diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/arizona.txt | 13 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/axp20x.txt | 32 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/cros-ec.txt | 4 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/da9063.txt | 18 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/max77686.txt | 2 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/max77693.txt | 67 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt | 25 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt | 38 |
8 files changed, 191 insertions, 8 deletions
diff --git a/Documentation/devicetree/bindings/mfd/arizona.txt b/Documentation/devicetree/bindings/mfd/arizona.txt index 7665aa95979f..64fa3b2de6cd 100644 --- a/Documentation/devicetree/bindings/mfd/arizona.txt +++ b/Documentation/devicetree/bindings/mfd/arizona.txt @@ -10,6 +10,9 @@ Required properties: "wlf,wm5110" "wlf,wm8280" "wlf,wm8997" + "wlf,wm8998" + "wlf,wm1814" + - reg : I2C slave address when connected using I2C, chip select number when using SPI. @@ -31,10 +34,10 @@ Required properties: as covered in Documentation/devicetree/bindings/regulator/regulator.txt - DBVDD2-supply, DBVDD3-supply : Additional databus power supplies (wm5102, - wm5110, wm8280) + wm5110, wm8280, wm8998, wm1814) - SPKVDDL-supply, SPKVDDR-supply : Speaker driver power supplies (wm5102, - wm5110, wm8280) + wm5110, wm8280, wm8998, wm1814) - SPKVDD-supply : Speaker driver power supply (wm8997) @@ -53,8 +56,10 @@ Optional properties: of input signals. Valid values are 0 (Differential), 1 (Single-ended) and 2 (Digital Microphone). If absent, INn_MODE registers set to 0 by default. If present, values must be specified less than or equal to the number of - input singals. If values less than the number of input signals, elements - that has not been specifed are set to 0 by default. + input signals. If values less than the number of input signals, elements + that have not been specified are set to 0 by default. Entries are: + <IN1, IN2, IN3, IN4> (wm5102, wm5110, wm8280, wm8997) + <IN1A, IN2A, IN1B, IN2B> (wm8998, wm1814) - wlf,dmic-ref : DMIC reference voltage source for each input, can be selected from either MICVDD or one of the MICBIAS's, defines diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt index 98685f291a72..753f14f46e85 100644 --- a/Documentation/devicetree/bindings/mfd/axp20x.txt +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -1,15 +1,16 @@ -AXP202/AXP209 device tree bindings +AXP family PMIC device tree bindings The axp20x family current members : axp202 (X-Powers) axp209 (X-Powers) +axp221 (X-Powers) Required properties: -- compatible: "x-powers,axp202" or "x-powers,axp209" +- compatible: "x-powers,axp202", "x-powers,axp209", "x-powers,axp221" - reg: The I2C slave address for the AXP chip - interrupt-parent: The parent interrupt controller - interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin -- interrupt-controller: axp20x has its own internal IRQs +- interrupt-controller: The PMIC has its own internal IRQs - #interrupt-cells: Should be set to 1 Optional properties: @@ -48,6 +49,31 @@ LDO3 : LDO : ldo3in-supply LDO4 : LDO : ldo24in-supply : shared supply LDO5 : LDO : ldo5in-supply +AXP221 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply +DC1SW : On/Off Switch : dcdc1-supply : DCDC1 secondary output +DC5LDO : LDO : dcdc5-supply : input from DCDC5 +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +DLDO3 : LDO : dldoin-supply : shared supply +DLDO4 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on + Example: axp209: pmic@34 { diff --git a/Documentation/devicetree/bindings/mfd/cros-ec.txt b/Documentation/devicetree/bindings/mfd/cros-ec.txt index 8009c3d87f33..1777916e9e28 100644 --- a/Documentation/devicetree/bindings/mfd/cros-ec.txt +++ b/Documentation/devicetree/bindings/mfd/cros-ec.txt @@ -18,6 +18,10 @@ Required properties (SPI): - reg: SPI chip select Optional properties (SPI): +- google,cros-ec-spi-pre-delay: Some implementations of the EC need a little + time to wake up from sleep before they can receive SPI transfers at a high + clock rate. This property specifies the delay, in usecs, between the + assertion of