Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next

Pull networking merge from David Miller:
 "1) Move ixgbe driver over to purely page based buffering on receive.
     From Alexander Duyck.

  2) Add receive packet steering support to e1000e, from Bruce Allan.

  3) Convert TCP MD5 support over to RCU, from Eric Dumazet.

  4) Reduce cpu usage in handling out-of-order TCP packets on modern
     systems, also from Eric Dumazet.

  5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
     folks happy, from Erich Hoover.

  6) Support VLAN trunking from guests in hyperv driver, from Haiyang
     Zhang.

  7) Support byte-queue-limtis in r8169, from Igor Maravic.

  8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
     was never properly implemented, Jiri Benc fixed that.

  9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.

  10) Support kernel side dump filtering by ctmark in netfilter
      ctnetlink, from Pablo Neira Ayuso.

  11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.

  12) Add new peek socket options to assist with socket migration, from
      Pavel Emelyanov.

  13) Add sch_plug packet scheduler whose queue is controlled by
      userland daemons using explicit freeze and release commands.  From
      Shriram Rajagopalan.

  14) Fix FCOE checksum offload handling on transmit, from Yi Zou."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
  Fix pppol2tp getsockname()
  Remove printk from rds_sendmsg
  ipv6: fix incorrent ipv6 ipsec packet fragment
  cpsw: Hook up default ndo_change_mtu.
  net: qmi_wwan: fix build error due to cdc-wdm dependecy
  netdev: driver: ethernet: Add TI CPSW driver
  netdev: driver: ethernet: add cpsw address lookup engine support
  phy: add am79c874 PHY support
  mlx4_core: fix race on comm channel
  bonding: send igmp report for its master
  fs_enet: Add MPC5125 FEC support and PHY interface selection
  net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
  net: update the usage of CHECKSUM_UNNECESSARY
  fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
  net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
  ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
  net/hyperv: Fix the code handling tx busy
  ixgbe: fix namespace issues when FCoE/DCB is not enabled
  rtlwifi: Remove unused ETH_ADDR_LEN defines
  igbvf: Use ETH_ALEN
  ...

Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.

6 files changed, 1300 insertions, 28 deletions

diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig
index 36e9d594069d..b60d6c5f29a0 100644
--- a/drivers/net/can/sja1000/Kconfig
+++ b/drivers/net/can/sja1000/Kconfig
@@ -43,12 +43,33 @@ config CAN_EMS_PCI
 	  CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche
 	  (http://www.ems-wuensche.de).
 
+config CAN_PEAK_PCMCIA
+	tristate "PEAK PCAN-PC Card"
+	depends on PCMCIA
+	---help---
+	  This driver is for the PCAN-PC Card PCMCIA adapter (1 or 2 channels)
+	  from PEAK-System (http://www.peak-system.com). To compile this
+	  driver as a module, choose M here: the module will be called
+	  peak_pcmcia.
+
 config CAN_PEAK_PCI
-	tristate "PEAK PCAN PCI/PCIe Cards"
+	tristate "PEAK PCAN-PCI/PCIe/miniPCI Cards"
 	depends on PCI
 	---help---
-	  This driver is for the PCAN PCI/PCIe cards (1, 2, 3 or 4 channels)
-	  from PEAK Systems (http://www.peak-system.com).
+	  This driver is for the PCAN-PCI/PCIe/miniPCI cards
+	  (1, 2, 3 or 4 channels) from PEAK-System Technik
+	  (http://www.peak-system.com).
+
+config CAN_PEAK_PCIEC
+	bool "PEAK PCAN-ExpressCard Cards"
+	depends on CAN_PEAK_PCI
+	select I2C
+	select I2C_ALGOBIT
+	default y
+	---help---
+	  Say Y here if you want to use a PCAN-ExpressCard from PEAK-System
+	  Technik. This will also automatically select I2C and I2C_ALGO
+	  configuration options.
 
 config CAN_KVASER_PCI
 	tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards"
@@ -71,6 +92,7 @@ config CAN_PLX_PCI
 	   - esd CAN-PCIe/2000
 	   - Marathon CAN-bus-PCI card (http://www.marathon.ru/)
 	   - TEWS TECHNOLOGIES TPMC810 card (http://www.tews.com/)
+	   - IXXAT Automation PC-I 04/PCI card (http://www.ixxat.com/)
 
 config CAN_TSCAN1
 	tristate "TS-CAN1 PC104 boards"
diff --git a/drivers/net/can/sja1000/Makefile b/drivers/net/can/sja1000/Makefile
index 0604f240c8b1..b3d05cbfec36 100644
--- a/drivers/net/can/sja1000/Makefile
+++ b/drivers/net/can/sja1000/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_CAN_SJA1000_OF_PLATFORM) += sja1000_of_platform.o
 obj-$(CONFIG_CAN_EMS_PCMCIA) += ems_pcmcia.o
 obj-$(CONFIG_CAN_EMS_PCI) += ems_pci.o
 obj-$(CONFIG_CAN_KVASER_PCI) += kvaser_pci.o
+obj-$(CONFIG_CAN_PEAK_PCMCIA) += peak_pcmcia.o
 obj-$(CONFIG_CAN_PEAK_PCI) += peak_pci.o
 obj-$(CONFIG_CAN_PLX_PCI) += plx_pci.o
 obj-$(CONFIG_CAN_TSCAN1) += tscan1.o
diff --git a/drivers/net/can/sja1000/peak_pci.c b/drivers/net/can/sja1000/peak_pci.c
index 214795945bc4..5f92b865f64b 100644
--- a/drivers/net/can/sja1000/peak_pci.c
+++ b/drivers/net/can/sja1000/peak_pci.c
@@ -1,5 +1,6 @@
 /*
  * Copyright (C) 2007, 2011 Wolfgang Grandegger <wg@grandegger.com>
+ * Copyright (C) 2012 Stephane Grosjean <s.grosjean@peak-system.com>
  *
  * Derived from the PCAN project file driver/src/pcan_pci.c:
  *
@@ -13,10 +14,6 @@
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
  * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software Foundation,
- * Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA.
  */
 
 #include <linux/kernel.h>
@@ -26,22 +23,26 @@
 #include <linux/delay.h>
 #include <linux/pci.h>
 #include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/i2c-algo-bit.h>
 #include <linux/can.h>
 #include <linux/can/dev.h>
 
 #include "sja1000.h"
 
 MODULE_AUTHOR("Wolfgang Grandegger <wg@grandegger.com>");
-MODULE_DESCRIPTION("Socket-CAN driver for PEAK PCAN PCI/PCIe cards");
-MODULE_SUPPORTED_DEVICE("PEAK PCAN PCI/PCIe CAN card");
+MODULE_DESCRIPTION("Socket-CAN driver for PEAK PCAN PCI family cards");
+MODULE_SUPPORTED_DEVICE("PEAK PCAN PCI/PCIe/PCIeC miniPCI CAN cards");
 MODULE_LICENSE("GPL v2");
 
 #define DRV_NAME  "peak_pci"
 
+struct peak_pciec_card;
 struct peak_pci_chan {
 	void __iomem *cfg_base;		/* Common for all channels */
 	struct net_device *prev_dev;	/* Chain of network devices */
 	u16 icr_mask;			/* Interrupt mask for fast ack */
+	struct peak_pciec_card *pciec_card;	/* only for PCIeC LEDs */
 };
 
 #define PEAK_PCI_CAN_CLOCK	(16000000 / 2)
@@ -61,16 +62,464 @@ struct peak_pci_chan {
 
