diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc')
5 files changed, 155 insertions, 10 deletions
diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt new file mode 100644 index 000000000000..72cc9cc95880 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-iproc.txt @@ -0,0 +1,23 @@ +Broadcom IPROC SDHCI controller + +This file documents differences between the core properties described +by mmc.txt and the properties that represent the IPROC SDHCI controller. + +Required properties: +- compatible : Should be "brcm,sdhci-iproc-cygnus". +- clocks : The clock feeding the SDHCI controller. + +Optional properties: + - sdhci,auto-cmd12: specifies that controller should use auto CMD12. + +Example: + +sdhci0: sdhci@0x18041000 { + compatible = "brcm,sdhci-iproc-cygnus"; + reg = <0x18041000 0x100>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&lcpll0_clks BCM_CYGNUS_LCPLL0_SDIO_CLK>; + bus-width = <4>; + sdhci,auto-cmd12; + no-1-8-v; +}; diff --git a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt index ee4fc0576c7d..aad98442788b 100644 --- a/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt +++ b/Documentation/devicetree/bindings/mmc/exynos-dw-mshc.txt @@ -36,6 +36,8 @@ Required Properties: in transmit mode and CIU clock phase shift value in receive mode for double data rate mode operation. Refer notes below for the order of the cells and the valid values. +* samsung,dw-mshc-hs400-timing: Specifies the value of CIU TX and RX clock phase + shift value for hs400 mode operation. Notes for the sdr-timing and ddr-timing values: @@ -50,6 +52,9 @@ Required Properties: - if CIU clock divider value is 0 (that is divide by 1), both tx and rx phase shift clocks should be 0. +* samsung,read-strobe-delay: RCLK (Data strobe) delay to control HS400 mode + (Latency value for delay line in Read path) + Required properties for a slot (Deprecated - Recommend to use one slot per host): * gpios: specifies a list of gpios used for command, clock and data bus. The @@ -82,5 +87,7 @@ Example: samsung,dw-mshc-ciu-div = <3>; samsung,dw-mshc-sdr-timing = <2 3>; samsung,dw-mshc-ddr-timing = <1 2>; + samsung,dw-mshc-hs400-timing = <0 2>; + samsung,read-strobe-delay = <90>; bus-width = <8>; }; diff --git a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt index 9046ba06c47a..415c5575cbf7 100644 --- a/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt +++ b/Documentation/devicetree/bindings/mmc/fsl-imx-esdhc.txt @@ -17,6 +17,10 @@ Optional properties: to select a proper data sampling window in case the clock quality is not good due to signal path is too long on the board. Please refer to eSDHC/uSDHC chapter, DLL (Delay Line) section in RM for details. +- voltage-ranges : Specify the voltage range in case there are software + transparent level shifters on the outputs of the controller. Two cells are + required, first cell specifies minimum slot voltage (mV), second cell + specifies maximum slot voltage (mV). Several ranges could be specified. Examples: diff --git a/Documentation/devicetree/bindings/mmc/mmc-card.txt b/Documentation/devicetree/bindings/mmc/mmc-card.txt new file mode 100644 index 000000000000..a70fcd65b9ea --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/mmc-card.txt @@ -0,0 +1,31 @@ +mmc-card / eMMC bindings +------------------------ + +This documents describes the devicetree bindings for a mmc-host controller +child node describing a mmc-card / an eMMC, see "Use of Function subnodes" +in mmc.txt + +Required properties: +-compatible : Must be "mmc-card" +-reg : Must be <0> + +Optional properties: +-broken-hpi : Use this to indicate that the mmc-card has a broken hpi + implementation, and that hpi should not be used + +Example: + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins_a>; + vmmc-supply = <®_vcc3v3>; + bus-width = <8>; + non-removable; + status = "okay"; + + mmccard: mmccard@0 { + reg = <0>; + compatible = "mmc-card"; + broken-hpi; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/sdhci-st.txt b/Documentation/devicetree/bindings/mmc/sdhci-st.txt index 7527db447a35..18d950df2749 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-st.