the CS to the start of the first clock pulse. - google,cros-ec-spi-msg-delay: Some implementations of the EC require some additional processing time in order to accept new transactions. If the delay between transactions is not long enough the EC may not be able to respond diff --git a/Documentation/devicetree/bindings/mfd/da9063.txt b/Documentation/devicetree/bindings/mfd/da9063.txt index 42c6fa6f1c9a..05b21bcb8543 100644 --- a/Documentation/devicetree/bindings/mfd/da9063.txt +++ b/Documentation/devicetree/bindings/mfd/da9063.txt @@ -5,6 +5,7 @@ DA9093 consists of a large and varied group of sub-devices (I2C Only): Device Supply Names Description ------ ------------ ----------- da9063-regulator : : LDOs & BUCKs +da9063-onkey : : On Key da9063-rtc : : Real-Time Clock da9063-watchdog : : Watchdog @@ -51,6 +52,18 @@ Sub-nodes: the DA9063. There are currently no entries in this binding, however compatible = "dlg,da9063-rtc" should be added if a node is created. +- onkey : This node defines the OnKey settings for controlling the key + functionality of the device. The node should contain the compatible property + with the value "dlg,da9063-onkey". + + Optional onkey properties: + + - dlg,disable-key-power : Disable power-down using a long key-press. If this + entry exists the OnKey driver will remove support for the KEY_POWER key + press. If this entry does not exist then by default the key-press + triggered power down is enabled and the OnKey will support both KEY_POWER + and KEY_SLEEP. + - watchdog : This node defines settings for the Watchdog timer associated with the DA9063. There are currently no entries in this binding, however compatible = "dlg,da9063-watchdog" should be added if a node is created. @@ -73,6 +86,11 @@ Example: compatible = "dlg,da9063-watchdog"; }; + onkey { + compatible = "dlg,da9063-onkey"; + dlg,disable-key-power; + }; + regulators { DA9063_BCORE1: bcore1 { regulator-name = "BCORE1"; diff --git a/Documentation/devicetree/bindings/mfd/max77686.txt b/Documentation/devicetree/bindings/mfd/max77686.txt index e39f0bc1f55e..163bd81a4607 100644 --- a/Documentation/devicetree/bindings/mfd/max77686.txt +++ b/Documentation/devicetree/bindings/mfd/max77686.txt @@ -1,6 +1,6 @@ Maxim MAX77686 multi-function device -MAX77686 is a Mulitifunction device with PMIC, RTC and Charger on chip. It is +MAX77686 is a Multifunction device with PMIC, RTC and Charger on chip. It is interfaced to host controller using i2c interface. PMIC and Charger submodules are addressed using same i2c slave address whereas RTC submodule uses different i2c slave address,presently for which we are statically creating i2c diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt index 38e64405e98d..d3425846aa5b 100644 --- a/Documentation/devicetree/bindings/mfd/max77693.txt +++ b/Documentation/devicetree/bindings/mfd/max77693.txt @@ -76,7 +76,60 @@ Optional properties: Valid values: 4300000, 4700000, 4800000, 4900000 Default: 4300000 +- led : the LED submodule device node + +There are two LED outputs available - FLED1 and FLED2. Each of them can +control a separate LED or they can be connected together to double +the maximum current for a single connected LED. One LED is represented +by one child node. + +Required properties: +- compatible : Must be "maxim,max77693-led". + +Optional properties: +- maxim,boost-mode : + In boost mode the device can produce up to 1.2A of total current + on both outputs. The maximum current on each output is reduced + to 625mA then. If not enabled explicitly, boost setting defaults to + LEDS_BOOST_FIXED in case both current sources are used. + Possible values: + LEDS_BOOST_OFF (0) - no boost, + LEDS_BOOST_ADAPTIVE (1) - adaptive mode, + LEDS_BOOST_FIXED (2) - fixed mode. +- maxim,boost-mvout : Output voltage of the boost module in millivolts. + Valid values: 3300 - 5500, step by 25 (rounded down) + Default: 3300 +- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired + if chip estimates that system voltage could drop below this level due + to flash power consumption. + Valid values: 2400 - 3400, step by 33 (rounded down) + Default: 2400 + +Required properties for the LED child node: +- led-sources : see