From 601fbec7cf815bc2b26ba2546ac5e8501fc7edae Mon Sep 17 00:00:00 2001 From: Masahiro Yamada Date: Fri, 20 Feb 2015 17:04:05 +0900 Subject: ARM: davinci: move SoC sources to mach-davinci Move arch/arm/cpu/arm926ejs/davinci/* -> arch/arm/mach-davinci/* Signed-off-by: Masahiro Yamada Cc: Tom Rini --- arch/arm/cpu/arm926ejs/Makefile | 1 - arch/arm/cpu/arm926ejs/davinci/Kconfig | 78 --- arch/arm/cpu/arm926ejs/davinci/Makefile | 28 - arch/arm/cpu/arm926ejs/davinci/config.mk | 8 - arch/arm/cpu/arm926ejs/davinci/cpu.c | 223 -------- arch/arm/cpu/arm926ejs/davinci/da830_pinmux.c | 139 ----- arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c | 313 ----------- arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c | 181 ------- arch/arm/cpu/arm926ejs/davinci/dm355.c | 30 - arch/arm/cpu/arm926ejs/davinci/dm365.c | 20 - arch/arm/cpu/arm926ejs/davinci/dm365_lowlevel.c | 460 ---------------- arch/arm/cpu/arm926ejs/davinci/dm644x.c | 81 --- arch/arm/cpu/arm926ejs/davinci/dm646x.c | 26 - arch/arm/cpu/arm926ejs/davinci/dp83848.c | 128 ----- arch/arm/cpu/arm926ejs/davinci/et1011c.c | 42 -- arch/arm/cpu/arm926ejs/davinci/ksz8873.c | 53 -- arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S | 693 ------------------------ arch/arm/cpu/arm926ejs/davinci/lxt972.c | 113 ---- arch/arm/cpu/arm926ejs/davinci/misc.c | 138 ----- arch/arm/cpu/arm926ejs/davinci/pinmux.c | 90 --- arch/arm/cpu/arm926ejs/davinci/psc.c | 160 ------ arch/arm/cpu/arm926ejs/davinci/reset.c | 32 -- arch/arm/cpu/arm926ejs/davinci/spl.c | 65 --- arch/arm/cpu/arm926ejs/davinci/timer.c | 128 ----- 24 files changed, 3230 deletions(-) delete mode 100644 arch/arm/cpu/arm926ejs/davinci/Kconfig delete mode 100644 arch/arm/cpu/arm926ejs/davinci/Makefile delete mode 100644 arch/arm/cpu/arm926ejs/davinci/config.mk delete mode 100644 arch/arm/cpu/arm926ejs/davinci/cpu.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/da830_pinmux.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/dm355.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/dm365.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/dm365_lowlevel.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/dm644x.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/dm646x.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/dp83848.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/et1011c.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/ksz8873.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S delete mode 100644 arch/arm/cpu/arm926ejs/davinci/lxt972.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/misc.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/pinmux.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/psc.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/reset.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/spl.c delete mode 100644 arch/arm/cpu/arm926ejs/davinci/timer.c (limited to 'arch/arm/cpu') diff --git a/arch/arm/cpu/arm926ejs/Makefile b/arch/arm/cpu/arm926ejs/Makefile index f41357aaeb..27b4353a9d 100644 --- a/arch/arm/cpu/arm926ejs/Makefile +++ b/arch/arm/cpu/arm926ejs/Makefile @@ -15,7 +15,6 @@ endif endif obj-$(CONFIG_ARMADA100) += armada100/ -obj-$(CONFIG_ARCH_DAVINCI) += davinci/ obj-$(CONFIG_KIRKWOOD) += kirkwood/ obj-$(if $(filter lpc32xx,$(SOC)),y) += lpc32xx/ obj-$(CONFIG_MB86R0x) += mb86r0x/ diff --git a/arch/arm/cpu/arm926ejs/davinci/Kconfig b/arch/arm/cpu/arm926ejs/davinci/Kconfig deleted file mode 100644 index 613f04d8b0..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/Kconfig +++ /dev/null @@ -1,78 +0,0 @@ -if ARCH_DAVINCI - -choice - prompt "DaVinci board select" - -config TARGET_ENBW_CMC - bool "EnBW CMC board" - -config TARGET_IPAM390 - bool "IPAM390 board" - select SUPPORT_SPL - -config TARGET_DA830EVM - bool "DA830 EVM board" - -config TARGET_DA850EVM - bool "DA850 EVM board" - select SUPPORT_SPL - -config TARGET_CAM_ENC_4XX - bool "CAM ENC 4xx board" - select SUPPORT_SPL - -config TARGET_HAWKBOARD - bool "Hawkboard" - select SUPPORT_SPL - -config TARGET_DAVINCI_DM355EVM - bool "DM355 EVM board" - -config TARGET_DAVINCI_DM355LEOPARD - bool "DM355 Leopard board" - -config TARGET_DAVINCI_DM365EVM - bool "DM365 EVM board" - -config TARGET_DAVINCI_DM6467EVM - bool "DM6467 EVM board" - -config TARGET_DAVINCI_DVEVM - bool "DVEVM board" - -config TARGET_EA20 - bool "EA20 board" - -config TARGET_DAVINCI_SCHMOOGIE - bool "Schmoogie board" - -config TARGET_DAVINCI_SFFSDR - bool "SFFSDR board" - -config TARGET_DAVINCI_SONATA - bool "Sonata board" - -config TARGET_CALIMAIN - bool "Calimain board" - -endchoice - -config SYS_SOC - default "davinci" - -source "board/enbw/enbw_cmc/Kconfig" -source "board/ait/cam_enc_4xx/Kconfig" -source "board/Barix/ipam390/Kconfig" -source "board/davinci/da8xxevm/Kconfig" -source "board/davinci/dm355evm/Kconfig" -source "board/davinci/dm355leopard/Kconfig" -source "board/davinci/dm365evm/Kconfig" -source "board/davinci/dm6467evm/Kconfig" -source "board/davinci/dvevm/Kconfig" -source "board/davinci/ea20/Kconfig" -source "board/davinci/schmoogie/Kconfig" -source "board/davinci/sffsdr/Kconfig" -source "board/davinci/sonata/Kconfig" -source "board/omicron/calimain/Kconfig" - -endif diff --git a/arch/arm/cpu/arm926ejs/davinci/Makefile b/arch/arm/cpu/arm926ejs/davinci/Makefile deleted file mode 100644 index 7d67191de8..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/Makefile +++ /dev/null @@ -1,28 +0,0 @@ -# -# (C) Copyright 2000-2006 -# Wolfgang Denk, DENX Software Engineering, wd@denx.de. -# -# Copyright (C) 2007 Sergey Kubushyn -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y += cpu.o misc.o timer.o psc.o pinmux.o reset.o -obj-$(CONFIG_DA850_LOWLEVEL) += da850_lowlevel.o -obj-$(CONFIG_SOC_DM355) += dm355.o -obj-$(CONFIG_SOC_DM365) += dm365.o -obj-$(CONFIG_SOC_DM644X) += dm644x.o -obj-$(CONFIG_SOC_DM646X) += dm646x.o -obj-$(CONFIG_SOC_DA830) += da830_pinmux.o -obj-$(CONFIG_SOC_DA850) += da850_pinmux.o -obj-$(CONFIG_DRIVER_TI_EMAC) += lxt972.o dp83848.o et1011c.o ksz8873.o - -ifdef CONFIG_SPL_BUILD -obj-$(CONFIG_SPL_FRAMEWORK) += spl.o -obj-$(CONFIG_SOC_DM365) += dm365_lowlevel.o -obj-$(CONFIG_SOC_DA8XX) += da850_lowlevel.o -endif - -ifndef CONFIG_SKIP_LOWLEVEL_INIT -obj-y += lowlevel_init.o -endif diff --git a/arch/arm/cpu/arm926ejs/davinci/config.mk b/arch/arm/cpu/arm926ejs/davinci/config.mk deleted file mode 100644 index 69e9d5ab21..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/config.mk +++ /dev/null @@ -1,8 +0,0 @@ -# -# Copyright (C) 2012, Texas Instruments, Incorporated - http://www.ti.com/ -# -# SPDX-License-Identifier: GPL-2.0+ -# -ifndef CONFIG_SPL_BUILD -ALL-$(CONFIG_SPL_FRAMEWORK) += u-boot.ais -endif diff --git a/arch/arm/cpu/arm926ejs/davinci/cpu.c b/arch/arm/cpu/arm926ejs/davinci/cpu.c deleted file mode 100644 index ff61147757..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/cpu.c +++ /dev/null @@ -1,223 +0,0 @@ -/* - * Copyright (C) 2004 Texas Instruments. - * Copyright (C) 2009 David Brownell - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -/* offsets from PLL controller base */ -#define PLLC_PLLCTL 0x100 -#define PLLC_PLLM 0x110 -#define PLLC_PREDIV 0x114 -#define PLLC_PLLDIV1 0x118 -#define PLLC_PLLDIV2 0x11c -#define PLLC_PLLDIV3 0x120 -#define PLLC_POSTDIV 0x128 -#define PLLC_BPDIV 0x12c -#define PLLC_PLLDIV4 0x160 -#define PLLC_PLLDIV5 0x164 -#define PLLC_PLLDIV6 0x168 -#define PLLC_PLLDIV7 0x16c -#define PLLC_PLLDIV8 0x170 -#define PLLC_PLLDIV9 0x174 - -#define BIT(x) (1 << (x)) - -/* SOC-specific pll info */ -#ifdef CONFIG_SOC_DM355 -#define ARM_PLLDIV PLLC_PLLDIV1 -#define DDR_PLLDIV PLLC_PLLDIV1 -#endif - -#ifdef CONFIG_SOC_DM644X -#define ARM_PLLDIV PLLC_PLLDIV2 -#define DSP_PLLDIV PLLC_PLLDIV1 -#define DDR_PLLDIV PLLC_PLLDIV2 -#endif - -#ifdef CONFIG_SOC_DM646X -#define DSP_PLLDIV PLLC_PLLDIV1 -#define ARM_PLLDIV PLLC_PLLDIV2 -#define DDR_PLLDIV PLLC_PLLDIV1 -#endif - -#ifdef CONFIG_SOC_DA8XX -unsigned int sysdiv[9] = { - PLLC_PLLDIV1, PLLC_PLLDIV2, PLLC_PLLDIV3, PLLC_PLLDIV4, PLLC_PLLDIV5, - PLLC_PLLDIV6, PLLC_PLLDIV7, PLLC_PLLDIV8, PLLC_PLLDIV9 -}; - -int clk_get(enum davinci_clk_ids id) -{ - int pre_div; - int pllm; - int post_div; - int pll_out; - unsigned int pll_base; - - pll_out = CONFIG_SYS_OSCIN_FREQ; - - if (id == DAVINCI_AUXCLK_CLKID) - goto out; - - if ((id >> 16) == 1) - pll_base = (unsigned int)davinci_pllc1_regs; - else - pll_base = (unsigned int)davinci_pllc0_regs; - - id &= 0xFFFF; - - /* - * Lets keep this simple. Combining operations can result in - * unexpected approximations - */ - pre_div = (readl(pll_base + PLLC_PREDIV) & - DAVINCI_PLLC_DIV_MASK) + 1; - pllm = readl(pll_base + PLLC_PLLM) + 1; - - pll_out /= pre_div; - pll_out *= pllm; - - if (id == DAVINCI_PLLM_CLKID) - goto out; - - post_div = (readl(pll_base + PLLC_POSTDIV) & - DAVINCI_PLLC_DIV_MASK) + 1; - - pll_out /= post_div; - - if (id == DAVINCI_PLLC_CLKID) - goto out; - - pll_out /= (readl(pll_base + sysdiv[id - 1]) & - DAVINCI_PLLC_DIV_MASK) + 1; - -out: - return pll_out; -} - -int set_cpu_clk_info(void) -{ - gd->bd->bi_arm_freq = clk_get(DAVINCI_ARM_CLKID) / 1000000; - /* DDR PHY uses an x2 input clock */ - gd->bd->bi_ddr_freq = cpu_is_da830() ? 0 : - (clk_get(DAVINCI_DDR_CLKID) / 1000000); - gd->bd->bi_dsp_freq = 0; - return 0; -} - -#else /* CONFIG_SOC_DA8XX */ - -static unsigned pll_div(volatile void *pllbase, unsigned offset) -{ - u32 div; - - div = REG(pllbase + offset); - return (div & BIT(15)) ? (1 + (div & 0x1f)) : 1; -} - -static inline unsigned pll_prediv(volatile void *pllbase) -{ -#ifdef CONFIG_SOC_DM355 - /* this register read seems to fail on pll0 */ - if (pllbase == (volatile void *)DAVINCI_PLL_CNTRL0_BASE) - return 8; - else - return pll_div(pllbase, PLLC_PREDIV); -#elif defined(CONFIG_SOC_DM365) - return pll_div(pllbase, PLLC_PREDIV); -#endif - return 1; -} - -static inline unsigned pll_postdiv(volatile void *pllbase) -{ -#if defined(CONFIG_SOC_DM355) || defined(CONFIG_SOC_DM365) - return pll_div(pllbase, PLLC_POSTDIV); -#elif defined(CONFIG_SOC_DM6446) - if (pllbase == (volatile void *)DAVINCI_PLL_CNTRL0_BASE) - return pll_div(pllbase, PLLC_POSTDIV); -#endif - return 1; -} - -static unsigned pll_sysclk_mhz(unsigned pll_addr, unsigned div) -{ - volatile void *pllbase = (volatile void *) pll_addr; -#ifdef CONFIG_SOC_DM646X - unsigned base = CONFIG_REFCLK_FREQ / 1000; -#else - unsigned base = CONFIG_SYS_HZ_CLOCK / 1000; -#endif - - /* the PLL might be bypassed */ - if (readl(pllbase + PLLC_PLLCTL) & BIT(0)) { - base /= pll_prediv(pllbase); -#if defined(CONFIG_SOC_DM365) - base *= 2 * (readl(pllbase + PLLC_PLLM) & 0x0ff); -#else - base *= 1 + (REG(pllbase + PLLC_PLLM) & 0x0ff); -#endif - base /= pll_postdiv(pllbase); - } - return DIV_ROUND_UP(base, 1000 * pll_div(pllbase, div)); -} - -#ifdef DAVINCI_DM6467EVM -unsigned int davinci_arm_clk_get() -{ - return pll_sysclk_mhz(DAVINCI_PLL_CNTRL0_BASE, ARM_PLLDIV) * 1000000; -} -#endif - -#if defined(CONFIG_SOC_DM365) -unsigned int davinci_clk_get(unsigned int div) -{ - return pll_sysclk_mhz(DAVINCI_PLL_CNTRL0_BASE, div) * 1000000; -} -#endif - -int set_cpu_clk_info(void) -{ - unsigned int pllbase = DAVINCI_PLL_CNTRL0_BASE; -#if defined(CONFIG_SOC_DM365) - pllbase = DAVINCI_PLL_CNTRL1_BASE; -#endif - gd->bd->bi_arm_freq = pll_sysclk_mhz(pllbase, ARM_PLLDIV); - -#ifdef DSP_PLLDIV - gd->bd->bi_dsp_freq = - pll_sysclk_mhz(DAVINCI_PLL_CNTRL0_BASE, DSP_PLLDIV); -#else - gd->bd->bi_dsp_freq = 0; -#endif - - pllbase = DAVINCI_PLL_CNTRL1_BASE; -#if defined(CONFIG_SOC_DM365) - pllbase = DAVINCI_PLL_CNTRL0_BASE; -#endif - gd->bd->bi_ddr_freq = pll_sysclk_mhz(pllbase, DDR_PLLDIV) / 2; - - return 0; -} - -#endif /* !CONFIG_SOC_DA8XX */ - -/* - * Initializes on-chip ethernet controllers. - * to override, implement board_eth_init() - */ -int cpu_eth_init(bd_t *bis) -{ -#if defined(CONFIG_DRIVER_TI_EMAC) - davinci_emac_initialize(); -#endif - return 0; -} diff --git a/arch/arm/cpu/arm926ejs/davinci/da830_pinmux.c b/arch/arm/cpu/arm926ejs/davinci/da830_pinmux.c deleted file mode 100644 index edaab45327..