talos-op-linux/arch/arm/mach-tegra, branch master

ARM: tegra: Use clk_m CPU on Tegra124 LP1 resume

2020-01-08T11:58:46+00:00

Configure the clock controller to set an alternate clock for the CPU when it receives an IRQ during LP1 (system suspend). Specifically, use clk_m (the crystal) rather than clk_s (a 32KHz clock). Such an IRQ will be the LP1 wake event. This reduces the amount of time taken to resume from LP1. NVIDIA's downstream kernel executes this code on both Tegra30 and Tegra124, so it appears OK to make this change unconditionally. Signed-off-by: Stephen Warren Signed-off-by: Thierry Reding

ARM: tegra: Modify reshift divider during LP1

2020-01-08T11:57:53+00:00

The reshift hardware module implements the RAM re-repair process. This module uses PLLP as an input clock during LP1 resume. The input divider for this clock is typically set for PLLP's normal rate. During LP1 resume, PLLP is bypassed and so runs at the crystal rate, which is much slower. Consequently, decrease the divider so that the reshift module runs at a reasonable rate during LP1 resume. NVIDIA's downstream kernel code only does this if not compiled for Tegra30, so the added code is made conditional upon the chip ID. Signed-off-by: Stephen Warren Signed-off-by: Thierry Reding

ARM: tegra: Enable PLLP bypass during Tegra124 LP1

2020-01-08T11:57:05+00:00

For a little over a year, U-Boot has configured the flow controller to perform automatic RAM re-repair on off->on power transitions of the CPU rail[1]. This is mandatory for correct operation of Tegra124. However, RAM re-repair relies on certain clocks, which the kernel must enable and leave running. PLLP is one of those clocks. This clock is shut down during LP1 in order to save power. Enable bypass (which I believe routes osc_div_clk, essentially the crystal clock, to the PLL output) so that this clock signal toggles even though the PLL is not active. This is required so that LP1 power mode (system suspend) operates correctly. The bypass configuration must then be undone when resuming from LP1, so that all peripheral clocks run at the expected rate. Without this, many peripherals won't work correctly; for example, the UART baud rate would be incorrect. NVIDIA's downstream kernel code only does this if not compiled for Tegra30, so the added code is made conditional upon the chip ID. NVIDIA's downstream code makes this change conditional upon the active CPU cluster. The upstream kernel currently doesn't support cluster switching, so this patch doesn't test the active CPU cluster ID. [1] 3cc7942a4ae5 ARM: tegra: implement RAM repair Reported-by: Jonathan Hunter Cc: stable@vger.kernel.org Signed-off-by: Stephen Warren Signed-off-by: Thierry Reding

Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

2019-12-05T19:38:40+00:00

Pull ARM SoC platform updates from Olof Johansson: "Most of these are for MMP (seeing a bunch of cleanups and refactorings for the first time in a while), and for OMAP (a bunch of cleanups and added support for voltage controller on OMAP4430)" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (51 commits) ARM: OMAP2+: Add missing put_device() call in omapdss_init_of() OMAP2: fixup doc comments in omap_device ARM: OMAP1: drop duplicated dependency on ARCH_OMAP1 ARM: ASPEED: update default ARCH_NR_GPIO for ARCH_ASPEED ARM: imx: use generic function to exit coherency ARM: tegra: Use WFE for power-gating on Tegra30 ARM: tegra: Fix FLOW_CTLR_HALT register clobbering by tegra_resume() ARM: exynos: Enable exynos-asv driver for ARCH_EXYNOS ARM: s3c: Rename s5p_usb_phy functions ARM: s3c: Rename s3c64xx_spi_setname() function ARM: imx: Add serial number support for i.MX6/7 SoCs ARM: imx: Drop imx_anatop_usb_chrg_detect_disable() arm64: Introduce config for S32 ARM: hisi: drop useless depend on ARCH_MULTI_V7 arm64: realtek: Select reset controller ARM: shmobile: rcar-gen2: Drop legacy DT clock support ARM: OMAP2+: Remove duplicated include from pmic-cpcap.c ARM: OMAP1: ams-delta FIQ: Fix a typo ("Initiaize") MAINTAINERS: Add logicpd-som-lv and logicpd-torpedo to OMAP TREE ARM: OMAP2+: pdata-quirks: drop TI_ST/KIM support ...

cpuidle: Introduce cpuidle_driver_state_disabled() for driver quirks

2019-11-19T09:35:13+00:00

Commit 99e98d3fb100 ("cpuidle: Consolidate disabled state checks") overlooked the fact that the imx6q and tegra20 cpuidle drivers use the "disabled" field in struct cpuidle_state for quirks which trigger after the initialization of cpuidle, so reading the initial value of that field is not sufficient for those drivers. In order to allow them to implement the quirks without using the "disabled" field in struct cpuidle_state, introduce a new helper function and modify them to use it. Fixes: 99e98d3fb100 ("cpuidle: Consolidate disabled state checks") Reported-by: Len Brown Signed-off-by: Rafael J. Wysocki

ARM: tegra: Use WFE for power-gating on Tegra30

2019-10-29T13:32:01+00:00

Turned out that WFI doesn't work reliably on Tegra30 as a trigger for the power-gating, it causes CPU hang under some circumstances like having memory controller running of PLLP. The TRM doc states that WFI should be used for the Big-Little "Cluster Switch", while WFE for the power-gating. Hence let's use the WFE for CPU0 power-gating, like it is done for the power-gating of a secondary cores. This fixes CPU hang after entering LP2 with memory running off PLLP. Acked-by: Peter De Schrijver Signed-off-by: Dmitry Osipenko Tested-by: Peter Geis Signed-off-by: Thierry Reding

ARM: tegra: Fix FLOW_CTLR_HALT register clobbering by tegra_resume()

2019-10-29T13:31:35+00:00

There is an unfortunate typo in the code that results in writing to FLOW_CTLR_HALT instead of FLOW_CTLR_CSR. Cc: Acked-by: Peter De Schrijver Signed-off-by: Dmitry Osipenko Signed-off-by: Thierry Reding

ARM: tegra: Mark expected switch fall-through

2019-08-10T00:45:22+00:00

Mark switch cases where we are expecting to fall through. This patch fixes the following warning: arch/arm/mach-tegra/reset.c: In function 'tegra_cpu_reset_handler_enable': arch/arm/mach-tegra/reset.c:72:3: warning: this statement may fall through [-Wimplicit-fallthrough=] tegra_cpu_reset_handler_set(reset_address); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ arch/arm/mach-tegra/reset.c:74:2: note: here case 0: ^~~~ Reported-by: Stephen Rothwell Reviewed-by: Kees Cook Signed-off-by: Gustavo A. R. Silva

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

2019-06-19T15:09:55+00:00

Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Enrico Weigelt Reviewed-by: Kate Stewart Reviewed-by: Allison Randal Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 282

2019-06-05T15:36:37+00:00

Based on 1 normalized pattern(s): this software is licensed under the terms of the gnu general public license version 2 as published by the free software foundation and may be copied distributed and modified under those terms this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 285 file(s). Signed-off-by: Thomas Gleixner Reviewed-by: Alexios Zavras Reviewed-by: Allison Randal Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de Signed-off-by: Greg Kroah-Hartman