Merge branch 'origin' into for-linus

Conflicts:
	MAINTAINERS

1 files changed, 34 insertions, 406 deletions

diff --git a/drivers/usb/host/r8a66597.h b/drivers/usb/host/r8a66597.h
index d72680b433f9..228e3fb23854 100644
--- a/drivers/usb/host/r8a66597.h
+++ b/drivers/usb/host/r8a66597.h
@@ -26,390 +26,16 @@
 #ifndef __R8A66597_H__
 #define __R8A66597_H__
 
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) && defined(CONFIG_HAVE_CLK)
+#ifdef CONFIG_HAVE_CLK
 #include <linux/clk.h>
 #endif
 
 #include <linux/usb/r8a66597.h>
 
-#define SYSCFG0		0x00
-#define SYSCFG1		0x02
-#define SYSSTS0		0x04
-#define SYSSTS1		0x06
-#define DVSTCTR0	0x08
-#define DVSTCTR1	0x0A
-#define TESTMODE	0x0C
-#define PINCFG		0x0E
-#define DMA0CFG		0x10
-#define DMA1CFG		0x12
-#define CFIFO		0x14
-#define D0FIFO		0x18
-#define D1FIFO		0x1C
-#define CFIFOSEL	0x20
-#define CFIFOCTR	0x22
-#define CFIFOSIE	0x24
-#define D0FIFOSEL	0x28
-#define D0FIFOCTR	0x2A
-#define D1FIFOSEL	0x2C
-#define D1FIFOCTR	0x2E
-#define INTENB0		0x30
-#define INTENB1		0x32
-#define INTENB2		0x34
-#define BRDYENB		0x36
-#define NRDYENB		0x38
-#define BEMPENB		0x3A
-#define SOFCFG		0x3C
-#define INTSTS0		0x40
-#define INTSTS1		0x42
-#define INTSTS2		0x44
-#define BRDYSTS		0x46
-#define NRDYSTS		0x48
-#define BEMPSTS		0x4A
-#define FRMNUM		0x4C
-#define UFRMNUM		0x4E
-#define USBADDR		0x50
-#define USBREQ		0x54
-#define USBVAL		0x56
-#define USBINDX		0x58
-#define USBLENG		0x5A
-#define DCPCFG		0x5C
-#define DCPMAXP		0x5E
-#define DCPCTR		0x60
-#define PIPESEL		0x64
-#define PIPECFG		0x68
-#define PIPEBUF		0x6A
-#define PIPEMAXP	0x6C
-#define PIPEPERI	0x6E
-#define PIPE1CTR	0x70
-#define PIPE2CTR	0x72
-#define PIPE3CTR	0x74
-#define PIPE4CTR	0x76
-#define PIPE5CTR	0x78
-#define PIPE6CTR	0x7A
-#define PIPE7CTR	0x7C
-#define PIPE8CTR	0x7E
-#define PIPE9CTR	0x80
-#define PIPE1TRE	0x90
-#define PIPE1TRN	0x92
-#define PIPE2TRE	0x94
-#define PIPE2TRN	0x96
-#define PIPE3TRE	0x98
-#define PIPE3TRN	0x9A
-#define PIPE4TRE	0x9C
-#define	PIPE4TRN	0x9E
-#define	PIPE5TRE	0xA0
-#define	PIPE5TRN	0xA2
-#define DEVADD0		0xD0
-#define DEVADD1		0xD2
-#define DEVADD2		0xD4
-#define DEVADD3		0xD6
-#define DEVADD4		0xD8
-#define DEVADD5		0xDA
-#define DEVADD6		0xDC
-#define DEVADD7		0xDE
-#define DEVADD8		0xE0
-#define DEVADD9		0xE2
-#define DEVADDA		0xE4
-
-/* System Configuration Control Register */
-#define	XTAL		0xC000	/* b15-14: Crystal selection */
-#define	  XTAL48	 0x8000	  /* 48MHz */
-#define	  XTAL24	 0x4000	  /* 24MHz */
-#define	  XTAL12	 0x0000	  /* 12MHz */
-#define	XCKE		0x2000	/* b13: External clock enable */
-#define	PLLC		0x0800	/* b11: PLL control */
-#define	SCKE		0x0400	/* b10: USB clock enable */
-#define	PCSDIS		0x0200	/* b9: not CS wakeup */
-#define	LPSME		0x0100	/* b8: Low power sleep mode */
-#define	HSE		0x0080	/* b7: Hi-speed enable */
-#define	DCFM		0x0040	/* b6: Controller function select  */
-#define	DRPD		0x0020	/* b5: D+/- pull down control */
-#define	DPRPU		0x0010	/* b4: D+ pull up control */
-#define	USBE		0x0001	/* b0: USB module operation enable */
-
-/* System Configuration Status Register */
-#define	OVCBIT		0x8000	/* b15-14: Over-current bit */
