... @@ -40,3 +42,13 @@ ethernet@0 { }; ... }; + +ethernet@1 { + ... + fixed-link { + speed = <1000>; + pause; + link-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt index d0e6fa38f335..b30ab6b5cbfa 100644 --- a/Documentation/devicetree/bindings/net/keystone-netcp.txt +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -130,7 +130,11 @@ Required properties: Optional properties: - efuse-mac: If this is 1, then the MAC address for the interface is - obtained from the device efuse mac address register + obtained from the device efuse mac address register. + If this is 2, the two DWORDs occupied by the MAC address + are swapped. The netcp driver will swap the two DWORDs + back to the proper order when this property is set to 2 + when it obtains the mac address from efuse. - local-mac-address: the driver is designed to use the of_get_mac_address api only if efuse-mac is 0. When efuse-mac is 0, the MAC address is obtained from local-mac-address. If this diff --git a/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt new file mode 100644 index 000000000000..fb1e75facf1b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt @@ -0,0 +1,27 @@ +* Samsung S3FWRN5 NCI NFC Controller + +Required properties: +- compatible: Should be "samsung,s3fwrn5-i2c". +- reg: address on the bus +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- s3fwrn5,en-gpios: Output GPIO pin used for enabling/disabling the chip +- s3fwrn5,fw-gpios: Output GPIO pin used to enter firmware mode and + sleep/wakeup control + +Example: + +&hsi2c_4 { + status = "okay"; + s3fwrn5@27 { + compatible = "samsung,s3fwrn5-i2c"; + + reg = <0x27>; + + interrupt-parent = <&gpa1>; + interrupts = <3 0 0>; + + s3fwrn5,en-gpios = <&gpf1 4 0>; + s3fwrn5,fw-gpios = <&gpj0 2 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt index d707588ed734..d707588ed734 100644 --- a/Documentation/devicetree/bindings/net/nfc/st-nci.txt +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt new file mode 100644 index 000000000000..525681b6dc39 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt @@ -0,0 +1,31 @@ +* STMicroelectronics SAS. ST NCI NFC Controller + +Required properties: +- compatible: Should be "st,st21nfcb-spi" +- spi-max-frequency: Maximum SPI frequency (<= 10000000). +- interrupt-parent: phandle for the interrupt gpio controller +- interrupts: GPIO interrupt to which the chip is connected +- reset-gpios: Output GPIO pin used to reset the ST21NFCB + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4): + +&mcspi4 { + + status = "okay"; + + st21nfcb: st21nfcb@0 { + + compatible = "st,st21nfcb-spi"; + + clock-frequency = <4000000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + + reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt new file mode 100644 index 000000000000..51f8d2eba8d8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt @@ -0,0 +1,75 @@ +* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) + + +Required properties: +- compatible: Should be "snps,dwc-qos-ethernet-4.10" +- reg: Address and length of the register set for the device +- clocks: Phandles to the reference clock and the bus clock +- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk" + for the bus clock. +- interrupt-parent: Should be the phandle for the interrupt controller + that services interrupts for this device +- interrupts: Should contain the core's combined interrupt signal +- phy-mode: See ethernet.txt file in the same directory + +Optional properties: +- dma-coherent: Present if dma operations are coherent +- mac-address: See ethernet.txt in the same directory +- local-mac-address: See ethernet.txt in the same directory +- snps,en-lpi: If present it enables use of the AXI low-power interface +- snps,write-requests: Number of write requests that the AXI port can issue. + It depends on the SoC configuration. +- snps,read-requests: Number of read requests that the AXI port can issue. + It depends on the SoC configuration. +- snps,burst-map: Bitmap of allowed AXI burst lengts, with the LSB + representing 4, then 8 etc. +- snps,txpbl: DMA Programmable burst length for the TX DMA +- snps,rxpbl: DMA Programmable burst length for the RX DMA +- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during + TX low-power mode. +- phy-handle: See ethernet.txt file in the same directory +- mdio device tree subnode: When the GMAC has a phy connected to its local + mdio, there must be device tree subnode with the following + required properties: + - compatible: Must be "snps,dwc-qos-ethernet-mdio". + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For each phy on the mdio bus, there must be a node with the following + fields: + + - reg: phy id used to communicate to phy. + - device_type: Must be "ethernet-phy". + - fixed-mode