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/da830_pinmux.c +++ /dev/null @@ -1,139 +0,0 @@ -/* - * Pinmux configurations for the DA830 SoCs - * - * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -/* SPI0 pin muxer settings */ -const struct pinmux_config spi0_pins_base[] = { - { pinmux(7), 1, 3 }, /* SPI0_SOMI */ - { pinmux(7), 1, 4 }, /* SPI0_SIMO */ - { pinmux(7), 1, 6 } /* SPI0_CLK */ -}; - -const struct pinmux_config spi0_pins_scs0[] = { - { pinmux(7), 1, 7 } /* SPI0_SCS[0] */ -}; - -const struct pinmux_config spi0_pins_ena[] = { - { pinmux(7), 1, 5 } /* SPI0_ENA */ -}; - -/* NAND pin muxer settings */ -const struct pinmux_config emifa_pins_cs0[] = { - { pinmux(18), 1, 2 } /* EMA_CS[0] */ -}; - -const struct pinmux_config emifa_pins_cs2[] = { - { pinmux(18), 1, 3 } /* EMA_CS[2] */ -}; - -const struct pinmux_config emifa_pins_cs3[] = { - { pinmux(18), 1, 4 } /* EMA_CS[3] */ -}; - -#ifdef CONFIG_USE_NAND -const struct pinmux_config emifa_pins[] = { - { pinmux(13), 1, 6 }, /* EMA_D[0] */ - { pinmux(13), 1, 7 }, /* EMA_D[1] */ - { pinmux(14), 1, 0 }, /* EMA_D[2] */ - { pinmux(14), 1, 1 }, /* EMA_D[3] */ - { pinmux(14), 1, 2 }, /* EMA_D[4] */ - { pinmux(14), 1, 3 }, /* EMA_D[5] */ - { pinmux(14), 1, 4 }, /* EMA_D[6] */ - { pinmux(14), 1, 5 }, /* EMA_D[7] */ - { pinmux(14), 1, 6 }, /* EMA_D[8] */ - { pinmux(14), 1, 7 }, /* EMA_D[9] */ - { pinmux(15), 1, 0 }, /* EMA_D[10] */ - { pinmux(15), 1, 1 }, /* EMA_D[11] */ - { pinmux(15), 1, 2 }, /* EMA_D[12] */ - { pinmux(15), 1, 3 }, /* EMA_D[13] */ - { pinmux(15), 1, 4 }, /* EMA_D[14] */ - { pinmux(15), 1, 5 }, /* EMA_D[15] */ - { pinmux(15), 1, 6 }, /* EMA_A[0] */ - { pinmux(15), 1, 7 }, /* EMA_A[1] */ - { pinmux(16), 1, 0 }, /* EMA_A[2] */ - { pinmux(16), 1, 1 }, /* EMA_A[3] */ - { pinmux(16), 1, 2 }, /* EMA_A[4] */ - { pinmux(16), 1, 3 }, /* EMA_A[5] */ - { pinmux(16), 1, 4 }, /* EMA_A[6] */ - { pinmux(16), 1, 5 }, /* EMA_A[7] */ - { pinmux(16), 1, 6 }, /* EMA_A[8] */ - { pinmux(16), 1, 7 }, /* EMA_A[9] */ - { pinmux(17), 1, 0 }, /* EMA_A[10] */ - { pinmux(17), 1, 1 }, /* EMA_A[11] */ - { pinmux(17), 1, 2 }, /* EMA_A[12] */ - { pinmux(17), 1, 3 }, /* EMA_BA[1] */ - { pinmux(17), 1, 4 }, /* EMA_BA[0] */ - { pinmux(17), 1, 5 }, /* EMA_CLK */ - { pinmux(17), 1, 6 }, /* EMA_SDCKE */ - { pinmux(17), 1, 7 }, /* EMA_CAS */ - { pinmux(18), 1, 0 }, /* EMA_CAS */ - { pinmux(18), 1, 1 }, /* EMA_WE */ - { pinmux(18), 1, 5 }, /* EMA_OE */ - { pinmux(18), 1, 6 }, /* EMA_WE_DQM[1] */ - { pinmux(18), 1, 7 }, /* EMA_WE_DQM[0] */ - { pinmux(10), 1, 0 } /* Tristate */ -}; -#endif - -/* EMAC PHY interface pins */ -const struct pinmux_config emac_pins_rmii[] = { - { pinmux(10), 2, 1 }, /* RMII_TXD[0] */ - { pinmux(10), 2, 2 }, /* RMII_TXD[1] */ - { pinmux(10), 2, 3 }, /* RMII_TXEN */ - { pinmux(10), 2, 4 }, /* RMII_CRS_DV */ - { pinmux(10), 2, 5 }, /* RMII_RXD[0] */ - { pinmux(10), 2, 6 }, /* RMII_RXD[1] */ - { pinmux(10), 2, 7 } /* RMII_RXER */ -}; - -const struct pinmux_config emac_pins_mdio[] = { - { pinmux(11), 2, 0 }, /* MDIO_CLK */ - { pinmux(11), 2, 1 } /* MDIO_D */ -}; - -const struct pinmux_config emac_pins_rmii_clk_source[] = { - { pinmux(9), 0, 5 } /* ref.clk from external source */ -}; - -/* UART2 pin muxer settings */ -const struct pinmux_config uart2_pins_txrx[] = { - { pinmux(8), 2, 7 }, /* UART2_RXD */ - { pinmux(9), 2, 0 } /* UART2_TXD */ -}; - -/* I2C0 pin muxer settings */ -const struct pinmux_config i2c0_pins[] = { - { pinmux(8), 2, 3 }, /* I2C0_SDA */ - { pinmux(8), 2, 4 } /* I2C0_SCL */ -}; - -/* USB0_DRVVBUS pin muxer settings */ -const struct pinmux_config usb_pins[] = { - { pinmux(9), 1, 1 } /* USB0_DRVVBUS */ -}; - -#ifdef CONFIG_DAVINCI_MMC -/* MMC0 pin muxer settings */ -const struct pinmux_config mmc0_pins_8bit[] = { - { pinmux(15), 2, 7 }, /* MMCSD0_CLK */ - { pinmux(16), 2, 0 }, /* MMCSD0_CMD */ - { pinmux(13), 2, 6 }, /* MMCSD0_DAT_0 */ - { pinmux(13), 2, 7 }, /* MMCSD0_DAT_1 */ - { pinmux(14), 2, 0 }, /* MMCSD0_DAT_2 */ - { pinmux(14), 2, 1 }, /* MMCSD0_DAT_3 */ - { pinmux(14), 2, 2 }, /* MMCSD0_DAT_4 */ - { pinmux(14), 2, 3 }, /* MMCSD0_DAT_5 */ - { pinmux(14), 2, 4 }, /* MMCSD0_DAT_6 */ - { pinmux(14), 2, 5 } /* MMCSD0_DAT_7 */ - /* DA830 supports 8-bit mode */ -}; -#endif diff --git a/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c b/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c deleted file mode 100644 index 19730cef8c..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c +++ /dev/null @@ -1,313 +0,0 @@ -/* - * SoC-specific lowlevel code for DA850 - * - * Copyright (C) 2011 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -void davinci_enable_uart0(void) -{ - lpsc_on(DAVINCI_LPSC_UART0); - - /* Bringup UART0 out of reset */ - REG(UART0_PWREMU_MGMT) = 0x00006001; -} - -#if defined(CONFIG_SYS_DA850_PLL_INIT) -static void da850_waitloop(unsigned long loopcnt) -{ - unsigned long i; - - for (i = 0; i < loopcnt; i++) - asm(" NOP"); -} - -static int da850_pll_init(struct davinci_pllc_regs *reg, unsigned long pllmult) -{ - if (reg == davinci_pllc0_regs) - /* Unlock PLL registers. */ - clrbits_le32(&davinci_syscfg_regs->cfgchip0, PLL_MASTER_LOCK); - - /* - * Set PLLENSRC '0',bit 5, PLL Enable(PLLEN) selection is controlled - * through MMR - */ - clrbits_le32(®->pllctl, PLLCTL_PLLENSRC); - /* PLLCTL.EXTCLKSRC bit 9 should be left at 0 for Freon */ - clrbits_le32(®->pllctl, PLLCTL_EXTCLKSRC); - - /* Set PLLEN=0 => PLL BYPASS MODE */ - clrbits_le32(®->pllctl, PLLCTL_PLLEN); - - da850_waitloop(150); - - if (reg == davinci_pllc0_regs) { - /* - * Select the Clock Mode bit 8 as External Clock or On Chip - * Oscilator - */ - dv_maskbits(®->pllctl, ~PLLCTL_RES_9); - setbits_le32(®->pllctl, - (CONFIG_SYS_DV_CLKMODE << PLLCTL_CLOCK_MODE_SHIFT)); - } - - /* Clear PLLRST bit to reset the PLL */ - clrbits_le32(®->pllctl, PLLCTL_PLLRST); - - /* Disable the PLL output */ - setbits_le32(®->pllctl, PLLCTL_PLLDIS); - - /* PLL initialization sequence */ - /* - * Power up the PLL- PWRDN bit set to 0 to bring the PLL out of - * power down bit - */ - clrbits_le32(®->pllctl, PLLCTL_PLLPWRDN); - - /* Enable the PLL from Disable Mode PLLDIS bit to 0 */ - clrbits_le32(®->pllctl, PLLCTL_PLLDIS); - -#if defined(CONFIG_SYS_DA850_PLL0_PREDIV) - /* program the prediv */ - if (reg == davinci_pllc0_regs && CONFIG_SYS_DA850_PLL0_PREDIV) - writel((PLL_DIVEN | CONFIG_SYS_DA850_PLL0_PREDIV), - ®->prediv); -#endif - - /* Program the required multiplier value in PLLM */ - writel(pllmult, ®->pllm); - - /* program the postdiv */ - if (reg == davinci_pllc0_regs) - writel((PLL_POSTDEN | CONFIG_SYS_DA850_PLL0_POSTDIV), - ®->postdiv); - else - writel((PLL_POSTDEN | CONFIG_SYS_DA850_PLL1_POSTDIV), - ®->postdiv); - - /* - * Check for the GOSTAT bit in PLLSTAT to clear to 0 to indicate that - * no GO operation is currently in progress - */ - while ((readl(®->pllstat) & PLLCMD_GOSTAT) == PLLCMD_GOSTAT) - ; - - if (reg == davinci_pllc0_regs) { - writel(CONFIG_SYS_DA850_PLL0_PLLDIV1, ®->plldiv1); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV2, ®->plldiv2); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV3, ®->plldiv3); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV4, ®->plldiv4); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV5, ®->plldiv5); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV6, ®->plldiv6); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV7, ®->plldiv7); - } else { - writel(CONFIG_SYS_DA850_PLL1_PLLDIV1, ®->plldiv1); - writel(CONFIG_SYS_DA850_PLL1_PLLDIV2, ®->plldiv2); - writel(CONFIG_SYS_DA850_PLL1_PLLDIV3, ®->plldiv3); - } - - /* - * Set the GOSET bit in PLLCMD to 1 to initiate a new divider - * transition. - */ - setbits_le32(®->pllcmd, PLLCMD_GOSTAT); - - /* - * Wait for the GOSTAT bit in PLLSTAT to clear to 0 - * (completion of phase alignment). - */ - while ((readl(®->pllstat) & PLLCMD_GOSTAT) == PLLCMD_GOSTAT) - ; - - /* Wait for PLL to reset properly. See PLL spec for PLL reset time */ - da850_waitloop(200); - - /* Set the PLLRST bit in PLLCTL to 1 to bring the PLL out of reset */ - setbits_le32(®->pllctl, PLLCTL_PLLRST); - - /* Wait for PLL to lock. See PLL spec for PLL lock time */ - da850_waitloop(2400); - - /* - * Set the PLLEN bit in PLLCTL to 1 to remove the PLL from bypass - * mode - */ - setbits_le32(®->pllctl, PLLCTL_PLLEN); - - - /* - * clear EMIFA and EMIFB clock source settings, let them - * run off SYSCLK - */ - if (reg == davinci_pllc0_regs) - dv_maskbits(&davinci_syscfg_regs->cfgchip3, - ~(PLL_SCSCFG3_DIV45PENA | PLL_SCSCFG3_EMA_CLKSRC)); - - return 0; -} -#endif /* CONFIG_SYS_DA850_PLL_INIT */ - -#if defined(CONFIG_SYS_DA850_DDR_INIT) -static int da850_ddr_setup(void) -{ - unsigned long tmp; - - /* Enable the Clock to DDR2/mDDR */ - lpsc_on(DAVINCI_LPSC_DDR_EMIF); - - tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); - if ((tmp & VTP_POWERDWN) == VTP_POWERDWN) { - /* Begin VTP Calibration */ - clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_POWERDWN); - clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_LOCK); - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); - clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); - - /* Polling READY bit to see when VTP calibration is done */ - tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); - while ((tmp & VTP_READY) != VTP_READY) - tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); - - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_LOCK); - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_POWERDWN); - } - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_IOPWRDWN); - writel(CONFIG_SYS_DA850_DDR2_DDRPHYCR, &dv_ddr2_regs_ctrl->ddrphycr); - - if (CONFIG_SYS_DA850_DDR2_SDBCR & (1 << DV_DDR_SDCR_DDR2EN_SHIFT)) { - /* DDR2 */ - clrbits_le32(&davinci_syscfg1_regs->ddr_slew, - (1 << DDR_SLEW_DDR_PDENA_BIT) | - (1 << DDR_SLEW_CMOSEN_BIT)); - } else { - /* MOBILE DDR */ - setbits_le32(&davinci_syscfg1_regs->ddr_slew, - (1 << DDR_SLEW_DDR_PDENA_BIT) | - (1 << DDR_SLEW_CMOSEN_BIT)); - } - - /* - * SDRAM Configuration Register (SDCR): - * First set the BOOTUNLOCK bit to make configuration bits - * writeable. - */ - setbits_le32(&dv_ddr2_regs_ctrl->sdbcr, DV_DDR_BOOTUNLOCK); - - /* - * Write the new value of these bits and clear BOOTUNLOCK. - * At the same time, set the TIMUNLOCK bit to allow changing - * the timing registers - */ - tmp = CONFIG_SYS_DA850_DDR2_SDBCR; - tmp &= ~DV_DDR_BOOTUNLOCK; - tmp |= DV_DDR_TIMUNLOCK; - writel(tmp, &dv_ddr2_regs_ctrl->sdbcr); - - /* write memory configuration and timing */ - if (!