-#define	OVCMON		0xC000	/* b15-14: Over-current monitor */
-#define	SOFEA		0x0020	/* b5: SOF monitor */
-#define	IDMON		0x0004	/* b3: ID-pin monitor */
-#define	LNST		0x0003	/* b1-0: D+, D- line status */
-#define	  SE1		 0x0003	  /* SE1 */
-#define	  FS_KSTS	 0x0002	  /* Full-Speed K State */
-#define	  FS_JSTS	 0x0001	  /* Full-Speed J State */
-#define	  LS_JSTS	 0x0002	  /* Low-Speed J State */
-#define	  LS_KSTS	 0x0001	  /* Low-Speed K State */
-#define	  SE0		 0x0000	  /* SE0 */
-
-/* Device State Control Register */
-#define	EXTLP0		0x0400	/* b10: External port */
-#define	VBOUT		0x0200	/* b9: VBUS output */
-#define	WKUP		0x0100	/* b8: Remote wakeup */
-#define	RWUPE		0x0080	/* b7: Remote wakeup sense */
-#define	USBRST		0x0040	/* b6: USB reset enable */
-#define	RESUME		0x0020	/* b5: Resume enable */
-#define	UACT		0x0010	/* b4: USB bus enable */
-#define	RHST		0x0007	/* b1-0: Reset handshake status */
-#define	  HSPROC	 0x0004	  /* HS handshake is processing */
-#define	  HSMODE	 0x0003	  /* Hi-Speed mode */
-#define	  FSMODE	 0x0002	  /* Full-Speed mode */
-#define	  LSMODE	 0x0001	  /* Low-Speed mode */
-#define	  UNDECID	 0x0000	  /* Undecided */
-
-/* Test Mode Register */
-#define	UTST			0x000F	/* b3-0: Test select */
-#define	  H_TST_PACKET		 0x000C	  /* HOST TEST Packet */
-#define	  H_TST_SE0_NAK		 0x000B	  /* HOST TEST SE0 NAK */
-#define	  H_TST_K		 0x000A	  /* HOST TEST K */
-#define	  H_TST_J		 0x0009	  /* HOST TEST J */
-#define	  H_TST_NORMAL		 0x0000	  /* HOST Normal Mode */
-#define	  P_TST_PACKET		 0x0004	  /* PERI TEST Packet */
-#define	  P_TST_SE0_NAK		 0x0003	  /* PERI TEST SE0 NAK */
-#define	  P_TST_K		 0x0002	  /* PERI TEST K */
-#define	  P_TST_J		 0x0001	  /* PERI TEST J */
-#define	  P_TST_NORMAL		 0x0000	  /* PERI Normal Mode */
-
-/* Data Pin Configuration Register */
-#define	LDRV			0x8000	/* b15: Drive Current Adjust */
-#define	  VIF1			  0x0000		/* VIF = 1.8V */
-#define	  VIF3			  0x8000		/* VIF = 3.3V */
-#define	INTA			0x0001	/* b1: USB INT-pin active */
-
-/* DMAx Pin Configuration Register */
-#define	DREQA			0x4000	/* b14: Dreq active select */
-#define	BURST			0x2000	/* b13: Burst mode */
-#define	DACKA			0x0400	/* b10: Dack active select */
-#define	DFORM			0x0380	/* b9-7: DMA mode select */
-#define	  CPU_ADR_RD_WR		 0x0000	  /* Address + RD/WR mode (CPU bus) */
-#define	  CPU_DACK_RD_WR	 0x0100	  /* DACK + RD/WR mode (CPU bus) */
-#define	  CPU_DACK_ONLY		 0x0180	  /* DACK only mode (CPU bus) */
-#define	  SPLIT_DACK_ONLY	 0x0200	  /* DACK only mode (SPLIT bus) */
-#define	DENDA			0x0040	/* b6: Dend active select */
-#define	PKTM			0x0020	/* b5: Packet mode */
-#define	DENDE			0x0010	/* b4: Dend enable */
-#define	OBUS			0x0004	/* b2: OUTbus mode */
-
-/* CFIFO/DxFIFO Port Select Register */
-#define	RCNT		0x8000	/* b15: Read count mode */
-#define	REW		0x4000	/* b14: Buffer rewind */
-#define	DCLRM		0x2000	/* b13: DMA buffer clear mode */
-#define	DREQE		0x1000	/* b12: DREQ output enable */
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597)
-#define	MBW		0x0800
-#else
-#define	MBW		0x0400	/* b10: Maximum bit width for FIFO access */
-#endif
-#define	  MBW_8		 0x0000	  /*  8bit */
-#define	  MBW_16	 0x0400	  /* 16bit */
