talos-op-linux/drivers/tty/serial, branch master

Fix up remaining devm_ioremap_nocache() in SGI IOC3 8250 UART driver

2020-02-08T22:19:39+00:00

This is a merge error on my part - the driver was merged into mainline by commit c5951e7c8ee5 ("Merge tag 'mips_5.6' of git://../mips/linux") over a week ago, but nobody apparently noticed that it didn't actually build due to still having a reference to the devm_ioremap_nocache() function, removed a few days earlier through commit 6a1000bd2703 ("Merge tag 'ioremap-5.6' of git://../ioremap"). Apparently this didn't get any build testing anywhere. Not perhaps all that surprising: it's restricted to 64-bit MIPS only, and only with the new SGI_MFD_IOC3 support enabled. I only noticed because the ioremap conflicts in the ARM SoC driver update made me check there weren't any others hiding, and I found this one. Signed-off-by: Linus Torvalds

Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2020-02-08T22:04:19+00:00

Pull ARM SoC-related driver updates from Olof Johansson: "Various driver updates for platforms: - Nvidia: Fuse support for Tegra194, continued memory controller pieces for Tegra30 - NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC - NXP/FSL: i.MX8MP SoC driver pieces - TI Keystone: ring accelerator driver - Qualcomm: SCM driver cleanup/refactoring + support for new SoCs. - Xilinx ZynqMP: feature checking interface for firmware. Mailbox communication for power management - Overall support patch set for cpuidle on more complex hierarchies (PSCI-based) and misc cleanups, refactorings of Marvell, TI, other platforms" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits) drivers: soc: xilinx: Use mailbox IPI callback dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists MAINTAINERS: Add brcmstb PCIe controller entry soc/tegra: fuse: Unmap registers once they are not needed anymore soc/tegra: fuse: Correct straps' address for older Tegra124 device trees soc/tegra: fuse: Warn if straps are not ready soc/tegra: fuse: Cache values of straps and Chip ID registers memory: tegra30-emc: Correct error message for timed out auto calibration memory: tegra30-emc: Firm up hardware programming sequence memory: tegra30-emc: Firm up suspend/resume sequence soc/tegra: regulators: Do nothing if voltage is unchanged memory: tegra: Correct reset value of xusb_hostr soc/tegra: fuse: Add APB DMA dependency for Tegra20 bus: tegra-aconnect: Remove PM_CLK dependency dt-bindings: mediatek: add MT6765 power dt-bindings soc: mediatek: cmdq: delete not used define memory: tegra: Add support for the Tegra194 memory controller memory: tegra: Only include support for enabled SoCs memory: tegra: Support DVFS on Tegra186 and later ...

Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux

2020-01-31T19:28:31+00:00

Pull MIPS changes from Paul Burton: "Nothing too big or scary in here: - Support mremap() for the VDSO, primarily to allow CRIU to restore the VDSO to its checkpointed location. - Restore the MIPS32 cBPF JIT, after having reverted the enablement of the eBPF JIT for MIPS32 systems in the 5.5 cycle. - Improve cop0 counter synchronization behaviour whilst onlining CPUs by running with interrupts disabled. - Better match FPU behaviour when emulating multiply-accumulate instructions on pre-r6 systems that implement IEEE754-2008 style MACs. - Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to take advantage of instructions introduced by r2. - Support for the Ingenic X1000 SoC & the really nice little CU Neo development board that's using it. - Support for WMAC on GARDENA Smart Gateway devices. - Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in preparation for introducing IP35 (Origin 3*) support. - Various Kconfig & Makefile cleanups" * tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits) MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel MIPS: Loongson64: Disable exec hazard MIPS: Loongson64: Bump ISA level to MIPSR2 MIPS: Make DIEI support as a config option MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too" MIPS: asm: local: add barriers for Loongson MIPS: Loongson64: Select mac2008 only feature MIPS: Add MAC2008 Support Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel" MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again) MIPS: make CPU_HAS_LOAD_STORE_LR opt-out MIPS: generic: don't unconditionally select PINCTRL MIPS: don't explicitly select LIBFDT in Kconfig MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts MIPS: SGI-IP30: Check for valid pointer before using it MIPS: syscalls: fix indentation of the 'SYSNR' message MIPS: boot: fix typo in 'vmlinux.lzma.its' target MIPS: fix indentation of the 'RELOCS' message dt-bindings: Document loongson vendor-prefix MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi. ...

Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

2020-01-29T18:13:27+00:00

Pull tty/serial driver updates from Greg KH: "Here are the big set of tty and serial driver updates for 5.6-rc1 Included in here are: - dummy_con cleanups (touches lots of arch code) - sysrq logic cleanups (touches lots of serial drivers) - samsung driver fixes (wasn't really being built) - conmakeshash move to tty subdir out of scripts - lots of small tty/serial driver updates All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits) tty: n_hdlc: Use flexible-array member and struct_size() helper tty: baudrate: SPARC supports few more baud rates tty: baudrate: Synchronise baud_table[] and baud_bits[] tty: serial: meson_uart: Add support for kernel debugger serial: imx: fix a race condition in receive path serial: 8250_bcm2835aux: Document struct bcm2835aux_data serial: 8250_bcm2835aux: Use generic remapping code serial: 8250_bcm2835aux: Allocate uart_8250_port on stack serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER serial: 8250_bcm2835aux: Fix line mismatch on driver unbind serial_core: Remove unused member in uart_port vt: Correct comment documenting do_take_over_console() vt: Delete comment referencing non-existent unbind_con_driver() arch/xtensa/setup: Drop dummy_con initialization arch/x86/setup: Drop dummy_con initialization arch/unicore32/setup: Drop dummy_con initialization arch/sparc/setup: Drop dummy_con initialization arch/sh/setup: Drop dummy_con initialization arch/s390/setup: Drop dummy_con initialization ...

tty: serial: meson_uart: Add support for kernel debugger

2020-01-22T09:22:31+00:00

The kgdb invokes the poll_put_char and poll_get_char when communicating with the host. This patch implement the serial polling hooks for the meson_uart to be used for KGDB debugging over serial line. Signed-off-by: Julien Masson Link: https://lore.kernel.org/r/867e1klo48.fsf@julienm-fedora-R90NQGV9.i-did-not-set--mail-host-address--so-tickle-me Signed-off-by: Greg Kroah-Hartman

serial: imx: fix a race condition in receive path

2020-01-22T09:22:31+00:00

The main irq handler function starts by first masking disabled interrupts in the status register values to ensure to only handle enabled interrupts. This is important as when the RX path in the hardware is disabled reading the RX fifo results in an external abort. This checking must be done under the port lock, otherwise the following can happen: CPU1 | CPU2 | irq triggers as there are chars | in the RX fifo | | grab port lock imx_uart_int finds RRDY enabled | and calls imx_uart_rxint which | has to wait for port lock | | disable RX (e.g. because we're | using RS485 with !RX_DURING_TX) | | release port lock read from RX fifo with RX | disabled => exception | So take the port lock only once in imx_uart_int() instead of in the functions called from there. Reported-by: Andre Renaud Cc: stable@vger.kernel.org Signed-off-by: Uwe Kleine-König Link: https://lore.kernel.org/r/20200121071702.20150-1-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Document struct bcm2835aux_data

2020-01-22T09:22:31+00:00

Document the driver private data of the BCM2835 auxiliary UART so that upcoming commits may add further members with proper kerneldoc. Signed-off-by: Lukas Wunner Reviewed-by: Matthias Brugger Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/aea363c27fd541dba96d2ebfeee4f596c6d34932.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Use generic remapping code

2020-01-22T09:22:30+00:00

On probe the bcm2835aux UART driver misreports the register base address as 0x0: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 50000000) is a 16550 That's because the driver remaps the registers itself. Take advantage of the generic remapping code in serial8250_request_std_resource() to get a message with the correct address and to simplify the driver. Signed-off-by: Lukas Wunner Cc: Martin Sperl Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/7d1a9bdb05090d8e465fd15cd26d6e81538d07f9.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Allocate uart_8250_port on stack

2020-01-22T09:22:30+00:00

The bcm2835aux UART driver stores a struct uart_8250_port in its private data even though it's only passed once to serial8250_register_8250_port() (which copies all relevant data) and becomes obsolete afterwards. Allocate the struct on the stack instead for simplicity and to conserve memory. The driver also initializes a spinlock in the struct which is never used. Drop that as well. Signed-off-by: Lukas Wunner Cc: Martin Sperl Reviewed-by: Matthias Brugger Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/421d3aed4c34cc8447ac9c26c320961f1b787f11.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER

2020-01-22T09:22:30+00:00

Suppress a gratuitous error message if serial8250_register_8250_port() returns -EPROBE_DEFER. Signed-off-by: Lukas Wunner Reviewed-by: Matthias Brugger Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/6aea0eacf3bfa73fe2d81082cc723265413410c8.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman