From 5434caf5ba32d0779f309d7a8d13e985dc667f5b Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Sun, 16 Jun 2013 15:39:02 +0200 Subject: ARM: mxs: Consolidate configuration options Pull all the duplicate configuration options into configs/mxs.h from the board configuration files. This reduces the files greatly and makes them somewhat more readable. Besides, we do no longer have such a horrible duplication of code. Note that the mx23evk grew in size slightly. This is due to the CONFIG_SYS_CBSIZE now being set to 1024 as it is on the rest of MXS systems. This patch also fixes the OCRAM size for i.MX23. The i.MX23 has only 32kB of OCRAM, while i.MX28 has 128kB of OCRAM. I verified the configuration didn't change for each of the boards, but I didn't boot-test it on the boards I do not have. I configured U-Boot for each board using the "make ... _config" command and then ran "cpp -I include -dM include/config.h" , which dumped all the configuration options. I did this both before and after this patch and finally compared the results for each MXS board. Actually, the results do differ slightly, since the configs/mxs.h file now properly includes the correct iomux-mx23.h or iomux-mx28.h , so while comparing, I had to ignore these new defines. These have no impact on U-Boot configuration though. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: Lauri Hintsala Cc: Otavio Salvador Cc: Stefano Babic --- include/configs/apx4devkit.h | 120 ++++-------------------- include/configs/m28evk.h | 192 ++++++--------------------------------- include/configs/mx23_olinuxino.h | 142 +++++------------------------ include/configs/mx23evk.h | 115 ++++------------------- include/configs/mx28evk.h | 173 +++++++++-------------------------- include/configs/mxs.h | 191 ++++++++++++++++++++++++++++++++++++++ include/configs/sc_sps_1.h | 139 ++++------------------------ 7 files changed, 340 insertions(+), 732 deletions(-) create mode 100644 include/configs/mxs.h diff --git a/include/configs/apx4devkit.h b/include/configs/apx4devkit.h index 32421339d5..7081f3769e 100644 --- a/include/configs/apx4devkit.h +++ b/include/configs/apx4devkit.h @@ -19,34 +19,16 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ -#ifndef __CONFIG_H -#define __CONFIG_H +#ifndef __CONFIGS_APX4DEVKIT_H__ +#define __CONFIGS_APX4DEVKIT_H__ -/* SoC configurations */ +/* System configurations */ #define CONFIG_MX28 /* i.MX28 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - #define MACH_TYPE_APX4DEVKIT 3712 #define CONFIG_MACH_TYPE MACH_TYPE_APX4DEVKIT -#include - -#define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_CPU_INIT -#define CONFIG_ARCH_MISC_INIT - -/* SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - /* U-Boot Commands */ +#define CONFIG_SYS_NO_FLASH #include #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -66,78 +48,26 @@ #define CONFIG_CMD_SAVEENV #define CONFIG_CMD_USB -/* Memory configurations */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 +/* Environment */ #define CONFIG_ENV_OVERWRITE - -/* U-Boot general configurations */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-Boot version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc. */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " -#define CONFIG_OF_LIBFDT #define CONFIG_ENV_IS_IN_NAND -/* Serial Driver */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* DMA */ -#define CONFIG_APBH_DMA - -/* MMC Driver */ -#ifdef CONFIG_ENV_IS_IN_MMC +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) #define CONFIG_ENV_OFFSET (256 * 1024) #define CONFIG_ENV_SIZE (16 * 1024) #define CONFIG_SYS_MMC_ENV_DEV 0 #endif -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_MXS_MMC -#endif - -/* NAND Driver */ -#ifdef CONFIG_ENV_IS_IN_NAND +/* Environment is in NAND */ +#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND) #define CONFIG_ENV_SECT_SIZE (128 * 1024) #define CONFIG_ENV_SIZE (128 * 1024) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE @@ -147,12 +77,8 @@ (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) #endif +/* UBI and NAND partitioning */ #ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_MXS -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x60000000 -#define CONFIG_SYS_NAND_5_ADDR_CYCLE - #define CONFIG_CMD_UBI #define