diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
| -rw-r--r-- | Documentation/devicetree/bindings/net/dsa/ksz.txt | 1 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/fsl-fec.txt | 30 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/macb.txt | 4 |
3 files changed, 20 insertions, 15 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt index 4ac21cef370e..113e7ac79aad 100644 --- a/Documentation/devicetree/bindings/net/dsa/ksz.txt +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -12,6 +12,7 @@ Required properties: - "microchip,ksz8565" - "microchip,ksz9893" - "microchip,ksz9563" + - "microchip,ksz8563" Optional properties: diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt index 2d41fb96ce0a..5b88fae0307d 100644 --- a/Documentation/devicetree/bindings/net/fsl-fec.txt +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -7,18 +7,6 @@ Required properties: - phy-mode : See ethernet.txt file in the same directory Optional properties: -- phy-reset-gpios : Should specify the gpio for phy reset -- phy-reset-duration : Reset duration in milliseconds. Should present - only if property "phy-reset-gpios" is available. Missing the property - will have the duration be 1 millisecond. Numbers greater than 1000 are - invalid and 1 millisecond will be used instead. -- phy-reset-active-high : If present then the reset sequence using the GPIO - specified in the "phy-reset-gpios" property is reversed (H=reset state, - L=operation state). -- phy-reset-post-delay : Post reset delay in milliseconds. If present then - a delay of phy-reset-post-delay milliseconds will be observed after the - phy-reset-gpios has been toggled. Can be omitted thus no delay is - observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. - phy-supply : regulator that powers the Ethernet PHY. - phy-handle : phandle to the PHY device connected to this device. - fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. @@ -47,11 +35,27 @@ Optional properties: For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse per second interrupt associated with 1588 precision time protocol(PTP). - Optional subnodes: - mdio : specifies the mdio bus in the FEC, used as a container for phy nodes according to phy.txt in the same directory +Deprecated optional properties: + To avoid these, create a phy node according to phy.txt in the same + directory, and point the fec's "phy-handle" property to it. Then use + the phy's reset binding, again described by phy.txt. +- phy-reset-gpios : Should specify the gpio for phy reset +- phy-reset-duration : Reset duration in milliseconds. Should present + only if property "phy-reset-gpios" is available. Missing the property + will have the duration be 1 millisecond. Numbers greater than 1000 are + invalid and 1 millisecond will be used instead. +- phy-reset-active-high : If present then the reset sequence using the GPIO + specified in the "phy-reset-gpios" property is reversed (H=reset state, + L=operation state). +- phy-reset-post-delay : Post reset delay in milliseconds. If present then + a delay of phy-reset-post-delay milliseconds will be observed after the + phy-reset-gpios has been toggled. Can be omitted thus no delay is + observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. + Example: ethernet@83fec000 { diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt index 63c73fafe26d..0b61a90f1592 100644 --- a/Documentation/devicetree/bindings/net/macb.txt +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -15,10 +15,10 @@ Required properties: Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC. - Use "sifive,fu540-macb" for SiFive FU540-C000 SoC. + Use "sifive,fu540-c000-gem" for SiFive FU540-C000 SoC. Or the generic form: "cdns,emac". - reg: Address and length of the register set for the device - For "sifive,fu540-macb", second range is required to specify the + For "sifive,fu540-c000-gem", second range is required to specify the address and length of the registers for GEMGXL Management block. - interrupts: Should contain macb interrupt - phy-mode: See ethernet.txt file in the same directory. |