-#define	BIGEND		0x0100	/* b8: Big endian mode */
-#define	  BYTE_LITTLE	 0x0000		/* little dendian */
-#define	  BYTE_BIG	 0x0100		/* big endifan */
-#define	ISEL		0x0020	/* b5: DCP FIFO port direction select */
-#define	CURPIPE		0x000F	/* b2-0: PIPE select */
-
-/* CFIFO/DxFIFO Port Control Register */
-#define	BVAL		0x8000	/* b15: Buffer valid flag */
-#define	BCLR		0x4000	/* b14: Buffer clear */
-#define	FRDY		0x2000	/* b13: FIFO ready */
-#define	DTLN		0x0FFF	/* b11-0: FIFO received data length */
-
-/* Interrupt Enable Register 0 */
-#define	VBSE	0x8000	/* b15: VBUS interrupt */
-#define	RSME	0x4000	/* b14: Resume interrupt */
-#define	SOFE	0x2000	/* b13: Frame update interrupt */
-#define	DVSE	0x1000	/* b12: Device state transition interrupt */
-#define	CTRE	0x0800	/* b11: Control transfer stage transition interrupt */
-#define	BEMPE	0x0400	/* b10: Buffer empty interrupt */
-#define	NRDYE	0x0200	/* b9: Buffer not ready interrupt */
-#define	BRDYE	0x0100	/* b8: Buffer ready interrupt */
-
-/* Interrupt Enable Register 1 */
-#define	OVRCRE		0x8000	/* b15: Over-current interrupt */
-#define	BCHGE		0x4000	/* b14: USB us chenge interrupt */
-#define	DTCHE		0x1000	/* b12: Detach sense interrupt */
-#define	ATTCHE		0x0800	/* b11: Attach sense interrupt */
-#define	EOFERRE		0x0040	/* b6: EOF error interrupt */
-#define	SIGNE		0x0020	/* b5: SETUP IGNORE interrupt */
-#define	SACKE		0x0010	/* b4: SETUP ACK interrupt */
-
-/* BRDY Interrupt Enable/Status Register */
-#define	BRDY9		0x0200	/* b9: PIPE9 */
-#define	BRDY8		0x0100	/* b8: PIPE8 */
-#define	BRDY7		0x0080	/* b7: PIPE7 */
-#define	BRDY6		0x0040	/* b6: PIPE6 */
-#define	BRDY5		0x0020	/* b5: PIPE5 */
-#define	BRDY4		0x0010	/* b4: PIPE4 */
-#define	BRDY3		0x0008	/* b3: PIPE3 */
-#define	BRDY2		0x0004	/* b2: PIPE2 */
-#define	BRDY1		0x0002	/* b1: PIPE1 */
-#define	BRDY0		0x0001	/* b1: PIPE0 */
-
-/* NRDY Interrupt Enable/Status Register */
-#define	NRDY9		0x0200	/* b9: PIPE9 */
-#define	NRDY8		0x0100	/* b8: PIPE8 */
-#define	NRDY7		0x0080	/* b7: PIPE7 */
-#define	NRDY6		0x0040	/* b6: PIPE6 */
-#define	NRDY5		0x0020	/* b5: PIPE5 */
-#define	NRDY4		0x0010	/* b4: PIPE4 */
-#define	NRDY3		0x0008	/* b3: PIPE3 */
-#define	NRDY2		0x0004	/* b2: PIPE2 */
-#define	NRDY1		0x0002	/* b1: PIPE1 */
-#define	NRDY0		0x0001	/* b1: PIPE0 */
-
-/* BEMP Interrupt Enable/Status Register */
-#define	BEMP9		0x0200	/* b9: PIPE9 */
-#define	BEMP8		0x0100	/* b8: PIPE8 */
-#define	BEMP7		0x0080	/* b7: PIPE7 */
-#define	BEMP6		0x0040	/* b6: PIPE6 */
-#define	BEMP5		0x0020	/* b5: PIPE5 */
-#define	BEMP4		0x0010	/* b4: PIPE4 */
-#define	BEMP3		0x0008	/* b3: PIPE3 */
-#define	BEMP2		0x0004	/* b2: PIPE2 */
-#define	BEMP1		0x0002	/* b1: PIPE1 */
-#define	BEMP0		0x0001	/* b0: PIPE0 */
-
-/* SOF Pin Configuration Register */
-#define	TRNENSEL	0x0100	/* b8: Select transaction enable period */
-#define	BRDYM		0x0040	/* b6: BRDY clear timing */
-#define	INTL		0x0020	/* b5: Interrupt sense select */
-#define	EDGESTS		0x0010	/* b4:  */
-#define	SOFMODE		0x000C	/* b3-2: SOF pin select */
-#define	  SOF_125US	 0x0008	  /* SOF OUT 125us Frame Signal */
-#define	  SOF_1MS	 0x0004	  /* SOF OUT 1ms Frame Signal */
