diff options
Diffstat (limited to 'Documentation/admin-guide/kernel-parameters.txt')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 53 |
1 files changed, 33 insertions, 20 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 122f2d2f3e96..5a92d89a1bd4 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -437,8 +437,6 @@ no delay (0). Format: integer - bootmem_debug [KNL] Enable bootmem allocator debug messages. - bert_disable [ACPI] Disable BERT OS support on buggy BIOSes. @@ -983,12 +981,10 @@ earlycon= [KNL] Output early console device and options. - [ARM64] The early console is determined by the - stdout-path property in device tree's chosen node, - or determined by the ACPI SPCR table. - - [X86] When used with no options the early console is - determined by the ACPI SPCR table. + When used with no options, the early console is + determined by stdout-path property in device tree's + chosen node or the ACPI SPCR table if supported by + the platform. cdns,<addr>[,options] Start an early, polled-mode console on a Cadence @@ -1101,7 +1097,7 @@ mapped with the correct attributes. linflex,<addr> - Use early console provided by Freescale LinFlex UART + Use early console provided by Freescale LINFlexD UART serial driver for NXP S32V234 SoCs. A valid base address must be provided, and the serial port must already be setup and configured. @@ -3240,6 +3236,12 @@ This can be set from sysctl after boot. See Documentation/admin-guide/sysctl/vm.rst for details. + of_devlink [OF, KNL] Create device links between consumer and + supplier devices by scanning the devictree to infer the + consumer/supplier relationships. A consumer device + will not be probed until all the supplier devices have + probed successfully. + ohci1394_dma=early [HW] enable debugging via the ohci1394 driver. See Documentation/debugging-via-ohci1394.txt for more info. @@ -3538,8 +3540,15 @@ hpiosize=nn[KMG] The fixed amount of bus space which is reserved for hotplug bridge's IO window. Default size is 256 bytes. + hpmmiosize=nn[KMG] The fixed amount of bus space which is + reserved for hotplug bridge's MMIO window. + Default size is 2 megabytes. + hpmmioprefsize=nn[KMG] The fixed amount of bus space which is + reserved for hotplug bridge's MMIO_PREF window. + Default size is 2 megabytes. hpmemsize=nn[KMG] The fixed amount of bus space which is - reserved for hotplug bridge's memory window. + reserved for hotplug bridge's MMIO and + MMIO_PREF window. Default size is 2 megabytes. hpbussize=nn The minimum amount of additional bus numbers reserved for buses below a hotplug bridge. @@ -3586,6 +3595,8 @@ even if the platform doesn't give the OS permission to use them. This may cause conflicts if the platform also tries to use these services. + dpc-native Use native PCIe service for DPC only. May + cause conflicts if firmware uses AER or DPC. compat Disable native PCIe services (PME, AER, DPC, PCIe hotplug). @@ -5114,13 +5125,13 @@ Flags is a set of characters, each corresponding to a common usb-storage quirk flag as follows: a = SANE_SENSE (collect more than 18 bytes - of sense data); + of sense data, not on uas); b = BAD_SENSE (don't collect more than 18 - bytes of sense data); + bytes of sense data, not on uas); c = FIX_CAPACITY (decrease the reported device capacity by one sector); d = NO_READ_DISC_INFO (don't use - READ_DISC_INFO command); + READ_DISC_INFO command, not on uas); e = NO_READ_CAPACITY_16 (don't use READ_CAPACITY_16 command); f = NO_REPORT_OPCODES (don't use report opcodes @@ -5135,17 +5146,18 @@ j = NO_REPORT_LUNS (don't use report luns command, uas only); l = NOT_LOCKABLE (don't try to lock and - unlock ejectable media); + unlock ejectable media, not on uas); m = MAX_SECTORS_64 (don't transfer more - than 64 sectors = 32 KB at a time); + than 64 sectors = 32 KB at a time, + not on uas); n = INITIAL_READ10 (force a retry of the - initial READ(10) command); + initial READ(10) command, not on uas); o = CAPACITY_OK (accept the capacity - reported by the device); + reported by the device, not on uas); p = WRITE_CACHE (the device cache is ON - by default); + by default, not on uas); r = IGNORE_RESIDUE (the device reports - bogus residue values); + bogus residue values, not on uas); s = SINGLE_LUN (the device has only one Logical Unit); t = NO_ATA_1X (don't allow ATA(12) and ATA(16) @@ -5154,7 +5166,8 @@ w = NO_WP_DETECT (don't test whether the medium is write-protected). y = ALWAYS_SYNC (issue a SYNCHRONIZE_CACHE - even if the device claims no cache) + even if the device claims no cache, + not on uas) Example: quirks=0419:aaf5:rl,0421:0433:rc user_debug= [KNL,ARM] |
