/* * U-boot - Configuration file for BF533 STAMP board */ #ifndef __CONFIG_STAMP_H__ #define __CONFIG_STAMP_H__ #include #define CONFIG_RTC_BFIN 1 #define CONFIG_PANIC_HANG 1 #define CONFIG_BFIN_CPU bf533-0.3 #define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS /* This sets the default state of the cache on U-Boot's boot */ #define CONFIG_ICACHE_ON #define CONFIG_DCACHE_ON /* * Board settings */ #define CONFIG_DRIVER_SMC91111 1 #define CONFIG_SMC91111_BASE 0x20300300 /* FLASH/ETHERNET uses the same address range */ #define SHARED_RESOURCES 1 /* Is I2C bit-banged? */ #define CONFIG_SOFT_I2C 1 /* * Software (bit-bang) I2C driver configuration */ #define PF_SCL PF3 #define PF_SDA PF2 /* * Video splash screen support */ #define CONFIG_VIDEO 0 /* * Clock settings */ /* CONFIG_CLKIN_HZ is any value in Hz */ #define CONFIG_CLKIN_HZ 11059200 /* CONFIG_CLKIN_HALF controls what is passed to PLL 0=CLKIN */ /* 1=CLKIN/2 */ #define CONFIG_CLKIN_HALF 0 /* CONFIG_PLL_BYPASS controls if the PLL is used 0=don't bypass */ /* 1=bypass PLL */ #define CONFIG_PLL_BYPASS 0 /* CONFIG_VCO_MULT controls what the multiplier of the PLL is. */ /* Values can range from 1-64 */ #define CONFIG_VCO_MULT 36 /* CONFIG_CCLK_DIV controls what the core clock divider is */ /* Values can be 1, 2, 4, or 8 ONLY */ #define CONFIG_CCLK_DIV 1 /* CONFIG_SCLK_DIV controls what the peripheral clock divider is*/ /* Values can range from 1-15 */ #define CONFIG_SCLK_DIV 5 /* CONFIG_SPI_BAUD controls the SPI peripheral clock divider */ /* Values can range from 2-65535 */ /* SCK Frequency = SCLK / (2 * CONFIG_SPI_BAUD) */ #define CONFIG_SPI_BAUD 2 #define CONFIG_SPI_BAUD_INITBLOCK 4 /* * Network settings */ #if (CONFIG_DRIVER_SMC91111) #if 0 #define CONFIG_MII #endif /* network support */ #define CONFIG_IPADDR 192.168.0.15 #define CONFIG_NETMASK 255.255.255.0 #define CONFIG_GATEWAYIP 192.168.0.1 #define CONFIG_SERVERIP 192.168.0.2 #define CONFIG_HOSTNAME STAMP #define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs /* To remove hardcoding and enable MAC storage in EEPROM */ /* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */ #endif /* CONFIG_DRIVER_SMC91111 */ /* * Flash settings */ #define CFG_FLASH_CFI /* The flash is CFI compatible */ #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ #define CFG_FLASH_CFI_AMD_RESET #define CFG_FLASH_BASE 0x20000000 #define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 67 /* max number of sectors on one chip */ #if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER) #define CFG_ENV_IS_IN_EEPROM 1 #define CFG_ENV_OFFSET 0x4000 #define CFG_ENV_HEADER (CFG_ENV_OFFSET + 0x12A) /* 0x12A is the length of LDR file header */ #else #define CFG_ENV_IS_IN_FLASH 1 #define CFG_ENV_ADDR 0x20004000 #define CFG_ENV_OFFSET (CFG_ENV_ADDR - CFG_FLASH_BASE) #endif #define CFG_ENV_SIZE 0x2000 #define CFG_ENV_SECT_SIZE 0x2000 /* Total Size of Environment Sector */ #define ENV_IS_EMBEDDED #define CFG_FLASH_ERASE_TOUT 30000 /* Timeout for Chip Erase (in ms) */ #define CFG_FLASH_ERASEBLOCK_TOUT 5000 /* Timeout for Block Erase (in ms) */ #define CFG_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */ /* JFFS Partition offset set */ #define CFG_JFFS2_FIRST_BANK 0 #define