From 29235b73373f28f2516d2eafbf6ec76ecf8051a3 Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Wed, 5 Feb 2014 20:49:21 -0700 Subject: ARM: rpi_b: convert to use distro defaults Modify the rpi_b board to include the "distro defaults" header, so that all the config options distros expect are enabled. Remove any #defines that enable the same options from the rpi_b.h. Signed-off-by: Stephen Warren --- include/configs/rpi_b.h | 29 +++++++++++++---------------- 1 file changed, 13 insertions(+), 16 deletions(-) (limited to 'include') diff --git a/include/configs/rpi_b.h b/include/configs/rpi_b.h index 976ceaa9c1..202c9c309f 100644 --- a/include/configs/rpi_b.h +++ b/include/configs/rpi_b.h @@ -147,37 +147,34 @@ #define CONFIG_BOOTDELAY 2 /* Shell */ -#define CONFIG_SYS_HUSH_PARSER #define CONFIG_SYS_MAXARGS 8 #define CONFIG_SYS_PROMPT "U-Boot> " -#define CONFIG_SYS_LONGHELP -#define CONFIG_CMDLINE_EDITING #define CONFIG_COMMAND_HISTORY -#define CONFIG_AUTO_COMPLETE /* Commands */ #include -#define CONFIG_CMD_BOOTZ #define CONFIG_CMD_GPIO #define CONFIG_CMD_MMC -#define CONFIG_DOS_PARTITION #define CONFIG_PARTITION_UUIDS #define CONFIG_CMD_PART -#define CONFIG_CMD_FS_GENERIC -#define CONFIG_CMD_FAT -#define CONFIG_CMD_EXT -/* Some things don't make sense on this HW or yet */ -#undef CONFIG_CMD_FPGA -#undef CONFIG_CMD_NET -#undef CONFIG_CMD_NFS -#undef CONFIG_CMD_SAVEENV -/* Device tree support for bootm/bootz */ -#define CONFIG_OF_LIBFDT +/* Device tree support */ #define CONFIG_OF_BOARD_SETUP /* ATAGs support for bootm/bootz */ #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_CMDLINE_TAG #define CONFIG_INITRD_TAG +#include + +/* Some things don't make sense on this HW or yet */ +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS +#undef CONFIG_CMD_SAVEENV +#undef CONFIG_CMD_DHCP +#undef CONFIG_CMD_MII +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_PING + #endif -- cgit v1.2.1 From 5c92d4823d2d5de03ea63cb3fbfc898c39cf199c Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Wed, 5 Feb 2014 20:49:22 -0700 Subject: ARM: rpi_b: load /uEnv.txt from MMC at startup The Pi has no flash to store an environment in the usual fashion. However, the user may wish to customize the environment. We know that the SD card must be present, since that's where the boot ROM has loaded U-Boot from. So, load uEnv.txt from there early during boot. This allows the user to e.g. customize boot_targets, in order to automatically select network boot. Signed-off-by: Stephen Warren --- include/configs/rpi_b.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'include') diff --git a/include/configs/rpi_b.h b/include/configs/rpi_b.h index 202c9c309f..4b5a0c2150 100644 --- a/include/configs/rpi_b.h +++ b/include/configs/rpi_b.h @@ -95,6 +95,11 @@ #define CONFIG_SYS_LOAD_ADDR 0x1000000 #define CONFIG_CONSOLE_MUX #define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_PREBOOT \ + "if load mmc 0:1 ${loadaddr} /uEnv.txt; then " \ + "env import -t ${loadaddr} ${filesize}; " \ + "fi" + /* * Memory layout for where various images get loaded by boot scripts: * -- cgit v1.2.1 From da4105dfcd27c20e5cf4eb750f88938f56620d37 Mon Sep 17 00:00:00 2001 From: Lothar Felten Date: Fri, 31 Jan 2014 17:34:14 +0100 Subject: am335x: Initial support for Silica Pengwyn board This patch add support for the Silica Pengwyn board [1] The board is based on a TI AM3354 CPU [2] All jumpers removed it will boot from the SDcard, the console is on UART1 accessible via the FDTI -> USB. The on board NAND flash is supported and can act as boot medium, depending on jumper settings. USB Host, USB Device and Ethernet are also provided but untested. [1] http://www.silica.com/product/silica-pengwyn-board.html [2] http://www.ti.com/product/am3354 Signed-off-by: Lothar Felten [trini: Move CONFIG_BOARD_LATE_INIT into am335x_evm.h, drop unused spi0_pin_mux from Pengwyn support] Signed-off-by: Tom Rini --- include/configs/am335x_evm.h | 1 + include/configs/pengwyn.h | 208 +++++++++++++++++++++++++++++++++++++ include/configs/ti_am335x_common.h | 1 - 3 files changed, 209 insertions(+), 1 deletion(-) create mode 100644 include/configs/pengwyn.h (limited to 'include') diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 73a9adb293..96ae369c6a 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -20,6 +20,7 @@ #define MACH_TYPE_TIAM335EVM 3589 /* Until the next sync */ #define CONFIG_MACH_TYPE MACH_TYPE_TIAM335EVM +#define CONFIG_BOARD_LATE_INIT /* Clock Defines */ #define V_OSCK 24000000 /* Clock output from T2 */ diff --git a/include/configs/pengwyn.h b/include/configs/pengwyn.h new file mode 100644 index 0000000000..5a555567d0 --- /dev/null +++ b/include/configs/pengwyn.h @@ -0,0 +1,208 @@ +/* + * pengwyn.h + * + * Copyright (C) 2013 Lothar Felten + * + * based on am335x_evm.h, Copyright (C) 2011 Texas Instruments Inc. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_PENGWYN_H +#define __CONFIG_PENGWYN_H + +#define CONFIG_NAND +#define CONFIG_SERIAL1 +#define CONFIG_CONS_INDEX 1 + +#include + +/* Clock Defines */ +#define V_OSCK 24000000 +#define V_SCLK V_OSCK + +/* set env size */ +#define CONFIG_ENV_SIZE 0x4000 + +#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "loadaddr=0x80200000\0" \ + "fdtaddr=0x80F80000\0" \ + "bootpart=0:2\0" \ + "bootdir=/boot\0" \ + "bootfile=zImage\0" \ + "fdtfile=am335x-pengwyn.dtb\0" \ + "console=ttyO0,115200n8\0" \ + "optargs=\0" \ + "mmcdev=0\0" \ + "mmcroot=/dev/mmcblk0p2 ro\0" \ + "mmcrootfstype=ext4 rootwait\0" \ + "rootpath=/export/rootfs\0" \ + "nfsopts=nolock\0" \ + "static_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}" \ + "::off\0" \ + "mmcargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${mmcroot} " \ + "rootfstype=${mmcrootfstype}\0" \ + "netargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ + "ip=dhcp\0" \ + "bootenv=uEnv.txt\0" \ + "loadbootenv=load mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \ + "importbootenv=echo Importing environment from mmc ...; " \ + "env import -t $loadaddr $filesize\0" \ + "loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \ + "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ + "mmcloados=run mmcargs; " \ + "bootz ${loadaddr} - ${fdtaddr};\0" \ + "mmcboot=mmc dev ${mmcdev}; " \ + "if mmc rescan; then " \ + "echo SD/MMC found on device ${mmcdev};" \ + "if run loadbootenv; then " \ + "echo Loaded environment from ${bootenv};" \ + "run importbootenv;" \ + "fi;" \ + "if test -n $uenvcmd; then " \ + "echo Running uenvcmd ...;" \ + "run uenvcmd;" \ + "fi;" \ + "if run loadimage; then " \ + "run loadfdt;" \ + "run