/* * Configuration settings for the TechNexion TAO-3530 SOM * equipped on Thunder baseboard. * * Edward Lin * Tapani Utriainen * * Copyright (C) 2013 Stefan Roese * * SPDX-License-Identifier: GPL-2.0+ */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options */ #define CONFIG_OMAP /* in a TI OMAP core */ #define CONFIG_OMAP_GPIO #define CONFIG_OMAP_COMMON #define CONFIG_SYS_GENERIC_BOARD #define MACH_TYPE_OMAP3_TAO3530 2836 #define CONFIG_SDRC /* Has an SDRC controller */ #include /* get chip and board defs */ #include /* * Display CPU and Board information */ #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO /* Clock Defines */ #define V_OSCK 26000000 /* Clock output from T2 */ #define V_SCLK (V_OSCK >> 1) #define CONFIG_MISC_INIT_R #define CONFIG_OF_LIBFDT #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_INITRD_TAG #define CONFIG_REVISION_TAG /* * Size of malloc() pool */ #define CONFIG_SYS_MALLOC_LEN (4 << 20) #define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */ /* * Hardware drivers */ /* * NS16550 Configuration */ #define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */ #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE (-4) #define CONFIG_SYS_NS16550_CLK V_NS16550_CLK /* * select serial console configuration */ #define CONFIG_CONS_INDEX 3 #define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3 /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE #define CONFIG_BAUDRATE 115200 #define CONFIG_GENERIC_MMC #define CONFIG_MMC #define CONFIG_OMAP_HSMMC #define CONFIG_DOS_PARTITION /* GPIO banks */ #define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */ #define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */ #define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */ #define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ #define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ /* commands to include */ #include #define CONFIG_CMD_CACHE #define CONFIG_CMD_EXT2 /* EXT2 Support */ #define CONFIG_CMD_FAT /* FAT support */ #define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */ #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ #define MTDIDS_DEFAULT "nand0=nand" #define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\ "1920k(u-boot),128k(u-boot-env),"\ "4m(kernel),-(fs)" #define CONFIG_CMD_I2C /* I2C serial bus support */ #define CONFIG_CMD_MMC /* MMC support */ #define CONFIG_CMD_NAND /* NAND support */ #define CONFIG_CMD_DHCP #define CONFIG_CMD_PING #undef CONFIG_CMD_FLASH /* flinfo, erase, protect */ #undef CONFIG_CMD_FPGA /* FPGA configuration Support */ #undef CONFIG_CMD_IMI /* iminfo */ #undef CONFIG_CMD_IMLS /* List all found images */ #define CONFIG_SYS_NO_FLASH #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_OMAP34XX #define CONFIG_SYS_OMAP24_I2C_SPEED 100000 #define CONFIG_SYS_OMAP24_I2C_SLAVE 1 #define CONFIG_I2C_MULTI_BUS /* * TWL4030 */ #define CONFIG_TWL4030_POWER #define CONFIG_TWL4030_LED /* * Board NAND Info. */ #define CONFIG_SYS_NAND_QUIET_TEST #define CONFIG_NAND_OMAP_GPMC #define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */ /* to access nand */ #define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */ /* to access nand at */ /* CS0 */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */ /* devices */ #define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16 /* Environment information */ #define CONFIG_BOOTDELAY 3 #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ "console=ttyO2,115200n8\0" \ "mpurate=600\0" \ "dvi_mode=omapfb.mode=dvi:1280x720-24@60\0" \ "tv_mode=omapfb.mode=tv:ntsc\0" \ "video_mode=omapdss.def_disp=lcd vram=6M omapfb.vram=0:2M,1:2M,2:2M\0" \ "lcd_mode=omapfb.mode=lcd:800x480@60 \0" \ "extra_options= \0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ "mmcrootfstype=ext3 rootwait\0" \ "nandroot=ubi0:rootfs ubi.mtd=4\0" \ "nandrootfstype=ubifs\0" \ "mmcargs=setenv bootargs console=${console} " \ "mpurate=${mpurate} " \ "${video_mode} " \ "root=${mmcroot} " \ "rootfstype=${mmcrootfstype} " \ "${extra_options}\0" \ "nandargs=setenv bootargs console=${console} " \ "mpurate=${mpurate} " \ "${video_mode} " \ "${network_setting} " \ "root=${nandroot} " \ "rootfstype=${nandrootfstype} "\ "${extra_options}\0" \ "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source ${loadaddr}\0" \ "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs; " \ "bootm ${loadaddr}\0" \ "nandboot=echo Booting from nand ...; " \ "run nandargs; " \ "nand read ${loadaddr} 280000 400000; " \ "bootm ${loadaddr}\0" \ #define CONFIG_BOOTCOMMAND \ "if mmc rescan ${mmcdev}; then " \ "if run loadbootscript; then " \ "run bootscript; " \ "else " \ "if run loaduimage; then " \ "run mmcboot; " \ "else run nandboot; " \ "fi; " \ "fi; " \ "else run nandboot; fi" /* * Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ #define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */ #define CONFIG_SYS_PROMPT "TAO-3530 # " #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ /* turn on command-line edit/hist/auto */ #define CONFIG_CMDLINE_EDITING #define CONFIG_COMMAND_HISTORY #define CONFIG_AUTO_COMPLETE /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ sizeof(CONFIG_SYS_PROMPT) + 16) #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ /* Boot Argument Buffer Size */ #define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE) #define CONFIG_SYS_ALT_MEMTEST 1 #define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest */ /* defaults */ #define CONFIG_SYS_MEMTEST_END (0x83FFFFFF) /* 64MB */ #define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */ #define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */ /* load address */ #define CONFIG_SYS_TEXT_BASE 0x80008000 /* * OMAP3 has 12 GP timers, they can be driven by the system clock * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK). * This rate is divided by a local divisor. */ #define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2) #define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ /* * Stack sizes * * The stack sizes are set up in start.S using the settings below */ #define CONFIG_STACKSIZE (128 << 10) /* regular stack 128 KiB */ /* * Physical Memory Map */ #define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */ #define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0 #define PHYS_SDRAM_1_SIZE (32 << 20) /* at least 32 MiB */ #define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1 /* * FLASH and environment organization */ /* **** PISMO SUPPORT *** */ #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */ #define CONFIG_SYS_FLASH_BASE NAND_BASE /* Monitor at start of flash */ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE #define CONFIG_SYS_ONENAND_BASE ONENAND_MAP #define CONFIG_ENV_IS_IN_NAND 1 #define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */ #define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */ #define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) #define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET #define CONFIG_ENV_ADDR CONFIG_ENV_OFFSET #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 #define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800 #define CONFIG_SYS_INIT_RAM_SIZE 0x800 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ CONFIG_SYS_INIT_RAM_SIZE - \ GENERATED_GBL_DATA_SIZE) #define CONFIG_OMAP3_SPI /* * USB * * Currently only EHCI is enabled, the MUSB OTG controller * is not enabled. */ /* USB EHCI */ #define CONFIG_CMD_USB #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 162 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3 #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_SMSC95XX #define CONFIG_USB_ETHER #define CONFIG_USB_ETHER_RNDIS #define CONFIG_USB_STORAGE #define CONGIG_CMD_STORAGE /* Defines for SPL */ #define CONFIG_SPL_FRAMEWORK #define CONFIG_SPL_NAND_SIMPLE #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */ #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" #define CONFIG_SPL_BOARD_INIT #define CONFIG_SPL_LIBCOMMON_SUPPORT #define CONFIG_SPL_LIBDISK_SUPPORT #define CONFIG_SPL_I2C_SUPPORT #define CONFIG_SPL_LIBGENERIC_SUPPORT #define CONFIG_SPL_MMC_SUPPORT #define CONFIG_SPL_FAT_SUPPORT #define CONFIG_SPL_SERIAL_SUPPORT #define CONFIG_SPL_NAND_SUPPORT #define CONFIG_SPL_NAND_BASE #define CONFIG_SPL_NAND_DRIVERS #define CONFIG_SPL_NAND_ECC #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_POWER_SUPPORT #define CONFIG_SPL_OMAP3_ID_NAND #define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds" /* NAND boot config */ #define CONFIG_SYS_NAND_5_ADDR_CYCLE #define CONFIG_SYS_NAND_PAGE_COUNT 64 #define CONFIG_SYS_NAND_PAGE_SIZE 2048 #define CONFIG_SYS_NAND_OOBSIZE 64 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) #define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS /* * Use the ECC/OOB layout from omap_gpmc.h that matches your chip: * SP vs LP, 8bit vs 16bit: GPMC_NAND_HW_ECC_LAYOUT */ #define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ 10, 11, 12, 13 } #define CONFIG_SYS_NAND_ECCSIZE 512 #define CONFIG_SYS_NAND_ECCBYTES 3 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 #define CONFIG_SPL_TEXT_BASE 0x40200800 #define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */ /* * Use 0x80008000 as TEXT_BASE here for compatibility reasons with the * older x-loader implementations. And move the BSS area so that it * doesn't overlap with TEXT_BASE. */ #define CONFIG_SYS_TEXT_BASE 0x80008000 #define CONFIG_SPL_BSS_START_ADDR 0x80100000 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ #define CONFIG_SYS_SPL_MALLOC_START 0x80208000 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 #endif /* __CONFIG_H */