ufs: refactor configuring power mode

Sometimes, the device shall report its maximum power and speed
capabilities, but we might not wish to configure it to use those
maximum capabilities.
This change adds support for the vendor specific host driver to
implement power change notify callback.

To enable configuring different power modes (number of lanes,
gear number and fast/slow modes) it is necessary to split the
configuration stage from the stage that reads the device max power mode.
In addition, it is not required to read the configuration more than
once, thus the configuration is stored after reading it once.

Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>

1 files changed, 27 insertions, 0 deletions

diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h
index e1bde0598d92..343b18a7a8b0 100644
--- a/drivers/scsi/ufs/ufshcd.h
+++ b/drivers/scsi/ufs/ufshcd.h
@@ -221,6 +221,22 @@ struct ufs_clk_info {
 
 #define PRE_CHANGE      0
 #define POST_CHANGE     1
+
+struct ufs_pa_layer_attr {
+	u32 gear_rx;
+	u32 gear_tx;
+	u32 lane_rx;
+	u32 lane_tx;
+	u32 pwr_rx;
+	u32 pwr_tx;
+	u32 hs_rate;
+};
+
+struct ufs_pwr_mode_info {
+	bool is_valid;
+	struct ufs_pa_layer_attr info;
+};
+
 /**
  * struct ufs_hba_variant_ops - variant specific callbacks
  * @name: variant name
@@ -232,6 +248,9 @@ struct ufs_clk_info {
  *                     variant specific Uni-Pro initialization.
  * @link_startup_notify: called before and after Link startup is carried out
  *                       to allow variant specific Uni-Pro initialization.
+ * @pwr_change_notify: called before and after a power mode change
+ *			is carried out to allow vendor spesific capabilities
+ *			to be set.
  * @suspend: called during host controller PM callback
  * @resume: called during host controller PM callback
  */
@@ -243,6 +262,9 @@ struct ufs_hba_variant_ops {
 	int     (*setup_regulators)(struct ufs_hba *, bool);
 	int     (*hce_enable_notify)(struct ufs_hba *, bool);
 	int     (*link_startup_notify)(struct ufs_hba *, bool);
+	int	(*pwr_change_notify)(struct ufs_hba *,
+					bool, struct ufs_pa_layer_attr *,
+					struct ufs_pa_layer_attr *);
 	int     (*suspend)(struct ufs_hba *, enum ufs_pm_op);
 	int     (*resume)(struct ufs_hba *, enum ufs_pm_op);
 };
@@ -302,6 +324,8 @@ struct ufs_init_prefetch {
  * @auto_bkops_enabled: to track whether bkops is enabled in device
  * @vreg_info: UFS device voltage regulator information
  * @clk_list_head: UFS host controller clocks list node head
+ * @pwr_info: holds current power mode
+ * @max_pwr_info: keeps the device max valid pwm
  */
 struct ufs_hba {
 	void __iomem *mmio_base;
@@ -387,6 +411,9 @@ struct ufs_hba {
 	struct list_head clk_list_head;
 
 	bool wlun_dev_clr_ua;
+
+	struct ufs_pa_layer_attr pwr_info;
+	struct ufs_pwr_mode_info max_pwr_info;
 };
 
 #define ufshcd_writel(hba, val, reg)	\