mmcloados;" \ + "fi;" \ + "fi;\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload no; " \ + "dhcp; " \ + "tftp ${loadaddr} ${bootfile}; " \ + "tftp ${fdtaddr} ${fdtfile}; " \ + "run netargs; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "nandargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${nandroot} " \ + "rootfstype=${nandrootfstype}\0" \ + "nandroot=ubi0:rootfs rw ubi.mtd=7,2048\0" \ + "nandrootfstype=ubifs rootwait=1\0" \ + "nandboot=echo Booting from nand ...; " \ + "run nandargs; " \ + "nand read ${fdtaddr} u-boot-spl-os; " \ + "nand read ${loadaddr} kernel; " \ + "bootz ${loadaddr} - ${fdtaddr}\0" +#endif + +#define CONFIG_BOOTCOMMAND \ + "run mmcboot;" \ + "run nandboot;" + +/* NS16550 Configuration: primary UART via FDTI */ +#define CONFIG_SYS_NS16550_COM1 0x44e09000 +#define CONFIG_BAUDRATE 115200 + +/* I2C Configuration */ +#define CONFIG_SYS_I2C_SPEED 100000 +#define CONFIG_CMD_EEPROM +#define CONFIG_ENV_EEPROM_IS_ON_I2C +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 +#define CONFIG_SYS_I2C_MULTI_EEPROMS + +/* SPL */ +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_SPL_YMODEM_SUPPORT + +/* General network SPL */ +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT +#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" + +/* NAND support */ +#define CONFIG_CMD_NAND +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_NAND_OMAP_ELM +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 +#define CONFIG_SYS_NAND_ONFI_DETECTION +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +#define GPMC_NAND_ECC_LP_x8_LAYOUT 1 +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:128k(SPL)," \ + "128k(SPL.backup1)," \ + "128k(SPL.backup2)," \ + "128k(SPL.backup3),1792k(u-boot)," \ + "128k(u-boot-spl-os)," \ + "128k(u-boot-env),5m(kernel),-(rootfs)" +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x260000 /* environment starts here */ +#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */ + +/* + * USB configuration. We enable MUSB support, both for host and for + * gadget. We set USB0 as peripheral and USB1 as host, based on the + * board schematic and physical port wired to each. Then for host we + * add mass storage support. + */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_GADGET +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +#define CONFIG_USB_GADGET +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_USB_GADGET_VBUS_DRAW 2 +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_PERIPHERAL +#define CONFIG_AM335X_USB1 +#define CONFIG_AM335X_USB1_MODE MUSB_HOST + +#if defined(CONFIG_MUSB_HOST) +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif + +#if defined(CONFIG_SPL_BUILD) +/* disable host part of MUSB in SPL */ +#undef CONFIG_MUSB_HOST +/* Disable CPSW SPL support so we fit within the 101KiB limit. */ +#undef CONFIG_SPL_ETH_SUPPORT +#endif + +/* Network */ +#define CONFIG_CMD_MII +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 1 +#define CONFIG_PHY_RESET 1 +#define CONFIG_PHY_NATSEMI + +/* CPSW support */ +#define CONFIG_SPL_ETH_SUPPORT + +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#endif /* ! __CONFIG_PENGWYN_H */ diff --git a/include/configs/ti_am335x_common.h b/include/configs/ti_am335x_common.h index 91f97dd061..7e9ca01cd5 100644 --- a/include/configs/ti_am335x_common.h +++ b/include/configs/ti_am335x_common.h @@ -13,7 +13,6 @@ #define __CONFIG_TI_AM335X_COMMON_H__ #define CONFIG_AM33XX -#define CONFIG_BOARD_LATE_INIT #define CONFIG_ARCH_CPU_INIT #define CONFIG_SYS_CACHELINE_SIZE 64 #define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ -- cgit v1.2.1 From 893c04e17cf74db79e052e831fe5de8323cf2aae Mon Sep 17 00:00:00 2001 From: Hannes Petermaier Date: Fri, 7 Feb 2014 08:07:36 +0100 Subject: board: Add support for B&R T-Series Motherboard Adds support for Bernecker & Rainer Industrieelektronik GmbH T-Series Motherboard, using TI's AM3352 SoC. Most of code is derived from TI's AM335x_EVM Signed-off-by: Hannes Petermaier --- include/configs/bur_am335x_common.h | 197 +++++++++++++++++++++++++++ include/configs/tseries.h | 265 ++++++++++++++++++++++++++++++++++++ 2 files changed, 462 insertions(+) create mode 100644 include/configs/bur_am335x_common.h create mode 100644 include/configs/tseries.h (limited to 'include') diff --git a/include/configs/bur_am335x_common.h b/include/configs/bur_am335x_common.h new file mode 100644 index 0000000000..1f57bd2744 --- /dev/null +++ b/include/configs/bur_am335x_common.h @@ -0,0 +1,197 @@ +/* + * bur_am335x_common.h + * + * common parts used by B&R AM335x based boards + * + * Copyright (C) 2013 Hannes Petermaier - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __BUR_AM335X_COMMON_H__ +#define __BUR_AM335X_COMMON_H__ +/* ------------------------------------------------------------------------- */ +#define CONFIG_AM33XX +#define CONFIG_OMAP +#define CONFIG_OMAP_COMMON +#define CONFIG_BOARD_LATE_INIT +#define CONFIG_SYS_CACHELINE_SIZE 64 +#define CONFIG_MAX_RAM_BANK_SIZE (1024 << 20) /* 1GB */ + +/* Timer information */ +#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */ +#define CONFIG_SYS_TIMERBASE 0x48040000 /* Use Timer2 */ + +#define CONFIG_SPL_POWER_SUPPORT +#define CONFIG_POWER_TPS65217 + +#define CONFIG_SYS_NO_FLASH /* have no NOR-flash */ + +#include + +/* NS16550 Configuration */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK 48000000 +#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */ +#define CONFIG_BAUDRATE 115200 + +/* Network defines */ +#define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ +#define CONFIG_CMD_DHCP +#define CONFIG_BOOTP_DNS /* Configurable parts of CMD_DHCP */ +#define CONFIG_BOOTP_SEND_HOSTNAME +#define CONFIG_BOOTP_GATEWAY +#define CONFIG_BOOTP_SUBNETMASK +#define CONFIG_NET_RETRY_COUNT 4 +#define CONFIG_CMD_PING +#define CONFIG_DRIVER_TI_CPSW /* Driver for IP block */ +#define CONFIG_MII /* Required in net/eth.c */ +#define CONFIG_SPL_ETH_SUPPORT +#define CONFIG_PHYLIB +#define CONFIG_PHY_ADDR 1 +#define CONFIG_PHY_NATSEMI +#define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT /* used for a fetching MAC-Address */ +#define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" + +/* + * SPL related defines. The Public RAM memory map the ROM defines the + * area between 0x402F0400 and 0x4030B800 as a download area and + * 0x4030B800 to 0x4030CE00 as a public stack area. The ROM also + * supports X-MODEM loading via UART, and we leverage this and then use + * Y-MODEM to load u-boot.img, when booted over UART. + */ +#define CONFIG_SPL_TEXT_BASE 0x402F0400 +#define