 #define PEAK_PCI_VENDOR_ID	0x001C	/* The PCI device and vendor IDs */
 #define PEAK_PCI_DEVICE_ID	0x0001	/* for PCI/PCIe slot cards */
+#define PEAK_PCIEC_DEVICE_ID	0x0002	/* for ExpressCard slot cards */
+#define PEAK_PCIE_DEVICE_ID	0x0003	/* for nextgen PCIe slot cards */
+#define PEAK_MPCI_DEVICE_ID	0x0008	/* The miniPCI slot cards */
+
+#define PEAK_PCI_CHAN_MAX	4
 
-static const u16 peak_pci_icr_masks[] = {0x02, 0x01, 0x40, 0x80};
+static const u16 peak_pci_icr_masks[PEAK_PCI_CHAN_MAX] = {
+	0x02, 0x01, 0x40, 0x80
+};
 
 static DEFINE_PCI_DEVICE_TABLE(peak_pci_tbl) = {
 	{PEAK_PCI_VENDOR_ID, PEAK_PCI_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+	{PEAK_PCI_VENDOR_ID, PEAK_PCIE_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+	{PEAK_PCI_VENDOR_ID, PEAK_MPCI_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+#ifdef CONFIG_CAN_PEAK_PCIEC
+	{PEAK_PCI_VENDOR_ID, PEAK_PCIEC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
+#endif
 	{0,}
 };
 
 MODULE_DEVICE_TABLE(pci, peak_pci_tbl);
 
