/* * U-Boot - Configuration file for BF537 STAMP board */ #ifndef __CONFIG_BF537_STAMP_H__ #define __CONFIG_BF537_STAMP_H__ #include /* * Processor Settings */ #define CONFIG_BFIN_CPU bf537-0.2 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS /* * Clock Settings * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV */ /* CONFIG_CLKIN_HZ is any value in Hz */ #define CONFIG_CLKIN_HZ 25000000 /* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */ /* 1 = CLKIN / 2 */ #define CONFIG_CLKIN_HALF 0 /* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */ /* 1 = bypass PLL */ #define CONFIG_PLL_BYPASS 0 /* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */ /* Values can range from 0-63 (where 0 means 64) */ #define CONFIG_VCO_MULT 20 /* CCLK_DIV controls the core clock divider */ /* Values can be 1, 2, 4, or 8 ONLY */ #define CONFIG_CCLK_DIV 1 /* SCLK_DIV controls the system clock divider */ /* Values can range from 1-15 */ #define CONFIG_SCLK_DIV 4 /* * Memory Settings */ #define CONFIG_MEM_ADD_WDTH 10 #define CONFIG_MEM_SIZE 64 #define CONFIG_EBIU_SDRRC_VAL 0x306 #define CONFIG_EBIU_SDGCTL_VAL 0x91114d #define CONFIG_EBIU_AMGCTL_VAL 0xFF #define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0 #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) #define CONFIG_SYS_MALLOC_LEN (384 * 1024) /* * Network Settings */ #ifndef __ADSPBF534__ #define ADI_CMDS_NETWORK 1 #define CONFIG_BFIN_MAC #define CONFIG_NETCONSOLE 1 #endif #define CONFIG_HOSTNAME bf537-stamp /* * Flash Settings */ #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_BASE 0x20000000 #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_PROTECTION #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* some have 67 sectors (M29W320DB), but newer have 71 (M29W320EB) */ #define CONFIG_SYS_MAX_FLASH_SECT 71 /* * SPI Settings */ #define CONFIG_BFIN_SPI #define CONFIG_ENV_SPI_MAX_HZ 30000000 #define CONFIG_SF_DEFAULT_SPEED 30000000 #define CONFIG_SPI_FLASH_ALL /* * Env Storage Settings */ #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_OFFSET 0x10000 #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x10000 #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_OFFSET 0x4000 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x2000 #endif #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS) #define ENV_IS_EMBEDDED #else #define CONFIG_ENV_IS_EMBEDDED_IN_LDR #endif #ifdef ENV_IS_EMBEDDED /* WARNING - the following is hand-optimized to fit within * the sector before the environment sector. If it throws * an error during compilation remove an object here to get * it linked after the configuration sector. */ # define LDS_BOARD_TEXT \ arch/blackfin/lib/built-in.o (.text*); \ arch/blackfin/cpu/built-in.o (.text*); \ . = DEFINED(env_offset) ? env_offset : .; \ common/env_embedded.o (.text*); #endif /* * I2C Settings */ #define CONFIG_SYS_I2C #define CONFIG_SYS_I2C_ADI /* * SPI_MMC Settings */ #define CONFIG_MMC_SPI #ifdef CONFIG_MMC_SPI #define CONFIG_MMC #define CONFIG_GENERIC_MMC #endif /* * NAND Settings */ /* #define CONFIG_NAND_PLAT */ #ifdef CONFIG_NAND_PLAT #define CONFIG_SYS_NAND_BASE 0x20212000 #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define BFIN_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 2)) #define BFIN_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 