/* * ti_armv7_common.h * * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ * * SPDX-License-Identifier: GPL-2.0+ * * The various ARMv7 SoCs from TI all share a number of IP blocks when * implementing a given feature. Rather than define these in every * board or even SoC common file, we define a common file to be re-used * in all cases. While technically true that some of these details are * configurable at the board design, they are common throughout SoC * reference platforms as well as custom designs and become de facto * standards. */ #ifndef __CONFIG_TI_ARMV7_COMMON_H__ #define __CONFIG_TI_ARMV7_COMMON_H__ /* Common define for many platforms. */ #define CONFIG_OMAP #define CONFIG_OMAP_COMMON #define CONFIG_SYS_GENERIC_BOARD /* * We typically do not contain NOR flash. In the cases where we do, we * undefine this later. */ #define CONFIG_SYS_NO_FLASH /* Support both device trees and ATAGs. */ #define CONFIG_OF_LIBFDT #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG /* * Our DDR memory always starts at 0x80000000 and U-Boot shall have * relocated itself to higher in memory by the time this value is used. * However, set this to a 32MB offset to allow for easier Linux kernel * booting as the default is often used as the kernel load address. */ #define CONFIG_SYS_LOAD_ADDR 0x82000000 /* * We setup defaults based on constraints from the Linux kernel, which should * also be safe elsewhere. We have the default load at 32MB into DDR (for * the kernel), FDT above 128MB (the maximum location for the end of the * kernel), and the ramdisk 512KB above that (allowing for hopefully never * seen large trees). We say all of this must be within the first 256MB * as that will normally be within the kernel lowmem and thus visible via * bootm_size and we only run on platforms with 256MB or more of memory. */ #define DEFAULT_LINUX_BOOT_ENV \ "loadaddr=0x82000000\0" \ "kernel_addr_r=0x82000000\0" \ "fdtaddr=0x88000000\0" \ "fdt_addr_r=0x88000000\0" \ "rdaddr=0x88080000\0" \ "ramdisk_addr_r=0x88080000\0" \ "bootm_size=0x10000000\0" /* * Default to a quick boot delay. */ #define CONFIG_BOOTDELAY 1 /* * DDR information. If the CONFIG_NR_DRAM_BANKS is not defined, * we say (for simplicity) that we have 1 bank, always, even when * we have more. We always start at 0x80000000, and we place the * initial stack pointer in our SRAM. Otherwise, we can define * CONFIG_NR_DRAM_BANKS before including this file. */ #ifndef CONFIG_NR_DRAM_BANKS #define CONFIG_NR_DRAM_BANKS 1 #endif #define CONFIG_SYS_SDRAM_BASE 0x80000000 #define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ GENERATED_GBL_DATA_SIZE) /* Timer information. */ #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ /* I2C IP block */ #define CONFIG_I2C #define CONFIG_CMD_I2C #define CONFIG_SYS_I2C #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 #define CONFIG_SYS_I2C_OMAP24XX /* MMC/SD IP block */ #define CONFIG_MMC #define CONFIG_GENERIC_MMC #define CONFIG_OMAP_HSMMC #define CONFIG_CMD_MMC /* McSPI IP block */ #define CONFIG_SPI #define CONFIG_OMAP3_SPI #define CONFIG_CMD_SPI /* GPIO block */ #define CONFIG_OMAP_GPIO #define CONFIG_CMD_GPIO /* * GPMC NAND block. We support 1 device and the physical address to * access CS0 at is 0x8000000. */ #ifdef CONFIG_NAND #define CONFIG_NAND_OMAP_GPMC #ifndef CONFIG_SYS_NAND_BASE #define CONFIG_SYS_NAND_BASE 0x8000000 #endif #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_CMD_NAND #endif /* * The following are general good-enough settings for U-Boot. We set a * large malloc pool as we generally have a lot of DDR, and we opt for * function over binary size in the main portion of U-Boot as this is * generally easily constrained later if needed. We enable the config * options that give us information in the environment about what board * we are on so we do not need to rely on the command prompt. We set a * console baudrate of 115200 and use the default baud rate table. */ #define CONFIG_SYS_MALLOC_LEN (16 << 20) #define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_PROMPT "U-Boot# " #define CONFIG_SYS_CONSOLE_INFO_QUIET #define CONFIG_BAUDRATE 115200 #define CONFIG_ENV_VARS_UBOOT_CONFIG /* Strongly encouraged */ #define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */ /* As stated above, the following choices are optional. */ #define CONFIG_SYS_LONGHELP #define CONFIG_AUTO_COMPLETE #define