+#ifdef CONFIG_CAN_PEAK_PCIEC
+/*
+ * PCAN-ExpressCard needs I2C bit-banging configuration option.
+ */
+
+/* GPIOICR byte access offsets */
+#define PITA_GPOUT		0x18	/* GPx output value */
+#define PITA_GPIN		0x19	/* GPx input value */
+#define PITA_GPOEN		0x1A	/* configure GPx as ouput pin */
+
+/* I2C GP bits */
+#define PITA_GPIN_SCL		0x01	/* Serial Clock Line */
+#define PITA_GPIN_SDA		0x04	/* Serial DAta line */
+
+#define PCA9553_1_SLAVEADDR	(0xC4 >> 1)
+
+/* PCA9553 LS0 fields values */
+enum {
+	PCA9553_LOW,
+	PCA9553_HIGHZ,
+	PCA9553_PWM0,
+	PCA9553_PWM1
+};
+
+/* LEDs control */
+#define PCA9553_ON		PCA9553_LOW
+#define PCA9553_OFF		PCA9553_HIGHZ
+#define PCA9553_SLOW		PCA9553_PWM0
+#define PCA9553_FAST		PCA9553_PWM1
+
+#define PCA9553_LED(c)		(1 << (c))
+#define PCA9553_LED_STATE(s, c)	((s) << ((c) << 1))
+
+#define PCA9553_LED_ON(c)	PCA9553_LED_STATE(PCA9553_ON, c)
+#define PCA9553_LED_OFF(c)	PCA9553_LED_STATE(PCA9553_OFF, c)
+#define PCA9553_LED_SLOW(c)	PCA9553_LED_STATE(PCA9553_SLOW, c)
+#define PCA9553_LED_FAST(c)	PCA9553_LED_STATE(PCA9553_FAST, c)
+#define PCA9553_LED_MASK(c)	PCA9553_LED_STATE(0x03, c)
+
+#define PCA9553_LED_OFF_ALL	(PCA9553_LED_OFF(0) | PCA9553_LED_OFF(1))
+
+#define PCA9553_LS0_INIT	0x40 /* initial value (!= from 0x00) */
+
+struct peak_pciec_chan {
+	struct net_device *netdev;
+	unsigned long prev_rx_bytes;
+	unsigned long prev_tx_bytes;
+};
+
+struct peak_pciec_card {
+	void __iomem *cfg_base;		/* Common for all channels */
+	void __iomem *reg_base;		/* first channel base address */
+	u8 led_cache;			/* leds state cache */
+
+	/* PCIExpressCard i2c data */
+	struct i2c_algo_bit_data i2c_bit;
+	struct i2c_adapter led_chip;
+	struct delayed_work led_work;	/* led delayed work */
+	int chan_count;
+	struct peak_pciec_chan channel[PEAK_PCI_CHAN_MAX];
+};
+
+/* "normal" pci register write callback is overloaded for leds control */
+static void peak_pci_write_reg(const struct sja1000_priv *priv,
+			       int port, u8 val);
+
+static inline void pita_set_scl_highz(struct peak_pciec_card *card)
+{
+	u8 gp_outen = readb(card->cfg_base + PITA_GPOEN) & ~PITA_GPIN_SCL;
+	writeb(gp_outen, card->cfg_base + PITA_GPOEN);
+}
+
+static inline void pita_set_sda_highz(struct peak_pciec_card *card)
+{
+	u8 gp_outen = readb(card->cfg_base + PITA_GPOEN) & ~PITA_GPIN_SDA;
+	writeb(gp_outen, card->cfg_base + PITA_GPOEN);
+}
+
+static void peak_pciec_init_pita_gpio(struct peak_pciec_card *card)
+{
+	/* raise SCL & SDA GPIOs to high-Z */
+	pita_set_scl_highz(card);
+	pita_set_sda_highz(card);
+}
+
+static void pita_setsda(void *data, int state)
+{
+	struct peak_pciec_card *card = (struct peak_pciec_card *)data;
+	u8 gp_out, gp_outen;
+
+	/* set output sda always to 0 */
+	gp_out = readb(card->cfg_base + PITA_GPOUT) & ~PITA_GPIN_SDA;
+	writeb(gp_out, card->cfg_base + PITA_GPOUT);
+
+	/* control output sda with GPOEN */
+	gp_outen = readb(card->cfg_base + PITA_GPOEN);
+	if (state)
+		gp_outen &= ~PITA_GPIN_SDA;
+	else
+		gp_outen |= PITA_GPIN_SDA;
+
+	writeb(gp_outen, card->cfg_base + PITA_GPOEN);
+}
+
+static void pita_setscl(void *data, int state)
+{
+	struct peak_pciec_card *card = (struct peak_pciec_card *)data;
+	u8 gp_out, gp_outen;
+
+	/* set output scl always to 0 */
+	gp_out = readb(card->cfg_base + PITA_GPOUT) & ~PITA_GPIN_SCL;
+	writeb(gp_out, card->cfg_base + PITA_GPOUT);
+
+	/* control output scl with GPOEN */
+	gp_outen = readb(card->cfg_base + PITA_GPOEN);
+	if (state)
+		gp_outen &= ~PITA_GPIN_SCL;
+	else
+		gp_outen |= PITA_GPIN_SCL;
+
+	writeb(gp_outen, card->cfg_base + PITA_GPOEN);
+}
+
+static int pita_getsda(void *data)
+{
+	struct peak_pciec_card *card = (struct peak_pciec_card *)data;
+
+	/* set tristate */
+	pita_set_sda_highz(card);
+
+	return (readb(card->cfg_base + PITA_GPIN) & PITA_GPIN_SDA) ? 1 : 0;
+}
+
+static int pita_getscl(void *data)
+{
+	struct peak_pciec_card *card = (struct peak_pciec_card *)data;
+
+	/* set tristate */
+	pita_set_scl_highz(card);
+
+	return (readb(card->cfg_base + PITA_GPIN) & PITA_GPIN_SCL) ? 1 : 0;
+}
+
+/*
+ * write commands to the LED chip though the I2C-bus of the PCAN-PCIeC
+ */
+static int peak_pciec_write_pca9553(struct peak_pciec_card *card,
+				    u8 offset, u8 data)
+{
+	u8 buffer[2] = {
+		offset,
+		data
+	};
+	struct i2c_msg msg = {
+		.addr = PCA9553_1_SLAVEADDR,
+		.len = 2,
+		.buf = buffer,
+	};
+	int ret;
+
+	/* cache led mask */
+	if ((offset == 5) && (data == card->led_cache))
+		return 0;
+
+	ret = i2c_transfer(&card->led_chip, &msg, 1);
+	if (ret < 0)
+		return ret;
+
+	if (offset == 5)
+		card->led_cache = data;
+
+	return 0;
+}
+
+/*
+ * delayed work callback used to control the LEDs
+ */
+static void peak_pciec_led_work(struct work_struct *work)
+{
+	struct peak_pciec_card *card =
+		container_of(work, struct peak_pciec_card, led_work.work);
+	struct net_device *netdev;
+	u8 new_led = card->led_cache;
+	int i, up_count = 0;
+
+	/* first check what is to do */
+	for (i = 0; i < card->chan_count; i++) {
+		/* default is: not configured */
+		new_led &= ~PCA9553_LED_MASK(i);
+		new_led |= PCA9553_LED_ON(i);
+
+		netdev = card->channel[i].netdev;
+		if (!netdev || !(netdev->flags & IFF_UP))
+			continue;
+
+		up_count++;
+
+		/* no activity (but configured) */
+		new_led &= ~PCA9553_LED_MASK(i);
+		new_led |= PCA9553_LED_SLOW(i);
+
+		/* if bytes counters changed, set fast blinking led */
+		if (netdev->stats.rx_bytes != card->channel[i].prev_rx_bytes) {
+			card->channel[i].prev_rx_bytes = netdev->stats.rx_bytes;
+			new_led &= ~PCA9553_LED_MASK(i);
+			new_led |= PCA9553_LED_FAST(i);
+		}
+		if (netdev->stats.tx_bytes != card->channel[i].prev_tx_bytes) {
+			card->channel[i].prev_tx_bytes = netdev->stats.tx_bytes;
+			new_led &= ~PCA9553_LED_MASK(i);
+			new_led |= PCA9553_LED_FAST(i);
+		}
+	}
+
+	/* check if LS0 settings changed, only update i2c if so */
+	peak_pciec_write_pca9553(card, 5, new_led);
+
+	/* restart timer (except if no more configured channels) */
+	if (up_count)
+		schedule_delayed_work(&card->led_work, HZ);
+}
+
+/*
+ * set LEDs blinking state
+ */
+static void peak_pciec_set_leds(struct peak_pciec_card *card, u8 led_mask, u8 s)
+{
+	u8 new_led = card->led_cache;
+	int i;
+
+	/* first check what is to do */
+	for (i = 0; i < card->chan_count; i++)
+		if (led_mask & PCA9553_LED(i)) {
+			new_led &= ~PCA9553_LED_MASK(i);
+			new_led |= PCA9553_LED_STATE(s, i);
+		}
+
+	/* check if LS0 settings changed, only update i2c if so */
+	peak_pciec_write_pca9553(card, 5, new_led);
+}
+
+/*
+ * start one second delayed work to control LEDs
+ */
+static void peak_pciec_start_led_work(struct peak_pciec_card *card)
+{
+	if (!delayed_work_pending(&card->led_work))
+		schedule_delayed_work(&card->led_work, HZ);
+}
+
+/*
+ * stop LEDs delayed work
+ */
+static void peak_pciec_stop_led_work(struct peak_pciec_card *card)
+{
+	cancel_delayed_work_sync(&card->led_work);
+}
+
+/*
+ * initialize the PCA9553 4-bit I2C-bus LED chip
+ */
+static int peak_pciec_init_leds(struct peak_pciec_card *card)
+{
+	int err;
+
+	/* prescaler for frequency 0: "SLOW" = 1 Hz = "44" */
+	err = peak_pciec_write_pca9553(card, 1, 44 / 1);
+	if (err)
+		return err;
+
+	/* duty cycle 0: 50% */
+	err = peak_pciec_write_pca9553(card, 2, 0x80);
+	if (err)
+		return err;
+
+	/* prescaler for frequency 1: "FAST" = 5 Hz */
+	err = peak_pciec_write_pca9553(card, 3, 44 / 5);
+	if (err)
+		return err;
+
+	/* duty cycle 1: 50% */
+	err = peak_pciec_write_pca9553(card, 4, 0x80);
+	if (err)
+		return err;
+
+	/* switch LEDs to initial state */
+	return peak_pciec_write_pca9553(card, 5, PCA9553_LS0_INIT);
+}
+
+/*
+ * restore LEDs state to off peak_pciec_leds_exit
+ */
+static void peak_pciec_leds_exit(struct peak_pciec_card *card)
+{
+	/* switch LEDs to off */
+	peak_pciec_write_pca9553(card, 5, PCA9553_LED_OFF_ALL);
+}
+
+/*
+ * normal write sja1000 register method overloaded to catch when controller
+ * is started or stopped, to control leds
+ */
+static void peak_pciec_write_reg(const struct sja1000_priv *priv,
+				 int port, u8 val)
+{
+	struct peak_pci_chan *chan = priv->priv;
+	struct peak_pciec_card *card = chan->pciec_card;
+	int c = (priv->reg_base - card->reg_base) / PEAK_PCI_CHAN_SIZE;
+
+	/* sja1000 register changes control the leds state */
+	if (port == REG_MOD)
+		switch (val) {
+		case MOD_RM:
+			/* Reset Mode: set led on */
+			peak_pciec_set_leds(card, PCA9553_LED(c), PCA9553_ON);
+			break;
+		case 0x00:
+			/* Normal Mode: led slow blinking and start led timer */
+			peak_pciec_set_leds(card, PCA9553_LED(c), PCA9553_SLOW);
+			peak_pciec_start_led_work(card);
+			break;
+		default:
+			break;
+		}
+
+	/* call base function */
+	peak_pci_write_reg(priv, port, val);
+}
+
+static struct i2c_algo_bit_data peak_pciec_i2c_bit_ops = {
+	.setsda	= pita_setsda,
+	.setscl	= pita_setscl,
+	.getsda	= pita_getsda,
+	.getscl	= pita_getscl,
+	.udelay	= 10,
+	.timeout = HZ,
+};
+
+static int peak_pciec_probe(struct pci_dev *pdev, struct net_device *dev)
+{
+	struct sja1000_priv *priv = netdev_priv(dev);
+	struct peak_pci_chan *chan = priv->priv;
+	struct peak_pciec_card *card;
+	int err;
+
+	/* copy i2c object address from 1st channel */
+	if (chan->prev_dev) {
+		struct sja1000_priv *prev_priv = netdev_priv(chan->prev_dev);
+		struct peak_pci_chan *prev_chan = prev_priv->priv;
+
+		card = prev_chan->pciec_card;
+		if (!card)
+			return -ENODEV;
+
+	/* channel is the first one: do the init part */
+	} else {
+		/* create the bit banging I2C adapter structure */
+		card = kzalloc(sizeof(struct peak_pciec_card), GFP_KERNEL);
+		if (!card) {
+			dev_err(&pdev->dev,
+				 "failed allocating memory for i2c chip\n");
+			return -ENOMEM;
+		}
+
+		card->cfg_base = chan->cfg_base;
+		card->reg_base = priv->reg_base;
+
+		card->led_chip.owner = THIS_MODULE;
+		card->led_chip.dev.parent = &pdev->dev;
+		card->led_chip.algo_data = &card->i2c_bit;
+		strncpy(card->led_chip.name, "peak_i2c",
+			sizeof(card->led_chip.name));
+
+		card->i2c_bit = peak_pciec_i2c_bit_ops;
+		card->i2c_bit.udelay = 10;
+		card->i2c_bit.timeout = HZ;
+		card->i2c_bit.data = card;
+
+		peak_pciec_init_pita_gpio(card);
+
+		err = i2c_bit_add_bus(&card->led_chip);
+		if (err) {
+			dev_err(&pdev->dev, "i2c init failed\n");
+			goto pciec_init_err_1;
+		}
+
+		err = peak_pciec_init_leds(card);
+		if (err) {
+			dev_err(&pdev->dev, "leds hardware init failed\n");
+			goto pciec_init_err_2;
+		}
+
+		INIT_DELAYED_WORK(&card->led_work, peak_pciec_led_work);
+		/* PCAN-ExpressCard needs its own callback for leds */
+		priv->write_reg = peak_pciec_write_reg;
+	}
+
+	chan->pciec_card = card;
+	card->channel[card->chan_count++].netdev = dev;
+
+	return 0;
+
+pciec_init_err_2:
+	i2c_del_adapter(&card->led_chip);
+
+pciec_init_err_1:
+	peak_pciec_init_pita_gpio(card);
+	kfree(card);
+
+	return err;
+}
+
+static void peak_pciec_remove(struct peak_pciec_card *card)
+{
+	peak_pciec_stop_led_work(card);
+	peak_pciec_leds_exit(card);
+	i2c_del_adapter(&card->led_chip);
+	peak_pciec_init_pita_gpio(card);
+	kfree(card);
+}
+
+#else /* CONFIG_CAN_PEAK_PCIEC */
+
+/*
+ * Placebo functions when PCAN-ExpressCard support is not selected
+ */
+static inline int peak_pciec_probe(struct pci_dev *pdev, struct net_device *dev)
+{
+	return -ENODEV;
+}
+
+static inline void peak_pciec_remove(struct peak_pciec_card *card)
+{
+}
+#endif /* CONFIG_CAN_PEAK_PCIEC */
+
 static u8 peak_pci_read_reg(const struct sja1000_priv *priv, int port)
 {
 	return readb(priv->reg_base + (port << 2));
@@ -188,17 +637,31 @@ static int __devinit peak_pci_probe(struct pci_dev *pdev,
 
