From 813fcb8a7ed53933613b38ed6db93f6319c01927 Mon Sep 17 00:00:00 2001 From: Doug Anderson Date: Mon, 13 Feb 2012 07:38:05 +0000 Subject: EXYNOS: SMDK5250: Support all 4 UARTs This properly configures the mux to enable all UARTs. This also fixes things so that we don't configure balls XUCTSN_1 and XURTSN_1 as UART1 configuration (RTS/CTS), since they aren't connected. Signed-off-by: Doug Anderson Acked-by: Chander kashyap Signed-off-by: Minkyu Kang --- board/samsung/smdk5250/smdk5250.c | 44 +++++++++++++++++++++++++++++++++++++-- 1 file changed, 42 insertions(+), 2 deletions(-) (limited to 'board') diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c index 928c08f9b5..32786e228f 100644 --- a/board/samsung/smdk5250/smdk5250.c +++ b/board/samsung/smdk5250/smdk5250.c @@ -224,11 +224,51 @@ static void board_uart_init(void) (struct exynos5_gpio_part1 *) samsung_get_base_gpio_part1(); int i; - /* UART1 GPIOs (part1) : GPA0CON[7:4] 0x2222 */ - for (i = 4; i < 8; i++) { + /* + * UART0 GPIOs : GPA0CON[3:0] 0x2222 + * Must set CFG17 switches to select UART0 to use. + */ + for (i = 0; i <= 3; i++) { s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); } + + /* + * UART1 GPIOs : GPA0CON[5:4] 0x22 + * Must set CFG17 switches to select UART1 to use. + * + * This only sets RXD/TXD, as RTS/CTS need a resistor soldered down + * in order to use them (so that those pins can be used for I2C). + */ + for (i = 4; i <= 5; i++) { + s5p_gpio_set_pull(&gpio1->a0, i, GPIO_PULL_NONE); + s5p_gpio_cfg_pin(&gpio1->a0, i, GPIO_FUNC(0x2)); + } + + /* + * UART2 GPIOs : GPA1CON[1:0] 0x22 + * Must set CFG17 switches to select UART2 to use. + * + * This only sets RXD/TXD, as RTS/CTS need a resistor soldered down + * in order to use them (so that those pins can be used for I2C). + */ + for (i = 0; i <= 1; i++) { + s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); + s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); + } + + /* + * UART3 GPIOs : GPA1CON[5:4] 0x22 + * Must set CFG16 switches to select UART3 to use. + */ + for (i = 4; i <= 5; i++) { + s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); + s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC(0x2)); + } + + /* + * There's no mux for UART4--it's internal only + */ } #ifdef CONFIG_BOARD_EARLY_INIT_F -- cgit v1.2.1