device tree subnode: see fixed-link.txt in the same directory + +Examples: +ethernet2@40010000 { + clock-names = "phy_ref_clk", "apb_pclk"; + clocks = <&clkc 17>, <&clkc 15>; + compatible = "snps,dwc-qos-ethernet-4.10"; + interrupt-parent = <&intc>; + interrupts = <0x0 0x1e 0x4>; + reg = <0x40010000 0x4000>; + phy-handle = <&phy2>; + phy-mode = "gmii"; + + snps,en-tx-lpi-clockgating; + snps,en-lpi; + snps,write-requests = <2>; + snps,read-requests = <16>; + snps,burst-map = <0x7>; + snps,txpbl = <8>; + snps,rxpbl = <2>; + + dma-coherent; + + mdio { + #address-cells = <0x1>; + #size-cells = <0x0>; + phy2: phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + device_type = "ethernet-phy"; + reg = <0x1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/panel/auo,b080uan01.txt b/Documentation/devicetree/bindings/panel/auo,b080uan01.txt new file mode 100644 index 000000000000..bae0e2b51467 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/auo,b080uan01.txt @@ -0,0 +1,7 @@ +AU Optronics Corporation 8.0" WUXGA TFT LCD panel + +Required properties: +- compatible: should be "auo,b101ean01" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/lg,lg4573.txt b/Documentation/devicetree/bindings/panel/lg,lg4573.txt new file mode 100644 index 000000000000..824441f4e95a --- /dev/null +++ b/Documentation/devicetree/bindings/panel/lg,lg4573.txt @@ -0,0 +1,19 @@ +LG LG4573 TFT Liquid Crystal Display with SPI control bus + +Required properties: + - compatible: "lg,lg4573" + - reg: address of the panel on the SPI bus + +The panel must obey rules for SPI slave device specified in document [1]. + +[1]: Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + + lcd_panel: display@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "lg,lg4573"; + spi-max-frequency = <10000000>; + reg = <0>; + }; diff --git a/Documentation/devicetree/bindings/panel/nec,nl4827hc19-05b.txt b/Documentation/devicetree/bindings/panel/nec,nl4827hc19-05b.txt new file mode 100644 index 000000000000..8e1914d1edb8 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/nec,nl4827hc19-05b.txt @@ -0,0 +1,7 @@ +NEC LCD Technologies,Ltd. WQVGA TFT LCD panel + +Required properties: +- compatible: should be "nec,nl4827hc19-05b" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/panel/okaya,rs800480t-7x0gp.txt b/Documentation/devicetree/bindings/panel/okaya,rs800480t-7x0gp.txt new file mode 100644 index 000000000000..ddf8e211d382 --- /dev/null +++ b/Documentation/devicetree/bindings/panel/okaya,rs800480t-7x0gp.txt @@ -0,0 +1,7 @@ +OKAYA Electric America, Inc. RS800480T-7X0GP 7" WVGA LCD panel + +Required properties: +- compatible: should be "okaya,rs800480t-7x0gp" + +This binding is compatible with the simple-panel binding, which is specified +in simple-panel.txt in this directory. diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 9462ab7ddd1f..3c821cda1ad0 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -48,7 +48,7 @@ Optional subnode-properties: Examples: -pinctrl@01c20800 { +pio: pinctrl@01c20800 { compatible = "allwinner,sun5i-a13-pinctrl"; reg = <0x01c20800 0x400>; #address-cells = <1>; @@ -68,3 +68,38 @@ pinctrl@01c20800 { allwinner,pull = <0>; }; }; + + +GPIO and interrupt controller +----------------------------- + +This hardware also acts as a GPIO controller and an interrupt +controller. + +Consumers that would want to refer to one or the other (or both) +should provide through the usual *-gpios and interrupts properties a +cell with 3 arguments, first the number of the bank, then the pin +inside that bank, and finally the flags for the GPIO/interrupts. + +Example: + +xio: gpio@38 { + compatible = "nxp,pcf8574a"; + reg = <0x38>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-parent = <&pio>; + interrupts = <6 0 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; +}; + +reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/cnxt,cx92755-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/cnxt,cx92755-pinctrl.txt new file mode 100644 index 000000000000..23ce8dc26990 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/cnxt,cx92755-pinctrl.txt @@ -0,0 +1,86 @@ +Conexant Digicolor CX92755 General Purpose Pin Mapping + +This document describes the device tree binding of the pin mapping hardware +modules in the Conexant Digicolor CX92755 SoCs. The CX92755 in one of the +Digicolor series of SoCs. + +=== Pin Controller Node === + +Required Properties: + +- compatible: Must be "cnxt,cx92755-pinctrl" +- reg: Base address of the General Purpose Pin Mapping register block and the + size of the block. