1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
config DM_I2C
bool "Enable Driver Model for I2C drivers"
depends on DM
help
Enable driver model for I2C. The I2C uclass interface: probe, read,
write and speed, is implemented with the bus drivers operations,
which provide methods for bus setting and data transfer. Each chip
device (bus child) info is kept as parent platdata. The interface
is defined in include/i2c.h. When i2c bus driver supports the i2c
uclass, but the device drivers not, then DM_I2C_COMPAT config can
be used as compatibility layer.
config DM_I2C_COMPAT
bool "Enable I2C compatibility layer"
depends on DM
help
Enable old-style I2C functions for compatibility with existing code.
This option can be enabled as a temporary measure to avoid needing
to convert all code for a board in a single commit. It should not
be enabled for any board in an official release.
config I2C_CROS_EC_TUNNEL
tristate "Chrome OS EC tunnel I2C bus"
depends on CROS_EC
help
This provides an I2C bus that will tunnel i2c commands through to
the other side of the Chrome OS EC to the I2C bus connected there.
This will work whatever the interface used to talk to the EC (SPI,
I2C or LPC). Some Chromebooks use this when the hardware design
does not allow direct access to the main PMIC from the AP.
config I2C_CROS_EC_LDO
bool "Provide access to LDOs on the Chrome OS EC"
depends on CROS_EC
---help---
On many Chromebooks the main PMIC is inaccessible to the AP. This is
often dealt with by using an I2C pass-through interface provided by
the EC. On some unfortunate models (e.g. Spring) the pass-through
is not available, and an LDO message is available instead. This
option enables a driver which provides very basic access to those
regulators, via the EC. We implement this as an I2C bus which
emulates just the TPS65090 messages we know about. This is done to
avoid duplicating the logic in the TPS65090 regulator driver for
enabling/disabling an LDO.
config DM_I2C_GPIO
bool "Enable Driver Model for software emulated I2C bus driver"
depends on DM_I2C && DM_GPIO
help
Enable the i2c bus driver emulation by using the GPIOs. The bus GPIO
configuration is given by the device tree. Kernel-style device tree
bindings are supported.
Binding info: doc/device-tree-bindings/i2c/i2c-gpio.txt
config SYS_I2C_SANDBOX
bool "Sandbox I2C driver"
depends on SANDBOX && DM_I2C
help
Enable I2C support for sandbox. This is an emulation of a real I2C
bus. Devices can be attached to the bus using the device tree
which specifies the driver to use. As an example, see this device
tree fragment from sandbox.dts. It shows that the I2C bus has a
single EEPROM at address 0x2c (7-bit address) which is emulated by
the driver for "sandbox,i2c-eeprom", which is in
drivers/misc/i2c_eeprom_emul.c.
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
compatible = "sandbox,i2c";
clock-frequency = <400000>;
eeprom@2c {
reg = <0x2c>;
compatible = "i2c-eeprom";
emul {
compatible = "sandbox,i2c-eeprom";
sandbox,filename = "i2c.bin";
sandbox,size = <128>;
};
};
};
config SYS_I2C_UNIPHIER
bool "UniPhier I2C driver"
depends on ARCH_UNIPHIER && DM_I2C
default y
help
Support for UniPhier I2C controller driver. This I2C controller
is used on PH1-LD4, PH1-sLD8 or older UniPhier SoCs.
config SYS_I2C_UNIPHIER_F
bool "UniPhier FIFO-builtin I2C driver"
depends on ARCH_UNIPHIER && DM_I2C
default y
help
Support for UniPhier FIFO-builtin I2C controller driver.
This I2C controller is used on PH1-Pro4 or newer UniPhier SoCs.
source "drivers/i2c/muxes/Kconfig"
|