CONFIG_CMDLINE_EDITING #define CONFIG_VERSION_VARIABLE /* We set the max number of command args high to avoid HUSH bugs. */ #define CONFIG_SYS_MAXARGS 64 /* Console I/O Buffer Size */ #define CONFIG_SYS_CBSIZE 512 /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \ + sizeof(CONFIG_SYS_PROMPT) + 16) /* Boot Argument Buffer Size */ #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* * When we have SPI, NOR or NAND flash we expect to be making use of * mtdparts, both for ease of use in U-Boot and for passing information * on to the Linux kernel. */ #if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NOR) || defined(CONFIG_NAND) #define CONFIG_MTD_DEVICE /* Required for mtdparts */ #define CONFIG_CMD_MTDPARTS #endif /* * For commands to use, we take the default list and add a few other * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH * prior to this include, in order to skip a few commands. When we do * have flash, if we expect these commands they must be enabled in that * config. If desired, a specific list of desired commands can be used * instead. */ #include #define CONFIG_CMD_ASKENV #define CONFIG_CMD_ECHO #define CONFIG_CMD_BOOTZ #define CONFIG_SUPPORT_RAW_INITRD /* * Common filesystems support. When we have removable storage we * enabled a number of useful commands and support. */ #if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) #define CONFIG_DOS_PARTITION #define CONFIG_CMD_FAT #define CONFIG_FAT_WRITE #define CONFIG_CMD_EXT2 #define CONFIG_CMD_EXT4 #define CONFIG_CMD_FS_GENERIC #define CONFIG_PARTITION_UUIDS #define CONFIG_CMD_PART #endif /* * Our platforms make use of SPL to initalize the hardware (primarily * memory) enough for full U-Boot to be loaded. We also support Falcon * Mode so that the Linux kernel can be booted directly from SPL * instead, if desired. We make use of the general SPL framework found * under common/spl/. Given our generally common memory map, we set a * number of related defaults and sizes here. */ #if !defined(CONFIG_NOR_BOOT) && \ !(defined(CONFIG_QSPI_BOOT) && defined(CONFIG_AM43XX)) #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_OS_BOOT /* * Place the image at the start of the ROM defined image space (per * CONFIG_SPL_TEXT_BASE and we limit our size to the ROM-defined * downloaded image area. We initalize DRAM as soon as we can so that * we can place stack, malloc and BSS there. We load U-Boot itself into * memory at 0x80800000 for legacy reasons (to not conflict with older * SPLs). We have our BSS be placed 2MiB after this, to allow for the * default Linux kernel address of 0x80008000 to work with most sized * kernels, in the Falcon Mode case. We have the SPL malloc pool at the * end of the BSS area. We place our stack at 32MiB after the start of * DRAM to allow room for all of the above. */ #define CONFIG_SPL_STACK (CONFIG_SYS_SDRAM_BASE + (32 << 20)) #ifndef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0x80800000 #endif #ifndef CONFIG_SPL_BSS_START_ADDR #define CONFIG_SPL_BSS_START_ADDR 0x80a00000 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ #endif #ifndef CONFIG_SYS_SPL_MALLOC_START #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ CONFIG_SPL_BSS_MAX_SIZE) #define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN #endif /* RAW SD card / eMMC locations. */ #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ /* FAT sd card locations. */ #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" #ifdef CONFIG_SPL_OS_BOOT /* FAT */ #define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage" #define CONFIG_SPL_FS_LOAD_ARGS_NAME "args" /* RAW SD card / eMMC */ #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ /* spl export command */ #define CONFIG_CMD_SPL #endif #ifdef CONFIG_MMC #define CONFIG_SPL_LIBDISK_SUPPORT #define CONFIG_SPL_MMC_SUPPORT #define CONFIG_SPL_FAT_SUPPORT #endif /* General parts of the framework, required. */ #define CONFIG_SPL_I2C_SUPPORT #define CONFIG_SPL_LIBCOMMON_SUPPORT #define CONFIG_SPL_LIBGENERIC_SUPPORT #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_BOARD_INIT #ifdef CONFIG_NAND #define CONFIG_SPL_NAND_SUPPORT #define CONFIG_SPL_NAND_BASE #define CONFIG_SPL_NAND_DRIVERS #define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_MTD_SUPPORT #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #endif #endif /* !CONFIG_NOR_BOOT */ #endif /* __CONFIG_TI_ARMV7_COMMON_H__ */