CONFIG_SPL_MAX_SIZE (0x4030B800 - CONFIG_SPL_TEXT_BASE) + +/* + * Since SPL did pll and ddr initialization for us, + * we don't need to do it twice. + */ +#if !defined(CONFIG_SPL_BUILD) && !defined(CONFIG_NOR_BOOT) +#define CONFIG_SKIP_LOWLEVEL_INIT +#endif /* !CONFIG_SPL_BUILD, ... */ +/* + * Our DDR memory always starts at 0x80000000 and U-Boot shall have + * relocated itself to higher in memory by the time this value is used. + */ +#define CONFIG_SYS_LOAD_ADDR 0x80000000 +/* + * ---------------------------------------------------------------------------- + * DDR information. We say (for simplicity) that we have 1 bank, + * always, even when we have more. We always start at 0x80000000, + * and we place the initial stack pointer in our SRAM. + */ +#define CONFIG_NR_DRAM_BANKS 1 +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_INIT_SP_ADDR (NON_SECURE_SRAM_END - \ + GENERATED_GBL_DATA_SIZE) + +/* I2C */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_OMAP24_I2C_SPEED 100000 +#define CONFIG_SYS_OMAP24_I2C_SLAVE 1 +#define CONFIG_SYS_I2C_OMAP24XX + +/* GPIO */ +#define CONFIG_OMAP_GPIO +#define CONFIG_CMD_GPIO +/* + * ---------------------------------------------------------------------------- + * The following are general good-enough settings for U-Boot. We set a + * large malloc pool as we generally have a lot of DDR, and we opt for + * function over binary size in the main portion of U-Boot as this is + * generally easily constrained later if needed. We enable the config + * options that give us information in the environment about what board + * we are on so we do not need to rely on the command prompt. We set a + * console baudrate of 115200 and use the default baud rate table. + */ +#define CONFIG_SYS_MALLOC_LEN (1024 << 10) +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "U-Boot (BuR V2.0)# " +#define CONFIG_SYS_CONSOLE_INFO_QUIET +#define CONFIG_ENV_OVERWRITE /* Overwrite ethaddr / serial# */ + +/* As stated above, the following choices are optional. */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_AUTO_COMPLETE +#define CONFIG_CMDLINE_EDITING +#define CONFIG_VERSION_VARIABLE + +/* We set the max number of command args high to avoid HUSH bugs. */ +#define CONFIG_SYS_MAXARGS 64 + +/* Console I/O Buffer Size */ +#define CONFIG_SYS_CBSIZE 512 +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE +\ + sizeof(CONFIG_SYS_PROMPT) + 16) +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +/* + * For commands to use, we take the default list and add a few other + * useful commands. Note that we must have set CONFIG_SYS_NO_FLASH + * prior to this include, in order to skip a few commands. When we do + * have flash, if we expect these commands they must be enabled in that + * config. If desired, a specific list of desired commands can be used + * instead. + */ +#include +/* undefine commands, which we do not need */ +#undef CONFIG_CMD_EDITENV +#undef CONFIG_CMD_FPGA +#undef CONFIG_CMD_IMI +#undef CONFIG_CMD_ITEST +#undef CONFIG_CMD_LOADS +#undef CONFIG_CMD_LOADB +#undef CONFIG_CMD_NFS +#undef CONFIG_CMD_SETGETDCR +#undef CONFIG_CMD_XIMG +#undef CONFIG_CMD_CRC32 +/* define command we need always */ +#define CONFIG_CMD_ECHO +#define CONFIG_CMD_SOURCE + +/* + * Our platforms make use of SPL to initalize the hardware (primarily + * memory) enough for full U-Boot to be loaded. We also support Falcon + * Mode so that the Linux kernel can be booted directly from SPL + * instead, if desired. We make use of the general SPL framework found + * under common/spl/. Given our generally common memory map, we set a + * number of related defaults and sizes here. + */ +#define CONFIG_SPL +#define CONFIG_SPL_FRAMEWORK +/* + * Place the image at the start of the ROM defined image space. + * We limit our size to the ROM-defined downloaded image area, and use the + * rest of the space for stack. We load U-Boot itself into memory at + * 0x80800000 for legacy reasons (to not conflict with older SPLs). We + * have our BSS be placed 1MiB after this, to allow for the default + * Linux kernel address of 0x80008000 to work, in the Falcon Mode case. + * We have the SPL malloc pool at the end of the BSS area. + * + * ---------------------------------------------------------------------------- + */ +#define CONFIG_SPL_STACK CONFIG_SYS_INIT_SP_ADDR +#undef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0x80800000 +#define CONFIG_SPL_BSS_START_ADDR 0x80A00000 +#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */ +#define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ + CONFIG_SPL_BSS_MAX_SIZE) +#define CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_MALLOC_LEN + +/* General parts of the framework, required. */ +#define CONFIG_SPL_I2C_SUPPORT +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_BOARD_INIT +#define CONFIG_SPL_YMODEM_SUPPORT +#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/am33xx/u-boot-spl.lds" + +#endif /* ! __BUR_AM335X_COMMON_H__ */ diff --git a/include/configs/tseries.h b/include/configs/tseries.h new file mode 100644 index 0000000000..8fb87ac441 --- /dev/null +++ b/include/configs/tseries.h @@ -0,0 +1,265 @@ +/* + * tseries.h + * + * specific parts for B&R T-Series Motherboard + * + * Copyright (C) 2013 Hannes Petermaier - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_TSERIES_H__ +#define __CONFIG_TSERIES_H__ + +#include +/* ------------------------------------------------------------------------- */ +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#define CONFIG_POWER_TPS65217 + +/* Support both device trees and ATAGs. */ +#define CONFIG_OF_LIBFDT +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_CMD_BOOTZ +/*#define CONFIG_MACH_TYPE 3589*/ +#define CONFIG_MACH_TYPE 0xFFFFFFFF /* TODO: check with kernel*/ + +/* MMC/SD IP block */ +#if defined(CONFIG_EMMC_BOOT) + #define CONFIG_MMC + #define CONFIG_GENERIC_MMC + #define CONFIG_OMAP_HSMMC + #define CONFIG_CMD_MMC + #define CONFIG_SUPPORT_EMMC_BOOT +/* RAW SD card / eMMC locations. */ + #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */ + #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ + #define CONFIG_SPL_MMC_SUPPORT +#endif /* CONFIG_EMMC_BOOT */ + +/* + * When we have SPI or NAND flash we expect to be making use of mtdparts, + * both for ease of use in U-Boot and for passing information on to + * the Linux kernel. + */ +#if defined(CONFIG_SPI_BOOT) || defined(CONFIG_NAND) +#define CONFIG_MTD_DEVICE /* Required for mtdparts */ +#define CONFIG_CMD_MTDPARTS +#endif /* CONFIG_SPI_BOOT, ... */ + +#undef CONFIG_SPL_OS_BOOT +#ifdef CONFIG_SPL_OS_BOOT +#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000 + +/* RAW SD card / eMMC */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ + +/* NAND */ +#ifdef CONFIG_NAND +#define CONFIG_CMD_SPL_NAND_OFS 0x080000 /* end of u-boot */ +#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x140000 +#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000 +#endif /* CONFIG_NAND */ +#endif /* CONFIG_SPL_OS_BOOT */ + +#ifdef CONFIG_NAND +#define CONFIG_SPL_NAND_AM33XX_BCH /* OMAP4 and later ELM support */ +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_BASE +#define CONFIG_SPL_NAND_DRIVERS +#define CONFIG_SPL_NAND_ECC +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 +#endif /* CONFIG_NAND */ + +/* Always 128 KiB env size */ +#define CONFIG_ENV_SIZE (128 << 10) + +#ifdef CONFIG_NAND +#define NANDARGS \ + "mtdids=" MTDIDS_DEFAULT "\0" \ + "mtdparts=" MTDPARTS_DEFAULT "\0" \ + "nandargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=${nandroot} " \ + "rootfstype=${nandrootfstype}\0" \ + "nandroot=ubi0:rootfs rw ubi.mtd=8,2048\0" \ + "nandrootfstype=ubifs rootwait=1\0" \ + "nandimgsize=0x500000\0" \ + "nandboot=echo Booting from nand ...; " \ + "run nandargs; " \ + "nand read ${loadaddr} kernel ${nandimgsize}; " \ + "bootz ${loadaddr}\0" +#else +#define NANDARGS "" +#endif /* CONFIG_NAND */ + +#ifdef CONFIG_MMC +#define MMCARGS \ + "silent=1\0" +#else +#define MMCARGS "" +#endif /* CONFIG_MMC */ + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=0\0" \ + "loadaddr=0x80200000\0" \ + "bootfile=zImage\0" \ + "console=ttyO0,115200n8\0" \ + "optargs=\0" \ + "rootpath=/tftpboot/tseries/rootfs-small\0" \ + "nfsopts=nolock\0" \ + "netargs=setenv bootargs console=${console} " \ + "${optargs} " \ + "root=/dev/nfs " \ + "nfsroot=${serverip}:${rootpath},${nfsopts} rw " \ + "ip=dhcp\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload no; " \ + "dhcp; " \ + "tftp ${loadaddr} ${bootfile}; " \ + "run netargs; " \ + "bootm ${loadaddr}\0" \ + "usbupdate=echo Updating UBOOT from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 0x80000000 updateubootusb.img; " \ + "source;\0" \ + "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ + "setenv autoload 0; " \ + "dhcp;" \ + "tftp 0x80000000 updateUBOOT.img;" \ + "source;\0" \ + NANDARGS \ + MMCARGS +#endif /* !CONFIG_SPL_BUILD*/ + +#define CONFIG_BOOTCOMMAND \ + "run mmcboot1;" +#define CONFIG_BOOTDELAY 1 /* TODO: für release auf 0 setzen */ + +#ifdef CONFIG_NAND +/* + * GPMC block. We support 1 device and the physical address to + * access CS0 at is 0x8000000. + */ +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x8000000 +#define CONFIG_NAND_OMAP_GPMC +#define CONFIG_CMD_NAND +/* don't change OMAP_ELM, ECCSCHEME. ROM code only supports this */ +#define CONFIG_NAND_OMAP_ELM +#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW +#define GPMC_NAND_ECC_LP_x16_LAYOUT 1 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024) +#define CONFIG_SYS_NAND_PAGE_SIZE 2048 +#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \ + CONFIG_SYS_NAND_PAGE_SIZE) +#define CONFIG_SYS_NAND_OOBSIZE 64 +#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS +#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, \ + 10, 11, 12, 13, 14, 15, 16, 17, \ + 18, 19, 20, 21, 22, 23, 24, 25, \ + 26, 27, 28, 29, 30, 31, 32, 33, \ + 34, 35, 36, 37, 38, 39, 40, 41, \ + 42, 43, 44, 45, 46, 47, 48, 49, \ + 50, 51, 52, 53, 54, 55, 56, 57, } + +#define CONFIG_SYS_NAND_ECCSIZE 512 +#define CONFIG_SYS_NAND_ECCBYTES 14 + +#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000 + +#define MTDIDS_DEFAULT "nand0=omap2-nand.0" +#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \ + "128k(SPL)," \ + "128k(SPL.backup1)," \ + "128k(SPL.backup2)," \ + "128k(SPL.backup3)," \ + "512k(u-boot)," \ + "128k(u-boot-spl-os)," \ + "128k(u-boot-env)," \ + "5m(kernel),"\ + "-(rootfs)" +#endif /* CONFIG_NAND */ + +/* USB configuration */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +/* attention! not only for gadget, enables also highspeed in hostmode */ +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_HOST +#define CONFIG_AM335X_USB1 +#define CONFIG_AM335X_USB1_MODE MUSB_HOST + +#ifdef CONFIG_MUSB_HOST +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif /* CONFIG_MUSB_HOST */ + +#if defined(CONFIG_SPI_BOOT) +/* McSPI IP block */ +#define CONFIG_SPI +#define CONFIG_OMAP3_SPI +#define CONFIG_CMD_SPI +#define CONFIG_CMD_SF +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_STMICRO +#define CONFIG_SF_DEFAULT_SPEED 24000000 + +#define CONFIG_SPL_SPI_SUPPORT +#define CONFIG_SPL_SPI_FLASH_SUPPORT +#define CONFIG_SPL_SPI_LOAD +#define CONFIG_SPL_SPI_BUS 0 +#define CONFIG_SPL_SPI_CS 0 +#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000 +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_SPI_FLASH +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED +#define CONFIG_ENV_SECT_SIZE (4 << 10) /* 4 KB sectors */ +#define CONFIG_ENV_OFFSET (768 << 10) /* 768 KiB in */ +#define CONFIG_ENV_OFFSET_REDUND (896 << 10) /* 896 KiB in */ + +#elif defined(CONFIG_EMMC_BOOT) +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 +#define CONFIG_SYS_MMC_ENV_PART 2 +#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT + +#elif defined(CONFIG_NAND) +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_OFFSET 0x120000 /* TODO: Adresse definieren */ +#define CONFIG_SYS_ENV_SECT_SIZE CONFIG_ENV_SIZE +#else +#error "no storage for Environment defined!" +#endif +/* + * Common filesystems support. When we have removable storage we + * enabled a number of useful commands and support. + */ +#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE +#define CONFIG_CMD_FS_GENERIC +#endif /* CONFIG_MMC, ... */ + +#endif /* ! __CONFIG_TSERIES_H__ */ -- cgit v1.2.1 From 072cefe07d54879816d0f17830f28198af4c2727 Mon Sep 17 00:00:00 2001 From: Hannes Petermaier Date: Fri, 7 Feb 2014 14:06:50 +0100 Subject: Add support for B&R KWB Motherboard Adds support for Bernecker & Rainer Industrieelektronik GmbH KWB Motherboard, using TI's AM3352 SoC. Most of code is derived from TI's AM335x_EVM Signed-off-by: Hannes Petermaier Cc: trini@ti.com --- include/configs/kwb.h | 128 ++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 128 insertions(+) create mode 100644 include/configs/kwb.h (limited to 'include') diff --git a/include/configs/kwb.h b/include/configs/kwb.h new file mode 100644 index 0000000000..0f631c0f60 --- /dev/null +++ b/include/configs/kwb.h @@ -0,0 +1,128 @@ +/* + * kwb.h + * + * specific parts for B&R KWB Motherboard + * + * Copyright (C) 2013 Hannes Petermaier - + * Bernecker & Rainer Industrieelektronik GmbH - http://www.br-automation.com + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __CONFIG_KWB_H__ +#define __CONFIG_KWB_H__ + +#include +/* ------------------------------------------------------------------------- */ +/* Clock Defines */ +#define V_OSCK 26000000 /* Clock output from T2 */ +#define V_SCLK (V_OSCK) + +#define CONFIG_POWER_TPS65217 + +#define CONFIG_MACH_TYPE 3589 +/* I2C IP block */ +#define CONFIG_SYS_OMAP24_I2C_SPEED_PSOC 20000 + +/* GPIO */ +#define CONFIG_SPL_GPIO_SUPPORT + +/* MMC/SD IP block */ +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_OMAP_HSMMC +#define CONFIG_CMD_MMC +#define CONFIG_SUPPORT_EMMC_BOOT +/* RAW SD card / eMMC locations. */ +#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /*addr. 0x60000 */ +#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */ +#define CONFIG_SPL_MMC_SUPPORT + +#undef CONFIG_SPL_OS_BOOT +#ifdef CONFIG_SPL_OS_BOOT +#define CONFIG_SYS_SPL_ARGS_ADDR 0x80F80000 + +/* RAW SD card / eMMC */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900 /* address 0x120000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80 /* address 0x10000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80 /* 64KiB */ + +#endif /* CONFIG_SPL_OS_BOOT */ + +/* Always 128 KiB env size */ +#define CONFIG_ENV_SIZE (128 << 10) + +#ifndef CONFIG_SPL_BUILD +#define CONFIG_EXTRA_ENV_SETTINGS \ + "autoload=0\0" \ + "loadaddr=0x80100000\0" \ + "bootfile=arimg\0" \ + "usbboot=echo Booting from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 ${loadaddr} ${bootfile}; " \ + "usb stop; " \ + "go ${loadaddr};\0" \ + "netboot=echo Booting from network ...; " \ + "setenv autoload 0; " \ + "dhcp; " \ + "tftp ${loadaddr} arimg; " \ + "go ${loadaddr}\0" \ + "usbupdate=echo Updating UBOOT from USB-Stick ...; " \ + "usb start; " \ + "fatload usb 0 0x80000000 updateubootusb.img; " \ + "source;\0" \ + "netupdate=echo Updating UBOOT from Network (TFTP) ...; " \ + "setenv autoload 0; " \ + "dhcp;" \ + "tftp 0x80000000 updateUBOOT.img;" \ + "source;\0" +#endif /* !CONFIG_SPL_BUILD*/ + +#define CONFIG_BOOTCOMMAND \ + "run usbupdate;" +#define CONFIG_BOOTDELAY 1 /* TODO: für release auf 0 setzen */ + +/* undefine command which we not need here */ +#undef CONFIG_BOOTM_LINUX +#undef CONFIG_BOOTM_NETBSD +#undef CONFIG_BOOTM_PLAN9 +#undef CONFIG_BOOTM_RTEMS +#undef CONFIG_GZIP +#undef CONFIG_ZLIB +#undef CONFIG_CMD_CRC32 + +/* USB configuration */ +#define CONFIG_USB_MUSB_DSPS +#define CONFIG_ARCH_MISC_INIT +#define CONFIG_MUSB_PIO_ONLY +#define CONFIG_MUSB_DISABLE_BULK_COMBINE_SPLIT +/* attention! not only for gadget, enables also highspeed in hostmode */ +#define CONFIG_USB_GADGET_DUALSPEED +#define CONFIG_MUSB_HOST +#define CONFIG_AM335X_USB0 +#define CONFIG_AM335X_USB0_MODE MUSB_HOST + +#ifdef CONFIG_MUSB_HOST +#define CONFIG_CMD_USB +#define CONFIG_USB_STORAGE +#endif /* CONFIG_MUSB_HOST */ + +#undef CONFIG_ENV_IS_NOWHERE +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_SYS_MMC_ENV_DEV 1 +#define CONFIG_SYS_MMC_ENV_PART 2 +#define CONFIG_ENV_OFFSET 0x40000 /* TODO: Adresse definieren */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +/* + * Common filesystems support. When we have removable storage we + * enabled a number of useful commands and support. + */ +#if defined(CONFIG_MMC) || defined(CONFIG_USB_STORAGE) +#define CONFIG_DOS_PARTITION +#define CONFIG_CMD_FAT +#define CONFIG_FAT_WRITE +#define CONFIG_CMD_FS_GENERIC +#endif /* CONFIG_MMC, ... */ + +#endif /* ! __CONFIG_TSERIES_H__ */ -- cgit v1.2.1 From 36481ded99a530f6820961a2335e94b485469ae4 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 14 Feb 2014 09:47:17 +0100 Subject: arm: omap3: Fix tao3530/omap3_ha SPL boot hangup (GPIO clocks not enabled) Patch f33b9bd3 [arm: omap3: Enable clocks for peripherals only if they are used] breaks SPL booting on tao3530. Since some gpio input's are read to detect the board revision. But with this patch above, the clocks to the GPIO subsystems are not enabled per default any more. The GPIO banks need to be configured specifically now. Signed-off-by: Stefan Roese Cc: Tom Rini Cc: Michael Trimarchi Reviewed-by: Stefano Babic --- include/configs/tao3530.h | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'include') diff --git a/include/configs/tao3530.h b/include/configs/tao3530.h index 9abfe82902..9c04c23ab7 100644 --- a/include/configs/tao3530.h +++ b/include/configs/tao3530.h @@ -83,6 +83,13 @@ #define CONFIG_OMAP_HSMMC #define CONFIG_DOS_PARTITION +/* GPIO banks */ +#define CONFIG_OMAP3_GPIO_2 /* GPIO32 ..63 is in GPIO bank 2 */ +#define CONFIG_OMAP3_GPIO_3 /* GPIO64 ..95 is in GPIO bank 3 */ +#define CONFIG_OMAP3_GPIO_4 /* GPIO96 ..127 is in GPIO bank 4 */ +#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */ +#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */ + /* commands to include */ #include -- cgit v1.2.1 From 9267110270a4b7b4ccdf9de9d82b7ac85ce57d0c Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Fri, 14 Feb 2014 12:51:25 +0100 Subject: OMAP3: add missing gpio clock init and fix NAND SPL for mcx board Patch contains the same fixes as commit 4b9b2c300a23ca4a85811918dc92e822a9571a87 (missing CONFIG_OMAP3_GPIO_2) and commit f9095aac793aa8917ab9b915c5d449e6dc8d3d30 (missing CONFIG_SPL_NAND_SOFTECC). Same issues are relevant for the mcx board, too. Signed-off-by: Stefano Babic --- include/configs/mcx.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'include') diff --git a/include/configs/mcx.h b/include/configs/mcx.h index dcd29ce7cb..209c2bbd7c 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -98,6 +98,7 @@ /* EHCI */ #define CONFIG_USB_STORAGE +#define CONFIG_OMAP3_GPIO_2 #define CONFIG_OMAP3_GPIO_5 #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_OMAP @@ -395,6 +396,7 @@ #define CONFIG_SYS_NAND_ECCSIZE 256 #define CONFIG_SYS_NAND_ECCBYTES 3 #define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW +#define CONFIG_SPL_NAND_SOFTECC #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE -- cgit v1.2.1 From a5d64dbf20dd4b658dafb081afbbea797b27bdc3 Mon Sep 17 00:00:00 2001 From: Stefano Babic Date: Fri, 14 Feb 2014 12:51:27 +0100 Subject: OMAP3: fix default environment for mcx board Patch allows to load a script at the startup from MMC. Signed-off-by: Stefano Babic --- include/configs/mcx.h | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'include') diff --git a/include/configs/mcx.h b/include/configs/mcx.h index 209c2bbd7c..7c5c2f4d1c 100644 --- a/include/configs/mcx.h +++ b/include/configs/mcx.h @@ -264,10 +264,9 @@ "${mtdparts} " \ "vram=6M omapfb.vram=1:2M,2:2M,3:2M " \ "omapdss.def_disp=lcd;" \ - "bootm 0x82000000 0x84000000\0" - -#define CONFIG_BOOTCOMMAND \ - "run nandboot" + "bootm 0x82000000 0x84000000\0" \ + "bootcmd=mmc rescan;if fatload mmc 0 82000000 loadbootscr.scr;" \ + "then source 82000000;else run nandboot;fi\0" #define CONFIG_AUTO_COMPLETE #define CONFIG_CMDLINE_EDITING -- cgit v1.2.1 From bc97f48915907553f350f843f3a0a6987a008248 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Fri, 21 Feb 2014 09:28:33 +0100 Subject: arm: omap: cm_t35: Remove CONFIG_SYS_BOOTMAPSZ to fix FDT Linux booting With CONFIG_SYS_BOOTMAPSZ defined, recent Linux kernel booting results in this error: Booting using the fdt blob at 0x81f00000 Loading Kernel Image ... OK ERROR: Failed to allocate 0x1189d bytes below 0x80004000. device tree - allocation error FDT creation failed! hanging...