-#define	  SOF_DISABLE	 0x0000	  /* SOF OUT Disable */
-
-/* Interrupt Status Register 0 */
-#define	VBINT	0x8000	/* b15: VBUS interrupt */
-#define	RESM	0x4000	/* b14: Resume interrupt */
-#define	SOFR	0x2000	/* b13: SOF frame update interrupt */
-#define	DVST	0x1000	/* b12: Device state transition interrupt */
-#define	CTRT	0x0800	/* b11: Control transfer stage transition interrupt */
-#define	BEMP	0x0400	/* b10: Buffer empty interrupt */
-#define	NRDY	0x0200	/* b9: Buffer not ready interrupt */
-#define	BRDY	0x0100	/* b8: Buffer ready interrupt */
-#define	VBSTS	0x0080	/* b7: VBUS input port */
-#define	DVSQ	0x0070	/* b6-4: Device state */
-#define	  DS_SPD_CNFG	 0x0070	  /* Suspend Configured */
-#define	  DS_SPD_ADDR	 0x0060	  /* Suspend Address */
-#define	  DS_SPD_DFLT	 0x0050	  /* Suspend Default */
-#define	  DS_SPD_POWR	 0x0040	  /* Suspend Powered */
-#define	  DS_SUSP	 0x0040	  /* Suspend */
-#define	  DS_CNFG	 0x0030	  /* Configured */
-#define	  DS_ADDS	 0x0020	  /* Address */
-#define	  DS_DFLT	 0x0010	  /* Default */
-#define	  DS_POWR	 0x0000	  /* Powered */
-#define	DVSQS		0x0030	/* b5-4: Device state */
-#define	VALID		0x0008	/* b3: Setup packet detected flag */
-#define	CTSQ		0x0007	/* b2-0: Control transfer stage */
-#define	  CS_SQER	 0x0006	  /* Sequence error */
-#define	  CS_WRND	 0x0005	  /* Control write nodata status stage */
-#define	  CS_WRSS	 0x0004	  /* Control write status stage */
-#define	  CS_WRDS	 0x0003	  /* Control write data stage */
-#define	  CS_RDSS	 0x0002	  /* Control read status stage */
-#define	  CS_RDDS	 0x0001	  /* Control read data stage */
-#define	  CS_IDST	 0x0000	  /* Idle or setup stage */
-
-/* Interrupt Status Register 1 */
-#define	OVRCR		0x8000	/* b15: Over-current interrupt */
-#define	BCHG		0x4000	/* b14: USB bus chenge interrupt */
-#define	DTCH		0x1000	/* b12: Detach sense interrupt */
-#define	ATTCH		0x0800	/* b11: Attach sense interrupt */
-#define	EOFERR		0x0040	/* b6: EOF-error interrupt */
-#define	SIGN		0x0020	/* b5: Setup ignore interrupt */
-#define	SACK		0x0010	/* b4: Setup acknowledge interrupt */
-
-/* Frame Number Register */
-#define	OVRN		0x8000	/* b15: Overrun error */
-#define	CRCE		0x4000	/* b14: Received data error */
-#define	FRNM		0x07FF	/* b10-0: Frame number */
-
-/* Micro Frame Number Register */
-#define	UFRNM		0x0007	/* b2-0: Micro frame number */
-
-/* Default Control Pipe Maxpacket Size Register */
-/* Pipe Maxpacket Size Register */
-#define	DEVSEL	0xF000	/* b15-14: Device address select */
-#define	MAXP	0x007F	/* b6-0: Maxpacket size of default control pipe */
-
-/* Default Control Pipe Control Register */
-#define	BSTS		0x8000	/* b15: Buffer status */
-#define	SUREQ		0x4000	/* b14: Send USB request  */
-#define	CSCLR		0x2000	/* b13: complete-split status clear */
-#define	CSSTS		0x1000	/* b12: complete-split status */
-#define	SUREQCLR	0x0800	/* b11: stop setup request */
-#define	SQCLR		0x0100	/* b8: Sequence toggle bit clear */
-#define	SQSET		0x0080	/* b7: Sequence toggle bit set */
-#define	SQMON		0x0040	/* b6: Sequence toggle bit monitor */
-#define	PBUSY		0x0020	/* b5: pipe busy */
-#define	PINGE		0x0010	/* b4: ping enable */