 		SET_NETDEV_DEV(dev, &pdev->dev);
 
+		/* Create chain of SJA1000 devices */
+		chan->prev_dev = pci_get_drvdata(pdev);
+		pci_set_drvdata(pdev, dev);
+
+		/*
+		 * PCAN-ExpressCard needs some additional i2c init.
+		 * This must be done *before* register_sja1000dev() but
+		 * *after* devices linkage
+		 */
+		if (pdev->device == PEAK_PCIEC_DEVICE_ID) {
+			err = peak_pciec_probe(pdev, dev);
+			if (err) {
+				dev_err(&pdev->dev,
+					"failed to probe device (err %d)\n",
+					err);
+				goto failure_free_dev;
+			}
+		}
+
 		err = register_sja1000dev(dev);
 		if (err) {
 			dev_err(&pdev->dev, "failed to register device\n");
-			free_sja1000dev(dev);
-			goto failure_remove_channels;
+			goto failure_free_dev;
 		}
 
-		/* Create chain of SJA1000 devices */
-		chan->prev_dev = pci_get_drvdata(pdev);
-		pci_set_drvdata(pdev, dev);
-
 		dev_info(&pdev->dev,
 			 "%s at reg_base=0x%p cfg_base=0x%p irq=%d\n",
 			 dev->name, priv->reg_base, chan->cfg_base, dev->irq);
@@ -209,10 +672,15 @@ static int __devinit peak_pci_probe(struct pci_dev *pdev,
 
 	return 0;
 
+failure_free_dev:
+	pci_set_drvdata(pdev, chan->prev_dev);
+	free_sja1000dev(dev);
+
 failure_remove_channels:
 	/* Disable interrupts */
 	writew(0x0, cfg_base + PITA_ICR + 2);
 
+	chan = NULL;
 	for (dev = pci_get_drvdata(pdev); dev; dev = chan->prev_dev) {
 		unregister_sja1000dev(dev);
 		free_sja1000dev(dev);
@@ -220,6 +688,10 @@ failure_remove_channels:
 		chan = priv->priv;
 	}
 
+	/* free any PCIeC resources too */
+	if (chan && chan->pciec_card)
+		peak_pciec_remove(chan->pciec_card);
+
 	pci_iounmap(pdev, reg_base);
 