### ERROR ### Please RESET the board ### Removing this define solves this issue. Signed-off-by: Stefan Roese Cc: Nikita Kiryanov Cc: Igor Grinberg Cc: Tom Rini --- include/configs/cm_t35.h | 7 ------- 1 file changed, 7 deletions(-) (limited to 'include') diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h index 7729a02ab6..08c67f588c 100644 --- a/include/configs/cm_t35.h +++ b/include/configs/cm_t35.h @@ -45,13 +45,6 @@ #define CONFIG_MISC_INIT_R #define CONFIG_OF_LIBFDT 1 -/* - * The early kernel mapping on ARM currently only maps from the base of DRAM - * to the end of the kernel image. The kernel is loaded at DRAM base + 0x8000. - * The early kernel pagetable uses DRAM base + 0x4000 to DRAM base + 0x8000, - * so that leaves DRAM base to DRAM base + 0x4000 available. - */ -#define CONFIG_SYS_BOOTMAPSZ 0x4000 #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ #define CONFIG_SETUP_MEMORY_TAGS -- cgit v1.2.1 From 01d92b0472647f339fe3dd495c13173ff7e568b4 Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Tue, 21 Jan 2014 17:15:06 -0500 Subject: am335x_evm: Enable GPT commands Signed-off-by: Tom Rini --- include/configs/am335x_evm.h | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'include') diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 96ae369c6a..59a8f36d16 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -32,6 +32,12 @@ /* Always 128 KiB env size */ #define CONFIG_ENV_SIZE (128 << 10) +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + #ifdef CONFIG_NAND #define NANDARGS \ "mtdids=" MTDIDS_DEFAULT "\0" \ @@ -65,6 +71,9 @@ "bootfile=zImage\0" \ "fdtfile=undefined\0" \ "console=ttyO0,115200n8\0" \ + "partitions=" \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \ "optargs=\0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 ro\0" \ @@ -296,6 +305,9 @@ #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_USBETH_SUPPORT) /* disable host part of MUSB in SPL */ #undef CONFIG_MUSB_HOST +/* disable EFI partitions and partition UUID support */ +#undef CONFIG_PARTITION_UUIDS +#undef CONFIG_EFI_PARTITION /* * Disable CPSW SPL support so we fit within the 101KiB limit. */ -- cgit v1.2.1 From 0f1b04439596bc47ea95fab2d7d072b278b2a925 Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Tue, 21 Jan 2014 17:15:07 -0500 Subject: am43xx_evm: Enable GPT commands Signed-off-by: Tom Rini --- include/configs/am43xx_evm.h | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'include') diff --git a/include/configs/am43xx_evm.h b/include/configs/am43xx_evm.h index d3c4756349..9b4716f5aa 100644 --- a/include/configs/am43xx_evm.h +++ b/include/configs/am43xx_evm.h @@ -84,6 +84,12 @@ #define CONFIG_OMAP_USB_PHY #define CONFIG_AM437X_USB2PHY2_HOST +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + #ifndef CONFIG_SPL_BUILD #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x80200000\0" \ @@ -95,6 +101,9 @@ "bootdir=/boot\0" \ "bootfile=zImage\0" \ "console=ttyO0,115200n8\0" \ + "partitions=" \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}\0" \ "optargs=\0" \ "mmcdev=0\0" \ "mmcroot=/dev/mmcblk0p2 rw\0" \ -- cgit v1.2.1 From 2efa79ae00fa935cf336b09ec12188654ae545ce Mon Sep 17 00:00:00 2001 From: Tom Rini Date: Tue, 21 Jan 2014 17:15:08 -0500 Subject: dra7xx_evm: Enable GPT commands Signed-off-by: Tom Rini --- include/configs/dra7xx_evm.h | 11 +++++++++++ 1 file changed, 11 insertions(+) (limited to 'include') diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index 86574c836a..c67cf60c0c 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -34,8 +34,19 @@ #define CONFIG_SYS_OMAP_ABE_SYSCK +/* Define the default GPT table for eMMC */ +#define PARTS_DEFAULT \ + "uuid_disk=${uuid_gpt_disk};" \ + "name=rootfs,start=2MiB,size=-,uuid=${uuid_gpt_rootfs}" + #include +/* Enhance our eMMC support / experience. */ +#define CONFIG_CMD_GPT +#define CONFIG_EFI_PARTITION +#define CONFIG_PARTITION_UUIDS +#define CONFIG_CMD_PART + /* CPSW Ethernet */ #define CONFIG_CMD_NET /* 'bootp' and 'tftp' */ #define CONFIG_CMD_DHCP -- cgit v1.2.1 From 4f80d5ba8e79e4bc96b71295703372718528b3a7 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Tue, 7 Jan 2014 20:06:56 -0600 Subject: omap4_common: config: remove I2C for SPL mode Commit 6789e84ecaa8f45d053084e08c381284a04abff7 (i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework) intended to make I2C driver compatible with latest changes. It unfortunately has had a impact on size on SPL as well. For example on SDP4430, 32032 bytes before/MLO 35416 bytes after/MLO With this mentioned commit, MLO stops booting on SDP4430 as only 32K is accessible for non-secure (bootloader) s/w on GP devices and the size increase to 56K fails boot. On the latest u-boot commit e7be18225fbea76d1f0034b224f0d1e60f07cfcf, MLO is now at size 35592 bytes, However, I2C is not necessary for SPL to function as we use SR_I2C for controlling the PMIC. Disabling I2C reduces MLO to 32224 bytes which allows OMAP4 GP platform to boot up. Since this is common for all OMAP4 platforms, remove the need for I2C for SPL builds in the common config. Signed-off-by: Nishanth Menon Reviewed-by: Sricharan R --- include/configs/ti_omap4_common.