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells: Must be <2>. The first cell is the pin number and the + second cell is used to specify flags. See include/dt-bindings/gpio/gpio.h + for possible values. + +For example, the following is the bare minimum node: + + pinctrl: pinctrl@f0000e20 { + compatible = "cnxt,cx92755-pinctrl"; + reg = <0xf0000e20 0x100>; + gpio-controller; + #gpio-cells = <2>; + }; + +As a pin controller device, in addition to the required properties, this node +should also contain the pin configuration nodes that client devices reference, +if any. + +For a general description of GPIO bindings, please refer to ../gpio/gpio.txt. + +=== Pin Configuration Node === + +Each pin configuration node is a sub-node of the pin controller node and is a +container of an arbitrary number of subnodes, called pin group nodes in this +document. + +Please refer to the pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the definition of a +"pin configuration node". + +=== Pin Group Node === + +A pin group node specifies the desired pin mux for an arbitrary number of +pins. The name of the pin group node is optional and not used. + +A pin group node only affects the properties specified in the node, and has no +effect on any properties that are omitted. + +The pin group node accepts a subset of the generic pin config properties. For +details generic pin config properties, please refer to pinctrl-bindings.txt +and <include/linux/pinctrl/pinconfig-generic.h>. + +Required Pin Group Node Properties: + +- pins: Multiple strings. Specifies the name(s) of one or more pins to be + configured by this node. The format of a pin name string is "GP_xy", where x + is an uppercase character from 'A' to 'R', and y is a digit from 0 to 7. +- function: String. Specifies the pin mux selection. Values must be one of: + "gpio", "client_a", "client_b", "client_c" + +Example: + pinctrl: pinctrl@f0000e20 { + compatible = "cnxt,cx92755-pinctrl"; + reg = <0xf0000e20 0x100>; + + uart0_default: uart0_active { + data_signals { + pins = "GP_O0", "GP_O1"; + function = "client_b"; + }; + }; + }; + + uart0: uart@f0000740 { + compatible = "cnxt,cx92755-usart"; + ... + pinctrl-0 = <&uart0_default>; + pinctrl-names = "default"; + }; + +In the example above, a single pin group configuration node defines the +"client select" for the Rx and Tx signals of uart0. The uart0 node references +that pin configuration node using the &uart0_default phandle. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt index ed19991aad35..d7803a2a94e9 100644 --- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt +++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt @@ -7,8 +7,13 @@ of PMIC's from Qualcomm. Usage: required Value type: <string> Definition: Should contain one of: + "qcom,pm8018-mpp", + "qcom,pm8038-mpp", + "qcom,pm8821-mpp", "qcom,pm8841-mpp", "qcom,pm8916-mpp", + "qcom,pm8917-mpp", + "qcom,pm8921-mpp", "qcom,pm8941-mpp", "qcom,pma8084-mpp", @@ -77,12 +82,9 @@ to specify in a pin configuration subnode: Value type: <string> Definition: Specify the alternative function to be configured for the specified pins. Valid values are: - "normal", - "paired", - "dtest1", - "dtest2", - "dtest3", - "dtest4" + "digital", + "analog", + "sink" - bias-disable: Usage: optional @@ -127,12 +129,18 @@ to specify in a pin configuration subnode: Definition: Selects the power source for the specified pins. Valid power sources are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> -- qcom,analog-mode: +- qcom,analog-level: Usage: optional - Value type: <none> - Definition: Selects Analog mode of operation: combined with input-enable - and/or output-high, output-low MPP could operate as - Bidirectional Logic, Analog Input, Analog Output. + Value type: <u32> + Definition: Selects the source for analog output. Valued values are + defined in <dt-binding/pinctrl/qcom,pmic-mpp.h> + PMIC_MPP_AOUT_LVL_* + +- qcom,dtest: + Usage: optional + Value type: <u32> + Definition: Selects which dtest rail to be routed in the various functions. + Valid values are 1-4 - qcom,amux-route: Usage: optional @@ -140,6 +148,10 @@ to specify in a pin configuration subnode: Definition: Selects the source for analog input. Valid values are defined in <dt-bindings/pinctrl/qcom,pmic-mpp.h> PMIC_MPP_AMUX_ROUTE_CH5, PMIC_MPP_AMUX_ROUTE_CH6... +- qcom,paired: + Usage: optional + Value type: <none> + Definition: Indicates that the pin should be operating in paired mode. Example: @@ -156,7 +168,7 @@ Example: pm8841_default: default { gpio { pins = "mpp1", "mpp2", "mpp3", "mpp4"; - function = "normal"; + function = "digital"; input-enable; power-source = <PM8841_MPP_S3>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 51cee44fc140..9496934528bd 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -58,12 +58,12 @@ are parsed through phandles and processed purely based on their content. Pin Configuration Node Properties: -- renesas,pins : An array of