(CONFIG_SYS_DA850_DDR2_SDBCR & (1 << DV_DDR_SDCR_DDR2EN_SHIFT))) { - /* MOBILE DDR only*/ - writel(CONFIG_SYS_DA850_DDR2_SDBCR2, - &dv_ddr2_regs_ctrl->sdbcr2); - } - writel(CONFIG_SYS_DA850_DDR2_SDTIMR, &dv_ddr2_regs_ctrl->sdtimr); - writel(CONFIG_SYS_DA850_DDR2_SDTIMR2, &dv_ddr2_regs_ctrl->sdtimr2); - - /* clear the TIMUNLOCK bit and write the value of the CL field */ - tmp &= ~DV_DDR_TIMUNLOCK; - writel(tmp, &dv_ddr2_regs_ctrl->sdbcr); - - /* - * LPMODEN and MCLKSTOPEN must be set! - * Without this bits set, PSC don;t switch states !! - */ - writel(CONFIG_SYS_DA850_DDR2_SDRCR | - (1 << DV_DDR_SRCR_LPMODEN_SHIFT) | - (1 << DV_DDR_SRCR_MCLKSTOPEN_SHIFT), - &dv_ddr2_regs_ctrl->sdrcr); - - /* SyncReset the Clock to EMIF3A SDRAM */ - lpsc_syncreset(DAVINCI_LPSC_DDR_EMIF); - /* Enable the Clock to EMIF3A SDRAM */ - lpsc_on(DAVINCI_LPSC_DDR_EMIF); - - /* disable self refresh */ - clrbits_le32(&dv_ddr2_regs_ctrl->sdrcr, - DV_DDR_SDRCR_LPMODEN | DV_DDR_SDRCR_MCLKSTOPEN); - writel(CONFIG_SYS_DA850_DDR2_PBBPR, &dv_ddr2_regs_ctrl->pbbpr); - - return 0; -} -#endif /* CONFIG_SYS_DA850_DDR_INIT */ - -__attribute__((weak)) -void board_gpio_init(void) -{ - return; -} - -int arch_cpu_init(void) -{ - /* Unlock kick registers */ - writel(DV_SYSCFG_KICK0_UNLOCK, &davinci_syscfg_regs->kick0); - writel(DV_SYSCFG_KICK1_UNLOCK, &davinci_syscfg_regs->kick1); - - dv_maskbits(&davinci_syscfg_regs->suspsrc, - CONFIG_SYS_DA850_SYSCFG_SUSPSRC); - - /* configure pinmux settings */ - if (davinci_configure_pin_mux_items(pinmuxes, pinmuxes_size)) - return 1; - -#if defined(CONFIG_SYS_DA850_PLL_INIT) - /* PLL setup */ - da850_pll_init(davinci_pllc0_regs, CONFIG_SYS_DA850_PLL0_PLLM); - da850_pll_init(davinci_pllc1_regs, CONFIG_SYS_DA850_PLL1_PLLM); -#endif - /* setup CSn config */ -#if defined(CONFIG_SYS_DA850_CS2CFG) - writel(CONFIG_SYS_DA850_CS2CFG, &davinci_emif_regs->ab1cr); -#endif -#if defined(CONFIG_SYS_DA850_CS3CFG) - writel(CONFIG_SYS_DA850_CS3CFG, &davinci_emif_regs->ab2cr); -#endif - - da8xx_configure_lpsc_items(lpsc, lpsc_size); - - /* GPIO setup */ - board_gpio_init(); - - - NS16550_init((NS16550_t)(CONFIG_SYS_NS16550_COM1), - CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); - - /* - * Fix Power and Emulation Management Register - * see sprufw3a.pdf page 37 Table 24 - */ - writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | - DAVINCI_UART_PWREMU_MGMT_UTRST), -#if (CONFIG_SYS_NS16550_COM1 == DAVINCI_UART0_BASE) - &davinci_uart0_ctrl_regs->pwremu_mgmt); -#else - &davinci_uart2_ctrl_regs->pwremu_mgmt); -#endif - -#if defined(CONFIG_SYS_DA850_DDR_INIT) - da850_ddr_setup(); -#endif - - return 0; -} diff --git a/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c b/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c deleted file mode 100644 index 6105f6390c..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/da850_pinmux.c +++ /dev/null @@ -1,181 +0,0 @@ -/* - * Pinmux configurations for the DA850 SoCs - * - * Copyright (C) 2011 OMICRON electronics GmbH - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -/* SPI pin muxer settings */ -const struct pinmux_config spi1_pins_base[] = { - { pinmux(5), 1, 2 }, /* SPI1_CLK */ - { pinmux(5), 1, 4 }, /* SPI1_SOMI */ - { pinmux(5), 1, 5 }, /* SPI1_SIMO */ -}; - -const struct pinmux_config spi1_pins_scs0[] = { - { pinmux(5), 1, 1 }, /* SPI1_SCS[0] */ -}; - -/* UART pin muxer settings */ -const struct pinmux_config uart0_pins_txrx[] = { - { pinmux(3), 2, 4 }, /* UART0_RXD */ - { pinmux(3), 2, 5 }, /* UART0_TXD */ -}; - -const struct pinmux_config uart0_pins_rtscts[] = { - { pinmux(3), 2, 6 }, - { pinmux(3), 2, 7 }, -}; - -const struct pinmux_config uart1_pins_txrx[] = { - { pinmux(4), 2, 6 }, /* UART1_RXD */ - { pinmux(4), 2, 7 }, /* UART1_TXD */ -}; - -const struct pinmux_config uart2_pins_txrx[] = { - { pinmux(4), 2, 4 }, /* UART2_RXD */ - { pinmux(4), 2, 5 }, /* UART2_TXD */ -}; - -const struct pinmux_config uart2_pins_rtscts[] = { - { pinmux(0), 4, 6 }, /* UART2_RTS */ - { pinmux(0), 4, 7 }, /* UART2_CTS */ -}; - -/* EMAC pin muxer settings*/ -const struct pinmux_config emac_pins_rmii[] = { - { pinmux(14), 8, 2 }, /* RMII_TXD[1] */ - { pinmux(14), 8, 3 }, /* RMII_TXD[0] */ - { pinmux(14), 8, 4 }, /* RMII_TXEN */ - { pinmux(14), 8, 5 }, /* RMII_RXD[1] */ - { pinmux(14), 8, 6 }, /* RMII_RXD[0] */ - { pinmux(14), 8, 7 }, /* RMII_RXER */ - { pinmux(15), 0, 0 }, /* RMII_MHz_50_CLK */ - { pinmux(15), 8, 1 }, /* RMII_CRS_DV */ -}; - -const struct pinmux_config emac_pins_mii[] = { - { pinmux(2), 8, 1 }, /* MII_TXEN */ - { pinmux(2), 8, 2 }, /* MII_TXCLK */ - { pinmux(2), 8, 3 }, /* MII_COL */ - { pinmux(2), 8, 4 }, /* MII_TXD[3] */ - { pinmux(2), 8, 5 }, /* MII_TXD[2] */ - { pinmux(2), 8, 6 }, /* MII_TXD[1] */ - { pinmux(2), 8, 7 }, /* MII_TXD[0] */ - { pinmux(3), 8, 0 }, /* MII_RXCLK */ - { pinmux(3), 8, 1 }, /* MII_RXDV */ - { pinmux(3), 8, 2 }, /* MII_RXER */ - { pinmux(3), 8, 3 }, /* MII_CRS */ - { pinmux(3), 8, 4 }, /* MII_RXD[3] */ - { pinmux(3), 8, 5 }, /* MII_RXD[2] */ - { pinmux(3), 8, 6 }, /* MII_RXD[1] */ - { pinmux(3), 8, 7 }, /* MII_RXD[0] */ -}; - -const struct pinmux_config emac_pins_mdio[] = { - { pinmux(4), 8, 0 }, /* MDIO_CLK */ - { pinmux(4), 8, 1 }, /* MDIO_D */ -}; - -/* I2C pin muxer settings */ -const struct pinmux_config i2c0_pins[] = { - { pinmux(4), 2, 2 }, /* I2C0_SCL */ - { pinmux(4), 2, 3 }, /* I2C0_SDA */ -}; - -const struct pinmux_config i2c1_pins[] = { - { pinmux(4), 4, 4 }, /* I2C1_SCL */ - { pinmux(4), 4, 5 }, /* I2C1_SDA */ -}; - -/* EMIFA pin muxer settings */ -const struct pinmux_config emifa_pins_cs2[] = { - { pinmux(7), 1, 0 }, /* EMA_CS2 */ -}; - -const struct pinmux_config emifa_pins_cs3[] = { - { pinmux(7), 1, 1 }, /* EMA_CS[3] */ -}; - -const struct pinmux_config emifa_pins_cs4[] = { - { pinmux(7), 1, 2 }, /* EMA_CS[4] */ -}; - -const struct pinmux_config emifa_pins_nand[] = { - { pinmux(7), 1, 4 }, /* EMA_WE */ - { pinmux(7), 1, 5 }, /* EMA_OE */ - { pinmux(9), 1, 0 }, /* EMA_D[7] */ - { pinmux(9), 1, 1 }, /* EMA_D[6] */ - { pinmux(9), 1, 2 }, /* EMA_D[5] */ - { pinmux(9), 1, 3 }, /* EMA_D[4] */ - { pinmux(9), 1, 4 }, /* EMA_D[3] */ - { pinmux(9), 1, 5 }, /* EMA_D[2] */ - { pinmux(9), 1, 6 }, /* EMA_D[1] */ - { pinmux(9), 1, 7 }, /* EMA_D[0] */ - { pinmux(12), 1, 5 }, /* EMA_A[2] */ - { pinmux(12), 1, 6 }, /* EMA_A[1] */ -}; - -/* NOR pin muxer settings */ -const struct pinmux_config emifa_pins_nor[] = { - { pinmux(5), 1, 6 }, /* EMA_BA[1] */ - { pinmux(6), 1, 6 }, /* EMA_WAIT[1] */ - { pinmux(7), 1, 4 }, /* EMA_WE */ - { pinmux(7), 1, 5 }, /* EMA_OE */ - { pinmux(8), 1, 0 }, /* EMA_D[15] */ - { pinmux(8), 1, 1 }, /* EMA_D[14] */ - { pinmux(8), 1, 2 }, /* EMA_D[13] */ - { pinmux(8), 1, 3 }, /* EMA_D[12] */ - { pinmux(8), 1, 4 }, /* EMA_D[11] */ - { pinmux(8), 1, 5 }, /* EMA_D[10] */ - { pinmux(8), 1, 6 }, /* EMA_D[9] */ - { pinmux(8), 1, 7 }, /* EMA_D[8] */ - { pinmux(9), 1, 0 }, /* EMA_D[7] */ - { pinmux(9), 1, 1 }, /* EMA_D[6] */ - { pinmux(9), 1, 2 }, /* EMA_D[5] */ - { pinmux(9), 1, 3 }, /* EMA_D[4] */ - { pinmux(9), 1, 4 }, /* EMA_D[3] */ - { pinmux(9), 1, 5 }, /* EMA_D[2] */ - { pinmux(9), 1, 6 }, /* EMA_D[1] */ - { pinmux(9), 1, 7 }, /* EMA_D[0] */ - { pinmux(10), 1, 1 }, /* EMA_A[22] */ - { pinmux(10), 1, 2 }, /* EMA_A[21] */ - { pinmux(10), 1, 3 }, /* EMA_A[20] */ - { pinmux(10), 1, 4 }, /* EMA_A[19] */ - { pinmux(10), 1, 5 }, /* EMA_A[18] */ - { pinmux(10), 1, 6 }, /* EMA_A[17] */ - { pinmux(10), 1, 7 }, /* EMA_A[16] */ - { pinmux(11), 1, 0 }, /* EMA_A[15] */ - { pinmux(11), 1, 1 }, /* EMA_A[14] */ - { pinmux(11), 1, 2 }, /* EMA_A[13] */ - { pinmux(11), 1, 3 }, /* EMA_A[12] */ - { pinmux(11), 1, 4 }, /* EMA_A[11] */ - { pinmux(11), 1, 5 }, /* EMA_A[10] */ - { pinmux(11), 1, 6 }, /* EMA_A[9] */ - { pinmux(11), 1, 7 }, /* EMA_A[8] */ - { pinmux(12), 1, 0 }, /* EMA_A[7] */ - { pinmux(12), 1, 1 }, /* EMA_A[6] */ - { pinmux(12), 1, 2 }, /* EMA_A[5] */ - { pinmux(12), 1, 3 }, /* EMA_A[4] */ - { pinmux(12), 1, 4 }, /* EMA_A[3] */ - { pinmux(12), 1, 5 }, /* EMA_A[2] */ - { pinmux(12), 1, 6 }, /* EMA_A[1] */ - { pinmux(12), 1, 7 }, /* EMA_A[0] */ -}; - -/* MMC0 pin muxer settings */ -const struct pinmux_config mmc0_pins[] = { - { pinmux(10), 2, 0 }, /* MMCSD0_CLK */ - { pinmux(10), 2, 1 }, /* MMCSD0_CMD */ - { pinmux(10), 2, 2 }, /* MMCSD0_DAT_0 */ - { pinmux(10), 2, 3 }, /* MMCSD0_DAT_1 */ - { pinmux(10), 2, 4 }, /* MMCSD0_DAT_2 */ - { pinmux(10), 2, 5 }, /* MMCSD0_DAT_3 */ - /* DA850 supports only 4-bit mode, remaining pins are not configured */ -}; diff --git a/arch/arm/cpu/arm926ejs/davinci/dm355.c b/arch/arm/cpu/arm926ejs/davinci/dm355.c deleted file mode 100644 index f9550a16d3..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/dm355.c +++ /dev/null @@ -1,30 +0,0 @@ -/* - * SoC-specific code for tms320dm355 and similar chips - * - * Copyright (C) 2009 David Brownell - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - - -void davinci_enable_uart0(void) -{ - lpsc_on(DAVINCI_LPSC_UART0); - - /* Bringup UART0 out of reset */ - REG(UART0_PWREMU_MGMT) = 0x00006001; -} - - -#ifdef CONFIG_SYS_I2C_DAVINCI -void davinci_enable_i2c(void) -{ - lpsc_on(DAVINCI_LPSC_I2C); - - /* Enable I2C pin Mux */ - REG(PINMUX3) |= (1 << 20) | (1 << 19); -} -#endif diff --git a/arch/arm/cpu/arm926ejs/davinci/dm365.c b/arch/arm/cpu/arm926ejs/davinci/dm365.c deleted file mode 100644 index f6ca527e74..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/dm365.c +++ /dev/null @@ -1,20 +0,0 @@ -/* - * SoC-specific code for tms320dm365 and similar chips - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - -void davinci_enable_uart0(void) -{ - lpsc_on(DAVINCI_LPSC_UART0); -} - -#ifdef CONFIG_SYS_I2C_DAVINCI -void davinci_enable_i2c(void) -{ - lpsc_on(DAVINCI_LPSC_I2C); -} -#endif diff --git a/arch/arm/cpu/arm926ejs/davinci/dm365_lowlevel.c b/arch/arm/cpu/arm926ejs/davinci/dm365_lowlevel.c deleted file mode 100644 index c8b44988d3..