talos-op-linux/drivers/tty/serial/8250, branch master

Fix up remaining devm_ioremap_nocache() in SGI IOC3 8250 UART driver

2020-02-08T22:19:39+00:00

This is a merge error on my part - the driver was merged into mainline by commit c5951e7c8ee5 ("Merge tag 'mips_5.6' of git://../mips/linux") over a week ago, but nobody apparently noticed that it didn't actually build due to still having a reference to the devm_ioremap_nocache() function, removed a few days earlier through commit 6a1000bd2703 ("Merge tag 'ioremap-5.6' of git://../ioremap"). Apparently this didn't get any build testing anywhere. Not perhaps all that surprising: it's restricted to 64-bit MIPS only, and only with the new SGI_MFD_IOC3 support enabled. I only noticed because the ioremap conflicts in the ARM SoC driver update made me check there weren't any others hiding, and I found this one. Signed-off-by: Linus Torvalds

Merge tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux

2020-01-31T19:28:31+00:00

Pull MIPS changes from Paul Burton: "Nothing too big or scary in here: - Support mremap() for the VDSO, primarily to allow CRIU to restore the VDSO to its checkpointed location. - Restore the MIPS32 cBPF JIT, after having reverted the enablement of the eBPF JIT for MIPS32 systems in the 5.5 cycle. - Improve cop0 counter synchronization behaviour whilst onlining CPUs by running with interrupts disabled. - Better match FPU behaviour when emulating multiply-accumulate instructions on pre-r6 systems that implement IEEE754-2008 style MACs. - Loongson64 kernels now build using the MIPS64r2 ISA, allowing them to take advantage of instructions introduced by r2. - Support for the Ingenic X1000 SoC & the really nice little CU Neo development board that's using it. - Support for WMAC on GARDENA Smart Gateway devices. - Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in preparation for introducing IP35 (Origin 3*) support. - Various Kconfig & Makefile cleanups" * tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits) MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel MIPS: Loongson64: Disable exec hazard MIPS: Loongson64: Bump ISA level to MIPSR2 MIPS: Make DIEI support as a config option MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too" MIPS: asm: local: add barriers for Loongson MIPS: Loongson64: Select mac2008 only feature MIPS: Add MAC2008 Support Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel" MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again) MIPS: make CPU_HAS_LOAD_STORE_LR opt-out MIPS: generic: don't unconditionally select PINCTRL MIPS: don't explicitly select LIBFDT in Kconfig MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts MIPS: SGI-IP30: Check for valid pointer before using it MIPS: syscalls: fix indentation of the 'SYSNR' message MIPS: boot: fix typo in 'vmlinux.lzma.its' target MIPS: fix indentation of the 'RELOCS' message dt-bindings: Document loongson vendor-prefix MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi. ...

Merge tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty

2020-01-29T18:13:27+00:00

Pull tty/serial driver updates from Greg KH: "Here are the big set of tty and serial driver updates for 5.6-rc1 Included in here are: - dummy_con cleanups (touches lots of arch code) - sysrq logic cleanups (touches lots of serial drivers) - samsung driver fixes (wasn't really being built) - conmakeshash move to tty subdir out of scripts - lots of small tty/serial driver updates All of these have been in linux-next for a while with no reported issues" * tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits) tty: n_hdlc: Use flexible-array member and struct_size() helper tty: baudrate: SPARC supports few more baud rates tty: baudrate: Synchronise baud_table[] and baud_bits[] tty: serial: meson_uart: Add support for kernel debugger serial: imx: fix a race condition in receive path serial: 8250_bcm2835aux: Document struct bcm2835aux_data serial: 8250_bcm2835aux: Use generic remapping code serial: 8250_bcm2835aux: Allocate uart_8250_port on stack serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER serial: 8250_bcm2835aux: Fix line mismatch on driver unbind serial_core: Remove unused member in uart_port vt: Correct comment documenting do_take_over_console() vt: Delete comment referencing non-existent unbind_con_driver() arch/xtensa/setup: Drop dummy_con initialization arch/x86/setup: Drop dummy_con initialization arch/unicore32/setup: Drop dummy_con initialization arch/sparc/setup: Drop dummy_con initialization arch/sh/setup: Drop dummy_con initialization arch/s390/setup: Drop dummy_con initialization ...