 failure_unmap_cfg_base:
@@ -251,8 +723,13 @@ static void __devexit peak_pci_remove(struct pci_dev *pdev)
 		unregister_sja1000dev(dev);
 		free_sja1000dev(dev);
 		dev = chan->prev_dev;
-		if (!dev)
+
+		if (!dev) {
+			/* do that only for first channel */
+			if (chan->pciec_card)
+				peak_pciec_remove(chan->pciec_card);
 			break;
+		}
 		priv = netdev_priv(dev);
 		chan = priv->priv;
 	}
diff --git a/drivers/net/can/sja1000/peak_pcmcia.c b/drivers/net/can/sja1000/peak_pcmcia.c
new file mode 100644
index 000000000000..ec6bd9d1b2af
--- /dev/null
+++ b/drivers/net/can/sja1000/peak_pcmcia.c
@@ -0,0 +1,753 @@
+/*
+ * Copyright (C) 2010-2012 Stephane Grosjean <s.grosjean@peak-system.com>
+ *
+ * CAN driver for PEAK-System PCAN-PC Card
+ * Derived from the PCAN project file driver/src/pcan_pccard.c
+ * Copyright (C) 2006-2010 PEAK System-Technik GmbH
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License
+ * as published by the Free Software Foundation
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/netdevice.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/io.h>
+#include <pcmcia/cistpl.h>
+#include <pcmcia/ds.h>
+#include <linux/can.h>
+#include <linux/can/dev.h>
+#include "sja1000.h"
+
+MODULE_AUTHOR("Stephane Grosjean <s.grosjean@peak-system.com>");
+MODULE_DESCRIPTION("CAN driver for PEAK-System PCAN-PC Cards");
+MODULE_LICENSE("GPL v2");
+MODULE_SUPPORTED_DEVICE("PEAK PCAN-PC Card");
+
+/* PEAK-System PCMCIA driver name */
+#define PCC_NAME		"peak_pcmcia"
+
+#define PCC_CHAN_MAX		2
+
+#define PCC_CAN_CLOCK		(16000000 / 2)
+
+#define PCC_MANF_ID		0x0377
+#define PCC_CARD_ID		0x0001
+
+#define PCC_CHAN_SIZE		0x20
+#define PCC_CHAN_OFF(c)		((c) * PCC_CHAN_SIZE)
+#define PCC_COMN_OFF		(PCC_CHAN_OFF(PCC_CHAN_MAX))
+#define PCC_COMN_SIZE		0x40
+
+/* common area registers */
+#define PCC_CCR			0x00
+#define PCC_CSR			0x02
+#define PCC_CPR			0x04
+#define PCC_SPI_DIR		0x06
+#define PCC_SPI_DOR		0x08
+#define PCC_SPI_ADR		0x0a
+#define PCC_SPI_IR		0x0c
+#define PCC_FW_MAJOR		0x10
+#define PCC_FW_MINOR		0x12
+
+/* CCR bits */
+#define PCC_CCR_CLK_16		0x00
+#define PCC_CCR_CLK_10		0x01
+#define PCC_CCR_CLK_21		0x02
+#define PCC_CCR_CLK_8		0x03
+#define PCC_CCR_CLK_MASK	PCC_CCR_CLK_8
+
+#define PCC_CCR_RST_CHAN(c)	(0x01 << ((c) + 2))
+#define PCC_CCR_RST_ALL		(PCC_CCR_RST_CHAN(0) | PCC_CCR_RST_CHAN(1))
+#define PCC_CCR_RST_MASK	PCC_CCR_RST_ALL
+
+/* led selection bits */
+#define PCC_LED(c)		(1 << (c))
+#define PCC_LED_ALL		(PCC_LED(0) | PCC_LED(1))
+
+/* led state value */
+#define PCC_LED_ON		0x00
+#define PCC_LED_FAST		0x01
+#define PCC_LED_SLOW		0x02
+#define PCC_LED_OFF		0x03
+
+#define PCC_CCR_LED_CHAN(s, c)	((s) << (((c) + 2) << 1))
+
+#define PCC_CCR_LED_ON_CHAN(c)		PCC_CCR_LED_CHAN(PCC_LED_ON, c)
+#define PCC_CCR_LED_FAST_CHAN(c)	PCC_CCR_LED_CHAN(PCC_LED_FAST, c)
+#define PCC_CCR_LED_SLOW_CHAN(c)	PCC_CCR_LED_CHAN(PCC_LED_SLOW, c)
+#define PCC_CCR_LED_OFF_CHAN(c)		PCC_CCR_LED_CHAN(PCC_LED_OFF, c)
+#define PCC_CCR_LED_MASK_CHAN(c)	PCC_CCR_LED_OFF_CHAN(c)
+#define PCC_CCR_LED_OFF_ALL		(PCC_CCR_LED_OFF_CHAN(0) | \
+					 PCC_CCR_LED_OFF_CHAN(1))
+#define PCC_CCR_LED_MASK		PCC_CCR_LED_OFF_ALL
+
+#define PCC_CCR_INIT	(PCC_CCR_CLK_16 | PCC_CCR_RST_ALL | PCC_CCR_LED_OFF_ALL)
+
+/* CSR bits */
+#define PCC_CSR_SPI_BUSY		0x04
+
+/* time waiting for SPI busy (prevent from infinite loop) */
+#define PCC_SPI_MAX_BUSY_WAIT_MS	3
+
+/* max count of reading the SPI status register waiting for a change */
+/* (prevent from infinite loop) */
+#define PCC_WRITE_MAX_LOOP		1000
+
+/* max nb of int handled by that isr in one shot (prevent from infinite loop) */
+#define PCC_ISR_MAX_LOOP		10
+
+/* EEPROM chip instruction set */
+/* note: EEPROM Read/Write instructions include A8 bit */
+#define PCC_EEP_WRITE(a)	(0x02 | (((a) & 0x100) >> 5))
+#define PCC_EEP_READ(a)		(0x03 | (((a) & 0x100) >> 5))
+#define PCC_EEP_WRDI		0x04	/* EEPROM Write Disable */
+#define PCC_EEP_RDSR		0x05	/* EEPROM Read Status Register */
+#define PCC_EEP_WREN		0x06	/* EEPROM Write Enable */
+
+/* EEPROM Status Register bits */
+#define PCC_EEP_SR_WEN		0x02	/* EEPROM SR Write Enable bit */
+#define PCC_EEP_SR_WIP		0x01	/* EEPROM SR Write In Progress bit */
+
+/*
+ * The board configuration is probably following:
+ * RX1 is connected to ground.
+ * TX1 is not connected.
+ * CLKO is not connected.
+ * Setting the OCR register to 0xDA is a good idea.
+ * This means normal output mode, push-pull and the correct polarity.
+ */
+#define PCC_OCR			(OCR_TX0_PUSHPULL | OCR_TX1_PUSHPULL)
+
+/*
+ * In the CDR register, you should set CBP to 1.
+ * You will probably also want to set the clock divider value to 7
+ * (meaning direct oscillator output) because the second SJA1000 chip
+ * is driven by the first one CLKOUT output.
+ */
+#define PCC_CDR			(CDR_CBP | CDR_CLKOUT_MASK)
+
+struct pcan_channel {
+	struct net_device *netdev;
+	unsigned long prev_rx_bytes;
+	unsigned long prev_tx_bytes;
+};
+
+/* PCAN-PC Card private structure */
+struct pcan_pccard {
+	struct pcmcia_device *pdev;
+	int chan_count;
+	struct pcan_channel channel[PCC_CHAN_MAX];
+	u8 ccr;
+	u8 fw_major;
+	u8 fw_minor;
+	void __iomem *ioport_addr;
+	struct timer_list led_timer;
+};
+
+static struct pcmcia_device_id pcan_table[] = {
+	PCMCIA_DEVICE_MANF_CARD(PCC_MANF_ID, PCC_CARD_ID),
+	PCMCIA_DEVICE_NULL,
+};
+
+MODULE_DEVICE_TABLE(pcmcia, pcan_table);
+
+static void pcan_set_leds(struct pcan_pccard *card, u8 mask, u8 state);
+
+/*
+ * start timer which controls leds state
+ */
+static void pcan_start_led_timer(struct pcan_pccard *card)
+{
+	if (!timer_pending(&card->led_timer))
+		mod_timer(&card->led_timer, jiffies + HZ);
+}
+
+/*
+ * stop the timer which controls leds state
+ */
+static void pcan_stop_led_timer(struct pcan_pccard *card)
+{
+	del_timer_sync(&card->led_timer);
+}
+
+/*
+ * read a sja1000 register
+ */
+static u8 pcan_read_canreg(const struct sja1000_priv *priv, int port)
+{
+	return ioread8(priv->reg_base + port);
+}
+
+/*
+ * write a sja1000 register
+ */
+static void pcan_write_canreg(const struct sja1000_priv *priv, int port, u8 v)
+{
+	struct pcan_pccard *card = priv->priv;
+	int c = (priv->reg_base - card->ioport_addr) / PCC_CHAN_SIZE;
+
+	/* sja1000 register changes control the leds state */
+	if (port == REG_MOD)
+		switch (v) {
+		case MOD_RM:
+			/* Reset Mode: set led on */
+			pcan_set_leds(card, PCC_LED(c), PCC_LED_ON);
+			break;
+		case 0x00:
+			/* Normal Mode: led slow blinking and start led timer */
+			pcan_set_leds(card, PCC_LED(c), PCC_LED_SLOW);
+			pcan_start_led_timer(card);
+			break;
+		default:
+			break;
+		}
+
+	iowrite8(v, priv->reg_base + port);
+}
+
+/*
+ * read a register from the common area
+ */
+static u8 pcan_read_reg(struct pcan_pccard *card, int port)