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/dm365_lowlevel.c +++ /dev/null @@ -1,460 +0,0 @@ -/* - * SoC-specific lowlevel code for tms320dm365 and similar chips - * Actually used for booting from NAND with nand_spl. - * - * Copyright (C) 2011 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include -#include -#include -#include -#include -#include -#include - -void dm365_waitloop(unsigned long loopcnt) -{ - unsigned long i; - - for (i = 0; i < loopcnt; i++) - asm(" NOP"); -} - -int dm365_pll1_init(unsigned long pllmult, unsigned long prediv) -{ - unsigned int clksrc = 0x0; - - /* Power up the PLL */ - clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLPWRDN); - - clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_RES_9); - setbits_le32(&dv_pll0_regs->pllctl, - clksrc << PLLCTL_CLOCK_MODE_SHIFT); - - /* - * Set PLLENSRC '0', PLL Enable(PLLEN) selection is controlled - * through MMR - */ - clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLENSRC); - - /* Set PLLEN=0 => PLL BYPASS MODE */ - clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLEN); - - dm365_waitloop(150); - - /* PLLRST=1(reset assert) */ - setbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLRST); - - dm365_waitloop(300); - - /*Bring PLL out of Reset*/ - clrbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLRST); - - /* Program the Multiper and Pre-Divider for PLL1 */ - writel(pllmult, &dv_pll0_regs->pllm); - writel(prediv, &dv_pll0_regs->prediv); - - /* Assert TENABLE = 1, TENABLEDIV = 1, TINITZ = 1 */ - writel(PLLSECCTL_STOPMODE | PLLSECCTL_TENABLEDIV | PLLSECCTL_TENABLE | - PLLSECCTL_TINITZ, &dv_pll0_regs->secctl); - /* Assert TENABLE = 1, TENABLEDIV = 1, TINITZ = 0 */ - writel(PLLSECCTL_STOPMODE | PLLSECCTL_TENABLEDIV | PLLSECCTL_TENABLE, - &dv_pll0_regs->secctl); - /* Assert TENABLE = 0, TENABLEDIV = 0, TINITZ = 0 */ - writel(PLLSECCTL_STOPMODE, &dv_pll0_regs->secctl); - /* Assert TENABLE = 0, TENABLEDIV = 0, TINITZ = 1 */ - writel(PLLSECCTL_STOPMODE | PLLSECCTL_TINITZ, &dv_pll0_regs->secctl); - - /* Program the PostDiv for PLL1 */ - writel(PLL_POSTDEN, &dv_pll0_regs->postdiv); - - /* Post divider setting for PLL1 */ - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV1, &dv_pll0_regs->plldiv1); - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV2, &dv_pll0_regs->plldiv2); - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV3, &dv_pll0_regs->plldiv3); - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV4, &dv_pll0_regs->plldiv4); - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV5, &dv_pll0_regs->plldiv5); - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV6, &dv_pll0_regs->plldiv6); - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV7, &dv_pll0_regs->plldiv7); - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV8, &dv_pll0_regs->plldiv8); - writel(CONFIG_SYS_DM36x_PLL1_PLLDIV9, &dv_pll0_regs->plldiv9); - - dm365_waitloop(300); - - /* Set the GOSET bit */ - writel(PLLCMD_GOSET, &dv_pll0_regs->pllcmd); /* Go */ - - dm365_waitloop(300); - - /* Wait for PLL to LOCK */ - while (!((readl(&dv_sys_module_regs->pll0_config) & PLL0_LOCK) - == PLL0_LOCK)) - ; - - /* Enable the PLL Bit of PLLCTL*/ - setbits_le32(&dv_pll0_regs->pllctl, PLLCTL_PLLEN); - - return 0; -} - -int dm365_pll2_init(unsigned long pllm, unsigned long prediv) -{ - unsigned int clksrc = 0x0; - - /* Power up the PLL*/ - clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLPWRDN); - - /* - * Select the Clock Mode as Onchip Oscilator or External Clock on - * MXI pin - * VDB has input on MXI pin - */ - clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_RES_9); - setbits_le32(&dv_pll1_regs->pllctl, - clksrc << PLLCTL_CLOCK_MODE_SHIFT); - - /* - * Set PLLENSRC '0', PLL Enable(PLLEN) selection is controlled - * through MMR - */ - clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLENSRC); - - /* Set PLLEN=0 => PLL BYPASS MODE */ - clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLEN); - - dm365_waitloop(50); - - /* PLLRST=1(reset assert) */ - setbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLRST); - - dm365_waitloop(300); - - /* Bring PLL out of Reset */ - clrbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLRST); - - /* Program the Multiper and Pre-Divider for PLL2 */ - writel(pllm, &dv_pll1_regs->pllm); - writel(prediv, &dv_pll1_regs->prediv); - - writel(PLL_POSTDEN, &dv_pll1_regs->postdiv); - - /* Assert TENABLE = 1, TENABLEDIV = 1, TINITZ = 1 */ - writel(PLLSECCTL_STOPMODE | PLLSECCTL_TENABLEDIV | PLLSECCTL_TENABLE | - PLLSECCTL_TINITZ, &dv_pll1_regs->secctl); - /* Assert TENABLE = 1, TENABLEDIV = 1, TINITZ = 0 */ - writel(PLLSECCTL_STOPMODE | PLLSECCTL_TENABLEDIV | PLLSECCTL_TENABLE, - &dv_pll1_regs->secctl); - /* Assert TENABLE = 0, TENABLEDIV = 0, TINITZ = 0 */ - writel(PLLSECCTL_STOPMODE, &dv_pll1_regs->secctl); - /* Assert TENABLE = 0, TENABLEDIV = 0, TINITZ = 1 */ - writel(PLLSECCTL_STOPMODE | PLLSECCTL_TINITZ, &dv_pll1_regs->secctl); - - /* Post divider setting for PLL2 */ - writel(CONFIG_SYS_DM36x_PLL2_PLLDIV1, &dv_pll1_regs->plldiv1); - writel(CONFIG_SYS_DM36x_PLL2_PLLDIV2, &dv_pll1_regs->plldiv2); - writel(CONFIG_SYS_DM36x_PLL2_PLLDIV3, &dv_pll1_regs->plldiv3); - writel(CONFIG_SYS_DM36x_PLL2_PLLDIV4, &dv_pll1_regs->plldiv4); - writel(CONFIG_SYS_DM36x_PLL2_PLLDIV5, &dv_pll1_regs->plldiv5); - - /* GoCmd for PostDivider to take effect */ - writel(PLLCMD_GOSET, &dv_pll1_regs->pllcmd); - - dm365_waitloop(150); - - /* Wait for PLL to LOCK */ - while (!((readl(&dv_sys_module_regs->pll1_config) & PLL1_LOCK) - == PLL1_LOCK)) - ; - - dm365_waitloop(4100); - - /* Enable the PLL2 */ - setbits_le32(&dv_pll1_regs->pllctl, PLLCTL_PLLEN); - - /* do this after PLL's have been set up */ - writel(CONFIG_SYS_DM36x_PERI_CLK_CTRL, - &dv_sys_module_regs->peri_clkctl); - - return 0; -} - -int dm365_ddr_setup(void) -{ - lpsc_on(DAVINCI_LPSC_DDR_EMIF); - clrbits_le32(&dv_sys_module_regs->vtpiocr, - VPTIO_IOPWRDN | VPTIO_CLRZ | VPTIO_LOCK | VPTIO_PWRDN); - - /* Set bit CLRZ (bit 13) */ - setbits_le32(&dv_sys_module_regs->vtpiocr, VPTIO_CLRZ); - - /* Check VTP READY Status */ - while (!(readl(&dv_sys_module_regs->vtpiocr) & VPTIO_RDY)) - ; - - /* Set bit VTP_IOPWRDWN bit 14 for DDR input buffers) */ - setbits_le32(&dv_sys_module_regs->vtpiocr, VPTIO_IOPWRDN); - - /* Set bit LOCK(bit7) */ - setbits_le32(&dv_sys_module_regs->vtpiocr, VPTIO_LOCK); - - /* - * Powerdown VTP as it is locked (bit 6) - * Set bit VTP_IOPWRDWN bit 14 for DDR input buffers) - */ - setbits_le32(&dv_sys_module_regs->vtpiocr, - VPTIO_IOPWRDN | VPTIO_PWRDN); - - /* Wait for calibration to complete */ - dm365_waitloop(150); - - /* Set the DDR2 to synreset, then enable it again */ - lpsc_syncreset(DAVINCI_LPSC_DDR_EMIF); - lpsc_on(DAVINCI_LPSC_DDR_EMIF); - - writel(CONFIG_SYS_DM36x_DDR2_DDRPHYCR, &dv_ddr2_regs_ctrl->ddrphycr); - - /* Program SDRAM Bank Config Register */ - writel((CONFIG_SYS_DM36x_DDR2_SDBCR | DV_DDR_BOOTUNLOCK), - &dv_ddr2_regs_ctrl->sdbcr); - writel((CONFIG_SYS_DM36x_DDR2_SDBCR | DV_DDR_TIMUNLOCK), - &dv_ddr2_regs_ctrl->sdbcr); - - /* Program SDRAM Timing Control Register1 */ - writel(CONFIG_SYS_DM36x_DDR2_SDTIMR, &dv_ddr2_regs_ctrl->sdtimr); - /* Program SDRAM Timing Control Register2 */ - writel(CONFIG_SYS_DM36x_DDR2_SDTIMR2, &dv_ddr2_regs_ctrl->sdtimr2); - - writel(CONFIG_SYS_DM36x_DDR2_PBBPR, &dv_ddr2_regs_ctrl->pbbpr); - - writel(CONFIG_SYS_DM36x_DDR2_SDBCR, &dv_ddr2_regs_ctrl->sdbcr); - - /* Program SDRAM Refresh Control Register */ - writel(CONFIG_SYS_DM36x_DDR2_SDRCR, &dv_ddr2_regs_ctrl->sdrcr); - - lpsc_syncreset(DAVINCI_LPSC_DDR_EMIF); - lpsc_on(DAVINCI_LPSC_DDR_EMIF); - - return 0; -} - -static void dm365_vpss_sync_reset(void) -{ - unsigned int PdNum = 0; - - /* VPSS_CLKMD 1:1 */ - setbits_le32(&dv_sys_module_regs->vpss_clkctl, - VPSS_CLK_CTL_VPSS_CLKMD); - - /* LPSC SyncReset DDR Clock Enable */ - writel(((readl(&dv_psc_regs->mdctl[DAVINCI_LPSC_VPSSMASTER]) & - ~PSC_MD_STATE_MSK) | PSC_SYNCRESET), - &dv_psc_regs->mdctl[DAVINCI_LPSC_VPSSMASTER]); - - writel((1 << PdNum), &dv_psc_regs->ptcmd); - - while (!(((readl(&dv_psc_regs->ptstat) >> PdNum) & PSC_GOSTAT) == 0)) - ; - while (!((readl(&dv_psc_regs->mdstat[DAVINCI_LPSC_VPSSMASTER]) & - PSC_MD_STATE_MSK) == PSC_SYNCRESET)) - ; -} - -static void dm365_por_reset(void) -{ - struct davinci_timer *wdog = - (struct davinci_timer *)DAVINCI_WDOG_BASE; - - if (readl(&dv_pll0_regs->rstype) & - (PLL_RSTYPE_POR | PLL_RSTYPE_XWRST)) { - dm365_vpss_sync_reset(); - - writel(DV_TMPBUF_VAL, TMPBUF); - setbits_le32(TMPSTATUS, FLAG_PORRST); - writel(DV_WDT_ENABLE_SYS_RESET, &wdog->na1); - writel(DV_WDT_TRIGGER_SYS_RESET, &wdog->na2); - - while (1); - } -} - -static void dm365_wdt_reset(void) -{ - struct davinci_timer *wdog = - (struct davinci_timer *)DAVINCI_WDOG_BASE; - - if (readl(TMPBUF) != DV_TMPBUF_VAL) { - writel(DV_TMPBUF_VAL, TMPBUF); - setbits_le32(TMPSTATUS, FLAG_PORRST); - setbits_le32(TMPSTATUS, FLAG_FLGOFF); - - dm365_waitloop(100); - - dm365_vpss_sync_reset(); - - writel(DV_WDT_ENABLE_SYS_RESET, &wdog->na1); - writel(DV_WDT_TRIGGER_SYS_RESET, &wdog->na2); - - while (1); - } -} - -static void dm365_wdt_flag_on(void) -{ - /* VPSS_CLKMD 1:2 */ - clrbits_le32(&dv_sys_module_regs->vpss_clkctl, - VPSS_CLK_CTL_VPSS_CLKMD); - writel(0, TMPBUF); - setbits_le32(TMPSTATUS, FLAG_FLGON); -} - -void dm365_psc_init(void) -{ - unsigned char i = 0; - unsigned char lpsc_start; - unsigned char lpsc_end, lpscgroup, lpscmin, lpscmax; - unsigned int PdNum = 0; - - lpscmin = 0; - lpscmax = 2; - - for (lpscgroup = lpscmin; lpscgroup <= lpscmax; lpscgroup++) { - if (lpscgroup == 0) { - /* Enabling LPSC 3 to 28 SCR first */ - lpsc_start = DAVINCI_LPSC_VPSSMSTR; - lpsc_end = DAVINCI_LPSC_TIMER1; - } else if (lpscgroup == 1) { /* Skip locked LPSCs [29-37] */ - lpsc_start = DAVINCI_LPSC_CFG5; - lpsc_end = DAVINCI_LPSC_VPSSMASTER; - } else { - lpsc_start = DAVINCI_LPSC_MJCP; - lpsc_end = DAVINCI_LPSC_HDVICP; - } - - /* NEXT=0x3, Enable LPSC's */ - for (i = lpsc_start; i <= lpsc_end; i++) - setbits_le32(&dv_psc_regs->mdctl[i], PSC_ENABLE); - - /* - * Program goctl to start transition sequence for LPSCs - * CSL_PSC_0_REGS->PTCMD = (1<ptcmd); - - /* - * Wait for GOSTAT = NO TRANSITION from PSC for Powerdomain 0 - */ - while (!(((readl(&dv_psc_regs->ptstat) >> PdNum) & PSC_GOSTAT) - == 0)) - ; - - /* Wait for MODSTAT = ENABLE from LPSC's */ - for (i = lpsc_start; i <= lpsc_end; i++) - while (!