Documentation/devicetree/bindings/leds/common.txt; + device current output identifiers: 0 - FLED1, 1 - FLED2 +- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + Valid values for a LED connected to one FLED output: + 15625 - 250000, step by 15625 (rounded down) + Valid values for a LED connected to both FLED outputs: + 15625 - 500000, step by 15625 (rounded down) +- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt + Valid values for a single LED connected to one FLED output + (boost mode must be turned off): + 15625 - 1000000, step by 15625 (rounded down) + Valid values for a single LED connected to both FLED outputs: + 15625 - 1250000, step by 15625 (rounded down) + Valid values for two LEDs case: + 15625 - 625000, step by 15625 (rounded down) +- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt + Valid values: 62500 - 1000000, step by 62500 (rounded down) + +Optional properties for the LED child node: +- label : see Documentation/devicetree/bindings/leds/common.txt + Example: +#include <dt-bindings/leds/common.h> + max77693@66 { compatible = "maxim,max77693"; reg = <0x66>; @@ -117,5 +170,19 @@ Example: maxim,thermal-regulation-celsius = <75>; maxim,battery-overcurrent-microamp = <3000000>; maxim,charge-input-threshold-microvolt = <4300000>; + + led { + compatible = "maxim,max77693-led"; + maxim,boost-mode = <LEDS_BOOST_FIXED>; + maxim,boost-mvout = <5000>; + maxim,mvsys-min = <2400>; + + camera_flash: flash-led { + label = "max77693-flash"; + led-sources = <0>, <1>; + led-max-microamp = <500000>; + flash-max-microamp = <1250000>; + flash-max-timeout-us = <1000000>; + }; }; }; diff --git a/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt b/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt new file mode 100644 index 000000000000..73407f502e4e --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-st-lpc.txt @@ -0,0 +1,25 @@ +STMicroelectronics Low Power Controller (LPC) - RTC +=================================================== + +LPC currently supports Watchdog OR Real Time Clock functionality. + +[See: ../watchdog/st_lpc_wdt.txt for Watchdog options] + +Required properties + +- compatible : Must be one of: "st,stih407-lpc" "st,stih416-lpc" + "st,stih415-lpc" "st,stid127-lpc" +- reg : LPC registers base address + size +- interrupts : LPC interrupt line number and associated flags +- clocks : Clock used by LPC device (See: ../clock/clock-bindings.txt) +- st,lpc-mode : The LPC can run either one of two modes ST_LPC_MODE_RTC [0] or + ST_LPC_MODE_WDT [1]. One (and only one) mode must be + selected. + +Example: + lpc@fde05000 { + compatible = "st,stih407-lpc"; + reg = <0xfde05000 0x1000>; + clocks = <&clk_s_d3_flexgen CLK_LPC_0>; + st,lpc-mode = <ST_LPC_MODE_RTC>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt b/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt new file mode 100644 index 000000000000..388c88a01222 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/st_lpc_wdt.txt @@ -0,0 +1,38 @@ +STMicroelectronics Low Power Controller (LPC) - Watchdog +======================================================== + +LPC currently supports Watchdog OR Real Time Clock functionality. + +[See: ../rtc/rtc-st-lpc.txt for RTC options] + +Required properties + +- compatible : Must be one of: "st,stih407-lpc" "st,stih416-lpc" + "st,stih415-lpc" "st,stid127-lpc" +- reg : LPC registers base address + size +- interrupts : LPC interrupt line number and associated flags +- clocks : Clock used by LPC device (See: ../clock/clock-bindings.txt) +- st,lpc-mode : The LPC can run either one of two modes ST_LPC_MODE_RTC [0] or + ST_LPC_MODE_WDT [1]. One (and only one) mode must be + selected. + +Required properties [watchdog mode] + +- st,syscfg : Phandle to syscfg node used to enable watchdog and configure + CPU reset type. +- timeout-sec : Watchdog timeout in seconds + +Optional properties [watchdog mode] + +- st,warm-reset : If present reset type will be 'warm' - if not it will be cold + +Example: + lpc@fde05000 { + compatible = "st,stih407-lpc"; + reg = <0xfde05000 0x1000>; + clocks = <&clk_s_d3_flexgen CLK_LPC_0>; + st,syscfg = <&syscfg_core>; + timeout-sec = <120>; + st,lpc-mode = <ST_LPC_MODE_WDT>; + st,warm-reset; + }; |