strings, each string containing the name of a pin. -- renesas,groups : An array of strings, each string containing the name of a pin +- pins : An array of strings, each string containing the name of a pin. +- groups : An array of strings, each string containing the name of a pin group. -- renesas,function: A string containing the name of the function to mux to the - pin group(s) specified by the renesas,groups property +- function: A string containing the name of the function to mux to the pin + group(s) specified by the groups property. Valid values for pin, group and function names can be found in the group and function arrays of the PFC data file corresponding to the SoC @@ -71,7 +71,9 @@ Pin Configuration Node Properties: The pin configuration parameters use the generic pinconf bindings defined in pinctrl-bindings.txt in this directory. The supported parameters are -bias-disable, bias-pull-up and bias-pull-down. +bias-disable, bias-pull-up, bias-pull-down and power-source. For pins that +have a configurable I/O voltage, the power-source value should be the +nominal I/O voltage in millivolts. GPIO @@ -141,19 +143,19 @@ Example 3: KZM-A9-GT (SH-Mobile AG5) default pin state hog and pin control maps mmcif_pins: mmcif { mux { - renesas,groups = "mmc0_data8_0", "mmc0_ctrl_0"; - renesas,function = "mmc0"; + groups = "mmc0_data8_0", "mmc0_ctrl_0"; + function = "mmc0"; }; cfg { - renesas,groups = "mmc0_data8_0"; - renesas,pins = "PORT279"; + groups = "mmc0_data8_0"; + pins = "PORT279"; bias-pull-up; }; }; scifa4_pins: scifa4 { - renesas,groups = "scifa4_data", "scifa4_ctrl"; - renesas,function = "scifa4"; + groups = "scifa4_data", "scifa4_ctrl"; + function = "scifa4"; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt index f63fcb3ed352..2213802435e0 100644 --- a/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt +++ b/Documentation/devicetree/bindings/pinctrl/ste,nomadik.txt @@ -3,7 +3,9 @@ ST Ericsson Nomadik pinmux controller Required properties: - compatible: "stericsson,db8500-pinctrl", "stericsson,db8540-pinctrl", "stericsson,stn8815-pinctrl" -- reg: Should contain the register physical address and length of the PRCMU. +- nomadik-gpio-chips: array of phandles to the corresponding GPIO chips + (these have the register ranges used by the pin controller). +- prcm: phandle to the PRCMU managing the back end of this pin controller Please refer to pinctrl-bindings.txt in this directory for details of the common pinctrl bindings used by client devices, including the meaning of the @@ -74,7 +76,8 @@ Example board file extract: pinctrl@80157000 { compatible = "stericsson,db8500-pinctrl"; - reg = <0x80157000 0x2000>; + nomadik-gpio-chips = <&gpio0>, <&gpio1>, <&gpio2>, <&gpio3>; + prcm = <&prcmu>; pinctrl-names = "default"; diff --git a/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt b/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt new file mode 100644 index 000000000000..0532c46b3372 --- /dev/null +++ b/Documentation/devicetree/bindings/powerpc/fsl/scfg.txt @@ -0,0 +1,18 @@ +Freescale Supplement configuration unit (SCFG) + +SCFG is the supplemental configuration unit, that provides SoC specific +configuration and status registers for the chip. Such as getting PEX port +status. + +Required properties: + +- compatible: should be "fsl,<chip>-scfg" +- reg: should contain base address and length of SCFG memory-mapped +registers + +Example: + + scfg: global-utilities@fc000 { + compatible = "fsl,t1040-scfg"; + reg = <0xfc000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/regulator/max77686.txt b/Documentation/devicetree/bindings/regulator/max77686.txt new file mode 100644 index 000000000000..0dded64d89d3 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/max77686.txt @@ -0,0 +1,71 @@ +Binding for Maxim MAX77686 regulators + +This is a part of the device tree bindings of MAX77686 multi-function device. +More information can be found in ../mfd/max77686.txt file. + +The MAX77686 PMIC has 9 high-efficiency Buck and 26 Low-DropOut (LDO) +regulators that can be controlled over I2C. + +Following properties should be present in main device node of the MFD chip. + +Optional node: +- voltage-regulators : The regulators of max77686 have to be instantiated + under subnode named "voltage-regulators" using the following format. + + regulator_name { + regulator-compatible = LDOn/BUCKn + standard regulator constraints.... + }; + refer Documentation/devicetree/bindings/regulator/regulator.txt + + The regulator node's name should be initialized with a string +to get matched with their hardware counterparts as follow: + + -LDOn : for LDOs, where n can lie in range 1 to 26. + example: LDO1, LDO2, LDO26. + -BUCKn : for BUCKs, where n can lie in range 1 to 9. + example: BUCK1, BUCK5, BUCK9. + + Regulators which can be turned off during system suspend: + -LDOn : 2, 6-8, 10-12, 14-16, + -BUCKn : 1-4. + Use standard regulator bindings for it ('regulator-off-in-suspend'). + + LDO20, LDO21, LDO22, BUCK8 and BUCK9 can be configured to GPIO enable + control. To turn this feature on this property must be added to the regulator + sub-node: + - maxim,ena-gpios : one GPIO specifier enable control (the gpio + flags are actually ignored and always + ACTIVE_HIGH is used) + +Example: + + max77686: pmic@09 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 IRQ_TYPE_NONE>; + reg = <0x09>; + + voltage-regulators { + ldo11_reg: LDO11 { + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck9_reg: BUCK9 { + regulator-name = "CAM_ISP_CORE_1.2V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1200000>; + maxim,ena-gpios = <&gpm0 3 GPIO_ACTIVE_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt b/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt index 73407f502e4e..daf88265df32 100644 --- a/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt +++ b/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt @@ -1,20 +1,23 @@ STMicroelectronics Low Power Controller (LPC) - RTC =================================================== -LPC currently supports Watchdog OR Real Time Clock functionality. +LPC currently supports Watchdog OR Real Time Clock OR Clocksource +functionality. [See: ../watchdog/st_lpc_wdt.txt for Watchdog options] +[See: ../timer/st,stih407-lpc for Clocksource options] Required properties -- compatible : Must be one of: "st,stih407-lpc" "st,stih416-lpc" - "st,stih415-lpc" "st,stid127-lpc" +- compatible : Must be: "st,stih407-lpc" - reg : LPC registers base address + size - interrupts : LPC interrupt line number and associated flags - clocks : Clock used by LPC device (See: ../clock/clock-bindings.txt) -- st,lpc-mode : The LPC can run either one of two modes ST_LPC_MODE_RTC [0] or - ST_LPC_MODE_WDT [1]. One (and only one) mode must be - selected. +- st,lpc-mode : The LPC can run either one of three modes: + ST_LPC_MODE_RTC [0] + ST_LPC_MODE_WDT [1] + ST_LPC_MODE_CLKSRC [2] + One (and only one) mode must be selected. Example: lpc@fde05000 { diff --git a/Documentation/devicetree/bindings/sound/cs4349.txt b/Documentation/devicetree/bindings/sound/cs4349.txt new file mode 100644 index 000000000000..54c117b59dba --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4349.txt @@ -0,0 +1,19 @@ +CS4349 audio CODEC + +Required properties: + + - compatible : "cirrus,cs4349" + + - reg : the I2C address of the device for I2C + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. + +Example: + +codec: cs4349@48 { + compatible = "cirrus,cs4349"; + reg = <0x48>; + reset-gpios = <&gpio 54 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/ics43432.txt b/Documentation/devicetree/bindings/sound/ics43432.txt new file mode 100644 index 000000000000..b02e3a6c0fef --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ics43432.txt @@ -0,0 +1,17 @@ +Invensense ICS-43432 MEMS microphone with I2S output. + +There are no software configuration options for this device, indeed, the only +host connection is the I2S interface. Apart from requirements on clock +frequency (460 kHz to 3.379 MHz according to the data sheet) there must be +64 clock cycles in each stereo output frame; 24 of the 32 available bits +contain audio data. A hardware pin determines if the device outputs data +on the left or right channel of the I2S frame. + +Required properties: + - compatible : Must be "invensense,ics43432" + +Example: + + ics43432: ics43432 { + compatible = "invensense,ics43432"; + }; diff --git a/Documentation/devicetree/bindings/sound/max98357a.txt b/Documentation/devicetree/bindings/sound/max98357a.txt index a7a149a236e5..28645a2ff885 100644 --- a/Documentation/devicetree/bindings/sound/max98357a.txt +++ b/Documentation/devicetree/bindings/sound/max98357a.txt @@ -4,7 +4,11 @@ This node models the Maxim MAX98357A DAC. Required properties: - compatible : "maxim,max98357a" -- sdmode-gpios : GPIO specifier for the GPIO -> DAC SDMODE pin + +Optional properties: +- sdmode-gpios : GPIO specifier for the chip's SD_MODE pin. + If this option is not specified then driver does not manage + the pin state (e.g. chip is always on). Example: diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index b6b3a786855f..1173395b5e5c 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -18,6 +18,12 @@ Required properties: - rcar_sound,src : Should contain SRC feature. The number of SRC subnode should be same as HW. see below for detail. +- rcar_sound,ctu : Should contain CTU feature. + The number of CTU subnode should be same as HW. + see below for detail. +- rcar_sound,mix : Should contain MIX