+{
+	return ioread8(card->ioport_addr + PCC_COMN_OFF + port);
+}
+
+/*
+ * write a register into the common area
+ */
+static void pcan_write_reg(struct pcan_pccard *card, int port, u8 v)
+{
+	/* cache ccr value */
+	if (port == PCC_CCR) {
+		if (card->ccr == v)
+			return;
+		card->ccr = v;
+	}
+
+	iowrite8(v, card->ioport_addr + PCC_COMN_OFF + port);
+}
+
+/*
+ * check whether the card is present by checking its fw version numbers
+ * against values read at probing time.
+ */
+static inline int pcan_pccard_present(struct pcan_pccard *card)
+{
+	return ((pcan_read_reg(card, PCC_FW_MAJOR) == card->fw_major) &&
+		(pcan_read_reg(card, PCC_FW_MINOR) == card->fw_minor));
+}
+
+/*
+ * wait for SPI engine while it is busy
+ */
+static int pcan_wait_spi_busy(struct pcan_pccard *card)
+{
+	unsigned long timeout = jiffies +
+				msecs_to_jiffies(PCC_SPI_MAX_BUSY_WAIT_MS) + 1;
+
+	/* be sure to read status at least once after sleeping */
+	while (pcan_read_reg(card, PCC_CSR) & PCC_CSR_SPI_BUSY) {
+		if (time_after(jiffies, timeout))
+			return -EBUSY;
+		schedule();
+	}
+
+	return 0;
+}
+
+/*
+ * write data in device eeprom
+ */
+static int pcan_write_eeprom(struct pcan_pccard *card, u16 addr, u8 v)
+{
+	u8 status;
+	int err, i;
+
+	/* write instruction enabling write */
+	pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_WREN);
+	err = pcan_wait_spi_busy(card);
+	if (err)
+		goto we_spi_err;
+
+	/* wait until write enabled */
+	for (i = 0; i < PCC_WRITE_MAX_LOOP; i++) {
+		/* write instruction reading the status register */
+		pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_RDSR);
+		err = pcan_wait_spi_busy(card);
+		if (err)
+			goto we_spi_err;
+
+		/* get status register value and check write enable bit */
+		status = pcan_read_reg(card, PCC_SPI_DIR);
+		if (status & PCC_EEP_SR_WEN)
+			break;
+	}
+
+	if (i >= PCC_WRITE_MAX_LOOP) {
+		dev_err(&card->pdev->dev,
+			"stop waiting to be allowed to write in eeprom\n");
+		return -EIO;
+	}
+
+	/* set address and data */
+	pcan_write_reg(card, PCC_SPI_ADR, addr & 0xff);
+	pcan_write_reg(card, PCC_SPI_DOR, v);
+
+	/*
+	 * write instruction with bit[3] set according to address value:
+	 * if addr refers to upper half of the memory array: bit[3] = 1
+	 */
+	pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_WRITE(addr));
+	err = pcan_wait_spi_busy(card);
+	if (err)
+		goto we_spi_err;
+
+	/* wait while write in progress */
+	for (i = 0; i < PCC_WRITE_MAX_LOOP; i++) {
+		/* write instruction reading the status register */
+		pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_RDSR);
+		err = pcan_wait_spi_busy(card);
+		if (err)
+			goto we_spi_err;
+
+		/* get status register value and check write in progress bit */
+		status = pcan_read_reg(card, PCC_SPI_DIR);
+		if (!(status & PCC_EEP_SR_WIP))
+			break;
+	}
+
+	if (i >= PCC_WRITE_MAX_LOOP) {
+		dev_err(&card->pdev->dev,
+			"stop waiting for write in eeprom to complete\n");
+		return -EIO;
+	}
+
+	/* write instruction disabling write */
+	pcan_write_reg(card, PCC_SPI_IR, PCC_EEP_WRDI);
+	err = pcan_wait_spi_busy(card);
+	if (err)
+		goto we_spi_err;
+
+	return 0;
+
+we_spi_err:
+	dev_err(&card->pdev->dev,
+		"stop waiting (spi engine always busy) err %d\n", err);
+
+	return err;
+}
+
+static void pcan_set_leds(struct pcan_pccard *card, u8 led_mask, u8 state)
+{
+	u8 ccr = card->ccr;
+	int i;
+
+	for (i = 0; i < card->chan_count; i++)
+		if (led_mask & PCC_LED(i)) {
+			/* clear corresponding led bits in ccr */
+			ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+			/* then set new bits */
+			ccr |= PCC_CCR_LED_CHAN(state, i);
+		}
+
+	/* real write only if something has changed in ccr */
+	pcan_write_reg(card, PCC_CCR, ccr);
+}
+
+/*
+ * enable/disable CAN connectors power
+ */
+static inline void pcan_set_can_power(struct pcan_pccard *card, int onoff)
+{
+	int err;
+
+	err = pcan_write_eeprom(card, 0, !!onoff);
+	if (err)
+		dev_err(&card->pdev->dev,
+			"failed setting power %s to can connectors (err %d)\n",
+			(onoff) ? "on" : "off", err);
+}
+
+/*
+ * set leds state according to channel activity
+ */
+static void pcan_led_timer(unsigned long arg)
+{
+	struct pcan_pccard *card = (struct pcan_pccard *)arg;
+	struct net_device *netdev;
+	int i, up_count = 0;
+	u8 ccr;
+
+	ccr = card->ccr;
+	for (i = 0; i < card->chan_count; i++) {
+		/* default is: not configured */
+		ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+		ccr |= PCC_CCR_LED_ON_CHAN(i);
+
+		netdev = card->channel[i].netdev;
+		if (!netdev || !(netdev->flags & IFF_UP))
+			continue;
+
+		up_count++;
+
+		/* no activity (but configured) */
+		ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+		ccr |= PCC_CCR_LED_SLOW_CHAN(i);
+
+		/* if bytes counters changed, set fast blinking led */
+		if (netdev->stats.rx_bytes != card->channel[i].prev_rx_bytes) {
+			card->channel[i].prev_rx_bytes = netdev->stats.rx_bytes;
+			ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+			ccr |= PCC_CCR_LED_FAST_CHAN(i);
+		}
+		if (netdev->stats.tx_bytes != card->channel[i].prev_tx_bytes) {
+			card->channel[i].prev_tx_bytes = netdev->stats.tx_bytes;
+			ccr &= ~PCC_CCR_LED_MASK_CHAN(i);
+			ccr |= PCC_CCR_LED_FAST_CHAN(i);
+		}
+	}
+
+	/* write the new leds state */
+	pcan_write_reg(card, PCC_CCR, ccr);
+
+	/* restart timer (except if no more configured channels) */
+	if (up_count)
+		mod_timer(&card->led_timer, jiffies + HZ);
+}
+
+/*
+ * interrupt service routine
+ */
+static irqreturn_t pcan_isr(int irq, void *dev_id)
+{
+	struct pcan_pccard *card = dev_id;
+	int irq_handled;
+
+	/* prevent from infinite loop */
+	for (irq_handled = 0; irq_handled < PCC_ISR_MAX_LOOP; irq_handled++) {
+		/* handle shared interrupt and next loop */
+		int nothing_to_handle = 1;
+		int i;
+
+		/* check interrupt for each channel */
+		for (i = 0; i < card->chan_count; i++) {
+			struct net_device *netdev;
+
+			/*
+			 * check whether the card is present before calling
+			 * sja1000_interrupt() to speed up hotplug detection
+			 */
+			if (!pcan_pccard_present(card)) {
+				/* card unplugged during isr */
+				return IRQ_NONE;
+			}
+
+			/*
+			 * should check whether all or SJA1000_MAX_IRQ
+			 * interrupts have been handled: loop again to be sure.
+			 */
+			netdev = card->channel[i].netdev;
+			if (netdev &&
+			    sja1000_interrupt(irq, netdev) == IRQ_HANDLED)
+				nothing_to_handle = 0;
+		}
+
+		if (nothing_to_handle)
+			break;
+	}
+
+	return (irq_handled) ? IRQ_HANDLED : IRQ_NONE;
+}
+
+/*
+ * free all resources used by the channels and switch off leds and can power
+ */
+static void pcan_free_channels(struct pcan_pccard *card)
+{
+	int i;
+	u8 led_mask = 0;
+
+	for (i = 0; i < card->chan_count; i++) {
+		struct net_device *netdev;
+		char name[IFNAMSIZ];
+
+		led_mask |= PCC_LED(i);
+
+		netdev = card->channel[i].netdev;
+		if (!netdev)
+			continue;
+
+		strncpy(name, netdev->name, IFNAMSIZ);
+
+		unregister_sja1000dev(netdev);
+
+		free_sja1000dev(netdev);
+
+		dev_info(&card->pdev->dev, "%s removed\n", name);
+	}
+
+	/* do it only if device not removed */
+	if (pcan_pccard_present(card)) {
+		pcan_set_leds(card, led_mask, PCC_LED_OFF);
+		pcan_set_can_power(card, 0);
+	}
+}
+
+/*
+ * check if a CAN controller is present at the specified location
+ */
+static inline int pcan_channel_present(struct sja1000_priv *priv)
+{
+	/* make sure SJA1000 is in reset mode */
+	pcan_write_canreg(priv, REG_MOD, 1);
+	pcan_write_canreg(priv, REG_CDR, CDR_PELICAN);
+
+	/* read reset-values */
+	if (pcan_read_canreg(priv, REG_CDR) == CDR_PELICAN)
+		return 1;
+
+	return 0;
+}
+
+static int pcan_add_channels(struct pcan_pccard *card)
+{
+	struct pcmcia_device *pdev = card->pdev;
+	int i, err = 0;
+	u8 ccr = PCC_CCR_INIT;
+
+	/* init common registers (reset channels and leds off) */
+	card->ccr = ~ccr;
+	pcan_write_reg(card, PCC_CCR, ccr);
+
+	/* wait 2ms before unresetting channels */
+	mdelay(2);
+
+	ccr &= ~PCC_CCR_RST_ALL;
+	pcan_write_reg(card, PCC_CCR, ccr);
+
+	/* create one network device per channel detected */
+	for (i = 0; i < ARRAY_SIZE(card->channel); i++) {
+		struct net_device *netdev;
+		struct sja1000_priv *priv;
+
+		netdev = alloc_sja1000dev(0);
+		if (!netdev) {
+			err = -ENOMEM;
+			break;
+		}
+
+		/* update linkages */
+		priv = netdev_priv(netdev);
+		priv->priv = card;
+		SET_NETDEV_DEV(netdev, &pdev->dev);
+
+		priv->irq_flags = IRQF_SHARED;
+		netdev->irq = pdev->irq;
+		priv->reg_base = card->ioport_addr + PCC_CHAN_OFF(i);
+
+		/* check if channel is present */
+		if (!pcan_channel_present(priv)) {
+			dev_err(&pdev->dev, "channel %d not present\n", i);
+			free_sja1000dev(netdev);
+			continue;
+		}
+
+		priv->read_reg  = pcan_read_canreg;
+		priv->write_reg = pcan_write_canreg;
+		priv->can.clock.freq = PCC_CAN_CLOCK;
+		priv->ocr = PCC_OCR;
+		priv->cdr = PCC_CDR;
+
+		/* Neither a slave device distributes the clock */
+		if (i > 0)
+			priv->cdr |= CDR_CLK_OFF;
+
+		priv->flags |= SJA1000_CUSTOM_IRQ_HANDLER;
+
+		/* register SJA1000 device */
+		err = register_sja1000dev(netdev);
+		if (err) {
+			free_sja1000dev(netdev);
+			continue;
+		}
+
+		card->channel[i].netdev = netdev;
+		card->chan_count++;
+
+		/* set corresponding led on in the new ccr */
+		ccr &= ~PCC_CCR_LED_OFF_CHAN(i);
+
+		dev_info(&pdev->dev,
+			"%s on channel %d at 0x%p irq %d\n",
+			netdev->name, i, priv->reg_base, pdev->irq);
+	}
+
+	/* write new ccr (change leds state) */
+	pcan_write_reg(card, PCC_CCR, ccr);
+
+	return err;
+}
+
+static int pcan_conf_check(struct pcmcia_device *pdev, void *priv_data)
+{
+	pdev->resource[0]->flags &= ~IO_DATA_PATH_WIDTH;
+	pdev->resource[0]->flags |= IO_DATA_PATH_WIDTH_8; /* only */
+	pdev->io_lines = 10;
+
+	/* This reserves IO space but doesn't actually enable it */
+	return pcmcia_request_io(pdev);
+}
+
+/*
+ * free all resources used by the device
+ */
+static void pcan_free(struct pcmcia_device *pdev)
+{
+	struct pcan_pccard *card = pdev->priv;
+
+	if (!card)
+		return;
+
+	free_irq(pdev->irq, card);
+	pcan_stop_led_timer(card);
+
+	pcan_free_channels(card);
+
+	ioport_unmap(card->ioport_addr);
+
+	kfree(card);
+	pdev->priv = NULL;
+}
+
+/*
+ * setup PCMCIA socket and probe for PEAK-System PC-CARD
+ */
+static int __devinit pcan_probe(struct pcmcia_device *pdev)
+{
+	struct pcan_pccard *card;
+	int err;
+
+	pdev->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO;
+
+	err = pcmcia_loop_config(pdev, pcan_conf_check, NULL);
+	if (err) {
+		dev_err(&pdev->dev, "pcmcia_loop_config() error %d\n", err);
+		goto probe_err_1;
+	}
+
+	if (!pdev->irq) {
+		dev_err(&pdev->dev, "no irq assigned\n");
+		err = -ENODEV;
+		goto probe_err_1;
+	}
+
+	err = pcmcia_enable_device(pdev);
+	if (err) {
+		dev_err(&pdev->dev, "pcmcia_enable_device failed err=%d\n",
+			err);
+		goto probe_err_1;
+	}
+
+	card = kzalloc(sizeof(struct pcan_pccard), GFP_KERNEL);
+	if (!card) {
+		dev_err(&pdev->dev, "couldn't allocate card memory\n");
+		err = -ENOMEM;
+		goto probe_err_2;
+	}
+
+	card->pdev = pdev;
+	pdev->priv = card;
+
+	/* sja1000 api uses iomem */
+	card->ioport_addr = ioport_map(pdev->resource[0]->start,
+					resource_size(pdev->resource[0]));
+	if (!card->ioport_addr) {
+		dev_err(&pdev->dev, "couldn't map io port into io memory\n");
+		err = -ENOMEM;
+		goto probe_err_3;
+	}
+	card->fw_major = pcan_read_reg(card, PCC_FW_MAJOR);
+	card->fw_minor = pcan_read_reg(card, PCC_FW_MINOR);
+
+	/* display board name and firware version */
+	dev_info(&pdev->dev, "PEAK-System pcmcia card %s fw %d.%d\n",
+		pdev->prod_id[1] ? pdev->prod_id[1] : "PCAN-PC Card",
+		card->fw_major, card->fw_minor);
+
+	/* detect available channels */
+	pcan_add_channels(card);
+	if (!card->chan_count)
+		goto probe_err_4;
+
+	/* init the timer which controls the leds */
+	init_timer(&card->led_timer);
+	card->led_timer.function = pcan_led_timer;
+	card->led_timer.data = (unsigned long)card;
+
+	/* request the given irq */
+	err = request_irq(pdev->irq, &pcan_isr, IRQF_SHARED, PCC_NAME, card);
+	if (err) {
+		dev_err(&pdev->dev, "couldn't request irq%d\n", pdev->irq);
+		goto probe_err_5;
+	}
+
+	/* power on the connectors */
+	pcan_set_can_power(card, 1);
+
+	return 0;
+
+probe_err_5:
+	/* unregister can devices from network */
+	pcan_free_channels(card);
+
+probe_err_4:
+	ioport_unmap(card->ioport_addr);
+
+probe_err_3:
+	kfree(card);
+	pdev->priv = NULL;
+
+probe_err_2:
+	pcmcia_disable_device(pdev);
+
+probe_err_1:
+	return err;
+}
+
+/*
+ * release claimed resources
+ */
+static void pcan_remove(struct pcmcia_device *pdev)
+{
+	pcan_free(pdev);
+	pcmcia_disable_device(pdev);
+}
+
+static struct pcmcia_driver pcan_driver = {
+	.name = PCC_NAME,
+	.probe = pcan_probe,
+	.remove = pcan_remove,
+	.id_table = pcan_table,
+};
+
+static int __init pcan_init(void)
+{
+	return pcmcia_register_driver(&pcan_driver);
+}
+module_init(pcan_init);
+
+static void __exit pcan_exit(void)
+{
+	pcmcia_unregister_driver(&pcan_driver);
+}
+module_exit(pcan_exit);
diff --git a/drivers/net/can/sja1000/plx_pci.c b/drivers/net/can/sja1000/plx_pci.c
index c7f3d4ea1167..a227586ddd52 100644
--- a/drivers/net/can/sja1000/plx_pci.c
+++ b/drivers/net/can/sja1000/plx_pci.c
@@ -43,7 +43,8 @@ MODULE_SUPPORTED_DEVICE("Adlink PCI-7841/cPCI-7841, "
 			"TEWS TECHNOLOGIES TPMC810, "
 			"esd CAN-PCI/CPCI/PCI104/200, "
 			"esd CAN-PCI/PMC/266, "
-			"esd CAN-PCIe/2000")
+			"esd CAN-PCIe/2000, "
+			"IXXAT PC-I 04/PCI")
 MODULE_LICENSE("GPL v2");
 
