summaryrefslogtreecommitdiffstats
path: root/board/bf548-ezkit/bf548-ezkit.c
blob: 88a0cd4d619b9d15ddc9ebaf1615fd76199bc4da (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
/*
 * U-boot - main board file
 *
 * Copyright (c) 2005-2008 Analog Devices Inc.
 *
 * Licensed under the GPL-2 or later.
 */

#include <common.h>
#include <netdev.h>
#include <config.h>
#include <command.h>
#include <asm/blackfin.h>

DECLARE_GLOBAL_DATA_PTR;

int checkboard(void)
{
	printf("Board: ADI BF548 EZ-Kit board\n");
	printf("       Support: http://blackfin.uclinux.org/\n");
	return 0;
}

phys_size_t initdram(int board_type)
{
	gd->bd->bi_memstart = CONFIG_SYS_SDRAM_BASE;
	gd->bd->bi_memsize = CONFIG_SYS_MAX_RAM_SIZE;
	return gd->bd->bi_memsize;
}

int board_early_init_f(void)
{
	/* Port H: PH8 - PH13 == A4 - A9
	 * address lines of the parallel asynchronous memory interface
	 */

	/************************************************
	* configure GPIO 				*
	* set port H function enable register		*
	*  configure PH8-PH13 as peripheral (not GPIO) 	*
	*************************************************/
	bfin_write_PORTH_FER(0x3F03);

	/************************************************
	* set port H MUX to configure PH8-PH13		*
	*  1st Function (MUX = 00) (bits 16-27 == 0)	*
	*  Set to address signals A4-A9 		*
	*************************************************/
	bfin_write_PORTH_MUX(0);

	/************************************************
	* set port H direction register			*
	*  enable PH8-PH13 as outputs			*
	*************************************************/
	bfin_write_PORTH_DIR_SET(0x3F00);

	/* Port I: PI0 - PH14 == A10 - A24
	 * address lines of the parallel asynchronous memory interface
	 */

	/************************************************
	* set port I function enable register		*
	*  configure PI0-PI14 as peripheral (not GPIO) 	*
	*************************************************/
	bfin_write_PORTI_FER(0x7fff);

	/**************************************************
	* set PORT I MUX to configure PI14-PI0 as	  *
	* 1st Function (MUX=00) - address signals A10-A24 *
	***************************************************/
	bfin_write_PORTI_MUX(0);

	/****************************************
	* set PORT I direction register		*
	*  enable PI0 - PI14 as outputs		*
	*****************************************/
	bfin_write_PORTI_DIR_SET(0x7fff);

	return 0;
}

#ifdef CONFIG_SMC911X
int board_eth_init(bd_t *bis)
{
	return smc911x_initialize(0, CONFIG_SMC911X_BASE);
}
#endif
OpenPOWER on IntegriCloud