serial: 8250_bcm2835aux: Document struct bcm2835aux_data

2020-01-22T09:22:31+00:00

Document the driver private data of the BCM2835 auxiliary UART so that upcoming commits may add further members with proper kerneldoc. Signed-off-by: Lukas Wunner Reviewed-by: Matthias Brugger Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/aea363c27fd541dba96d2ebfeee4f596c6d34932.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Use generic remapping code

2020-01-22T09:22:30+00:00

On probe the bcm2835aux UART driver misreports the register base address as 0x0: ttyS0 at MMIO 0x0 (irq = 53, base_baud = 50000000) is a 16550 That's because the driver remaps the registers itself. Take advantage of the generic remapping code in serial8250_request_std_resource() to get a message with the correct address and to simplify the driver. Signed-off-by: Lukas Wunner Cc: Martin Sperl Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/7d1a9bdb05090d8e465fd15cd26d6e81538d07f9.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Allocate uart_8250_port on stack

2020-01-22T09:22:30+00:00

The bcm2835aux UART driver stores a struct uart_8250_port in its private data even though it's only passed once to serial8250_register_8250_port() (which copies all relevant data) and becomes obsolete afterwards. Allocate the struct on the stack instead for simplicity and to conserve memory. The driver also initializes a spinlock in the struct which is never used. Drop that as well. Signed-off-by: Lukas Wunner Cc: Martin Sperl Reviewed-by: Matthias Brugger Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/421d3aed4c34cc8447ac9c26c320961f1b787f11.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER

2020-01-22T09:22:30+00:00

Suppress a gratuitous error message if serial8250_register_8250_port() returns -EPROBE_DEFER. Signed-off-by: Lukas Wunner Reviewed-by: Matthias Brugger Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/6aea0eacf3bfa73fe2d81082cc723265413410c8.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER

2020-01-22T09:22:30+00:00

Suppress a gratuitous error message if devm_clk_get() returns -EPROBE_DEFER. Signed-off-by: Phil Elwell [lukas: extend commit message] Signed-off-by: Lukas Wunner Reviewed-by: Matthias Brugger Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/deafc13cdfd7a31c6a81b0db95adcd3599accc26.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

serial: 8250_bcm2835aux: Fix line mismatch on driver unbind

2020-01-22T09:22:29+00:00

Unbinding the bcm2835aux UART driver raises the following error if the maximum number of 8250 UARTs is set to 1 (via the 8250.nr_uarts module parameter or CONFIG_SERIAL_8250_RUNTIME_UARTS): (NULL device *): Removing wrong port: a6f80333 != fa20408b That's because bcm2835aux_serial_probe() retrieves UART line number 1 from the devicetree and stores it in data->uart.port.line, while serial8250_register_8250_port() instead uses UART line number 0, which is stored in data->line. On driver unbind, bcm2835aux_serial_remove() uses data->uart.port.line, which contains the wrong number. Fix it. The issue does not occur if the maximum number of 8250 UARTs is >= 2. Fixes: bdc5f3009580 ("serial: bcm2835: add driver for bcm2835-aux-uart") Signed-off-by: Lukas Wunner Cc: stable@vger.kernel.org # v4.6+ Cc: Martin Sperl Reviewed-by: Nicolas Saenz Julienne Tested-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/912ccf553c5258135c6d7e8f404a101ef320f0f4.1579175223.git.lukas@wunner.de Signed-off-by: Greg Kroah-Hartman

tty/serial: 8250_exar: use true,false for bool variable

2020-01-14T13:34:04+00:00

Fixes coccicheck warning: drivers/tty/serial/8250/8250_exar.c:189:6-17: WARNING: Assignment of 0/1 to bool variable drivers/tty/serial/8250/8250_exar.c:197:3-14: WARNING: Assignment of 0/1 to bool variable drivers/tty/serial/8250/8250_exar.c:199:3-14: WARNING: Assignment of 0/1 to bool variable Reported-by: Hulk Robot Signed-off-by: Zheng Bin Link: https://lore.kernel.org/r/1578881777-65475-5-git-send-email-zhengbin13@huawei.com Signed-off-by: Greg Kroah-Hartman