diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi')
12 files changed, 101 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index aad527b357a0..523341a0e113 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -2,11 +2,21 @@ (CSPI/eCSPI) for i.MX Required properties: -- compatible : Should be "fsl,<soc>-cspi" or "fsl,<soc>-ecspi" +- compatible : + - "fsl,imx1-cspi" for SPI compatible with the one integrated on i.MX1 + - "fsl,imx21-cspi" for SPI compatible with the one integrated on i.MX21 + - "fsl,imx27-cspi" for SPI compatible with the one integrated on i.MX27 + - "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31 + - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35 + - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt - fsl,spi-num-chipselects : Contains the number of the chipselect - cs-gpios : Specifies the gpio pins to be used for chipselects. +- clocks : Clock specifiers for both ipg and per clocks. +- clock-names : Clock names should include both "ipg" and "per" +See the clock consumer binding, + Documentation/devicetree/bindings/clock/clock-bindings.txt - dmas: DMA specifiers for tx and rx dma. See the DMA client binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: DMA request names should include "tx" and "rx" if present. diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt index e2c88df2cc15..5c090771c016 100644 --- a/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt +++ b/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt @@ -33,6 +33,11 @@ Optional properties: nodes. If unspecified, a single SPI device without a chip select can be used. +- dmas: Two DMA channel specifiers following the convention outlined + in bindings/dma/dma.txt +- dma-names: Names for the dma channels, if present. There must be at + least one channel named "tx" for transmit and named "rx" for + receive. SPI slave nodes must be children of the SPI master node and can contain properties described in Documentation/devicetree/bindings/spi/spi-bus.txt @@ -51,6 +56,9 @@ Example: clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_bam 13>, <&blsp1_bam 12>; + dma-names = "rx", "tx"; + pinctrl-names = "default"; pinctrl-0 = <&spi8_default>; diff --git a/Documentation/devicetree/bindings/spi/sh-msiof.txt b/Documentation/devicetree/bindings/spi/sh-msiof.txt index 4c388bb2f0a2..8f771441be60 100644 --- a/Documentation/devicetree/bindings/spi/sh-msiof.txt +++ b/Documentation/devicetree/bindings/spi/sh-msiof.txt @@ -60,7 +60,7 @@ Example: msiof0: spi@e6e20000 { compatible = "renesas,msiof-r8a7791"; - reg = <0 0xe6e20000 0 0x0064>, <0 0xe7e20000 0 0x0064>; + reg = <0 0xe6e20000 0 0x0064>; interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp0_clks R8A7791_CLK_MSIOF0>; dmas = <&dmac0 0x51>, <&dmac0 0x52>; diff --git a/Documentation/devicetree/bindings/spi/spi-ath79.txt b/Documentation/devicetree/bindings/spi/spi-ath79.txt new file mode 100644 index 000000000000..f1ad9c367532 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-ath79.txt @@ -0,0 +1,24 @@ +Binding for Qualcomm Atheros AR7xxx/AR9xxx SPI controller + +Required properties: +- compatible: has to be "qca,<soc-type>-spi", "qca,ar7100-spi" as fallback. +- reg: Base address and size of the controllers memory area +- clocks: phandle to the AHB clock. +- clock-names: has to be "ahb". +- #address-cells: <1>, as required by generic SPI binding. +- #size-cells: <0>, also as required by generic SPI binding. + +Child nodes as per the generic SPI binding. + +Example: + + spi@1F000000 { + compatible = "qca,ar9132-spi", "qca,ar7100-spi"; + reg = <0x1F000000 0x10>; + + clocks = <&pll 2>; + clock-names = "ahb"; + + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt index cbbe16ed3874..fa77f874e321 100644 --- a/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt +++ b/Documentation/devicetree/bindings/spi/spi-fsl-dspi.txt @@ -1,7 +1,7 @@ ARM Freescale DSPI controller Required properties: -- compatible : "fsl,vf610-dspi" +- compatible : "fsl,vf610-dspi", "fsl,ls1021a-v1.0-dspi", "fsl,ls2085a-dspi" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI controller interrupt - clocks: from common clock binding: handle to dspi clock. @@ -16,6 +16,12 @@ Optional property: in big endian mode, otherwise in native mode(same with CPU), for more detail please see: Documentation/devicetree/bindings/regmap/regmap.txt. +Optional SPI slave node properties: +- fsl,spi-cs-sck-delay: a delay in nanoseconds between activating chip + select and the start of clock signal, at the start of a transfer. +- fsl,spi-sck-cs-delay: a delay in nanoseconds between stopping the clock + signal and deactivating chip select, at the end of a transfer. + Example: dspi0@4002c000 { @@ -43,6 +49,8 @@ dspi0@4002c000 { reg = <0>; linux,modalias = "m25p80"; modal = "at26df081a"; + fsl,spi-cs-sck-delay = <100>; + fsl,spi-sck-cs-delay = <50>; }; }; diff --git a/Documentation/devicetree/bindings/spi/spi-img-spfi.txt b/Documentation/devicetree/bindings/spi/spi-img-spfi.txt index c7dd50fb8eb2..e02fbf18c82c 100644 --- a/Documentation/devicetree/bindings/spi/spi-img-spfi.txt +++ b/Documentation/devicetree/bindings/spi/spi-img-spfi.txt @@ -14,6 +14,7 @@ Required properties: - dma-names: Must include the following