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'include') diff --git a/include/configs/ti_omap4_common.h b/include/configs/ti_omap4_common.h index 2f0e4c0f67..bcb5eabd75 100644 --- a/include/configs/ti_omap4_common.h +++ b/include/configs/ti_omap4_common.h @@ -163,4 +163,10 @@ #define CONFIG_SPL_NAND_AM33XX_BCH /* ELM support */ #endif +#ifdef CONFIG_SPL_BUILD +/* No need for i2c in SPL mode as we will use SRI2C for PMIC access on OMAP4 */ +#undef CONFIG_SYS_I2C +#undef CONFIG_SYS_I2C_OMAP24XX +#endif + #endif /* __CONFIG_TI_OMAP4_COMMON_H */ -- cgit v1.2.1 From 1998a1a6c32d5e3ed729e0e08867d6f8fa97df50 Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Thu, 13 Feb 2014 20:44:07 -0700 Subject: ARM: rpi_b: rework boot scripts, enable sysboot Rework rpi_b's bootcmd (and sub-commands) to match Tegra's bootcmd as much as possible. This will aid in a future patch which will create a common header e.g. config_distro_bootcmd.h. While at it, enable booting from extlinux.conf using the sysboot command. The iteration and componentization currently makes a little more sense for Tegra than RPi, but I'd still like to keep the two as similar as possible. USB and networking support is coming to the RPi in due course, and it'll all make more sense then anyway. Signed-off-by: Stephen Warren --- include/configs/rpi_b.h | 85 ++++++++++++++++++++++++++++++++++++++++--------- 1 file changed, 70 insertions(+), 15 deletions(-) (limited to 'include') diff --git a/include/configs/rpi_b.h b/include/configs/rpi_b.h index 4b5a0c2150..6306d61bb2 100644 --- a/include/configs/rpi_b.h +++ b/include/configs/rpi_b.h @@ -100,12 +100,20 @@ "env import -t ${loadaddr} ${filesize}; " \ "fi" +#define ENV_DEVICE_SETTINGS \ + "stdin=serial,lcd\0" \ + "stdout=serial,lcd\0" \ + "stderr=serial,lcd\0" + /* * Memory layout for where various images get loaded by boot scripts: * * scriptaddr can be pretty much anywhere that doesn't conflict with something * else. Put it low in memory to avoid conflicts. * + * pxefile_addr_r can be pretty much anywhere that doesn't conflict with + * something else. Put it low in memory to avoid conflicts. + * * kernel_addr_r must be within the first 128M of RAM in order for the * kernel's CONFIG_AUTO_ZRELADDR option to work. Since the kernel will * decompress itself to 0x8000 after the start of RAM, kernel_addr_r @@ -121,35 +129,82 @@ * ramdisk_addr_r simply shouldn't overlap anything else. Choosing 33M allows * for the FDT/DTB to be up to 1M, which is hopefully plenty. */ -#define CONFIG_EXTRA_ENV_SETTINGS \ - "stdin=serial\0" \ - "stderr=serial,lcd\0" \ - "stdout=serial,lcd\0" \ +#define ENV_MEM_LAYOUT_SETTINGS \ "scriptaddr=0x00000000\0" \ + "pxefile_addr_r=0x00100000\0" \ "kernel_addr_r=0x01000000\0" \ "fdt_addr_r=0x02000000\0" \ "fdtfile=bcm2835-rpi-b.dtb\0" \ "ramdisk_addr_r=0x02100000\0" \ - "boot_targets=mmc0\0" \ - \ - "script_boot=" \ - "if fatload ${devtype} ${devnum}:1 " \ - "${scriptaddr} boot.scr.uimg; then " \ - "source ${scriptaddr}; " \ - "fi;\0" \ - \ + +#define BOOTCMDS_MMC \ "mmc_boot=" \ "setenv devtype mmc; " \ "if mmc dev ${devnum}; then " \ - "run script_boot; " \ + "run scan_boot; " \ "fi\0" \ + "bootcmd_mmc0=setenv devnum 0; run mmc_boot;\0" +#define BOOT_TARGETS_MMC "mmc0" + +#define BOOTCMDS_COMMON \ + "rootpart=1\0" \ + \ + "do_script_boot=" \ + "load ${devtype} ${devnum}:${rootpart} " \ + "${scriptaddr} ${prefix}${script}; " \ + "source ${scriptaddr}\0" \ + \ + "script_boot=" \ + "for script in ${boot_scripts}; do " \ + "if test -e ${devtype} ${devnum}:${rootpart} " \ + "${prefix}${script}; then " \ + "echo Found ${prefix}${script}; " \ + "run do_script_boot; " \ + "echo SCRIPT FAILED: continuing...; " \ + "fi; " \ + "done\0" \ \ - "bootcmd_mmc0=setenv devnum 0; run mmc_boot\0" \ + "do_sysboot_boot=" \ + "sysboot ${devtype} ${devnum}:${rootpart} any " \ + "${scriptaddr} ${prefix}extlinux/extlinux.conf\0" \ + \ + "sysboot_boot=" \ + "if test -e ${devtype} ${devnum}:${rootpart} " \ + "${prefix}extlinux/extlinux.conf; then " \ + "echo Found ${prefix}extlinux/extlinux.conf; " \ + "run do_sysboot_boot; " \ + "echo SCRIPT FAILED: continuing...; " \ + "fi\0" \ + \ + "scan_boot=" \ + "echo Scanning ${devtype} ${devnum}...; " \ + "for prefix in ${boot_prefixes}; do " \ + "run sysboot_boot; " \ + "run script_boot; " \ + "done\0" \ + \ + "boot_targets=" \ + BOOT_TARGETS_MMC " " \ + "\0" \ + \ + "boot_prefixes=/\0" \ + \ + "boot_scripts=boot.scr.uimg\0" \ + \ + BOOTCMDS_MMC #define CONFIG_BOOTCOMMAND \ "for target in ${boot_targets}; do run bootcmd_${target}; done" -#define CONFIG_BOOTDELAY 2 +#define CONFIG_BOOTCOMMAND \ + "for target in ${boot_targets}; do run bootcmd_${target}; done" + +#define CONFIG_EXTRA_ENV_SETTINGS \ + ENV_DEVICE_SETTINGS \ + ENV_MEM_LAYOUT_SETTINGS \ + BOOTCMDS_COMMON + +#define CONFIG_BOOTDELAY 2 /* Shell */ #define CONFIG_SYS_MAXARGS 8 -- cgit v1.2.1 From 989ce049997daefc25c15e1d5bf5307cdca25abb Mon Sep 17 00:00:00 2001 From: Darwin Rambo Date: Tue, 11 Feb 2014 11:06:34 -0800 Subject: arch: bcm281xx: Initial commit of bcm281xx architecture code Add bcm281xx architecture support code including a clock framework and chip reset. Define register block base addresses for the bcm281xx architecture and create an empty gpio header file required when CONFIG_CMD_GPIO is set. Signed-off-by: Darwin Rambo Reviewed-by: Steve Rae Reviewed-by: Tim Kryger --- include/bitfield.h | 58 ++++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 58 insertions(+) create mode 100644 include/bitfield.h (limited to 'include') diff --git a/include/bitfield.h b/include/bitfield.h new file mode 100644 index 0000000000..ec4815c8e0 --- /dev/null +++ b/include/bitfield.h @@ -0,0 +1,58 @@ +/* + * Copyright 2013 Broadcom Corporation. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +/* + * Bitfield operations + * + * These are generic bitfield operations which allow manipulation of variable + * width bitfields within a word. One use of this would be to use data tables + * to determine how to reprogram fields within R/W hardware registers. + * + * Example: + * + * old_reg_val + * +--------+----+---+--+-----+----------+ + * | | | | | old | | + * +--------+----+---+--+-----+----------+ + * + * new_reg_val + * +--------+----+---+--+-----+----------+ + * | | | | | new | | + * +--------+----+---+--+-----+----------+ + * + * mask = bitfield_mask(10, 5); + * old = bitfield_extract(old_reg_val, 10, 5); + * new_reg_val = bitfield_replace(old_reg_val, 10, 5, new); + * + * The numbers 10 and 5 could for example come from data + * tables which describe all bitfields in all registers. + */ + +#include + +/* Produces a mask of set bits covering a range of a uint value */ +static inline uint bitfield_mask(uint shift, uint width) +{ + return ((1 << width) - 1) << shift; +} + +/* Extract the value of a bitfield found within a given register value */ +static inline uint bitfield_extract(uint reg_val, uint shift, uint width) +{ + return (reg_val & bitfield_mask(shift, width)) >> shift; +} + +/* + * Replace the value of a bitfield found within a given register value + * Returns the newly modified uint value with the replaced field. + */ +static inline