feature. + The number of MIX subnode should be same as HW. + see below for detail. - rcar_sound,dvc : Should contain DVC feature. The number of DVC subnode should be same as HW. see below for detail. @@ -90,6 +96,22 @@ rcar_sound: sound@ec500000 { }; }; + rcar_sound,mix { + mix0: mix@0 { }; + mix1: mix@1 { }; + }; + + rcar_sound,ctu { + ctu00: ctu@0 { }; + ctu01: ctu@1 { }; + ctu02: ctu@2 { }; + ctu03: ctu@3 { }; + ctu10: ctu@4 { }; + ctu11: ctu@5 { }; + ctu12: ctu@6 { }; + ctu13: ctu@7 { }; + }; + rcar_sound,src { src0: src@0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt index c64155027288..962748a8d919 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt @@ -6,6 +6,7 @@ Required properties: - compatible : "renesas,rsrc-card,<board>" Examples with soctypes are: + - "renesas,rsrc-card" - "renesas,rsrc-card,lager" - "renesas,rsrc-card,koelsch" Optional properties: @@ -29,6 +30,12 @@ Optional subnode properties: - frame-inversion : bool property. Add this if the dai-link uses frame clock inversion. - convert-rate : platform specified sampling rate convert +- audio-prefix : see audio-routing +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources. + use audio-prefix if some components is using same sink/sources naming. + it can be used if compatible was "renesas,rsrc-card"; Required CPU/CODEC subnodes properties: diff --git a/Documentation/devicetree/bindings/sound/rockchip-max98090.txt b/Documentation/devicetree/bindings/sound/rockchip-max98090.txt new file mode 100644 index 000000000000..a805aa99ad75 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-max98090.txt @@ -0,0 +1,19 @@ +ROCKCHIP with MAX98090 CODEC + +Required properties: +- compatible: "rockchip,rockchip-audio-max98090" +- rockchip,model: The user-visible name of this sound complex +- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's + connected to the CODEC +- rockchip,audio-codec: The phandle of the MAX98090 audio codec +- rockchip,headset-codec: The phandle of Ext chip for jack detection + +Example: + +sound { + compatible = "rockchip,rockchip-audio-max98090"; + rockchip,model = "ROCKCHIP-I2S"; + rockchip,i2s-controller = <&i2s>; + rockchip,audio-codec = <&max98090>; + rockchip,headset-codec = <&headsetcodec>; +}; diff --git a/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt b/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt new file mode 100644 index 000000000000..411a62b3ff41 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt @@ -0,0 +1,17 @@ +ROCKCHIP with RT5645/RT5650 CODECS + +Required properties: +- compatible: "rockchip,rockchip-audio-rt5645" +- rockchip,model: The user-visible name of this sound complex +- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's + connected to the CODEC +- rockchip,audio-codec: The phandle of the RT5645/RT5650 audio codec + +Example: + +sound { + compatible = "rockchip,rockchip-audio-rt5645"; + rockchip,model = "ROCKCHIP-I2S"; + rockchip,i2s-controller = <&i2s>; + rockchip,audio-codec = <&rt5645>; +}; diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt new file mode 100644 index 000000000000..028fa1c82f50 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt @@ -0,0 +1,155 @@ +STMicroelectronics sti ASoC cards + +The sti ASoC Sound Card can be used, for all sti SoCs using internal sti-sas +codec or external codecs. + +sti sound drivers allows to expose sti SoC audio interface through the +generic ASoC simple card. For details about sound card declaration please refer to +Documentation/devicetree/bindings/sound/simple-card.txt. + +1) sti-uniperiph-dai: audio dai device. +--------------------------------------- + +Required properties: + - compatible: "st,sti-uni-player" or "st,sti-uni-reader" + + - st,syscfg: phandle to boot-device system configuration registers + + - clock-names: name of the clocks listed in clocks property in the same order + + - reg: CPU DAI IP Base address and size entries, listed in same + order than the CPU_DAI properties. + + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + + - interrupts: CPU_DAI interrupt line, listed in the same order than the + CPU_DAI properties. + + - dma: CPU_DAI DMA controller phandle and DMA request line, listed in the same + order than the CPU_DAI properties. + + - dma-names: identifier string for each DMA request line in the dmas property. + "tx" for "st,sti-uni-player" compatibility + "rx" for "st,sti-uni-reader" compatibility + + - version: IP version integrated in SOC. + + - dai-name: DAI name that describes the IP. + +Required properties ("st,sti-uni-player" compatibility only): + - clocks: CPU_DAI IP clock source, listed in the same order than the + CPU_DAI properties. + + - uniperiph-id: internal SOC IP instance ID. + + - IP mode: IP working mode depending on associated