summaryrefslogtreecommitdiffstats
path: root/doc/README.mpc83xx.ddrecc
blob: 0029f08759d611edead742d6323f8978ce62e792 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
Overview
========

The overall usage pattern for ECC diagnostic commands is the following:

  * (injecting errors is initially disabled)

  * define inject mask (which tells the DDR controller what type of errors
    we'll be injecting: single/multiple bit etc.)

  * enable injecting errors - from now on the controller injects errors as
    indicated in the inject mask

IMPORTANT NOTICE: enabling injecting multiple-bit errors is potentially
dangerous as such errors are NOT corrected by the controller. Therefore caution
should be taken when enabling the injection of multiple-bit errors: it is only
safe when used on a carefully selected memory area and used under control of
the 'ecc testdw' 'ecc testword' command (see example 'Injecting Multiple-Bit
Errors' below). In particular, when you simply set the multiple-bit errors in
inject mask and enable injection, U-Boot is very likely to hang quickly as the
errors will be injected when it accesses its code, data etc.


Use cases for DDR 'ecc' command:
================================

Before executing particular tests reset target board or clear status registers:

=> ecc captureclear
=> ecc errdetectclr all
=> ecc sbecnt 0


Injecting Single-Bit Errors
---------------------------

1. Set 1 bit in Data Path Error Inject Mask

=> ecc injectdatahi 1

2. Run test over some memory region

=> ecc testdw 200000 10

3. Check ECC status

=> ecc status
...
Memory Data Path Error Injection Mask High/Low: 00000001 00000000
...
Memory Single-Bit Error Management (0..255):
  Single-Bit Error Threshold: 255
  Single Bit Error Counter: 16
...
Memory Error Detect:
  Multiple Memory Errors: 0
  Multiple-Bit Error: 0
  Single-Bit Error: 0
...

16 errors were generated, Single-Bit Error flag was not set as Single Bit Error
Counter did not reach  Single-Bit Error Threshold.

4. Make sure used memory region got re-initialized with 0x0123456789abcdef

=> md 200000
00200000: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200010: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200020: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200030: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200040: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200050: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200060: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200070: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200080: deadbeef deadbeef deadbeef deadbeef    ................
00200090: deadbeef deadbeef deadbeef deadbeef    ................

Injecting Multiple-Bit Errors
-----------------------------

1. Set more than 1 bit in Data Path Error Inject Mask

=> ecc injectdatahi 1
=> ecc injectdatalo 1

2. Run test over some memory region

=> ecc testword 200000 1

3. Check ECC status

=> ecc status
...
Memory Data Path Error Injection Mask High/Low: 00000001 00000001
...
Memory Error Detect:
  Multiple Memory Errors: 0
  Multiple-Bit Error: 1
  Single-Bit Error: 0
...

The Multiple Memory Errors flags not set and Multiple-Bit Error flags are set.

4. Make sure used memory region got re-initialized with 0x0123456789abcdef

=> md 200000
00200000: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200010: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200020: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200030: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200040: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200050: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200060: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200070: 01234567 89abcdef 01234567 89abcdef    .#Eg.....#Eg....
00200080: deadbeef deadbeef deadbeef deadbeef    ................
00200090: deadbeef deadbeef deadbeef deadbeef    ................


Test Single-Bit Error Counter and Threshold
-------------------------------------------

1. Set 1 bit in Data Path Error Inject Mask

=> ecc injectdatahi 1

2. Enable error injection

=> ecc inject en

3. Let u-boot run for a with Single-Bit error injection enabled

4. Disable error injection

=> ecc inject dis

4. Check status

=> ecc status

...
Memory Single-Bit Error Management (0..255):
  Single-Bit Error Threshold: 255
  Single Bit Error Counter: 199

Memory Error Detect:
  Multiple Memory Errors: 1
  Multiple-Bit Error: 0
  Single-Bit Error: 1
...

Observe that Single-Bit Error is 'on' which means that Single-Bit Error Counter
reached Single-Bit Error Threshold. Multiple Memory Errors bit is also 'on', that
is Counter reached Threshold more than one time (it wraps back after reaching
Threshold).
OpenPOWER on IntegriCloud