From 02a9ce7187bae8f4dafcc8201d85e12d073f8151 Mon Sep 17 00:00:00 2001 From: James Yang Date: Fri, 4 Jan 2013 08:14:03 +0000 Subject: README.fsl-ddr typos and update to reflect hotkey Documentation fix to README.fsl-ddr to fix typos and to reflect use of 'd' hotkey to enter the FSL DDR debugger. Signed-off-by: James Yang Signed-off-by: Andy Fleming --- doc/README.fsl-ddr | 35 +++++++++++++++++++++-------------- 1 file changed, 21 insertions(+), 14 deletions(-) (limited to 'doc/README.fsl-ddr') diff --git a/doc/README.fsl-ddr b/doc/README.fsl-ddr index b2a7c0fab4..1243a12227 100644 --- a/doc/README.fsl-ddr +++ b/doc/README.fsl-ddr @@ -263,17 +263,21 @@ Reference http://www.samsung.com/global/business/semiconductor/products/dram/dow Interactive DDR debugging =========================== -For DDR parameter tuning up and debugging, the interactive DDR debugging can -be activated by saving an environment variable "ddr_interactive". The value -doesn't matter. Once activated, U-boot prompts "FSL DDR>" before enabling DDR -controller. The available commands can be seen by typing "help". - -Another way to enter debug mode without using environment variable is to send -a key press during boot, like one would do to abort auto boot. To save booting -time, no additioal delay is added so the window to send the key press is very -short. For example, user can send the key press using reset command followed by -hitting enter key twice. In case of power on reset, user can keep hitting any -key while applying the power. +For DDR parameter tuning up and debugging, the interactive DDR debugger can +be activated by setting the environment variable "ddr_interactive" to any +value. (The value of ddr_interactive may have a meaning in the future, but, +for now, the presence of the variable will cause the debugger to run.) Once +activated, U-boot will show the prompt "FSL DDR>" before enabling the DDR +controller. The available commands are printed by typing "help". + +Another way to enter the interactive DDR debugger without setting the +environment variable is to send the 'd' character early during the boot +process. To save booting time, no additional delay is added, so the window +to send the key press is very short -- basically, it is the time before the +memory controller code starts to run. For example, when rebooting from +within u-boot, the user must press 'd' IMMEDIATELY after hitting enter to +initiate a 'reset' command. In case of power on/reset, the user can hold +down the 'd' key while applying power or hitting the board's reset button. The example flow of using interactive debugging is type command "compute" to calculate the parameters from the default @@ -281,13 +285,16 @@ type command "print" with arguments to show SPD, options, registers type command "edit" with arguments to change any if desired type command "copy" with arguments to copy controller/dimm settings type command "go" to continue calculation and enable DDR controller + +Additional commands to restart the debugging are: type command "reset" to reset the board type command "recompute" to reload SPD and start over Note, check "next_step" to show the flow. For example, after edit opts, the next_step is STEP_ASSIGN_ADDRESSES. After editing registers, the next_step is -STEP_PROGRAM_REGS. Upon issuing command "go", DDR controller will be enabled -with current setting without further calculation. +STEP_PROGRAM_REGS. Upon issuing command "go", the debugger will program the +DDR controller with the current setting without further calculation and then +exit to resume the booting of the machine. The detail syntax for each commands are @@ -340,7 +347,7 @@ Examples of debugging flow FSL DDR>compute Detected UDIMM UG51U6400N8SU-ACF - SL DDR>print + FSL DDR>print print [c] [d] [spd] [dimmparms] [commonparms] [opts] [addresses] [regs] FSL DDR>print dimmparms DIMM parameters: Controller=0 DIMM=0 -- cgit v1.2.1