entries: - rx - tx +- cs-gpios: Must specify the GPIOs used for chipselect lines. - #address-cells: Must be 1. - #size-cells: Must be 0. diff --git a/Documentation/devicetree/bindings/spi/spi-orion.txt b/Documentation/devicetree/bindings/spi/spi-orion.txt index 50c3a3de61c1..98bc69815eb3 100644 --- a/Documentation/devicetree/bindings/spi/spi-orion.txt +++ b/Documentation/devicetree/bindings/spi/spi-orion.txt @@ -1,7 +1,13 @@ Marvell Orion SPI device Required properties: -- compatible : should be "marvell,orion-spi" or "marvell,armada-370-spi". +- compatible : should be on of the following: + - "marvell,orion-spi" for the Orion, mv78x00, Kirkwood and Dove SoCs + - "marvell,armada-370-spi", for the Armada 370 SoCs + - "marvell,armada-375-spi", for the Armada 375 SoCs + - "marvell,armada-380-spi", for the Armada 38x SoCs + - "marvell,armada-390-spi", for the Armada 39x SoCs + - "marvell,armada-xp-spi", for the Armada XP SoCs - reg : offset and length of the register set for the device - cell-index : Which of multiple SPI controllers is this. Optional properties: diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 467dec441c62..0c491bda4c65 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -24,6 +24,9 @@ Optional Properties: - dmas: DMA specifiers for tx and rx dma. See the DMA client binding, Documentation/devicetree/bindings/dma/dma.txt - dma-names: DMA request names should include "tx" and "rx" if present. +- rx-sample-delay-ns: nanoseconds to delay after the SCLK edge before sampling + Rx data (may need to be fine tuned for high capacitance lines). + No delay (0) by default. Example: @@ -33,6 +36,7 @@ Example: reg = <0xff110000 0x1000>; dmas = <&pdma1 11>, <&pdma1 12>; dma-names = "tx", "rx"; + rx-sample-delay-ns = <10>; #address-cells = <1>; #size-cells = <0>; interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/spi/spi-sirf.txt b/Documentation/devicetree/bindings/spi/spi-sirf.txt index 4c7adb8f777c..ddd78ff68fae 100644 --- a/Documentation/devicetree/bindings/spi/spi-sirf.txt +++ b/Documentation/devicetree/bindings/spi/spi-sirf.txt @@ -1,7 +1,8 @@ * CSR SiRFprimaII Serial Peripheral Interface Required properties: -- compatible : Should be "sirf,prima2-spi" +- compatible : Should be "sirf,prima2-spi", "sirf,prima2-usp" + or "sirf,atlas7-usp" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI interrupt - resets: phandle to the reset controller asserting this device in diff --git a/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.txt b/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.txt new file mode 100644 index 000000000000..c8f50e5cf70b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-zynqmp-qspi.txt @@ -0,0 +1,26 @@ +Xilinx Zynq UltraScale+ MPSoC GQSPI controller Device Tree Bindings +------------------------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,zynqmp-qspi-1.0". +- reg : Physical base address and size of GQSPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller. +- clock-names : List of input clock names - "ref_clk", "pclk" + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). + +Optional properties: +- num-cs : Number of chip selects used. + +Example: + qspi: spi@ff0f0000 { + compatible = "xlnx,zynqmp-qspi-1.0"; + clock-names = "ref_clk", "pclk"; + clocks = <&misc_clk &misc_clk>; + interrupts = <0 15 4>; + interrupt-parent = <&gic>; + num-cs = <1>; + reg = <0x0 0xff0f0000 0x1000>,<0x0 0xc0000000 0x8000000>; + }; diff --git a/Documentation/devicetree/bindings/spi/spi_atmel.txt b/Documentation/devicetree/bindings/spi/spi_atmel.txt index 4f8184d069cb..fb588b3e6a9a 100644 --- a/Documentation/devicetree/bindings/spi/spi_atmel.txt +++ b/Documentation/devicetree/bindings/spi/spi_atmel.txt @@ -4,11 +4,16 @@ Required properties: - compatible : should be "atmel,at91rm9200-spi". - reg: Address and length of the register set for the device - interrupts: Should contain spi interrupt -- cs-gpios: chipselects +- cs-gpios: chipselects (optional for SPI controller version >= 2 with the + Chip Select Active After Transfer feature). - clock-names: tuple listing input clock names. Required elements: "spi_clk" - clocks: phandles to input clocks. +Optional properties: +- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO + capable SPI controllers. + Example: spi1: spi@fffcc000 { @@ -20,6 +25,7 @@ spi1: spi@fffcc000 { clocks = <&spi1_clk>; clock-names = "spi_clk"; cs-gpios = <&pioB 3 0>; + atmel,fifo-size = <32>; status = "okay"; mmc-slot@0 { diff --git a/Documentation/devicetree/bindings/spi/spi_pl022.txt b/Documentation/devicetree/bindings/spi/spi_pl022.txt index 22ed6797216d..4d1673ca8cf8 100644 --- a/Documentation/devicetree/bindings/spi/spi_pl022.txt +++ b/Documentation/devicetree/bindings/spi/spi_pl022.txt @@ -4,9 +4,9 @@ Required properties: - compatible : "arm,pl022", "arm,primecell" - reg : Offset and length of the register set for the device - interrupts : Should contain SPI controller interrupt +- num-cs : total number of chipselects Optional properties: -- num-cs : total number of chipselects - cs-gpios : should specify GPIOs used for chipselects. The gpios will be referred to as reg = <index> in the SPI child nodes. If unspecified, a single SPI device without a chip select can be used. |