codec. + "HDMI" connected to HDMI codec IP and IEC HDMI formats. + "SPDIF"connected to SPDIF codec and support SPDIF formats. + "PCM" PCM standard mode for I2S or TDM bus. + +Optional properties: + - pinctrl-0: defined for CPU_DAI@1 and CPU_DAI@4 to describe I2S PIOs for + external codecs connection. + + - pinctrl-names: should contain only one value - "default". + +Example: + + sti_uni_player2: sti-uni-player@2 { + compatible = "st,sti-uni-player"; + status = "okay"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + clocks = <&clk_s_d0_flexgen CLK_PCM_2>; + reg = <0x8D82000 0x158>; + interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; + dmas = <&fdma0 4 0 1>; + dai-name = "Uni Player #1 (DAC)"; + dma-names = "tx"; + uniperiph-id = <2>; + version = <5>; + mode = "PCM"; + }; + + sti_uni_player3: sti-uni-player@3 { + compatible = "st,sti-uni-player"; + status = "okay"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + clocks = <&clk_s_d0_flexgen CLK_SPDIFF>; + reg = <0x8D85000 0x158>; + interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>; + dmas = <&fdma0 7 0 1>; + dma-names = "tx"; + dai-name = "Uni Player #1 (PIO)"; + uniperiph-id = <3>; + version = <5>; + mode = "SPDIF"; + }; + + sti_uni_reader1: sti-uni-reader@1 { + compatible = "st,sti-uni-reader"; + status = "disabled"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + reg = <0x8D84000 0x158>; + interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>; + dmas = <&fdma0 6 0 1>; + dma-names = "rx"; + dai-name = "Uni Reader #1 (HDMI RX)"; + version = <3>; + }; + +2) sti-sas-codec: internal audio codec IPs driver +------------------------------------------------- + +Required properties: + - compatible: "st,sti<chip>-sas-codec" . + Should be chip "st,stih416-sas-codec" or "st,stih407-sas-codec" + + - st,syscfg: phandle to boot-device system configuration registers. + + - pinctrl-0: SPDIF PIO description. + + - pinctrl-names: should contain only one value - "default". + +Example: + sti_sas_codec: sti-sas-codec { + compatible = "st,stih407-sas-codec"; + #sound-dai-cells = <1>; + st,reg_audio = <&syscfg_core>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spdif_out >; + }; + +Example of audio card declaration: + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "sti audio card"; + status = "okay"; + + simple-audio-card,dai-link@0 { + /* DAC */ + format = "i2s"; + dai-tdm-slot-width = <32>; + cpu { + sound-dai = <&sti_uni_player2>; + }; + + codec { + sound-dai = <&sti_sasg_codec 1>; + }; + }; + simple-audio-card,dai-link@1 { + /* SPDIF */ + format = "left_j"; + cpu { + sound-dai = <&sti_uni_player3>; + }; + + codec { + sound-dai = <&sti_sasg_codec 0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/timer/img,pistachio-gptimer.txt b/Documentation/devicetree/bindings/timer/img,pistachio-gptimer.txt new file mode 100644 index 000000000000..7afce80bf6a0 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/img,pistachio-gptimer.txt @@ -0,0 +1,28 @@ +* Pistachio general-purpose timer based clocksource + +Required properties: + - compatible: "img,pistachio-gptimer". + - reg: Address range of the timer registers. + - interrupts: An interrupt for each of the four timers + - clocks: Should contain a clock specifier for each entry in clock-names + - clock-names: Should contain the following entries: + "sys", interface clock + "slow", slow counter clock + "fast", fast counter clock + - img,cr-periph: Must contain a phandle to the peripheral control + syscon node. + +Example: + timer: timer@18102000 { + compatible = "img,pistachio-gptimer"; + reg = <0x18102000 0x100>; + interrupts = <GIC_SHARED 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 61 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 62 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SHARED 63 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_periph PERIPH_CLK_COUNTER_FAST>, + <&clk_periph PERIPH_CLK_COUNTER_SLOW>, + <&cr_periph SYS_CLK_TIMER>; + clock-names = "fast", "slow", "sys"; + img,cr-periph = <&cr_periph>; + }; diff --git a/Documentation/devicetree/bindings/timer/st,stih407-lpc b/Documentation/devicetree/bindings/timer/st,stih407-lpc new file mode 100644 index 000000000000..72acb487b856 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/st,stih407-lpc @@ -0,0 +1,28 @@ +STMicroelectronics Low Power Controller (LPC) - Clocksource +=========================================================== + +LPC currently supports Watchdog OR Real Time Clock OR Clocksource +functionality. + +[See: ../watchdog/st_lpc_wdt.txt for Watchdog options] +[See: ../rtc/rtc-st-lpc.txt for RTC options] + +Required properties + +- compatible : Must be: "st,stih407-lpc" +- reg : LPC registers base address + size +- interrupts : LPC interrupt