((readl(&dv_psc_regs->mdstat[i]) & - PSC_MD_STATE_MSK) == PSC_ENABLE)) - ; - } -} - -static void dm365_emif_init(void) -{ - writel(CONFIG_SYS_DM36x_AWCCR, &davinci_emif_regs->awccr); - writel(CONFIG_SYS_DM36x_AB1CR, &davinci_emif_regs->ab1cr); - - setbits_le32(&davinci_emif_regs->nandfcr, DAVINCI_NANDFCR_CS2NAND); - - writel(CONFIG_SYS_DM36x_AB2CR, &davinci_emif_regs->ab2cr); - - return; -} - -void dm365_pinmux_ctl(unsigned long offset, unsigned long mask, - unsigned long value) -{ - clrbits_le32(&dv_sys_module_regs->pinmux[offset], mask); - setbits_le32(&dv_sys_module_regs->pinmux[offset], (mask & value)); -} - -__attribute__((weak)) -void board_gpio_init(void) -{ - return; -} - -#if defined(CONFIG_POST) -int post_log(char *format, ...) -{ - return 0; -} -#endif - -void dm36x_lowlevel_init(ulong bootflag) -{ - struct davinci_uart_ctrl_regs *davinci_uart_ctrl_regs = - (struct davinci_uart_ctrl_regs *)(CONFIG_SYS_NS16550_COM1 + - DAVINCI_UART_CTRL_BASE); - - /* Mask all interrupts */ - writel(DV_AINTC_INTCTL_IDMODE, &dv_aintc_regs->intctl); - writel(0x0, &dv_aintc_regs->eabase); - writel(0x0, &dv_aintc_regs->eint0); - writel(0x0, &dv_aintc_regs->eint1); - - /* Clear all interrupts */ - writel(0xffffffff, &dv_aintc_regs->fiq0); - writel(0xffffffff, &dv_aintc_regs->fiq1); - writel(0xffffffff, &dv_aintc_regs->irq0); - writel(0xffffffff, &dv_aintc_regs->irq1); - - dm365_por_reset(); - dm365_wdt_reset(); - - /* System PSC setup - enable all */ - dm365_psc_init(); - - /* Setup Pinmux */ - dm365_pinmux_ctl(0, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX0); - dm365_pinmux_ctl(1, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX1); - dm365_pinmux_ctl(2, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX2); - dm365_pinmux_ctl(3, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX3); - dm365_pinmux_ctl(4, 0xFFFFFFFF, CONFIG_SYS_DM36x_PINMUX4); - - /* PLL setup */ - dm365_pll1_init(CONFIG_SYS_DM36x_PLL1_PLLM, - CONFIG_SYS_DM36x_PLL1_PREDIV); - dm365_pll2_init(CONFIG_SYS_DM36x_PLL2_PLLM, - CONFIG_SYS_DM36x_PLL2_PREDIV); - - /* GPIO setup */ - board_gpio_init(); - - NS16550_init((NS16550_t)(CONFIG_SYS_NS16550_COM1), - CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); - - /* - * Fix Power and Emulation Management Register - * see sprufh2.pdf page 38 Table 22 - */ - writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | - DAVINCI_UART_PWREMU_MGMT_UTRST), - &davinci_uart_ctrl_regs->pwremu_mgmt); - - puts("ddr init\n"); - dm365_ddr_setup(); - - puts("emif init\n"); - dm365_emif_init(); - - dm365_wdt_flag_on(); - -#if defined(CONFIG_POST) - /* - * Do memory tests, calls arch_memory_failure_handle() - * if error detected. - */ - memory_post_test(0); -#endif -} diff --git a/arch/arm/cpu/arm926ejs/davinci/dm644x.c b/arch/arm/cpu/arm926ejs/davinci/dm644x.c deleted file mode 100644 index c58e271e28..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/dm644x.c +++ /dev/null @@ -1,81 +0,0 @@ -/* - * SoC-specific code for tms320dm644x chips - * - * Copyright (C) 2007 Sergey Kubushyn - * Copyright (C) 2008 Lyrtech - * Copyright (C) 2004 Texas Instruments. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include - - -#define PINMUX0_EMACEN (1 << 31) -#define PINMUX0_AECS5 (1 << 11) -#define PINMUX0_AECS4 (1 << 10) - -#define PINMUX1_I2C (1 << 7) -#define PINMUX1_UART1 (1 << 1) -#define PINMUX1_UART0 (1 << 0) - - -void davinci_enable_uart0(void) -{ - lpsc_on(DAVINCI_LPSC_UART0); - - /* Bringup UART0 out of reset */ - REG(UART0_PWREMU_MGMT) = 0x00006001; - - /* Enable UART0 MUX lines */ - REG(PINMUX1) |= PINMUX1_UART0; -} - -#ifdef CONFIG_DRIVER_TI_EMAC -void davinci_enable_emac(void) -{ - lpsc_on(DAVINCI_LPSC_EMAC); - lpsc_on(DAVINCI_LPSC_EMAC_WRAPPER); - lpsc_on(DAVINCI_LPSC_MDIO); - - /* Enable GIO3.3V cells used for EMAC */ - REG(VDD3P3V_PWDN) = 0; - - /* Enable EMAC. */ - REG(PINMUX0) |= PINMUX0_EMACEN; -} -#endif - -#ifdef CONFIG_SYS_I2C_DAVINCI -void davinci_enable_i2c(void) -{ - lpsc_on(DAVINCI_LPSC_I2C); - - /* Enable I2C pin Mux */ - REG(PINMUX1) |= PINMUX1_I2C; -} -#endif - -void davinci_errata_workarounds(void) -{ - /* - * Workaround for TMS320DM6446 errata 1.3.22: - * PSC: PTSTAT Register Does Not Clear After Warm/Maximum Reset - * Revision(s) Affected: 1.3 and earlier - */ - REG(PSC_SILVER_BULLET) = 0; - - /* - * Set the PR_OLD_COUNT bits in the Bus Burst Priority Register (PBBPR) - * as suggested in TMS320DM6446 errata 2.1.2: - * - * On DM6446 Silicon Revision 2.1 and earlier, under certain conditions - * low priority modules can occupy the bus and prevent high priority - * modules like the VPSS from getting the required DDR2 throughput. - * A hex value of 0x20 should provide a good ARM (cache enabled) - * performance and still allow good utilization by the VPSS or other - * modules. - */ - REG(VBPR) = 0x20; -} diff --git a/arch/arm/cpu/arm926ejs/davinci/dm646x.c b/arch/arm/cpu/arm926ejs/davinci/dm646x.c deleted file mode 100644 index cfea8300de..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/dm646x.c +++ /dev/null @@ -1,26 +0,0 @@ -/* - * SoC-specific code for TMS320DM646x chips - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include - -void davinci_enable_uart0(void) -{ - lpsc_on(DAVINCI_DM646X_LPSC_UART0); -} - -#ifdef CONFIG_DRIVER_TI_EMAC -void davinci_enable_emac(void) -{ - lpsc_on(DAVINCI_DM646X_LPSC_EMAC); -} -#endif - -#ifdef CONFIG_SYS_I2C_DAVINCI -void davinci_enable_i2c(void) -{ - lpsc_on(DAVINCI_DM646X_LPSC_I2C); -} -#endif diff --git a/arch/arm/cpu/arm926ejs/davinci/dp83848.c b/arch/arm/cpu/arm926ejs/davinci/dp83848.c deleted file mode 100644 index 603d507c70..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/dp83848.c +++ /dev/null @@ -1,128 +0,0 @@ -/* - * National Semiconductor DP83848 PHY Driver for TI DaVinci - * (TMS320DM644x) based boards. - * - * Copyright (C) 2007 Sergey Kubushyn - * - * -------------------------------------------------------- - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include "../../../../../drivers/net/davinci_emac.h" - -#ifdef CONFIG_DRIVER_TI_EMAC - -#ifdef CONFIG_CMD_NET - -int dp83848_is_phy_connected(int phy_addr) -{ - u_int16_t id1, id2; - - if (!davinci_eth_phy_read(phy_addr, DP83848_PHYID1_REG, &id1)) - return(0); - if (!davinci_eth_phy_read(phy_addr, DP83848_PHYID2_REG, &id2)) - return(0); - - if ((id1 == DP83848_PHYID1_OUI) && (id2 == DP83848_PHYID2_OUI)) - return(1); - - return(0); -} - -int dp83848_get_link_speed(int phy_addr) -{ - u_int16_t tmp; - volatile emac_regs* emac = (emac_regs *)EMAC_BASE_ADDR; - - if (!davinci_eth_phy_read(phy_addr, DP83848_STAT_REG, &tmp)) - return(0); - - if (!(tmp & DP83848_LINK_STATUS)) /* link up? */ - return(0); - - if (!davinci_eth_phy_read(phy_addr, DP83848_PHY_STAT_REG, &tmp)) - return(0); - - /* Speed doesn't matter, there is no setting for it in EMAC... */ - if (tmp & DP83848_DUPLEX) { - /* set DM644x EMAC for Full Duplex */ - emac->MACCONTROL = EMAC_MACCONTROL_MIIEN_ENABLE | - EMAC_MACCONTROL_FULLDUPLEX_ENABLE; - } else { - /*set DM644x EMAC for Half Duplex */ - emac->MACCONTROL = EMAC_MACCONTROL_MIIEN_ENABLE; - } - - return(1); -} - - -int dp83848_init_phy(int phy_addr) -{ - int ret = 1; - - if (!dp83848_get_link_speed(phy_addr)) { - /* Try another time */ - udelay(100000); - ret = dp83848_get_link_speed(phy_addr); - } - - /* Disable PHY Interrupts */ - davinci_eth_phy_write(phy_addr, DP83848_PHY_INTR_CTRL_REG, 0); - - return(ret); -} - - -int dp83848_auto_negotiate(int phy_addr) -{ - u_int16_t tmp; - - - if (!davinci_eth_phy_read(phy_addr, DP83848_CTL_REG, &tmp)) - return(0); - - /* Restart Auto_negotiation */ - tmp &= ~DP83848_AUTONEG; /* remove autonegotiation enable */ - tmp |= DP83848_ISOLATE; /* Electrically isolate PHY */ - davinci_eth_phy_write(phy_addr, DP83848_CTL_REG, tmp); - - /* Set the Auto_negotiation Advertisement Register - * MII advertising for Next page, 100BaseTxFD and HD, - * 10BaseTFD and HD, IEEE 802.3 - */ - tmp = DP83848_NP | DP83848_TX_FDX | DP83848_TX_HDX | - DP83848_10_FDX | DP83848_10_HDX | DP83848_AN_IEEE_802_3; - davinci_eth_phy_write(phy_addr, DP83848_ANA_REG, tmp); - - - /* Read Control Register */ - if (!davinci_eth_phy_read(phy_addr, DP83848_CTL_REG, &tmp)) - return(0); - - tmp |= DP83848_SPEED_SELECT | DP83848_AUTONEG | DP83848_DUPLEX_MODE; - davinci_eth_phy_write(phy_addr, DP83848_CTL_REG, tmp); - - /* Restart Auto_negotiation */ - tmp |= DP83848_RESTART_AUTONEG; - davinci_eth_phy_write(phy_addr, DP83848_CTL_REG, tmp); - - /*check AutoNegotiate complete */ - udelay(10000); - if (!davinci_eth_phy_read(phy_addr, DP83848_STAT_REG, &tmp)) - return(0); - - if (!(tmp & DP83848_AUTONEG_COMP)) - return(0); - - return (dp83848_get_link_speed(phy_addr)); -} - -#endif /* CONFIG_CMD_NET */ - -#endif /* CONFIG_DRIVER_ETHER */ diff --git a/arch/arm/cpu/arm926ejs/davinci/et1011c.c b/arch/arm/cpu/arm926ejs/davinci/et1011c.c deleted file mode 100644 index 9d53875b93..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/et1011c.c +++ /dev/null @@ -1,42 +0,0 @@ -/* - * LSI ET1011C PHY Driver for TI DaVinci(TMS320DM6467) board. - * - * Copyright (C) 2010 Texas Instruments Incorporated - http://www.ti.com/ - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include "../../../../../drivers/net/davinci_emac.h" - -#ifdef CONFIG_DRIVER_TI_EMAC - -#ifdef CONFIG_CMD_NET - -/* LSI PHYSICAL LAYER TRANSCEIVER ET1011C */ - -#define MII_PHY_CONFIG_REG 22 - -/* PHY Config bits */ -#define PHY_SYS_CLK_EN (1 << 4) - -int et1011c_get_link_speed(int phy_addr) -{ - u_int16_t data; - - if (davinci_eth_phy_read(phy_addr, MII_STATUS_REG, &data) && (data & 0x04)) { - davinci_eth_phy_read(phy_addr, MII_PHY_CONFIG_REG, &data); - /* Enable 125MHz clock sourced from PHY */ - davinci_eth_phy_write(phy_addr, MII_PHY_CONFIG_REG, - data | PHY_SYS_CLK_EN); - return (1); - } - return (0); -} - -#endif /* CONFIG_CMD_NET */ - -#endif /* CONFIG_DRIVER_ETHER */ diff --git a/arch/arm/cpu/arm926ejs/davinci/ksz8873.c b/arch/arm/cpu/arm926ejs/davinci/ksz8873.c deleted file mode 100644 index 4af5dd2135..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/ksz8873.c +++ /dev/null @@ -1,53 +0,0 @@ -/* - * Micrel KSZ8873 PHY Driver for TI DaVinci - * (TMS320DM644x) based boards. - * - * Copyright (C) 2011 Heiko Schocher - * - * based on: - * National Semiconductor DP83848 PHY Driver for TI DaVinci - * (TMS320DM644x) based boards. - * - * Copyright (C) 2007 Sergey Kubushyn - * - * -------------------------------------------------------- - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include "../../../../../drivers/net/davinci_emac.h" - -int ksz8873_is_phy_connected(int phy_addr) -{ - u_int16_t dummy; - - return davinci_eth_phy_read(phy_addr, MII_PHYSID1, &dummy); -} - -int ksz8873_get_link_speed(int phy_addr) -{ - emac_regs *emac = (emac_regs *)EMAC_BASE_ADDR; - - /* we always have a link to the switch, 100 FD */ - writel((EMAC_MACCONTROL_MIIEN_ENABLE | - EMAC_MACCONTROL_FULLDUPLEX_ENABLE), - &emac->MACCONTROL); - return 1; -} - - -int ksz8873_init_phy(int phy_addr) -{ - return 1; -} - - -int ksz8873_auto_negotiate(int phy_addr) -{ - return dp83848_get_link_speed(phy_addr); -} diff --git a/arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S b/arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S deleted file mode 100644 index e91623497c..