diff options
Diffstat (limited to 'Documentation/admin-guide/kernel-parameters.txt')
| -rw-r--r-- | Documentation/admin-guide/kernel-parameters.txt | 44 |
1 files changed, 42 insertions, 2 deletions
diff --git a/Documentation/admin-guide/kernel-parameters.txt b/Documentation/admin-guide/kernel-parameters.txt index 782e9072407b..c7ac2f3ac99f 100644 --- a/Documentation/admin-guide/kernel-parameters.txt +++ b/Documentation/admin-guide/kernel-parameters.txt @@ -809,6 +809,8 @@ enables the feature at boot time. By default, it is disabled and the system will work mostly the same as a kernel built without CONFIG_DEBUG_PAGEALLOC. + Note: to get most of debug_pagealloc error reports, it's + useful to also enable the page_owner functionality. on: enable the feature debugpat [X86] Enable PAT debugging @@ -860,6 +862,10 @@ disable_radix [PPC] Disable RADIX MMU mode on POWER9 + disable_tlbie [PPC] + Disable TLBIE instruction. Currently does not work + with KVM, with HASH MMU, or with coherent accelerators. + disable_cpu_apicid= [X86,APIC,SMP] Format: <int> The number of initial APIC ID for the @@ -2270,6 +2276,15 @@ lockd.nlm_udpport=M [NFS] Assign UDP port. Format: <integer> + lockdown= [SECURITY] + { integrity | confidentiality } + Enable the kernel lockdown feature. If set to + integrity, kernel features that allow userland to + modify the running kernel are disabled. If set to + confidentiality, kernel features that allow userland + to extract confidential information from the kernel + are also disabled. + locktorture.nreaders_stress= [KNL] Set the number of locking read-acquisition kthreads. Defaults to being automatically set based on the @@ -3461,12 +3476,13 @@ specify the device is described above. If <order of align> is not specified, PAGE_SIZE is used as alignment. - PCI-PCI bridge can be specified, if resource + A PCI-PCI bridge can be specified if resource windows need to be expanded. To specify the alignment for several instances of a device, the PCI vendor, device, subvendor, and subdevice may be - specified, e.g., 4096@pci:8086:9c22:103c:198f + specified, e.g., 12@pci:8086:9c22:103c:198f + for 4096-byte alignment. ecrc= Enable/disable PCIe ECRC (transaction layer end-to-end CRC checking). bios: Use BIOS/firmware settings. This is the @@ -4641,6 +4657,11 @@ /sys/power/pm_test). Only available when CONFIG_PM_DEBUG is set. Default value is 5. + svm= [PPC] + Format: { on | off | y | n | 1 | 0 } + This parameter controls use of the Protected + Execution Facility on pSeries. + swapaccount=[0|1] [KNL] Enable accounting of swap in memory resource controller if no parameter or 1 is given or disable @@ -5326,3 +5347,22 @@ A hex value specifying bitmask with supplemental xhci host controller quirks. Meaning of each bit can be consulted in header drivers/usb/host/xhci.h. + + xmon [PPC] + Format: { early | on | rw | ro | off } + Controls if xmon debugger is enabled. Default is off. + Passing only "xmon" is equivalent to "xmon=early". + early Call xmon as early as possible on boot; xmon + debugger is called from setup_arch(). + on xmon debugger hooks will be installed so xmon + is only called on a kernel crash. Default mode, + i.e. either "ro" or "rw" mode, is controlled + with CONFIG_XMON_DEFAULT_RO_MODE. + rw xmon debugger hooks will be installed so xmon + is called only on a kernel crash, mode is write, + meaning SPR registers, memory and, other data + can be written using xmon commands. + ro same as "rw" option above but SPR registers, + memory, and other data can't be written using + xmon commands. + off xmon is disabled. |