line number and associated flags +- clocks : Clock used by LPC device (See: ../clock/clock-bindings.txt) +- st,lpc-mode : The LPC can run either one of three modes: + ST_LPC_MODE_RTC [0] + ST_LPC_MODE_WDT [1] + ST_LPC_MODE_CLKSRC [2] + One (and only one) mode must be selected. + +Example: + lpc@fde05000 { + compatible = "st,stih407-lpc"; + reg = <0xfde05000 0x1000>; + clocks = <&clk_s_d3_flexgen CLK_LPC_0>; + st,lpc-mode = <ST_LPC_MODE_CLKSRC>; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 56a6d4e79383..ac5f0c34ae00 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -55,6 +55,7 @@ cortina Cortina Systems, Inc. cosmic Cosmic Circuits crystalfontz Crystalfontz America, Inc. cubietech Cubietech, Ltd. +cypress Cypress Semiconductor Corporation dallas Maxim Integrated Products (formerly Dallas Semiconductor) davicom DAVICOM Semiconductor, Inc. delta Delta Electronics, Inc. @@ -111,6 +112,7 @@ ingenic Ingenic Semiconductor innolux Innolux Corporation intel Intel Corporation intercontrol Inter Control Group +invensense InvenSense Inc. isee ISEE 2007 S.L. isil Intersil jedec JEDEC Solid State Technology Association @@ -143,6 +145,7 @@ mundoreader Mundo Reader S.L. murata Murata Manufacturing Co., Ltd. mxicy Macronix International Co., Ltd. national National Semiconductor +nec NEC LCD Technologies, Ltd. neonode Neonode Inc. netgear NETGEAR netlogic Broadcom Corporation (formerly NetLogic Microsystems) @@ -150,10 +153,13 @@ netxeon Shenzhen Netxeon Technology CO., LTD newhaven Newhaven Display International nintendo Nintendo nokia Nokia +nuvoton Nuvoton Technology Corporation nvidia NVIDIA nxp NXP Semiconductors +okaya Okaya Electric America, Inc. onnn ON Semiconductor Corp. opencores OpenCores.org +option Option NV ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies panasonic Panasonic Corporation diff --git a/Documentation/devicetree/bindings/leds/leds-pm8941-wled.txt b/Documentation/devicetree/bindings/video/backlight/pm8941-wled.txt index a85a964d61f5..424f8444a6cd 100644 --- a/Documentation/devicetree/bindings/leds/leds-pm8941-wled.txt +++ b/Documentation/devicetree/bindings/video/backlight/pm8941-wled.txt @@ -5,10 +5,7 @@ Required properties: - reg: slave address Optional properties: -- label: The label for this led - See Documentation/devicetree/bindings/leds/common.txt -- linux,default-trigger: Default trigger assigned to the LED - See Documentation/devicetree/bindings/leds/common.txt +- label: The name of the backlight device - qcom,cs-out: bool; enable current sink output - qcom,cabc: bool; enable content adaptive backlight control - qcom,ext-gen: bool; use externally generated modulator signal to dim diff --git a/Documentation/devicetree/bindings/video/fsl,dcu.txt b/Documentation/devicetree/bindings/video/fsl,dcu.txt new file mode 100644 index 000000000000..ebf1be9ae393 --- /dev/null +++ b/Documentation/devicetree/bindings/video/fsl,dcu.txt @@ -0,0 +1,22 @@ +Device Tree bindings for Freescale DCU DRM Driver + +Required properties: +- compatible: Should be one of + * "fsl,ls1021a-dcu". + * "fsl,vf610-dcu". + +- reg: Address and length of the register set for dcu. +- clocks: From common clock binding: handle to dcu clock. +- clock-names: From common clock binding: Shall be "dcu". +- big-endian Boolean property, LS1021A DCU registers are big-endian. +- fsl,panel: The phandle to panel node. + +Examples: +dcu: dcu@2ce0000 { + compatible = "fsl,ls1021a-dcu"; + reg = <0x0 0x2ce0000 0x0 0x10000>; + clocks = <&platform_clk 0>; + clock-names = "dcu"; + big-endian; + fsl,panel = <&panel>; +}; diff --git a/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt b/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt index 388c88a01222..039c5ca45577 100644 --- a/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt @@ -1,9 +1,11 @@ STMicroelectronics Low Power Controller (LPC) - Watchdog ======================================================== -LPC currently supports Watchdog OR Real Time Clock functionality. +LPC currently supports Watchdog OR Real Time Clock OR Clocksource +functionality. [See: ../rtc/rtc-st-lpc.txt for RTC options] +[See: ../timer/st,stih407-lpc for Clocksource options] Required properties @@ -12,9 +14,11 @@ Required properties - reg : LPC registers base address + size - interrupts : LPC interrupt line number and associated flags - clocks : Clock used by LPC device (See: ../clock/clock-bindings.txt) -- st,lpc-mode : The LPC can run either one of two modes ST_LPC_MODE_RTC [0] or - ST_LPC_MODE_WDT [1]. One (and only one) mode must be - selected. +- st,lpc-mode : The LPC can run either one of three modes: + ST_LPC_MODE_RTC [0] + ST_LPC_MODE_WDT [1] + ST_LPC_MODE_CLKSRC [2] + One (and only one) mode must be selected. Required properties [watchdog mode] |