-#define	CCPL		0x0004	/* b2: Enable control transfer complete */
-#define	PID		0x0003	/* b1-0: Response PID */
-#define	  PID_STALL11	 0x0003	  /* STALL */
-#define	  PID_STALL	 0x0002	  /* STALL */
-#define	  PID_BUF	 0x0001	  /* BUF */
-#define	  PID_NAK	 0x0000	  /* NAK */
-
-/* Pipe Window Select Register */
-#define	PIPENM		0x0007	/* b2-0: Pipe select */
-
-/* Pipe Configuration Register */
-#define	R8A66597_TYP	0xC000	/* b15-14: Transfer type */
-#define	  R8A66597_ISO	 0xC000		  /* Isochronous */
-#define	  R8A66597_INT	 0x8000		  /* Interrupt */
-#define	  R8A66597_BULK	 0x4000		  /* Bulk */
-#define	R8A66597_BFRE	0x0400	/* b10: Buffer ready interrupt mode select */
-#define	R8A66597_DBLB	0x0200	/* b9: Double buffer mode select */
-#define	R8A66597_CNTMD	0x0100	/* b8: Continuous transfer mode select */
-#define	R8A66597_SHTNAK	0x0080	/* b7: Transfer end NAK */
-#define	R8A66597_DIR	0x0010	/* b4: Transfer direction select */
-#define	R8A66597_EPNUM	0x000F	/* b3-0: Eendpoint number select */
-
-/* Pipe Buffer Configuration Register */
-#define	BUFSIZE		0x7C00	/* b14-10: Pipe buffer size */
-#define	BUFNMB		0x007F	/* b6-0: Pipe buffer number */
-#define	PIPE0BUF	256
-#define	PIPExBUF	64
-
-/* Pipe Maxpacket Size Register */
-#define	MXPS		0x07FF	/* b10-0: Maxpacket size */
-
-/* Pipe Cycle Configuration Register */
-#define	IFIS	0x1000	/* b12: Isochronous in-buffer flush mode select */
-#define	IITV	0x0007	/* b2-0: Isochronous interval */
-
-/* Pipex Control Register */
-#define	BSTS	0x8000	/* b15: Buffer status */
-#define	INBUFM	0x4000	/* b14: IN buffer monitor (Only for PIPE1 to 5) */
-#define	CSCLR	0x2000	/* b13: complete-split status clear */
-#define	CSSTS	0x1000	/* b12: complete-split status */
-#define	ATREPM	0x0400	/* b10: Auto repeat mode */
-#define	ACLRM	0x0200	/* b9: Out buffer auto clear mode */
-#define	SQCLR	0x0100	/* b8: Sequence toggle bit clear */
-#define	SQSET	0x0080	/* b7: Sequence toggle bit set */
-#define	SQMON	0x0040	/* b6: Sequence toggle bit monitor */
-#define	PBUSY	0x0020	/* b5: pipe busy */
-#define	PID	0x0003	/* b1-0: Response PID */
-
-/* PIPExTRE */
-#define	TRENB		0x0200	/* b9: Transaction counter enable */
-#define	TRCLR		0x0100	/* b8: Transaction counter clear */
-
-/* PIPExTRN */
-#define	TRNCNT		0xFFFF	/* b15-0: Transaction counter */
-
-/* DEVADDx */
-#define	UPPHUB		0x7800
-#define	HUBPORT		0x0700
-#define	USBSPD		0x00C0
-#define	RTPORT		0x0001
-
 #define R8A66597_MAX_NUM_PIPE		10
 #define R8A66597_BUF_BSIZE		8
 #define R8A66597_MAX_DEVICE		10
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597)
-#define R8A66597_MAX_ROOT_HUB		1
-#else
 #define R8A66597_MAX_ROOT_HUB		2
-#endif
 #define R8A66597_MAX_SAMPLING		5
 #define R8A66597_RH_POLL_TIME		10
 #define R8A66597_MAX_DMA_CHANNEL	2
@@ -487,7 +113,7 @@ struct r8a66597_root_hub {
 struct r8a66597 {
 	spinlock_t lock;
 	unsigned long reg;
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597) && defined(CONFIG_HAVE_CLK)
+#ifdef CONFIG_HAVE_CLK
 	struct clk *clk;
 #endif
 	struct r8a66597_platdata	*pdata;
@@ -504,6 +130,7 @@ struct r8a66597 {
 	unsigned short interval_map;
 	unsigned char pipe_cnt[R8A66597_MAX_NUM_PIPE];
 	unsigned char dma_map;
+	unsigned int max_root_hub;
 