CFG_JFFS2_NUM_BANKS 1 /* 512k reserved for u-boot */ #define CFG_JFFS2_FIRST_SECTOR 11 /* * following timeouts shall be used once the * Flash real protection is enabled */ #define CFG_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */ #define CFG_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */ /* * SDRAM settings & memory map */ #define CONFIG_MEM_SIZE 128 /* 128, 64, 32, 16 */ #define CONFIG_MEM_ADD_WDTH 11 /* 8, 9, 10, 11 */ #define CONFIG_MEM_MT48LC64M4A2FB_7E 1 #define CFG_MEMTEST_START 0x00000000 /* memtest works on */ #define CFG_SDRAM_BASE 0x00000000 #define CFG_MAX_RAM_SIZE (CONFIG_MEM_SIZE * 1024 *1024) #define CFG_MEMTEST_END (CFG_MAX_RAM_SIZE - 0x80000 - 1) #define CONFIG_LOADADDR 0x01000000 #define CFG_LOAD_ADDR CONFIG_LOADADDR #define CFG_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ #define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ #define CFG_GBL_DATA_SIZE 0x4000 /* Reserve 16k for Global Data */ #define CONFIG_STACKSIZE (128*1024) /* regular stack */ #define CFG_MONITOR_BASE (CFG_MAX_RAM_SIZE - 0x40000) #define CFG_MALLOC_BASE (CFG_MONITOR_BASE - CFG_MALLOC_LEN) #define CFG_GBL_DATA_ADDR (CFG_MALLOC_BASE - CFG_GBL_DATA_SIZE) #define CONFIG_STACKBASE (CFG_GBL_DATA_ADDR - 4) /* Check to make sure everything fits in SDRAM */ #if ((CFG_MONITOR_BASE + CFG_MONITOR_LEN) > CFG_MAX_RAM_SIZE) #error Memory Map does not fit into configuration #endif #if ( CONFIG_CLKIN_HALF == 0 ) #define CONFIG_VCO_HZ ( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) #else #define CONFIG_VCO_HZ (( CONFIG_CLKIN_HZ * CONFIG_VCO_MULT ) / 2 ) #endif #if (CONFIG_PLL_BYPASS == 0) #define CONFIG_CCLK_HZ ( CONFIG_VCO_HZ / CONFIG_CCLK_DIV ) #define CONFIG_SCLK_HZ ( CONFIG_VCO_HZ / CONFIG_SCLK_DIV ) #else #define CONFIG_CCLK_HZ CONFIG_CLKIN_HZ #define CONFIG_SCLK_HZ CONFIG_CLKIN_HZ #endif /* * Command settings */ #define CFG_LONGHELP 1 #define CONFIG_CMDLINE_EDITING 1 #define CFG_AUTOLOAD "no" /*rarpb, bootp or dhcp commands will perform only a */ /* configuration lookup from the BOOTP/DHCP server, */ /* but not try to load any image using TFTP */ #define CONFIG_BOOTDELAY 5 #define CONFIG_BOOT_RETRY_TIME -1 /* Enable this if bootretry required, currently its disabled */ #define CONFIG_BOOTCOMMAND "run ramboot" #define CONFIG_BOOTARGS "root=/dev/mtdblock0 rw console=ttyBF0,57600" #define CONFIG_EXTRA_ENV_SETTINGS \ "ramargs=setenv bootargs root=/dev/mtdblock0 rw console=ttyBF0,57600\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):" \ "$(rootpath) console=ttyBF0,57600\0" \ "addip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ "$(gatewayip):$(netmask):$(hostname):eth0:off\0" \ "ramboot=tftpboot $(loadaddr) linux; " \ "run ramargs;run addip;bootelf\0" \ "nfsboot=tftpboot $(loadaddr) linux; " \ "run nfsargs;run addip;bootelf\0" \ "flashboot=bootm 0x20100000\0" \ "update=tftpboot $(loadaddr) u-boot.bin; " \ "protect off 0x20000000 0x2003FFFF; erase 0x20000000 0x2003FFFF;" \ "cp.b $(loadaddr) 0x20000000 $(filesize)\0" \ "" #ifdef CONFIG_SOFT_I2C #if (!CONFIG_SOFT_I2C) #undef CONFIG_SOFT_I2C #endif #endif /* * BOOTP options */ #define CONFIG_BOOTP_BOOTFILESIZE #define CONFIG_BOOTP_BOOTPATH #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME /* * Command