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/lowlevel_init.S +++ /dev/null @@ -1,693 +0,0 @@ -/* - * Low-level board setup code for TI DaVinci SoC based boards. - * - * Copyright (C) 2007 Sergey Kubushyn - * - * Partially based on TI sources, original copyrights follow: - */ - -/* - * Board specific setup info - * - * (C) Copyright 2003 - * Texas Instruments, - * Kshitij Gupta - * - * Modified for OMAP 1610 H2 board by Nishant Kamat, Jan 2004 - * - * Modified for OMAP 5912 OSK board by Rishi Bhattacharya, Apr 2004 - * - * Modified for DV-EVM board by Rishi Bhattacharya, Apr 2005 - * - * Modified for DV-EVM board by Swaminathan S, Nov 2005 - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include - -#define MDSTAT_STATE 0x3f - -.globl lowlevel_init -lowlevel_init: -#ifdef CONFIG_SOC_DM644X - - /*-------------------------------------------------------* - * Mask all IRQs by setting all bits in the EINT default * - *-------------------------------------------------------*/ - mov r1, $0 - ldr r0, =EINT_ENABLE0 - str r1, [r0] - ldr r0, =EINT_ENABLE1 - str r1, [r0] - - /*------------------------------------------------------* - * Put the GEM in reset * - *------------------------------------------------------*/ - - /* Put the GEM in reset */ - ldr r8, PSC_GEM_FLAG_CLEAR - ldr r6, MDCTL_GEM - ldr r7, [r6] - and r7, r7, r8 - str r7, [r6] - - /* Enable the Power Domain Transition Command */ - ldr r6, PTCMD - ldr r7, [r6] - orr r7, r7, $0x02 - str r7, [r6] - - /* Check for Transition Complete(PTSTAT) */ -checkStatClkStopGem: - ldr r6, PTSTAT - ldr r7, [r6] - ands r7, r7, $0x02 - bne checkStatClkStopGem - - /* Check for GEM Reset Completion */ -checkGemStatClkStop: - ldr r6, MDSTAT_GEM - ldr r7, [r6] - ands r7, r7, $0x100 - bne checkGemStatClkStop - - /* Do this for enabling a WDT initiated reset this is a workaround - for a chip bug. Not required under normal situations */ - ldr r6, P1394 - mov r10, $0 - str r10, [r6] - - /*------------------------------------------------------* - * Enable L1 & L2 Memories in Fast mode * - *------------------------------------------------------*/ - ldr r6, DFT_ENABLE - mov r10, $0x01 - str r10, [r6] - - ldr r6, MMARG_BRF0 - ldr r10, MMARG_BRF0_VAL - str r10, [r6] - - ldr r6, DFT_ENABLE - mov r10, $0 - str r10, [r6] - - /*------------------------------------------------------* - * DDR2 PLL Initialization * - *------------------------------------------------------*/ - - /* Select the Clock Mode Depending on the Value written in the Boot Table by the run script */ - mov r10, $0 - ldr r6, PLL2_CTL - ldr r7, PLL_CLKSRC_MASK - ldr r8, [r6] - and r8, r8, r7 - mov r9, r10, lsl $8 - orr r8, r8, r9 - str r8, [r6] - - /* Select the PLLEN source */ - ldr r7, PLL_ENSRC_MASK - and r8, r8, r7 - str r8, [r6] - - /* Bypass the PLL */ - ldr r7, PLL_BYPASS_MASK - and r8, r8, r7 - str r8, [r6] - - /* Wait for few cycles to allow PLLEN Mux switch properly to bypass Clock */ - mov r10, $0x20 -WaitPPL2Loop: - subs r10, r10, $1 - bne WaitPPL2Loop - - /* Reset the PLL */ - ldr r7, PLL_RESET_MASK - and r8, r8, r7 - str r8, [r6] - - /* Power up the PLL */ - ldr r7, PLL_PWRUP_MASK - and r8, r8, r7 - str r8, [r6] - - /* Enable the PLL from Disable Mode */ - ldr r7, PLL_DISABLE_ENABLE_MASK - and r8, r8, r7 - str r8, [r6] - - /* Program the PLL Multiplier */ - ldr r6, PLL2_PLLM - mov r2, $0x17 /* 162 MHz */ - str r2, [r6] - - /* Program the PLL2 Divisor Value */ - ldr r6, PLL2_DIV2 - mov r3, $0x01 - str r3, [r6] - - /* Program the PLL2 Divisor Value */ - ldr r6, PLL2_DIV1 - mov r4, $0x0b /* 54 MHz */ - str r4, [r6] - - /* PLL2 DIV2 MMR */ - ldr r8, PLL2_DIV_MASK - ldr r6, PLL2_DIV2 - ldr r9, [r6] - and r8, r8, r9 - mov r9, $0x01 - mov r9, r9, lsl $15 - orr r8, r8, r9 - str r8, [r6] - - /* Program the GOSET bit to take new divider values */ - ldr r6, PLL2_PLLCMD - ldr r7, [r6] - orr r7, r7, $0x01 - str r7, [r6] - - /* Wait for Done */ - ldr r6, PLL2_PLLSTAT -doneLoop_0: - ldr r7, [r6] - ands r7, r7, $0x01 - bne doneLoop_0 - - /* PLL2 DIV1 MMR */ - ldr r8, PLL2_DIV_MASK - ldr r6, PLL2_DIV1 - ldr r9, [r6] - and r8, r8, r9 - mov r9, $0x01 - mov r9, r9, lsl $15 - orr r8, r8, r9 - str r8, [r6] - - /* Program the GOSET bit to take new divider values */ - ldr r6, PLL2_PLLCMD - ldr r7, [r6] - orr r7, r7, $0x01 - str r7, [r6] - - /* Wait for Done */ - ldr r6, PLL2_PLLSTAT -doneLoop: - ldr r7, [r6] - ands r7, r7, $0x01 - bne doneLoop - - /* Wait for PLL to Reset Properly */ - mov r10, $0x218 -ResetPPL2Loop: - subs r10, r10, $1 - bne ResetPPL2Loop - - /* Bring PLL out of Reset */ - ldr r6, PLL2_CTL - ldr r8, [r6] - orr r8, r8, $0x08 - str r8, [r6] - - /* Wait for PLL to Lock */ - ldr r10, PLL_LOCK_COUNT -PLL2Lock: - subs r10, r10, $1 - bne PLL2Lock - - /* Enable the PLL */ - ldr r6, PLL2_CTL - ldr r8, [r6] - orr r8, r8, $0x01 - str r8, [r6] - - /*------------------------------------------------------* - * Issue Soft Reset to DDR Module * - *------------------------------------------------------*/ - - /* Shut down the DDR2 LPSC Module */ - ldr r8, PSC_FLAG_CLEAR - ldr r6, MDCTL_DDR2 - ldr r7, [r6] - and r7, r7, r8 - orr r7, r7, $0x03 - str r7, [r6] - - /* Enable the Power Domain Transition Command */ - ldr r6, PTCMD - ldr r7, [r6] - orr r7, r7, $0x01 - str r7, [r6] - - /* Check for Transition Complete(PTSTAT) */ -checkStatClkStop: - ldr r6, PTSTAT - ldr r7, [r6] - ands r7, r7, $0x01 - bne checkStatClkStop - - /* Check for DDR2 Controller Enable Completion */ -checkDDRStatClkStop: - ldr r6, MDSTAT_DDR2 - ldr r7, [r6] - and r7, r7, $MDSTAT_STATE - cmp r7, $0x03 - bne checkDDRStatClkStop - - /*------------------------------------------------------* - * Program DDR2 MMRs for 162MHz Setting * - *------------------------------------------------------*/ - - /* Program PHY Control Register */ - ldr r6, DDRCTL - ldr r7, DDRCTL_VAL - str r7, [r6] - - /* Program SDRAM Bank Config Register */ - ldr r6, SDCFG - ldr r7, SDCFG_VAL - str r7, [r6] - - /* Program SDRAM TIM-0 Config Register */ - ldr r6, SDTIM0 - ldr r7, SDTIM0_VAL_162MHz - str r7, [r6] - - /* Program SDRAM TIM-1 Config Register */ - ldr r6, SDTIM1 - ldr r7, SDTIM1_VAL_162MHz - str r7, [r6] - - /* Program the SDRAM Bank Config Control Register */ - ldr r10, MASK_VAL - ldr r8, SDCFG - ldr r9, SDCFG_VAL - and r9, r9, r10 - str r9, [r8] - - /* Program SDRAM SDREF Config Register */ - ldr r6, SDREF - ldr r7, SDREF_VAL - str r7, [r6] - - /*------------------------------------------------------* - * Issue Soft Reset to DDR Module * - *------------------------------------------------------*/ - - /* Issue a Dummy DDR2 read/write */ - ldr r8, DDR2_START_ADDR - ldr r7, DUMMY_VAL - str r7, [r8] - ldr r7, [r8] - - /* Shut down the DDR2 LPSC Module */ - ldr r8, PSC_FLAG_CLEAR - ldr r6, MDCTL_DDR2 - ldr r7, [r6] - and r7, r7, r8 - orr r7, r7, $0x01 - str r7, [r6] - - /* Enable the Power Domain Transition Command */ - ldr r6, PTCMD - ldr r7, [r6] - orr r7, r7, $0x01 - str r7, [r6] - - /* Check for Transition Complete(PTSTAT) */ -checkStatClkStop2: - ldr r6, PTSTAT - ldr r7, [r6] - ands r7, r7, $0x01 - bne checkStatClkStop2 - - /* Check for DDR2 Controller Enable Completion */ -checkDDRStatClkStop2: - ldr r6, MDSTAT_DDR2 - ldr r7, [r6] - and r7, r7, $MDSTAT_STATE - cmp r7, $0x01 - bne checkDDRStatClkStop2 - - /*------------------------------------------------------* - * Turn DDR2 Controller Clocks On * - *------------------------------------------------------*/ - - /* Enable the DDR2 LPSC Module */ - ldr r6, MDCTL_DDR2 - ldr r7, [r6] - orr r7, r7, $0x03 - str r7, [r6] - - /* Enable the Power Domain Transition Command */ - ldr r6, PTCMD - ldr r7, [r6] - orr r7, r7, $0x01 - str r7, [r6] - - /* Check for Transition Complete(PTSTAT) */ -checkStatClkEn2: - ldr r6, PTSTAT - ldr r7, [r6] - ands r7, r7, $0x01 - bne checkStatClkEn2 - - /* Check for DDR2 Controller Enable Completion */ -checkDDRStatClkEn2: - ldr r6, MDSTAT_DDR2 - ldr r7, [r6] - and r7, r7, $MDSTAT_STATE - cmp r7, $0x03 - bne checkDDRStatClkEn2 - - /* DDR Writes and Reads */ - ldr r6, CFGTEST - mov r3, $0x01 - str r3, [r6] - - /*------------------------------------------------------* - * System PLL Initialization * - *------------------------------------------------------*/ - - /* Select the Clock Mode Depending on the Value written in the Boot Table by the run script */ - mov r2, $0 - ldr r6, PLL1_CTL - ldr r7, PLL_CLKSRC_MASK - ldr r8, [r6] - and r8, r8, r7 - mov r9, r2, lsl $8 - orr r8, r8, r9 - str r8, [r6] - - /* Select the PLLEN source */ - ldr r7, PLL_ENSRC_MASK - and r8, r8, r7 - str r8, [r6] - - /* Bypass the PLL */ - ldr r7, PLL_BYPASS_MASK - and r8, r8, r7 - str r8, [r6] - - /* Wait for few cycles to allow PLLEN Mux switch properly to bypass Clock */ - mov r10, $0x20 - -WaitLoop: - subs r10, r10, $1 - bne WaitLoop - - /* Reset the PLL */ - ldr r7, PLL_RESET_MASK - and r8, r8, r7 - str r8, [r6] - - /* Disable the PLL */ - orr r8, r8, $0x10 - str r8, [r6] - - /* Power up the PLL */ - ldr r7, PLL_PWRUP_MASK - and r8, r8, r7 - str r8, [r6] - - /* Enable the PLL from Disable Mode */ - ldr r7, PLL_DISABLE_ENABLE_MASK - and r8, r8, r7 - str r8, [r6] - - /* Program the PLL Multiplier */ - ldr r6, PLL1_PLLM - mov r3, $0x15 /* For 594MHz */ - str r3, [r6] - - /* Wait for PLL to Reset Properly */ - mov r10, $0xff - -ResetLoop: - subs r10, r10, $1 - bne ResetLoop - - /* Bring PLL out of Reset */ - ldr r6, PLL1_CTL - orr r8, r8, $0x08 - str r8, [r6] - - /* Wait for PLL to Lock */ - ldr r10, PLL_LOCK_COUNT - -PLL1Lock: - subs r10, r10, $1 - bne PLL1Lock - - /* Enable the PLL */ - orr r8, r8, $0x01 - str r8, [r6] - - nop - nop - nop - nop - - /*------------------------------------------------------* - * AEMIF configuration for NOR Flash (double check) * - *------------------------------------------------------*/ - ldr r0, _PINMUX0 - ldr r1, _DEV_SETTING - str r1, [r0] - - ldr r0, WAITCFG - ldr r1, WAITCFG_VAL - ldr r2, [r0] - orr r2, r2, r1 - str r2, [r0] - - ldr r0, ACFG3 - ldr r1, ACFG3_VAL - ldr r2, [r0] - and r1, r2, r1 - str r1, [r0] - - ldr r0, ACFG4 - ldr r1, ACFG4_VAL - ldr r2, [r0] - and r1, r2, r1 - str r1, [r0] - - ldr r0, ACFG5 - ldr r1, ACFG5_VAL - ldr r2, [r0] - and r1, r2, r1 - str r1, [r0] - - /*--------------------------------------* - * VTP manual Calibration * - *--------------------------------------*/ - ldr r0, VTPIOCR - ldr r1, VTP_MMR0 - str r1, [r0] - - ldr r0, VTPIOCR - ldr r1, VTP_MMR1 - str r1, [r0] - - /* Wait for 33 VTP CLK cycles. VRP operates at 27 MHz */ - ldr r10, VTP_LOCK_COUNT -VTPLock: - subs r10, r10, $1 - bne VTPLock - - ldr r6, DFT_ENABLE - mov r10, $0x01 - str r10, [r6] - - ldr r6, DDRVTPR - ldr r7, [r6] - mov r8, r7, LSL #32-10 - mov r8, r8, LSR #32-10 /* grab low 10 bits */ - ldr r7, VTP_RECAL - orr r8, r7, r8 - ldr r7, VTP_EN - orr r8, r7, r8 - str r8, [r0] - - - /* Wait for 33 VTP CLK cycles. VRP operates at 27 MHz */ - ldr r10, VTP_LOCK_COUNT -VTP1Lock: - subs r10, r10, $1 - bne VTP1Lock - - ldr r1, [r0] - ldr r2, VTP_MASK - and r2, r1, r2 - str r2, [r0] - - ldr r6, DFT_ENABLE - mov r10, $0 - str r10, [r6] - - /* - * Call board-specific lowlevel init. - * That MUST be present and THAT returns - * back to arch calling code with "mov pc, lr." - */ - b dv_board_init - -.ltorg - -_PINMUX0: - .word 0x01c40000 /* Device Configuration Registers */ -_PINMUX1: - .word 0x01c40004 /* Device Configuration Registers */ - -_DEV_SETTING: - .word 0x00000c1f - -WAITCFG: - .word 0x01e00004 -WAITCFG_VAL: - .word 0 -ACFG3: - .word 0x01e00014 -ACFG3_VAL: - .word 0x3ffffffd -ACFG4: - .word 0x01e00018 -ACFG4_VAL: - .word 0x3ffffffd -ACFG5: - .word 0x01e0001c -ACFG5_VAL: - .word 0x3ffffffd - -MDCTL_DDR2: - .word 0x01c41a34 -MDSTAT_DDR2: - .word 0x01c41834 - -PTCMD: - .word 0x01c41120 -PTSTAT: - .word 0x01c41128 - -EINT_ENABLE0: - .word 0x01c48018 -EINT_ENABLE1: - .word 0x01c4801c - -PSC_FLAG_CLEAR: - .word 0xffffffe0 -PSC_GEM_FLAG_CLEAR: - .word 0xfffffeff - -/* DDR2 MMR & CONFIGURATION VALUES, 162 MHZ clock */ -DDRCTL: - .word 0x200000e4 -DDRCTL_VAL: - .word 0x50006405 -SDREF: - .word 0x2000000c -SDREF_VAL: - .word 0x000005c3 -SDCFG: - .word 0x20000008 -SDCFG_VAL: -#ifdef DDR_4BANKS - .word 0x00178622 -#elif defined DDR_8BANKS - .word 0x00178632 -#else -#error "Unknown DDR configuration!!!" -#endif -SDTIM0: - .word 0x20000010 -SDTIM0_VAL_162MHz: - .word 0x28923211 -SDTIM1: - .word 0x20000014 -SDTIM1_VAL_162MHz: - .word 0x0016c722 -VTPIOCR: - .word 0x200000f0 /* VTP IO Control register */ -DDRVTPR: - .word 0x01c42030 /* DDR VPTR MMR */ -VTP_MMR0: - .word 0x201f -VTP_MMR1: - .word 0xa01f -DFT_ENABLE: - .word 0x01c4004c -VTP_LOCK_COUNT: - .word 0x5b0 -VTP_MASK: - .word 0xffffdfff -VTP_RECAL: - .word 0x08000 -VTP_EN: - .word 0x02000 -CFGTEST: - .word 0x80010000 -MASK_VAL: - .word 0x00000fff - -/* GEM Power Up & LPSC Control Register */ -MDCTL_GEM: - .word 0x01c41a9c -MDSTAT_GEM: - .word 0x01c4189c - -/* For WDT reset chip bug */ -P1394: - .word 0x01c41a20 - -PLL_CLKSRC_MASK: - .word 0xfffffeff /* Mask the Clock Mode bit */ -PLL_ENSRC_MASK: - .word 0xffffffdf /* Select the PLLEN source */ -PLL_BYPASS_MASK: - .word 0xfffffffe /* Put the PLL in BYPASS */ -PLL_RESET_MASK: - .word 0xfffffff7 /* Put the PLL in Reset Mode */ -PLL_PWRUP_MASK: - .word 0xfffffffd /* PLL Power up Mask Bit */ -PLL_DISABLE_ENABLE_MASK: - .word 0xffffffef /* Enable the PLL from Disable */ -PLL_LOCK_COUNT: - .word 0x2000 - -/* PLL1-SYSTEM PLL MMRs */ -PLL1_CTL: - .word 0x01c40900 -PLL1_PLLM: - .word 0x01c40910 - -/* PLL2-SYSTEM PLL MMRs */ -PLL2_CTL: - .word 0x01c40d00 -PLL2_PLLM: - .word 0x01c40d10 -PLL2_DIV1: - .word 0x01c40d18 -PLL2_DIV2: - .word 0x01c40d1c -PLL2_PLLCMD: - .word 0x01c40d38 -PLL2_PLLSTAT: - .word 0x01c40d3c -PLL2_DIV_MASK: - .word 0xffff7fff - -MMARG_BRF0: - .word 0x01c42010 /* BRF margin mode 0 (R/W)*/ -MMARG_BRF0_VAL: - .word 0x00444400 - -DDR2_START_ADDR: - .word 0x80000000 -DUMMY_VAL: - .word 0xa55aa55a -#else /* CONFIG_SOC_DM644X */ - mov pc, lr -#endif diff --git a/arch/arm/cpu/arm926ejs/davinci/lxt972.c b/arch/arm/cpu/arm926ejs/davinci/lxt972.c deleted file mode 100644 index c482fd9378..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/lxt972.c +++ /dev/null @@ -1,113 +0,0 @@ -/* - * Intel LXT971/LXT972 PHY Driver for TI DaVinci - * (TMS320DM644x) based boards. - * - * Copyright (C) 2007 Sergey Kubushyn - * - * -------------------------------------------------------- - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include "../../../../../drivers/net/davinci_emac.h" - -#ifdef CONFIG_DRIVER_TI_EMAC - -#ifdef CONFIG_CMD_NET - -int lxt972_is_phy_connected(int phy_addr) -{ - u_int16_t id1, id2; - - if (!davinci_eth_phy_read(phy_addr, MII_PHYSID1, &id1)) - return(0); - if (!davinci_eth_phy_read(phy_addr, MII_PHYSID2, &id2)) - return(0); - - if ((id1 == (0x0013)) && ((id2 & 0xfff0) == 0x78e0)) - return(1); - - return(0); -} - -int lxt972_get_link_speed(int phy_addr) -{ - u_int16_t stat1, tmp; - volatile emac_regs *emac = (emac_regs *)EMAC_BASE_ADDR; - - if (!davinci_eth_phy_read(phy_addr, PHY_LXT971_STAT2, &stat1)) - return(0); - - if (!(stat1 & PHY_LXT971_STAT2_LINK)) /* link up? */ - return(0); - - if (!davinci_eth_phy_read(phy_addr, PHY_LXT971_DIG_CFG, &tmp)) - return(0); - - tmp |= PHY_LXT971_DIG_CFG_MII_DRIVE; - - davinci_eth_phy_write(phy_addr, PHY_LXT971_DIG_CFG, tmp); - /* Read back */ - if (!davinci_eth_phy_read(phy_addr, PHY_LXT971_DIG_CFG, &tmp)) - return(0); - - /* Speed doesn't matter, there is no setting for it in EMAC... */ - if (stat1 & PHY_LXT971_STAT2_DUPLEX_MODE) { - /* set DM644x EMAC for Full Duplex */ - emac->MACCONTROL = EMAC_MACCONTROL_MIIEN_ENABLE | - EMAC_MACCONTROL_FULLDUPLEX_ENABLE; - } else { - /*set DM644x EMAC for Half Duplex */ - emac->MACCONTROL = EMAC_MACCONTROL_MIIEN_ENABLE; - } - - return(1); -} - - -int lxt972_init_phy(int phy_addr) -{ - int ret = 1; - - if (!lxt972_get_link_speed(phy_addr)) { - /* Try another time */ - ret = lxt972_get_link_speed(phy_addr); - } - - /* Disable PHY Interrupts */ - davinci_eth_phy_write(phy_addr, PHY_LXT971_INT_ENABLE, 0); - - return(ret); -} - - -int lxt972_auto_negotiate(int phy_addr) -{ - u_int16_t tmp; - - if (!davinci_eth_phy_read(phy_addr, MII_BMCR, &tmp)) - return(0); - - /* Restart Auto_negotiation */ - tmp |= BMCR_ANRESTART; - davinci_eth_phy_write(phy_addr, MII_BMCR, tmp); - - /*check AutoNegotiate complete */ - udelay (10000); - if (!davinci_eth_phy_read(phy_addr, MII_BMSR, &tmp)) - return(0); - - if (!(tmp & BMSR_ANEGCOMPLETE)) - return(0); - - return (lxt972_get_link_speed(phy_addr)); -} - -#endif /* CONFIG_CMD_NET */ - -#endif /* CONFIG_DRIVER_ETHER */ diff --git a/arch/arm/cpu/arm926ejs/davinci/misc.c b/arch/arm/cpu/arm926ejs/davinci/misc.c deleted file mode 100644 index e18bdfc729..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/misc.c +++ /dev/null @@ -1,138 +0,0 @@ -/* - * Miscelaneous DaVinci functions. - * - * Copyright (C) 2009 Nick Thompson, GE Fanuc Ltd, - * Copyright (C) 2007 Sergey Kubushyn - * Copyright (C) 2008 Lyrtech - * Copyright (C) 2004 Texas Instruments. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -#ifndef CONFIG_SPL_BUILD -int dram_init(void) -{ - /* dram_init must store complete ramsize in gd->ram_size */ - gd->ram_size = get_ram_size( - (void *)CONFIG_SYS_SDRAM_BASE, - CONFIG_MAX_RAM_BANK_SIZE); - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; - gd->bd->bi_dram[0].size = gd->ram_size; -} -#endif - -#ifdef CONFIG_DRIVER_TI_EMAC -/* - * Read ethernet MAC address from EEPROM for DVEVM compatible boards. - * Returns 1 if found, 0 otherwise. - */ -int dvevm_read_mac_address(uint8_t *buf) -{ -#ifdef CONFIG_SYS_I2C_EEPROM_ADDR - /* Read MAC address. */ - if (i2c_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0x7F00, - CONFIG_SYS_I2C_EEPROM_ADDR_LEN, (uint8_t *) &buf[0], 6)) - goto i2cerr; - - /* Check that MAC address is valid. */ - if (!is_valid_ether_addr(buf)) - goto err; - - return 1; /* Found */ - -i2cerr: - printf("Read from EEPROM @ 0x%02x failed\n", - CONFIG_SYS_I2C_EEPROM_ADDR); -err: -#endif /* CONFIG_SYS_I2C_EEPROM_ADDR */ - - return 0; -} - -/* - * Set the mii mode as MII or RMII - */ -#if defined(CONFIG_SOC_DA8XX) -void davinci_emac_mii_mode_sel(int mode_sel) -{ - int val; - - val = readl(&davinci_syscfg_regs->cfgchip3); - if (mode_sel == 0) - val &= ~(1 << 8); - else - val |= (1 << 8); - writel(val, &davinci_syscfg_regs->cfgchip3); -} -#endif -/* - * If there is no MAC address in the environment, then it will be initialized - * (silently) from the value in the EEPROM. - */ -void davinci_sync_env_enetaddr(uint8_t *rom_enetaddr) -{ - uint8_t env_enetaddr[6]; - int ret; - - ret = eth_getenv_enetaddr_by_index("eth", 0, env_enetaddr); - if (!ret) { - /* - * There is no MAC address in the environment, so we - * initialize it from the value in the EEPROM. - */ - debug("### Setting environment from EEPROM MAC address = " - "\"%pM\"\n", - env_enetaddr); - ret = !eth_setenv_enetaddr("ethaddr", rom_enetaddr); - } - if (!ret) - printf("Failed to set mac address from EEPROM: %d\n", ret); -} -#endif /* CONFIG_DRIVER_TI_EMAC */ - -#if defined(CONFIG_SOC_DA8XX) -#ifndef CONFIG_USE_IRQ -void irq_init(void) -{ - /* - * Mask all IRQs by clearing the global enable and setting - * the enable clear for all the 90 interrupts. - */ - writel(0, &davinci_aintc_regs->ger); - - writel(0, &davinci_aintc_regs->hier); - - writel(0xffffffff, &davinci_aintc_regs->ecr1); - writel(0xffffffff, &davinci_aintc_regs->ecr2); - writel(0xffffffff, &davinci_aintc_regs->ecr3); -} -#endif - -/* - * Enable PSC for various peripherals. - */ -int da8xx_configure_lpsc_items(const struct lpsc_resource *item, - const int n_items) -{ - int i; - - for (i = 0; i < n_items; i++) - lpsc_on(item[i].lpsc_no); - - return 0; -} -#endif diff --git a/arch/arm/cpu/arm926ejs/davinci/pinmux.c b/arch/arm/cpu/arm926ejs/davinci/pinmux.c deleted file mode 100644 index e9d8c87cc8..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/pinmux.c +++ /dev/null @@ -1,90 +0,0 @@ -/* - * DaVinci pinmux functions. - * - * Copyright (C) 2009 Nick Thompson, GE Fanuc Ltd, - * Copyright (C) 2007 Sergey Kubushyn - * Copyright (C) 2008 Lyrtech - * Copyright (C) 2004 Texas Instruments. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -/* - * Change the setting of a pin multiplexer field. - * - * Takes an array of pinmux settings similar to: - * - * struct pinmux_config uart_pins[] = { - * { &davinci_syscfg_regs->pinmux[8], 2, 7 }, - * { &davinci_syscfg_regs->pinmux[9], 2, 0 } - * }; - * - * Stepping through the array, each pinmux[n] register has the given value - * set in the pin mux field specified. - * - * The number of pins in the array must be passed (ARRAY_SIZE can provide - * this value conveniently). - * - * Returns 0 if all field numbers and values are in the correct range, - * else returns -1. - */ -int davinci_configure_pin_mux(const struct pinmux_config *pins, - const int n_pins) -{ - int i; - - /* check for invalid pinmux values */ - for (i = 0; i < n_pins; i++) { - if (pins[i].field >= PIN_MUX_NUM_FIELDS || - (pins[i].value & ~PIN_MUX_FIELD_MASK) != 0) - return -1; - } - - /* configure the pinmuxes */ - for (i = 0; i < n_pins; i++) { - const int offset = pins[i].field * PIN_MUX_FIELD_SIZE; - const unsigned int value = pins[i].value << offset; - const unsigned int mask = PIN_MUX_FIELD_MASK << offset; - const dv_reg *mux = pins[i].mux; - - writel(value | (readl(mux) & (~mask)), mux); - } - - return 0; -} - -/* - * Configure multiple pinmux resources. - * - * Takes an pinmux_resource array of pinmux_config and pin counts: - * - * const struct pinmux_resource pinmuxes[] = { - * PINMUX_ITEM(uart_pins), - * PINMUX_ITEM(i2c_pins), - * }; - * - * The number of items in the array must be passed (ARRAY_SIZE can provide - * this value conveniently). - * - * Each item entry is configured in the defined order. If configuration - * of any item fails, -1 is returned and none of the following items are - * configured. On success, 0 is returned. - */ -int davinci_configure_pin_mux_items(const struct pinmux_resource *item, - const int n_items) -{ - int i; - - for (i = 0; i < n_items; i++) { - if (davinci_configure_pin_mux(item[i].pins, - item[i].n_pins) != 0) - return -1; - } - - return 0; -} diff --git a/arch/arm/cpu/arm926ejs/davinci/psc.c b/arch/arm/cpu/arm926ejs/davinci/psc.c deleted file mode 100644 index 8d99e2e997..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/psc.c +++ /dev/null @@ -1,160 +0,0 @@ -/* - * Power and Sleep Controller (PSC) functions. - * - * Copyright (C) 2007 Sergey Kubushyn - * Copyright (C) 2008 Lyrtech - * Copyright (C) 2004 Texas Instruments. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include - -/* - * The PSC manages three inputs to a "module" which may be a peripheral or - * CPU. Those inputs are the module's: clock; reset signal; and sometimes - * its power domain. For our purposes, we only care whether clock and power - * are active, and the module is out of reset. - * - * DaVinci chips may include two separate power domains: "Always On" and "DSP". - * Chips without a DSP generally have only one domain. - * - * The "Always On" power domain is always on when the chip is on, and is - * powered by the VDD pins (on DM644X). The majority of DaVinci modules - * lie within the "Always On" power domain. - * - * A separate domain called the "DSP" domain houses the C64x+ and other video - * hardware such as VICP. In some chips, the "DSP" domain is not always on. - * The "DSP" power domain is powered by the CVDDDSP pins (on DM644X). - */ - -/* Works on Always On power domain only (no PD argument) */ -static void lpsc_transition(unsigned int id, unsigned int state) -{ - dv_reg_p mdstat, mdctl, ptstat, ptcmd; -#ifdef CONFIG_SOC_DA8XX - struct davinci_psc_regs *psc_regs; -#endif - -#ifndef CONFIG_SOC_DA8XX - if (id >= DAVINCI_LPSC_GEM) - return; /* Don't work on DSP Power Domain */ - - mdstat = REG_P(PSC_MDSTAT_BASE + (id * 4)); - mdctl = REG_P(PSC_MDCTL_BASE + (id * 4)); - ptstat = REG_P(PSC_PTSTAT); - ptcmd = REG_P(PSC_PTCMD); -#else - if (id < DAVINCI_LPSC_PSC1_BASE) { - if (id >= PSC_PSC0_MODULE_ID_CNT) - return; - psc_regs = davinci_psc0_regs; - mdstat = &psc_regs->psc0.mdstat[id]; - mdctl = &psc_regs->psc0.mdctl[id]; - } else { - id -= DAVINCI_LPSC_PSC1_BASE; - if (id >= PSC_PSC1_MODULE_ID_CNT) - return; - psc_regs = davinci_psc1_regs; - mdstat = &psc_regs->psc1.mdstat[id]; - mdctl = &psc_regs->psc1.mdctl[id]; - } - ptstat = &psc_regs->ptstat; - ptcmd = &psc_regs->ptcmd; -#endif - - while (readl(ptstat) & 0x01) - continue; - - if ((readl(mdstat) & PSC_MDSTAT_STATE) == state) - return; /* Already in that state */ - - writel((readl(mdctl) & ~PSC_MDCTL_NEXT) | state, mdctl); - - switch (id) { -#ifdef CONFIG_SOC_DM644X - /* Special treatment for some modules as for sprue14 p.7.4.2 */ - case DAVINCI_LPSC_VPSSSLV: - case DAVINCI_LPSC_EMAC: - case DAVINCI_LPSC_EMAC_WRAPPER: - case DAVINCI_LPSC_MDIO: - case DAVINCI_LPSC_USB: - case DAVINCI_LPSC_ATA: - case DAVINCI_LPSC_VLYNQ: - case DAVINCI_LPSC_UHPI: - case DAVINCI_LPSC_DDR_EMIF: - case DAVINCI_LPSC_AEMIF: - case DAVINCI_LPSC_MMC_SD: - case DAVINCI_LPSC_MEMSTICK: - case DAVINCI_LPSC_McBSP: - case DAVINCI_LPSC_GPIO: - writel(readl(mdctl) | 0x200, mdctl); - break; -#endif - } - - writel(0x01, ptcmd); - - while (readl(ptstat) & 0x01) - continue; - while ((readl(mdstat) & PSC_MDSTAT_STATE) != state) - continue; -} - -void lpsc_on(unsigned int id) -{ - lpsc_transition(id, 0x03); -} - -void lpsc_syncreset(unsigned int id) -{ - lpsc_transition(id, 0x01); -} - -void lpsc_disable(unsigned int id) -{ - lpsc_transition(id, 0x0); -} - -/* Not all DaVinci chips have a DSP power domain. */ -#ifdef CONFIG_SOC_DM644X - -/* If DSPLINK is used, we don't want U-Boot to power on the DSP. */ -#if !defined(CONFIG_SYS_USE_DSPLINK) -void dsp_on(void) -{ - int i; - - if (REG(PSC_PDSTAT1) & 0x1f) - return; /* Already on */ - - REG(PSC_GBLCTL) |= 0x01; - REG(PSC_PDCTL1) |= 0x01; - REG(PSC_PDCTL1) &= ~0x100; - REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) |= 0x03; - REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_GEM * 4)) &= 0xfffffeff; - REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) |= 0x03; - REG(PSC_MDCTL_BASE + (DAVINCI_LPSC_IMCOP * 4)) &= 0xfffffeff; - REG(PSC_PTCMD) = 0x02; - - for (i = 0; i < 100; i++) { - if (REG(PSC_EPCPR) & 0x02) - break; - } - - REG(PSC_CHP_SHRTSW) = 0x01; - REG(PSC_PDCTL1) |= 0x100; - REG(PSC_EPCCR) = 0x02; - - for (i = 0; i < 100; i++) { - if (!(REG(PSC_PTSTAT) & 0x02)) - break; - } - - REG(PSC_GBLCTL) &= ~0x1f; -} -#endif /* CONFIG_SYS_USE_DSPLINK */ - -#endif /* have a DSP */ diff --git a/arch/arm/cpu/arm926ejs/davinci/reset.c b/arch/arm/cpu/arm926ejs/davinci/reset.c deleted file mode 100644 index 6b0f15428a..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/reset.c +++ /dev/null @@ -1,32 +0,0 @@ -/* - * Processor reset using WDT. - * - * Copyright (C) 2012 Dmitry Bondar - * Copyright (C) 2007 Sergey Kubushyn - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -void reset_cpu(unsigned long a) -{ - struct davinci_timer *const wdttimer = - (struct davinci_timer *)DAVINCI_WDOG_BASE; - writel(0x08, &wdttimer->tgcr); - writel(readl(&wdttimer->tgcr) | 0x03, &wdttimer->tgcr); - writel(0, &wdttimer->tim12); - writel(0, &wdttimer->tim34); - writel(0, &wdttimer->prd12); - writel(0, &wdttimer->prd34); - writel(readl(&wdttimer->tcr) | 0x40, &wdttimer->tcr); - writel(readl(&wdttimer->wdtcr) | 0x4000, &wdttimer->wdtcr); - writel(0xa5c64000, &wdttimer->wdtcr); - writel(0xda7e4000, &wdttimer->wdtcr); - writel(0x4000, &wdttimer->wdtcr); - while (1) - /*nothing*/; -} diff --git a/arch/arm/cpu/arm926ejs/davinci/spl.c b/arch/arm/cpu/arm926ejs/davinci/spl.c deleted file mode 100644 index 49349da179..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/spl.c +++ /dev/null @@ -1,65 +0,0 @@ -/* - * Copyright (C) 2011 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -#ifndef CONFIG_SPL_LIBCOMMON_SUPPORT -void puts(const char *str) -{ - while (*str) - putc(*str++); -} - -void putc(char c) -{ - if (c == '\n') - NS16550_putc((NS16550_t)(CONFIG_SYS_NS16550_COM1), '\r'); - - NS16550_putc((NS16550_t)(CONFIG_SYS_NS16550_COM1), c); -} -#endif /* CONFIG_SPL_LIBCOMMON_SUPPORT */ - -void spl_board_init(void) -{ -#ifdef CONFIG_SOC_DM365 - dm36x_lowlevel_init(0); -#endif -#ifdef CONFIG_SOC_DA8XX - arch_cpu_init(); -#endif - preloader_console_init(); -} - -u32 spl_boot_mode(void) -{ - return MMCSD_MODE_RAW; -} - -u32 spl_boot_device(void) -{ -#ifdef CONFIG_SPL_NAND_SIMPLE - return BOOT_DEVICE_NAND; -#elif defined(CONFIG_SPL_SPI_LOAD) - return BOOT_DEVICE_SPI; -#elif defined(CONFIG_SPL_MMC_LOAD) - return BOOT_DEVICE_MMC1; -#else - puts("Unknown boot device\n"); - hang(); -#endif -} diff --git a/arch/arm/cpu/arm926ejs/davinci/timer.c b/arch/arm/cpu/arm926ejs/davinci/timer.c deleted file mode 100644 index c7d0652e83..0000000000 --- a/arch/arm/cpu/arm926ejs/davinci/timer.c +++ /dev/null @@ -1,128 +0,0 @@ -/* - * (C) Copyright 2003 - * Texas Instruments - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Marius Groeger - * - * (C) Copyright 2002 - * Sysgo Real-Time Solutions, GmbH - * Alex Zuepke - * - * (C) Copyright 2002-2004 - * Gary Jennejohn, DENX Software Engineering, - * - * (C) Copyright 2004 - * Philippe Robin, ARM Ltd. - * - * Copyright (C) 2007 Sergey Kubushyn - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -static struct davinci_timer * const timer = - (struct davinci_timer *)CONFIG_SYS_TIMERBASE; - -#define TIMER_LOAD_VAL 0xffffffff - -#define TIM_CLK_DIV 16 - -int timer_init(void) -{ - /* We are using timer34 in unchained 32-bit mode, full speed */ - writel(0x0, &timer->tcr); - writel(0x0, &timer->tgcr); - writel(0x06 | ((TIM_CLK_DIV - 1) << 8), &timer->tgcr); - writel(0x0, &timer->tim34); - writel(TIMER_LOAD_VAL, &timer->prd34); - writel(2 << 22, &timer->tcr); - gd->arch.timer_rate_hz = CONFIG_SYS_HZ_CLOCK / TIM_CLK_DIV; - gd->arch.timer_reset_value = 0; - - return(0); -} - -/* - * Get the current 64 bit timer tick count - */ -unsigned long long get_ticks(void) -{ - unsigned long now = readl(&timer->tim34); - - /* increment tbu if tbl has rolled over */ - if (now < gd->arch.tbl) - gd->arch.tbu++; - gd->arch.tbl = now; - - return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl; -} - -ulong get_timer(ulong base) -{ - unsigned long long timer_diff; - - timer_diff = get_ticks() - gd->arch.timer_reset_value; - - return lldiv(timer_diff, - (gd->arch.timer_rate_hz / CONFIG_SYS_HZ)) - base; -} - -void __udelay(unsigned long usec) -{ - unsigned long long endtime; - - endtime = lldiv((unsigned long long)usec * gd->arch.timer_rate_hz, - 1000000UL); - endtime += get_ticks(); - - while (get_ticks() < endtime) - ; -} - -/* - * This function is derived from PowerPC code (timebase clock frequency). - * On ARM it returns the number of timer ticks per second. - */ -ulong get_tbclk(void) -{ - return gd->arch.timer_rate_hz; -} - -#ifdef CONFIG_HW_WATCHDOG -static struct davinci_timer * const wdttimer = - (struct davinci_timer *)CONFIG_SYS_WDTTIMERBASE; - -/* - * See prufw2.pdf for using Timer as a WDT - */ -void davinci_hw_watchdog_enable(void) -{ - writel(0x0, &wdttimer->tcr); - writel(0x0, &wdttimer->tgcr); - /* TIMMODE = 2h */ - writel(0x08 | 0x03 | ((TIM_CLK_DIV - 1) << 8), &wdttimer->tgcr); - writel(CONFIG_SYS_WDT_PERIOD_LOW, &wdttimer->prd12); - writel(CONFIG_SYS_WDT_PERIOD_HIGH, &wdttimer->prd34); - writel(2 << 22, &wdttimer->tcr); - writel(0x0, &wdttimer->tim12); - writel(0x0, &wdttimer->tim34); - /* set WDEN bit, WDKEY 0xa5c6 */ - writel(0xa5c64000, &wdttimer->wdtcr); - /* clear counter register */ - writel(0xda7e4000, &wdttimer->wdtcr); -} - -void davinci_hw_watchdog_reset(void) -{ - writel(0xa5c64000, &wdttimer->wdtcr); - writel(0xda7e4000, &wdttimer->wdtcr); -} -#endif -- cgit v1.2.1