1)) #define BFIN_NAND_WRITE(addr, cmd) \ do { \ bfin_write8(addr, cmd); \ SSYNC(); \ } while (0) #define NAND_PLAT_WRITE_CMD(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_CLE(chip), cmd) #define NAND_PLAT_WRITE_ADR(chip, cmd) BFIN_NAND_WRITE(BFIN_NAND_ALE(chip), cmd) #define NAND_PLAT_GPIO_DEV_READY GPIO_PF3 #endif /* CONFIG_NAND_PLAT */ /* * CF-CARD IDE-HDD Support */ /* * Add CF flash card support in TRUE-IDE Mode (CF-IDE-NAND Card) * Strange address mapping Blackfin A13 connects to CF_A0 */ /* #define CONFIG_BFIN_TRUE_IDE */ /* * Add CF flash card support in Common Memory Mode (CF-IDE-NAND Card) * This should be the preferred mode */ /* #define CONFIG_BFIN_CF_IDE */ /* * Add IDE Disk Drive (HDD) support * See example interface here: * http://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:drivers:ide-blackfin */ /* #define CONFIG_BFIN_HDD_IDE */ #if defined(CONFIG_BFIN_CF_IDE) || \ defined(CONFIG_BFIN_HDD_IDE) || \ defined(CONFIG_BFIN_TRUE_IDE) # define CONFIG_BFIN_IDE 1 # define CONFIG_CMD_IDE #endif #if defined(CONFIG_BFIN_IDE) #define CONFIG_DOS_PARTITION 1 /* * IDE/ATA stuff */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ #define CONFIG_SYS_IDE_MAXBUS 1 #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS * 1) #undef CONFIG_EBIU_AMBCTL1_VAL #define CONFIG_EBIU_AMBCTL1_VAL 0xFFC3FFC3 #define CONFIG_CF_ATASEL_DIS 0x20311800 #define CONFIG_CF_ATASEL_ENA 0x20311802 #if defined(CONFIG_BFIN_TRUE_IDE) /* * Note that these settings aren't for the most part used in include/ata.h * when all of the ATA registers are setup */ #define CONFIG_SYS_ATA_BASE_ADDR 0x2031C000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ #define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A13 */ #elif defined(CONFIG_BFIN_CF_IDE) #define CONFIG_SYS_ATA_BASE_ADDR 0x20211800 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* data I/O */ #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* normal register accesses */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x000E /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 1 /* CF_A0=0, with /CE1 /CE2 odd/even byte selects */ #elif defined(CONFIG_BFIN_HDD_IDE) #define CONFIG_SYS_ATA_BASE_ADDR 0x20314000 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0020 /* data I/O */ #define CONFIG_SYS_ATA_REG_OFFSET 0x0020 /* normal register accesses */ #define CONFIG_SYS_ATA_ALT_OFFSET 0x001C /* alternate registers */ #define CONFIG_SYS_ATA_STRIDE 2 /* CF.A0 --> Blackfin.A1 */ #undef CONFIG_SCLK_DIV #define CONFIG_SCLK_DIV 8 #endif #endif /* * Misc Settings */ #define CONFIG_MISC_INIT_R #define CONFIG_RTC_BFIN #define CONFIG_UART_CONSOLE 0 /* Define if want to do post memory test */ #undef CONFIG_POST #ifdef CONFIG_POST #define CONFIG_SYS_POST_HOTKEYS_GPIO GPIO_PF5 #define CONFIG_POST_BSPEC1_GPIO_LEDS \ GPIO_PF6, GPIO_PF7, GPIO_PF8, GPIO_PF9, GPIO_PF10, GPIO_PF11, #define CONFIG_POST_BSPEC2_GPIO_BUTTONS \ GPIO_PF5, GPIO_PF4, GPIO_PF3, GPIO_PF2, #define CONFIG_POST_BSPEC2_GPIO_NAMES \ 10, 11, 12, 13, #define CONFIG_SYS_POST_FLASH_START 11 #define CONFIG_SYS_POST_FLASH_END 71 #endif /* These are for board tests */ #if 0 #define CONFIG_BOOTCOMMAND "bootldr 0x203f0100" #endif /* * Pull in common ADI header for remaining command/environment setup */ #include #endif