line configuration. */ #include #define CONFIG_CMD_ELF #define CONFIG_CMD_CACHE #define CONFIG_CMD_JFFS2 #define CONFIG_CMD_EEPROM #define CONFIG_CMD_DATE #if (CONFIG_DRIVER_SMC91111) #define CONFIG_CMD_PING #endif #if (CONFIG_SOFT_I2C) #define CONFIG_CMD_I2C #endif #define CONFIG_CMD_DHCP /* * Console settings */ #define CONFIG_BAUDRATE 57600 #define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } #define CFG_PROMPT "bfin> " /* Monitor Command Prompt */ #if defined(CONFIG_CMD_KGDB) #define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ #else #define CFG_CBSIZE 256 /* Console I/O Buffer Size */ #endif #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ #define CFG_MAXARGS 16 /* max number of command args */ #define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ #define CONFIG_LOADS_ECHO 1 /* * I2C settings * By default PF2 is used as SDA and PF3 as SCL on the Stamp board */ #if (CONFIG_SOFT_I2C) #define I2C_INIT (*pFIO_DIR |= PF_SCL); asm("ssync;") #define I2C_ACTIVE (*pFIO_DIR |= PF_SDA); *pFIO_INEN &= ~PF_SDA; asm("ssync;") #define I2C_TRISTATE (*pFIO_DIR &= ~PF_SDA); *pFIO_INEN |= PF_SDA; asm("ssync;") #define I2C_READ ((volatile)(*pFIO_FLAG_D & PF_SDA) != 0); asm("ssync;") #define I2C_SDA(bit) if(bit) { \ *pFIO_FLAG_S = PF_SDA; \ asm("ssync;"); \ } \ else { \ *pFIO_FLAG_C = PF_SDA; \ asm("ssync;"); \ } #define I2C_SCL(bit) if(bit) { \ *pFIO_FLAG_S = PF_SCL; \ asm("ssync;"); \ } \ else { \ *pFIO_FLAG_C = PF_SCL; \ asm("ssync;"); \ } #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ #define CFG_I2C_SPEED 50000 #define CFG_I2C_SLAVE 0xFE #endif /* CONFIG_SOFT_I2C */ /* * Compact Flash settings */ /* Enabled below option for CF support */ /* #define CONFIG_STAMP_CF 1 */ #if defined(CONFIG_STAMP_CF) && defined(CONFIG_CMD_IDE) #define CONFIG_MISC_INIT_R 1 #define CONFIG_DOS_PARTITION 1 /* * IDE/ATA stuff */ #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */ #undef CONFIG_IDE_LED /* no led for ide supported */ #undef CONFIG_IDE_RESET /* no reset for ide supported */ #define CFG_IDE_MAXBUS 1 /* max. 1 IDE busses */ #define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */ #define CFG_ATA_BASE_ADDR 0x20200000 #define CFG_ATA_IDE0_OFFSET 0x0000 #define CFG_ATA_DATA_OFFSET 0x0020 /* Offset for data I/O */ #define CFG_ATA_REG_OFFSET 0x0020 /* Offset for normal register accesses */ #define CFG_ATA_ALT_OFFSET 0x0007 /* Offset for alternate registers */ #define CFG_ATA_STRIDE 2 #endif /* * Miscellaneous configurable options */ #define CFG_HZ 1000 /* 1ms time tick */ #define CFG_BOOTM_LEN 0x4000000/* Large Image Length, set to 64 Meg */ #define CONFIG_SHOW_BOOT_PROGRESS 1 /* Show boot progress on LEDs */ #define CONFIG_SPI #ifdef CONFIG_VIDEO #if (CONFIG_VIDEO) #define CONFIG_SPLASH_SCREEN 1 #define CONFIG_SILENT_CONSOLE 1 #else #undef CONFIG_VIDEO #endif #endif /* * FLASH organization and environment definitions */ #define CONFIG_EBIU_SDRRC_VAL 0x268 #define CONFIG_EBIU_SDGCTL_VAL 0x911109 #define CONFIG_EBIU_SDBCTL_VAL 0x37 #define CONFIG_EBIU_AMGCTL_VAL 0xFF #define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3 #define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983 #define CF_CONFIG_EBIU_AMBCTL1_VAL 0x99B3ffc2 #include #endif