 	struct list_head child_device;
 	unsigned long child_connect_map[4];
@@ -550,21 +177,22 @@ static inline void r8a66597_read_fifo(struct r8a66597 *r8a66597,
 				      unsigned long offset, u16 *buf,
 				      int len)
 {
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597)
 	unsigned long fifoaddr = r8a66597->reg + offset;
 	unsigned long count;
 
-	count = len / 4;
-	insl(fifoaddr, buf, count);
+	if (r8a66597->pdata->on_chip) {
+		count = len / 4;
+		insl(fifoaddr, buf, count);
 
-	if (len & 0x00000003) {
-		unsigned long tmp = inl(fifoaddr);
-		memcpy((unsigned char *)buf + count * 4, &tmp, len & 0x03);
+		if (len & 0x00000003) {
+			unsigned long tmp = inl(fifoaddr);
+			memcpy((unsigned char *)buf + count * 4, &tmp,
+			       len & 0x03);
+		}
+	} else {
+		len = (len + 1) / 2;
+		insw(fifoaddr, buf, len);
 	}
-#else
-	len = (len + 1) / 2;
-	insw(r8a66597->reg + offset, buf, len);
-#endif
 }
 
 static inline void r8a66597_write(struct r8a66597 *r8a66597, u16 val,
@@ -578,33 +206,33 @@ static inline void r8a66597_write_fifo(struct r8a66597 *r8a66597,
 				       int len)
 {
 	unsigned long fifoaddr = r8a66597->reg + offset;
-#if defined(CONFIG_SUPERH_ON_CHIP_R8A66597)
 	unsigned long count;
 	unsigned char *pb;
 	int i;
 
-	count = len / 4;
-	outsl(fifoaddr, buf, count);
+	if (r8a66597->pdata->on_chip) {
+		count = len / 4;
+		outsl(fifoaddr, buf, count);
+
+		if (len & 0x00000003) {
+			pb = (unsigned char *)buf + count * 4;
+			for (i = 0; i < (len & 0x00000003); i++) {
+				if (r8a66597_read(r8a66597, CFIFOSEL) & BIGEND)
+					outb(pb[i], fifoaddr + i);
+				else
+					outb(pb[i], fifoaddr + 3 - i);
+			}
+		}
+	} else {
+		int odd = len & 0x0001;
 
-	if (len & 0x00000003) {
-		pb = (unsigned char *)buf + count * 4;
-		for (i = 0; i < (len & 0x00000003); i++) {
-			if (r8a66597_read(r8a66597, CFIFOSEL) & BIGEND)
-				outb(pb[i], fifoaddr + i);
-			else
-				outb(pb[i], fifoaddr + 3 - i);
+		len = len / 2;
+		outsw(fifoaddr, buf, len);
+		if (unlikely(odd)) {
+			buf = &buf[len];
+			outb((unsigned char)*buf, fifoaddr);
 		}
 	}
-#else
-	int odd = len & 0x0001;
-
-	len = len / 2;
-	outsw(fifoaddr, buf, len);
-	if (unlikely(odd)) {
-		buf = &buf[len];
-		outb((unsigned char)*buf, fifoaddr);
-	}
-#endif
 }
 
 static inline void r8a66597_mdfy(struct r8a66597 *r8a66597,