From 58cc97877713f46d2e7dfd515844c29c70c56d82 Mon Sep 17 00:00:00 2001
From: Pardeep Kumar Singla <b45784@freescale.com>
Date: Thu, 25 Jul 2013 12:12:14 -0500
Subject: mx6qsabresd: Add splash screen support via HDMI

Signed-off-by: Pardeep Kumar Singla <b45784@freescale.com>
---
 board/freescale/mx6sabresd/mx6sabresd.c | 64 ++++++++++++++++++++++++++++++++-
 1 file changed, 63 insertions(+), 1 deletion(-)

(limited to 'board')

diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 222ee98c0d..4694b5cba5 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -29,7 +29,12 @@
 #include <fsl_esdhc.h>
 #include <miiphy.h>
 #include <netdev.h>
-
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <linux/fb.h>
+#include <ipu_pixfmt.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
 DECLARE_GLOBAL_DATA_PTR;
 
 #define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
@@ -239,6 +244,60 @@ int board_phy_config(struct phy_device *phydev)
 	return 0;
 }
 
+#if defined(CONFIG_VIDEO_IPUV3)
+static struct fb_videomode const hdmi = {
+	.name           = "HDMI",
+	.refresh        = 60,
+	.xres           = 1024,
+	.yres           = 768,
+	.pixclock       = 15385,
+	.left_margin    = 220,
+	.right_margin   = 40,
+	.upper_margin   = 21,
+	.lower_margin   = 7,
+	.hsync_len      = 60,
+	.vsync_len      = 10,
+	.sync           = FB_SYNC_EXT,
+	.vmode          = FB_VMODE_NONINTERLACED
+};
+
+int board_video_skip(void)
+{
+	int ret;
+
+	ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24);
+
+	if (ret)
+		printf("HDMI cannot be configured: %d\n", ret);
+
+	imx_enable_hdmi_phy();
+	return ret;
+}
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+
+	reg = readl(&mxc_ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->chsccdr);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
 int board_eth_init(bd_t *bis)
 {
 	int ret;
@@ -255,6 +314,9 @@ int board_eth_init(bd_t *bis)
 int board_early_init_f(void)
 {
 	setup_iomux_uart();
+#if defined(CONFIG_VIDEO_IPUV3)
+	setup_display();
+#endif
 
 	return 0;
 }
-- 
cgit v1.2.1