 #define PLX_PCI_MAX_CHAN 2
@@ -121,6 +122,10 @@ struct plx_pci_card {
 #define ESD_PCI_SUB_SYS_ID_PCIE2000	0x0200
 #define ESD_PCI_SUB_SYS_ID_PCI104200	0x0501
 
+#define IXXAT_PCI_VENDOR_ID		0x10b5
+#define IXXAT_PCI_DEVICE_ID		0x9050
+#define IXXAT_PCI_SUB_SYS_ID		0x2540
+
 #define MARATHON_PCI_DEVICE_ID		0x2715
 
 #define TEWS_PCI_VENDOR_ID		0x1498
@@ -193,6 +198,14 @@ static struct plx_pci_card_info plx_pci_card_info_esd2000 __devinitdata = {
 	/* based on PEX8311 */
 };
 
+static struct plx_pci_card_info plx_pci_card_info_ixxat __devinitdata = {
+	"IXXAT PC-I 04/PCI", 2,
+	PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
+	{0, 0x00, 0x00}, { {2, 0x00, 0x80}, {2, 0x200, 0x80} },
+	&plx_pci_reset_common
+	/* based on PLX9050 */
+};
+
 static struct plx_pci_card_info plx_pci_card_info_marathon __devinitdata = {
 	"Marathon CAN-bus-PCI", 2,
 	PLX_PCI_CAN_CLOCK, PLX_PCI_OCR, PLX_PCI_CDR,
@@ -267,6 +280,13 @@ static DEFINE_PCI_DEVICE_TABLE(plx_pci_tbl) = {
 		(kernel_ulong_t)&plx_pci_card_info_esd2000
 	},
 	{
+		/* IXXAT PC-I 04/PCI card */
+		IXXAT_PCI_VENDOR_ID, IXXAT_PCI_DEVICE_ID,
+		PCI_ANY_ID, IXXAT_PCI_SUB_SYS_ID,
+		0, 0,
+		(kernel_ulong_t)&plx_pci_card_info_ixxat
+	},
+	{
 		/* Marathon CAN-bus-PCI card */
 		PCI_VENDOR_ID_PLX, MARATHON_PCI_DEVICE_ID,
 		PCI_ANY_ID, PCI_ANY_ID,
diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c
index 192b0d118df4..5e10472371ed 100644
--- a/drivers/net/can/sja1000/sja1000.c
+++ b/drivers/net/can/sja1000/sja1000.c
@@ -133,7 +133,7 @@ static void set_reset_mode(struct net_device *dev)
 		status = priv->read_reg(priv, REG_MOD);
 	}
 
-	dev_err(dev->dev.parent, "setting SJA1000 into reset mode failed!\n");
+	netdev_err(dev, "setting SJA1000 into reset mode failed!\n");
 }
 
 static void set_normal_mode(struct net_device *dev)
@@ -161,7 +161,7 @@ static void set_normal_mode(struct net_device *dev)
 		status = priv->read_reg(priv, REG_MOD);
 	}
 
-	dev_err(dev->dev.parent, "setting SJA1000 into normal mode failed!\n");
+	netdev_err(dev, "setting SJA1000 into normal mode failed!\n");
 }
 
 static void sja1000_start(struct net_device *dev)
@@ -214,8 +214,7 @@ static int sja1000_set_bittiming(struct net_device *dev)
 	if (priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES)
 		btr1 |= 0x80;
 
-	dev_info(dev->dev.parent,
-		 "setting BTR0=0x%02x BTR1=0x%02x\n", btr0, btr1);
+	netdev_info(dev, "setting BTR0=0x%02x BTR1=0x%02x\n", btr0, btr1);
 
 	priv->write_reg(priv, REG_BTR0, btr0);
 	priv->write_reg(priv, REG_BTR1, btr1);
@@ -383,7 +382,7 @@ static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status)
 
 	if (isrc & IRQ_DOI) {
 		/* data overrun interrupt */
-		dev_dbg(dev->dev.parent, "data overrun interrupt\n");
+		netdev_dbg(dev, "data overrun interrupt\n");
 		cf->can_id |= CAN_ERR_CRTL;
 		cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW;
 		stats->rx_over_errors++;
@@ -393,7 +392,7 @@ static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status)
 
 	if (isrc & IRQ_EI) {
 		/* error warning interrupt */
-		dev_dbg(dev->dev.parent, "error warning interrupt\n");
+		netdev_dbg(dev, "error warning interrupt\n");
 
 		if (status & SR_BS) {
 			state = CAN_STATE_BUS_OFF;
@@ -434,7 +433,7 @@ static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status)
 	}
 	if (isrc & IRQ_EPI) {
 		/* error passive interrupt */
-		dev_dbg(dev->dev.parent, "error passive interrupt\n");
+		netdev_dbg(dev, "error passive interrupt\n");
 		if (status & SR_ES)
 			state = CAN_STATE_ERROR_PASSIVE;
 		else
@@ -442,7 +441,7 @@ static int sja1000_err(struct net_device *dev, uint8_t isrc, uint8_t status)
 	}
 	if (isrc & IRQ_ALI) {
 		/* arbitration lost interrupt */
-		dev_dbg(dev->dev.parent, "arbitration lost interrupt\n");
+		netdev_dbg(dev, "arbitration lost interrupt\n");
 		alc = priv->read_reg(priv, REG_ALC);
 		priv->can.can_stats.arbitration_lost++;
 		stats->tx_errors++;
@@ -503,7 +502,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id)
 			return IRQ_NONE;
 
 		if (isrc & IRQ_WUI)
-			dev_warn(dev->dev.parent, "wakeup interrupt\n");
+			netdev_warn(dev, "wakeup interrupt\n");
 
 		if (isrc & IRQ_TI) {
 			/* transmission complete interrupt */
@@ -533,7 +532,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id)
 		priv->post_irq(priv);
 
 	if (n >= SJA1000_MAX_IRQ)
-		dev_dbg(dev->dev.parent, "%d messages handled in ISR", n);
+		netdev_dbg(dev, "%d messages handled in ISR", n);
 
 	return (n) ? IRQ_HANDLED : IRQ_NONE;
 }