/* * Copyright (C) 2006 Freescale Semiconductor, Inc. * Dave Liu * * Copyright (C) 2007 Logic Product Development, Inc. * Peter Barada * * Copyright (C) 2007 MontaVista Software, Inc. * Anton Vorontsov * * (C) Copyright 2008 * Heiko Schocher, DENX Software Engineering, hs@denx.de. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as * published by the Free Software Foundation; either version 2 of * the License, or (at your option) any later version. */ #ifndef __CONFIG_H #define __CONFIG_H /* * High Level Configuration Options */ #define CONFIG_E300 1 /* E300 family */ #define CONFIG_QE 1 /* Has QE */ #define CONFIG_MPC83xx 1 /* MPC83xx family */ #define CONFIG_MPC8360 1 /* MPC8360 CPU specific */ #define CONFIG_KMETER1 1 /* KMETER1 board specific */ #define CONFIG_HOSTNAME kmeter1 #define CONFIG_SYS_TEXT_BASE 0xF0000000 /* include common defines/options for all Keymile boards */ #include "keymile-common.h" #define CONFIG_KM_UBI_PARTITION_NAME "ubi0" #define MTDIDS_DEFAULT "nor0=boot" #define MTDPARTS_DEFAULT \ "mtdparts=boot:768k(u-boot),128k(env),128k(envred)," \ "-(" CONFIG_KM_UBI_PARTITION_NAME ")" #define CONFIG_MISC_INIT_R 1 /* * System Clock Setup */ #define CONFIG_83XX_CLKIN 66000000 #define CONFIG_SYS_CLK_FREQ 66000000 #define CONFIG_83XX_PCICLK 66000000 /* * Hardware Reset Configuration Word */ #define CONFIG_SYS_HRCW_LOW (\ HRCWL_CSB_TO_CLKIN_4X1 | \ HRCWL_CORE_TO_CSB_2X1 | \ HRCWL_CE_PLL_VCO_DIV_2 | \ HRCWL_CE_TO_PLL_1X6 ) #define CONFIG_SYS_HRCW_HIGH (\ HRCWH_CORE_ENABLE | \ HRCWH_FROM_0X00000100 | \ HRCWH_BOOTSEQ_DISABLE | \ HRCWH_SW_WATCHDOG_DISABLE | \ HRCWH_ROM_LOC_LOCAL_16BIT | \ HRCWH_BIG_ENDIAN | \ HRCWH_LALE_EARLY | \ HRCWH_LDP_CLEAR ) /* * System IO Config */ #define CONFIG_SYS_SICRH 0x00000006 #define CONFIG_SYS_SICRL 0x00000000 /* * IMMR new address */ #define CONFIG_SYS_IMMR 0xE0000000 /* * Bus Arbitration Configuration Register (ACR) */ #define CONFIG_SYS_ACR_PIPE_DEP 3 /* pipeline depth 4 transactions */ #define CONFIG_SYS_ACR_RPTCNT 3 /* 4 consecutive transactions */ #define CONFIG_SYS_ACR_APARK 0 /* park bus to master (below) */ #define CONFIG_SYS_ACR_PARKM 3 /* parking master = QuiccEngine */ /* * DDR Setup */ #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */ #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN | \ DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) #define CFG_83XX_DDR_USES_CS0 #undef CONFIG_DDR_ECC /* * DDRCDR - DDR Control Driver Register */ #undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */ /* * Manually set up DDR parameters */ #define CONFIG_DDR_II #define CONFIG_SYS_DDR_SIZE 2048 /* MB */ #define CONFIG_SYS_DDR_CS0_BNDS 0x0000007f #define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_AP | \ CSCONFIG_ROW_BIT_13 | \ CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS) #define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 | \ SDRAM_CFG_SREN) #define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000 #define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05) #define CONFIG_SYS_DDR_INTERVAL ((0x080 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \ (0x3cf << SDRAM_INTERVAL_REFINT_SHIFT)) #define CONFIG_SYS_DDRCDR 0x40000001 #define CONFIG_SYS_DDR_MODE 0x47860452 #define CONFIG_SYS_DDR_MODE2 0x8080c000 #define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \ (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \ (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \ (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \ (0 << TIMING_CFG0_WWT_SHIFT) | \ (0 << TIMING_CFG0_RRT_SHIFT) | \ (0 << TIMING_CFG0_WRT_SHIFT) | \ (0 << TIMING_CFG0_RWT_SHIFT)) #define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_50) | \ ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \ ( 2 << TIMING_CFG1_ACTTOACT_SHIFT) | \ ( 3 << TIMING_CFG1_WRREC_SHIFT) | \ ( 7 << TIMING_CFG1_REFREC_SHIFT) | \ ( 3 << TIMING_CFG1_ACTTORW_SHIFT) | \ ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \ ( 3 << TIMING_CFG1_PRETOACT_SHIFT)) #define CONFIG_SYS_DDR_TIMING_2 ((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \ (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \ (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \ (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \ (4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \ (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \ (5 << TIMING_CFG2_CPO_SHIFT)) #define CONFIG_SYS_DDR_TIMING_3 0x00000000 /* * The reserved memory */ #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #define CONFIG_SYS_FLASH_BASE 0xF0000000 #define CONFIG_SYS_PIGGY_BASE 0xE8000000 #define CONFIG_SYS_PIGGY_SIZE 128 #define CONFIG_SYS_PAXE_BASE 0xA0000000 #define CONFIG_SYS_PAXE_SIZE 512 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) #define CONFIG_SYS_RAMBOOT #else #undef CONFIG_SYS_RAMBOOT #endif #define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Mon */ /* * Initial RAM Base Address Setup */ #define CONFIG_SYS_INIT_RAM_LOCK 1 #define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */ #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in RAM */ #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) /* * Local Bus Configuration & Clock Setup */ #define CONFIG_SYS_LCRR_DBYP LCRR_DBYP #define CONFIG_SYS_LCRR_EADC LCRR_EADC_2 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 /* * Init Local Bus Memory Controller: * * Bank Bus Machine PortSz Size Device * ---- --- ------- ------ ----- ------ * 0 Local GPCM 16 bit 256MB FLASH * 1 Local GPCM 8 bit 128MB GPIO/PIGGY * 3 Local GPCM 8 bit 512MB PAXE * */ /* * FLASH on the Local Bus */ #define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */ #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ #define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */ #define CONFIG_SYS_FLASH_PROTECTION 1 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */ #define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001b /* 256MB window size */ #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ (2 << BR_PS_SHIFT) | /* 16 bit port size */ \ BR_V) #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \ OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ OR_GPCM_SCY_5 | \ OR_GPCM_TRLX | OR_GPCM_EAD) #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */ #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */ #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } #undef CONFIG_SYS_FLASH_CHECKSUM /* * PRIO1/PIGGY on the local bus CS1 */ #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_PIGGY_BASE /* Window base at flash base */ #define CONFIG_SYS_LBLAWAR1_PRELIM 0x8000001A /* 128MB window size */ #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_PIGGY_BASE | \ (1 << BR_PS_SHIFT) | /* 8 bit port size */ \ BR_V) #define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_PIGGY_SIZE) | /* 128MB */ \ OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ OR_GPCM_SCY_2 | \ OR_GPCM_TRLX | OR_GPCM_EAD) /* * PAXE on the local bus CS3 */ #define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PAXE_BASE /* Window base at flash base */ #define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000001C /* 512MB window size */ #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_PAXE_BASE | \ (1 << BR_PS_SHIFT) | /* 8 bit port size */ \ BR_V) #define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \ OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \ OR_GPCM_SCY_2 | \ OR_GPCM_TRLX | OR_GPCM_EAD) /* * Serial Port */ #define CONFIG_CONS_INDEX 1 #define CONFIG_SYS_NS16550 #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500) #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600) /* Pass open firmware flat tree */ #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 #define CONFIG_OF_STDOUT_VIA_ALIAS /* * General PCI * Addresses are mapped 1-1. */ #undef CONFIG_PCI /* No PCI */ #ifndef CONFIG_NET_MULTI #define CONFIG_NET_MULTI 1 #endif /* * QE UEC ethernet configuration */ #define CONFIG_UEC_ETH #define CONFIG_ETHPRIME "UEC0" #define CONFIG_UEC_ETH1 /* GETH1 */ #define UEC_VERBOSE_DEBUG 1 #ifdef CONFIG_UEC_ETH1 #define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */ #define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */ #define CONFIG_SYS_UEC1_TX_CLK QE_CLK17 #define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH #define CONFIG_SYS_UEC1_PHY_ADDR 0 #define CONFIG_SYS_UEC1_INTERFACE_TYPE RMII #define CONFIG_SYS_UEC1_INTERFACE_SPEED 100 #endif /* * Environment */ #ifndef CONFIG_SYS_RAMBOOT #define CONFIG_ENV_IS_IN_FLASH 1 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ #define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN) /* Address and size of Redundant Environment Sector */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) #else /* CFG_RAMBOOT */ #define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */ #define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 #endif /* CFG_RAMBOOT */ /* I2C */ #define CONFIG_HARD_I2C /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CONFIG_FSL_I2C #define CONFIG_SYS_I2C_SPEED 200000 /* I2C speed and slave address */ #define CONFIG_SYS_I2C_SLAVE 0x7F #define CONFIG_SYS_I2C_OFFSET 0x3000 #define CONFIG_I2C_MULTI_BUS 1 #define CONFIG_I2C_MUX 1 /* EEprom support */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* I2C SYSMON (LM75, AD7414 is almost compatible) */ #define CONFIG_DTT_LM75 1 /* ON Semi's LM75 */ #define CONFIG_DTT_SENSORS {0, 1, 2, 3} /* Sensor addresses */ #define CONFIG_SYS_DTT_MAX_TEMP 70 #define CONFIG_SYS_DTT_LOW_TEMP -30 #define CONFIG_SYS_DTT_HYSTERESIS 3 #define CONFIG_SYS_DTT_BUS_NUM (CONFIG_SYS_MAX_I2C_BUS) #if defined(CONFIG_CMD_NAND) #define CONFIG_NAND_KMETER1 #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE CONFIG_SYS_PIGGY_BASE #endif #if defined(CONFIG_PCI) #define CONFIG_CMD_PCI #endif #if defined(CFG_RAMBOOT) #undef CONFIG_CMD_SAVEENV #undef CONFIG_CMD_LOADS #endif /* * For booting Linux, the board info and command line data * have to be in the first 256 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux */ /* * Core HID Setup */ #define CONFIG_SYS_HID0_INIT 0x000000000 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ HID0_ENABLE_INSTRUCTION_CACHE) #define CONFIG_SYS_HID2 HID2_HBE /* * MMU Setup */ #define CONFIG_HIGH_BATS 1 /* High BATs supported */ /* DDR: cache cacheable */ #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U /* IMMRBAR & PCI IO: cache-inhibit and guarded */ #define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U /* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */ #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE | BATU_BL_128M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT2L (CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U /* FLASH: icache cacheable, but dcache-inhibit and guarded */ #define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U /* Stack in dcache: cacheable, no memory coherence */ #define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10) #define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U /* PAXE: icache cacheable, but dcache-inhibit and guarded */ #define CONFIG_SYS_IBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | BATL_MEMCOHERENCE) #define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE | BATU_BL_256M | BATU_VS | BATU_VP) #define CONFIG_SYS_DBAT5L (CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U #ifdef CONFIG_PCI /* PCI MEM space: cacheable */ #define CFG_IBAT6L (CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE) #define CFG_IBAT6U (CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) #define CFG_DBAT6L CFG_IBAT6L #define CFG_DBAT6U CFG_IBAT6U /* PCI MMIO space: cache-inhibit and guarded */ #define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) #define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP) #define CFG_DBAT7L CFG_IBAT7L #define CFG_DBAT7U CFG_IBAT7U #else /* CONFIG_PCI */ #define CONFIG_SYS_IBAT6L (0) #define CONFIG_SYS_IBAT6U (0) #define CONFIG_SYS_IBAT7L (0) #define CONFIG_SYS_IBAT7U (0) #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U #endif /* CONFIG_PCI */ #define BOOTFLASH_START F0000000 #define CONFIG_PRAM 512 /* protected RAM [KBytes] */ /* * Environment Configuration */ #define CONFIG_ENV_OVERWRITE #ifndef CONFIG_KM_DEF_ENV /* if not set by keymile-common.h */ #define CONFIG_KM_DEF_ENV "km-common=empty\0" #endif #define CONFIG_EXTRA_ENV_SETTINGS \ CONFIG_KM_DEF_ENV \ "rootpath=/opt/eldk/ppc_82xx\0" \ "addcon=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ "ramdisk_file=/tftpboot/kmeter1/uRamdisk\0" \ "loadram=tftp ${ramdisk_addr_r} ${ramdisk_file}\0" \ "loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0" \ "loadkernel=tftp ${kernel_addr_r} ${bootfile}\0" \ "unlock=yes\0" \ "fdt_addr=F0080000\0" \ "kernel_addr=F00a0000\0" \ "ramdisk_addr=F03a0000\0" \ "ramdisk_addr_r=F10000\0" \ "EEprom_ivm=pca9547:70:9\0" \ "dtt_bus=pca9547:70:a\0" \ "mtdids=nor0=app \0" \ "mtdparts=" MK_STR(MTDPARTS_DEFAULT) "\0" \ "" #if defined(CONFIG_UEC_ETH) #define CONFIG_HAS_ETH0 #endif #endif /* __CONFIG_H */