uint bitfield_replace(uint reg_val, uint shift, uint width, + uint bitfield_val) +{ + uint mask = bitfield_mask(shift, width); + + return (reg_val & ~mask) | (bitfield_val << shift); +} -- cgit v1.2.1 From 9ed679aeeb9899123bf92ed1eafb7cf6965473dc Mon Sep 17 00:00:00 2001 From: Darwin Rambo Date: Tue, 11 Feb 2014 11:06:38 -0800 Subject: board: bcm28155_ap: Add board files Add support for the bcm28155_ap reference board. Signed-off-by: Darwin Rambo Reviewed-by: Steve Rae Reviewed-by: Tim Kryger --- include/configs/bcm28155_ap.h | 140 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 140 insertions(+) create mode 100644 include/configs/bcm28155_ap.h (limited to 'include') diff --git a/include/configs/bcm28155_ap.h b/include/configs/bcm28155_ap.h new file mode 100644 index 0000000000..8e1c81fc13 --- /dev/null +++ b/include/configs/bcm28155_ap.h @@ -0,0 +1,140 @@ +/* + * Copyright 2013 Broadcom Corporation. + * + * SPDX-License-Identifier: GPL-2.0+ + */ + +#ifndef __BCM28155_AP_H +#define __BCM28155_AP_H + +#include +#include + +/* Architecture, CPU, chip, mach, etc */ +#define CONFIG_ARMV7 +#define CONFIG_KONA +#define CONFIG_SKIP_LOWLEVEL_INIT + +/* + * Memory configuration + */ +#define CONFIG_SYS_TEXT_BASE 0xae000000 + +#define CONFIG_SYS_SDRAM_BASE 0x80000000 +#define CONFIG_SYS_SDRAM_SIZE 0x80000000 +#define CONFIG_NR_DRAM_BANKS 1 + +#define CONFIG_SYS_MALLOC_LEN SZ_4M /* see armv7/start.S. */ +#define CONFIG_STACKSIZE SZ_256K + +/* GPIO Driver */ +#define CONFIG_KONA_GPIO + +/* MMC/SD Driver */ +#define CONFIG_SDHCI +#define CONFIG_MMC_SDMA +#define CONFIG_KONA_SDHCI +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC + +#define CONFIG_SYS_SDIO_BASE0 SDIO1_BASE_ADDR +#define CONFIG_SYS_SDIO_BASE1 SDIO2_BASE_ADDR +#define CONFIG_SYS_SDIO_BASE2 SDIO3_BASE_ADDR +#define CONFIG_SYS_SDIO_BASE3 SDIO4_BASE_ADDR +#define CONFIG_SYS_SDIO0_MAX_CLK 48000000 +#define CONFIG_SYS_SDIO1_MAX_CLK 48000000 +#define CONFIG_SYS_SDIO2_MAX_CLK 48000000 +#define CONFIG_SYS_SDIO3_MAX_CLK 48000000 +#define CONFIG_SYS_SDIO0 "sdio1" +#define CONFIG_SYS_SDIO1 "sdio2" +#define CONFIG_SYS_SDIO2 "sdio3" +#define CONFIG_SYS_SDIO3 "sdio4" + +/* I2C Driver */ +#define CONFIG_SYS_I2C +#define CONFIG_SYS_I2C_KONA +#define CONFIG_SYS_SPD_BUS_NUM 3 /* Start with PMU bus */ +#define CONFIG_SYS_MAX_I2C_BUS 4 +#define CONFIG_SYS_I2C_BASE0 BSC1_BASE_ADDR +#define CONFIG_SYS_I2C_BASE1 BSC2_BASE_ADDR +#define CONFIG_SYS_I2C_BASE2 BSC3_BASE_ADDR +#define CONFIG_SYS_I2C_BASE3 PMU_BSC_BASE_ADDR + +/* Timer Driver */ +#define CONFIG_SYS_TIMER_RATE 32000 +#define CONFIG_SYS_TIMER_COUNTER (TIMER_BASE_ADDR + 4) /* STCLO offset */ + +/* Init functions */ +#define CONFIG_MISC_INIT_R /* board's misc_init_r function */ + +/* Some commands use this as the default load address */ +#define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + +/* No mtest functions as recommended */ +#undef CONFIG_CMD_MEMORY + +/* + * This is the initial SP which is used only briefly for relocating the u-boot + * image to the top of SDRAM. After relocation u-boot moves the stack to the + * proper place. + */ +#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE + +/* Serial Info */ +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +/* Post pad 3 bytes after each reg addr */ +#define CONFIG_SYS_NS16550_REG_SIZE (-4) +#define CONFIG_SYS_NS16550_CLK 13000000 +#define CONFIG_CONS_INDEX 1 +#define CONFIG_SYS_NS16550_COM1 0x3e000000 + +#define CONFIG_BAUDRATE 115200 + +#define CONFIG_ENV_SIZE 0x10000 +#define CONFIG_ENV_IS_NOWHERE + +#define CONFIG_SYS_NO_FLASH /* Not using NAND/NOR unmanaged flash */ + +/* console configuration */ +#define CONFIG_SYS_CBSIZE 1024 /* Console buffer size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ + sizeof(CONFIG_SYS_PROMPT) + 16) /* Printbuffer size */ +#define CONFIG_SYS_MAXARGS 64 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +/* + * One partition type must be defined for part.c + * This is necessary for the fatls command to work on an SD card + * for example. + */ +#define CONFIG_DOS_PARTITION + +/* version string, parser, etc */ +#define CONFIG_VERSION_VARIABLE +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_CMDLINE_EDITING +#define CONFIG_SYS_LONGHELP + +#define CONFIG_CRC32_VERIFY +#define CONFIG_MX_CYCLIC + +/* Initial upstream - boot to cmd prompt only */ +#define CONFIG_BOOTCOMMAND "" + +/* Commands */ +#include +#define CONFIG_CMD_ASKENV +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_FAT +#define CONFIG_CMD_GPIO +#define CONFIG_CMD_I2C +#define CONFIG_CMD_MMC +#define CONFIG_CMD_BOOTZ +#define CONFIG_FAT_WRITE + +#undef CONFIG_CMD_NET +#undef CONFIG_CMD_NFS + +#endif /* __BCM28155_AP_H */ -- cgit v1.2.1 From b60eff31f3bd71a6f14b6c6efc8ad5fb3705de6d Mon Sep 17 00:00:00 2001 From: Albert ARIBAUD Date: Sat, 22 Feb 2014 17:53:43 +0100 Subject: arm: remove unneeded symbol offsets and _TEXT_BASE Remove the last uses of symbol offsets in ARM U-Boot. Remove some needless uses of _TEXT_BASE. Remove all _TEXT_BASE definitions. Signed-off-by: Albert ARIBAUD --- include/asm-generic/sections.h | 26 +++++++------------------- 1 file changed, 7 insertions(+), 19 deletions(-) (limited to 'include') diff --git a/include/asm-generic/sections.h b/include/asm-generic/sections.h index 7e1eb4bf5e..458952fb58 100644 --- a/include/asm-generic/sections.h +++ b/include/asm-generic/sections.h @@ -63,28 +63,16 @@ extern char __image_copy_end[]; extern void _start(void); /* - * ARM needs to use offsets for symbols, since the values of some symbols - * are not resolved prior to relocation (and are just 0). Maybe this can be - * resolved, or maybe other architectures are similar, iwc this should be - * promoted to an architecture option. + * ARM defines its symbols as char[]. Other arches define them as ulongs. */ #ifdef CONFIG_ARM -#define CONFIG_SYS_SYM_OFFSETS -#endif - -#ifdef CONFIG_SYS_SYM_OFFSETS -/* Start/end of the relocation entries, as an offset from _start */ -extern ulong _rel_dyn_start_ofs; -extern ulong _rel_dyn_end_ofs; - -/* End of the region to be relocated, as an offset form _start */ -extern ulong _image_copy_end_ofs; -extern ulong _bss_start_ofs; /* BSS start relative to _start */ -extern ulong _bss_end_ofs; /* BSS end relative to _start */ -extern ulong _end_ofs; /* end of image relative to _start */ - -extern ulong _TEXT_BASE; /* code start */ +extern char __bss_start[]; +extern char __bss_end[]; +extern char __image_copy_start[]; +extern char __image_copy_end[]; +extern char __rel_dyn_start[]; +extern char __rel_dyn_end[]; #else /* don't use offsets: */ -- cgit v1.2.1