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-st.txt @@ -5,20 +5,62 @@ Documentation/devicetree/bindings/mmc/mmc.txt and the properties used by the sdhci-st driver. Required properties: -- compatible : Must be "st,sdhci" -- clock-names : Should be "mmc" - See: Documentation/devicetree/bindings/resource-names.txt -- clocks : Phandle of the clock used by the sdhci controler - See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- compatible: Must be "st,sdhci" and it can be compatible to "st,sdhci-stih407" + to set the internal glue logic used for configuring the MMC + subsystem (mmcss) inside the FlashSS (available in STiH407 SoC + family). + +- clock-names: Should be "mmc". + See: Documentation/devicetree/bindings/resource-names.txt +- clocks: Phandle to the clock. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt + +- interrupts: One mmc interrupt should be described here. +- interrupt-names: Should be "mmcirq". + +- pinctrl-names: A pinctrl state names "default" must be defined. +- pinctrl-0: Phandle referencing pin configuration of the sd/emmc controller. + See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt + +- reg: This must provide the host controller base address and it can also + contain the FlashSS Top register for TX/RX delay used by the driver + to configure DLL inside the flashSS, if so reg-names must also be + specified. Optional properties: -- non-removable: non-removable slot - See: Documentation/devicetree/bindings/mmc/mmc.txt -- bus-width: Number of data lines - See: Documentation/devicetree/bindings/mmc/mmc.txt +- reg-names: Should be "mmc" and "top-mmc-delay". "top-mmc-delay" is optional + for eMMC on stih407 family silicon to configure DLL inside FlashSS. + +- non-removable: Non-removable slot. Also used for configuring mmcss in STiH407 SoC + family. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- bus-width: Number of data lines. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- max-frequency: Can be 200MHz, 100Mz or 50MHz (default) and used for + configuring the CCONFIG3 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- resets: Phandle and reset specifier pair to softreset line of HC IP. + See: Documentation/devicetree/bindings/reset/reset.txt + +- vqmmc-supply: Phandle to the regulator dt node, mentioned as the vcc/vdd + supply in eMMC/SD specs. + +- sd-uhs--sdr50: To enable the SDR50 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- sd-uhs-sdr104: To enable the SDR104 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. + +- sd-uhs-ddr50: To enable the DDR50 in the mmcss. + See: Documentation/devicetree/bindings/mmc/mmc.txt. Example: +/* Example stih416e eMMC configuration */ + mmc0: sdhci@fe81e000 { compatible = "st,sdhci"; status = "disabled"; @@ -29,5 +71,43 @@ mmc0: sdhci@fe81e000 { pinctrl-0 = <&pinctrl_mmc0>; clock-names = "mmc"; clocks = <&clk_s_a1_ls 1>; - bus-width = <8> + bus-width = <8> + +/* Example SD stih407 family configuration */ + +mmc1: sdhci@09080000 { + compatible = "st,sdhci-stih407", "st,sdhci"; + status = "disabled"; + reg = <0x09080000 0x7ff>; + reg-names = "mmc"; + interrupts = <GIC_SPI 90 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sd1>; + clock-names = "mmc"; + clocks = <&clk_s_c0_flexgen CLK_MMC_1>; + resets = <&softreset STIH407_MMC1_SOFTRESET>; + bus-width = <4>; +}; + +/* Example eMMC stih407 family configuration */ + +mmc0: sdhci@09060000 { + compatible = "st,sdhci-stih407", "st,sdhci"; + status = "disabled"; + reg = <0x09060000 0x7ff>, <0x9061008 0x20>; + reg-names = "mmc", "top-mmc-delay"; + interrupts = <GIC_SPI 92 IRQ_TYPE_NONE>; + interrupt-names = "mmcirq"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mmc0>; + clock-names = "mmc"; + clocks = <&clk_s_c0_flexgen CLK_MMC_0>; + vqmmc-supply = <&vmmc_reg>; + max-frequency = <200000000>; + bus-width = <8>; + non-removable; + sd-uhs-sdr50; + sd-uhs-sdr104; + sd-uhs-ddr50; }; |