CONFIG_CMD_UBIFS #define CONFIG_CMD_MTDPARTS @@ -167,43 +93,30 @@ #define MTDPARTS_DEFAULT "" #endif -/* Ethernet on SOC (FEC) */ +/* FEC Ethernet on SoC */ #ifdef CONFIG_CMD_NET +#define CONFIG_FEC_MXC #define CONFIG_NET_MULTI #define CONFIG_ETHPRIME "FEC" -#define CONFIG_FEC_MXC #define CONFIG_FEC_MXC_PHYADDR 0 #define IMX_FEC_BASE MXS_ENET0_BASE -#define CONFIG_MII -#define CONFIG_FEC_XCV_TYPE RMII #endif /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT1 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif -/* I2C */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MXS -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#endif /* RTC */ -#if defined(CONFIG_CMD_DATE) +#ifdef CONFIG_CMD_DATE #define CONFIG_RTC_PCF8563 #define CONFIG_SYS_I2C_RTC_ADDR 0x51 #endif /* Boot Linux */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTDELAY 1 #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTCOMMAND "run bootcmd_nand" @@ -233,4 +146,7 @@ "ext2load mmc 0:2 41000000 boot/uImage && bootm 41000000\0" \ "" -#endif /* __CONFIG_H */ +/* The rest of the configuration is shared */ +#include + +#endif /* __CONFIGS_APX4DEVKIT_H__ */ diff --git a/include/configs/m28evk.h b/include/configs/m28evk.h index 10ccc3bc37..b6fa6ebb3f 100644 --- a/include/configs/m28evk.h +++ b/include/configs/m28evk.h @@ -17,43 +17,17 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ -#ifndef __M28EVK_CONFIG_H__ -#define __M28EVK_CONFIG_H__ +#ifndef __CONFIGS_M28EVK_H__ +#define __CONFIGS_M28EVK_H__ -/* - * SoC configurations - */ -#define CONFIG_MX28 /* i.MX28 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ -/* - * Define M28EVK machine type by hand until it lands in mach-types - */ +/* System configurations */ +#define CONFIG_MX28 /* i.MX28 SoC */ #define MACH_TYPE_M28EVK 3613 - #define CONFIG_MACH_TYPE MACH_TYPE_M28EVK -#include - +/* U-Boot Commands */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT - -/* - * SPL - */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - -/* - * U-Boot Commands - */ #include #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -82,86 +56,18 @@ #define CONFIG_REGEX /* Enable regular expression support */ -/* - * Memory configurations - */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x20000000 /* Max 512 MB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 - -/* - * U-Boot general configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER - -/* - * Serial Driver - */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ - -/* - * MMC Driver - */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_GENERIC_MMC -#define CONFIG_MXS_MMC -#endif -/* - * APBH DMA - */ -#define CONFIG_APBH_DMA - -/* - * NAND - */ +/* Environment */ #define CONFIG_ENV_SIZE (16 * 1024) -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_MXS -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x60000000 -#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#define CONFIG_ENV_IS_IN_NAND /* Environment is in NAND */ -#define CONFIG_ENV_IS_IN_NAND +#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE #define CONFIG_ENV_SECT_SIZE (128 * 1024) #define CONFIG_ENV_RANGE (512 * 1024) @@ -190,40 +96,22 @@ #define CONFIG_ENV_IS_NOWHERE #endif -/* - * Ethernet on SOC (FEC) - */ -#ifdef CONFIG_CMD_NET -#define CONFIG_ETHPRIME "FEC0" +/* FEC Ethernet on SoC */ +#ifdef CONFIG_CMD_NET #define CONFIG_FEC_MXC -#define CONFIG_MII -#define CONFIG_FEC_XCV_TYPE RMII #endif -/* - * I2C - */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MXS -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#endif - -/* - * EEPROM - */ -#ifdef CONFIG_CMD_EEPROM +/* EEPROM */ +#ifdef CONFIG_CMD_EEPROM #define CONFIG_SYS_I2C_MULTI_EEPROMS #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 #endif -/* - * RTC - */ -#ifdef CONFIG_CMD_DATE +/* RTC */ +#ifdef CONFIG_CMD_DATE /* Use the internal RTC in the MXS chip */ #define CONFIG_RTC_INTERNAL -#ifdef CONFIG_RTC_INTERNAL +#ifdef CONFIG_RTC_INTERNAL #define CONFIG_RTC_MXS #else #define CONFIG_RTC_M41T62 @@ -232,32 +120,22 @@ #endif #endif -/* - * USB - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS +/* USB */ +#ifdef CONFIG_CMD_USB #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_EHCI_MXS_PORT1 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif -/* - * SPI - */ -#ifdef CONFIG_CMD_SPI -#define CONFIG_HARD_SPI -#define CONFIG_MXS_SPI -#define CONFIG_SPI_HALF_DUPLEX +/* SPI */ +#ifdef CONFIG_CMD_SPI #define CONFIG_DEFAULT_SPI_BUS 2 #define CONFIG_DEFAULT_SPI_CS 0 #define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0 /* SPI FLASH */ -#ifdef CONFIG_CMD_SF +#ifdef CONFIG_CMD_SF #define CONFIG_SPI_FLASH #define CONFIG_SPI_FLASH_STMICRO #define CONFIG_SF_DEFAULT_BUS 2 @@ -270,18 +148,12 @@ #define CONFIG_ENV_SPI_MAX_HZ 40000000 #define CONFIG_ENV_SPI_MODE SPI_MODE_0 #endif + #endif -/* - * LCD - */ -#ifdef CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_MXS +/* LCD */ +#ifdef CONFIG_VIDEO #define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV #define CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP @@ -290,22 +162,15 @@ #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10) #endif -/* - * Boot Linux - */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS +/* Booting Linux */ #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTARGS "console=ttyAMA0,115200n8 " #define CONFIG_BOOTCOMMAND "run bootcmd_net" #define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT -/* - * Extra Environments - */ +/* Extra Environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_nand_full_filename=u-boot.nand\0" \ "update_nand_firmware_filename=u-boot.sb\0" \ @@ -346,4 +211,7 @@ "fi ; " \ "fi\0" -#endif /* __M28EVK_CONFIG_H__ */ +/* The rest of the configuration is shared */ +#include + +#endif /* __CONFIGS_M28EVK_H__ */ diff --git a/include/configs/mx23_olinuxino.h b/include/configs/mx23_olinuxino.h index 38ad7f4d8f..418d4fd948 100644 --- a/include/configs/mx23_olinuxino.h +++ b/include/configs/mx23_olinuxino.h @@ -16,40 +16,15 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ -#ifndef __MX23_OLINUXINO_CONFIG_H__ -#define __MX23_OLINUXINO_CONFIG_H__ +#ifndef __CONFIGS_MX23_OLINUXINO_H__ +#define __CONFIGS_MX23_OLINUXINO_H__ -#include - -/* - * SoC configurations - */ +/* System configurations */ #define CONFIG_MX23 /* i.MX23 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - #define CONFIG_MACH_TYPE 4105 -#include - +/* U-Boot Commands */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT - -/* - * SPL - */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - -/* - * U-Boot Commands - */ #include #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -64,92 +39,36 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_USB -/* - * Memory configurations - */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 -/* - * U-Boot general configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER +/* Environment */ +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OVERWRITE -/* - * Serial Driver - */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) +#define CONFIG_ENV_OFFSET (256 * 1024) +#define CONFIG_ENV_SIZE (16 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 +#endif -/* - * Status LED - */ +/* Status LED */ #define CONFIG_STATUS_LED #define CONFIG_GPIO_LED #define CONFIG_BOARD_SPECIFIC_LED -#define STATUS_LED_BOOT 0 -#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1 +#define STATUS_LED_BOOT 0 +#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1 #define STATUS_LED_STATE STATUS_LED_ON #define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) -/* - * MMC Driver - */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_GENERIC_MMC -#define CONFIG_MXS_MMC -#endif - -/* - * APBH DMA - */ -#define CONFIG_APBH_DMA - /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif @@ -159,31 +78,13 @@ #define CONFIG_USB_ETHER_SMSC95XX #endif -/* - * Boot Linux - */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS +/* Booting Linux */ #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTFILE "uImage" #define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT -/* - * Environment - */ -#define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OVERWRITE -#ifdef CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET (256 * 1024) -#define CONFIG_ENV_SIZE (16 * 1024) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#endif - -/* - * Extra Environments - */ +/* Extra Environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_sd_firmware_filename=u-boot.sd\0" \ "update_sd_firmware=" /* Update the SD firmware partition */ \ @@ -265,4 +166,7 @@ "fi; " \ "else run netboot; fi" -#endif /* __MX23_OLINUXINO_CONFIG_H__ */ +/* The rest of the configuration is shared */ +#include + +#endif /* __CONFIGS_MX23_OLINUXINO_H__ */ diff --git a/include/configs/mx23evk.h b/include/configs/mx23evk.h index 3a58afee9a..b52b9e68e0 100644 --- a/include/configs/mx23evk.h +++ b/include/configs/mx23evk.h @@ -19,33 +19,15 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA * */ -#ifndef __MX23EVK_CONFIG_H__ -#define __MX23EVK_CONFIG_H__ +#ifndef __CONFIGS_MX23EVK_H__ +#define __CONFIGS_MX23EVK_H__ -/* SoC configurations */ +/* System configurations */ #define CONFIG_MX23 /* i.MX23 SoC */ - -#include - -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - #define CONFIG_MACH_TYPE MACH_TYPE_MX23EVK -#define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT - -/* SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - /* U-Boot Commands */ +#define CONFIG_SYS_NO_FLASH #include #undef CONFIG_CMD_NET #undef CONFIG_CMD_NFS @@ -62,86 +44,33 @@ #define CONFIG_CMD_BOOTZ #define CONFIG_VIDEO -/* Memory configurations */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */ -#define CONFIG_STACKSIZE (128 * 1024) /* 128 KB stack */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 +/* Environment */ #define CONFIG_ENV_OVERWRITE +#define CONFIG_ENV_IS_IN_MMC -/* U-Boot general configurations */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 256 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " - -/* Serial Driver */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ - -/* DMA */ -#define CONFIG_APBH_DMA - -/* MMC Driver */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_MXS_MMC +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) +#define CONFIG_ENV_OFFSET (256 * 1024) +#define CONFIG_ENV_SIZE (16 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 #endif /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif /* Framebuffer support */ #ifdef CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_MXS #define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV #define CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP @@ -151,21 +80,10 @@ #endif /* Boot Linux */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTDELAY 1 -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_LOADADDR 0x42000000 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT - -/* Environment */ -#define CONFIG_ENV_IS_IN_MMC -#ifdef CONFIG_ENV_IS_IN_MMC - #define CONFIG_ENV_OFFSET (256 * 1024) - #define CONFIG_ENV_SIZE (16 * 1024) - #define CONFIG_SYS_MMC_ENV_DEV 0 -#endif /* Extra Environments */ #define CONFIG_EXTRA_ENV_SETTINGS \ @@ -224,4 +142,7 @@ "fi; " \ "else exit; fi" -#endif /* __MX23EVK_CONFIG_H__ */ +/* The rest of the configuration is shared */ +#include + +#endif /* __CONFIGS_MX23EVK_H__ */ diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h index de69182b4f..877b811052 100644 --- a/include/configs/mx28evk.h +++ b/include/configs/mx28evk.h @@ -16,33 +16,16 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. */ -#ifndef __MX28EVK_CONFIG_H__ -#define __MX28EVK_CONFIG_H__ +#ifndef __CONFIGS_MX28EVK_H__ +#define __CONFIGS_MX28EVK_H__ -/* SoC configurations */ +/* System configurations */ #define CONFIG_MX28 /* i.MX28 SoC */ - -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - #define CONFIG_MACH_TYPE MACH_TYPE_MX28EVK - -#include - -#define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT - -/* SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > " /* U-Boot Commands */ +#define CONFIG_SYS_NO_FLASH #include #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -57,6 +40,7 @@ #define CONFIG_CMD_NET #define CONFIG_CMD_NFS #define CONFIG_CMD_PING +#define CONFIG_CMD_SAVEENV #define CONFIG_CMD_SETEXPR #define CONFIG_CMD_SF #define CONFIG_CMD_SPI @@ -66,81 +50,24 @@ #define CONFIG_CMD_NAND_TRIMFFS #define CONFIG_VIDEO -/* Memory configurations */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ - -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 +/* Environment */ +#define CONFIG_ENV_SIZE (16 * 1024) #define CONFIG_ENV_OVERWRITE -/* U-Boot general configurations */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "MX28EVK U-Boot > " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER - -/* Serial Driver */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ -/* DMA */ -#define CONFIG_APBH_DMA - -/* MMC Driver */ -#ifdef CONFIG_ENV_IS_IN_MMC - #define CONFIG_ENV_OFFSET (256 * 1024) - #define CONFIG_ENV_SIZE (16 * 1024) - #define CONFIG_SYS_MMC_ENV_DEV 0 -#endif -#define CONFIG_CMD_SAVEENV -#ifdef CONFIG_CMD_MMC -#define CONFIG_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_MXS_MMC +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) +#define CONFIG_ENV_OFFSET (256 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 #endif -/* NAND Driver */ -#define CONFIG_ENV_SIZE (16 * 1024) -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_MXS -#define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define CONFIG_SYS_NAND_BASE 0x60000000 -#define CONFIG_SYS_NAND_5_ADDR_CYCLE - /* Environment is in NAND */ -#ifdef CONFIG_ENV_IS_IN_NAND +#if defined(CONFIG_CMD_NAND) && defined(CONFIG_ENV_IS_IN_NAND) #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE #define CONFIG_ENV_SECT_SIZE (128 * 1024) #define CONFIG_ENV_RANGE (512 * 1024) @@ -149,6 +76,21 @@ (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) #endif +/* Environemnt is in SPI flash */ +#if defined(CONFIG_CMD_SF) && defined(CONFIG_ENV_IS_IN_SPI_FLASH) +#define CONFIG_SYS_REDUNDAND_ENVIRONMENT +#define CONFIG_ENV_SIZE 0x1000 /* 4KB */ +#define CONFIG_ENV_OFFSET 0x40000 /* 256K */ +#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) +#define CONFIG_ENV_SECT_SIZE 0x1000 +#define CONFIG_ENV_SPI_CS 0 +#define CONFIG_ENV_SPI_BUS 2 +#define CONFIG_ENV_SPI_MAX_HZ 24000000 +#define CONFIG_ENV_SPI_MODE SPI_MODE_0 +#endif + +/* UBI and NAND partitioning */ +#ifdef CONFIG_CMD_NAND #define CONFIG_CMD_UBI #define CONFIG_CMD_UBIFS #define CONFIG_CMD_MTDPARTS @@ -168,13 +110,10 @@ "-(filesystem)" #endif -/* Ethernet on SOC (FEC) */ +/* FEC Ethernet on SoC */ #ifdef CONFIG_CMD_NET -#define CONFIG_NET_MULTI -#define CONFIG_ETHPRIME "FEC0" #define CONFIG_FEC_MXC -#define CONFIG_MII -#define CONFIG_FEC_XCV_TYPE RMII +#define CONFIG_NET_MULTI #define CONFIG_MX28_FEC_MAC_IN_OCOTP #endif @@ -185,65 +124,35 @@ /* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT1 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #define CONFIG_USB_HOST_ETHER #define CONFIG_USB_ETHER_ASIX #define CONFIG_USB_ETHER_SMSC95XX #endif -/* I2C */ -#ifdef CONFIG_CMD_I2C -#define CONFIG_I2C_MXS -#define CONFIG_HARD_I2C -#define CONFIG_SYS_I2C_SPEED 400000 -#endif - /* SPI */ #ifdef CONFIG_CMD_SPI -#define CONFIG_HARD_SPI -#define CONFIG_MXS_SPI -#define CONFIG_SPI_HALF_DUPLEX #define CONFIG_DEFAULT_SPI_BUS 2 #define CONFIG_DEFAULT_SPI_MODE SPI_MODE_0 /* SPI Flash */ #ifdef CONFIG_CMD_SF #define CONFIG_SPI_FLASH -#define CONFIG_SF_DEFAULT_BUS 2 -#define CONFIG_SF_DEFAULT_CS 0 +#define CONFIG_SF_DEFAULT_BUS 2 +#define CONFIG_SF_DEFAULT_CS 0 /* this may vary and depends on the installed chip */ #define CONFIG_SPI_FLASH_SST #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 #define CONFIG_SF_DEFAULT_SPEED 24000000 - -/* (redundant) environemnt in SPI flash */ -#ifdef CONFIG_ENV_IS_IN_SPI_FLASH -#define CONFIG_SYS_REDUNDAND_ENVIRONMENT -#define CONFIG_ENV_SIZE 0x1000 /* 4KB */ -#define CONFIG_ENV_OFFSET 0x40000 /* 256K */ -#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) -#define CONFIG_ENV_SECT_SIZE 0x1000 -#define CONFIG_ENV_SPI_CS 0 -#define CONFIG_ENV_SPI_BUS 2 -#define CONFIG_ENV_SPI_MAX_HZ 24000000 -#define CONFIG_ENV_SPI_MODE SPI_MODE_0 -#endif #endif + #endif /* Framebuffer support */ #ifdef CONFIG_VIDEO -#define CONFIG_CFB_CONSOLE -#define CONFIG_VIDEO_MXS #define CONFIG_VIDEO_LOGO -#define CONFIG_VIDEO_SW_CURSOR -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV #define CONFIG_SPLASH_SCREEN #define CONFIG_CMD_BMP #define CONFIG_BMP_16BPP @@ -253,15 +162,12 @@ #endif /* Boot Linux */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTDELAY 1 -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_LOADADDR 0x42000000 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT -/* Extra Environments */ +/* Extra Environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_nand_full_filename=u-boot.nand\0" \ "update_nand_firmware_filename=u-boot.sb\0" \ @@ -372,4 +278,7 @@ "fi; " \ "else run netboot; fi" -#endif /* __MX28EVK_CONFIG_H__ */ +/* The rest of the configuration is shared */ +#include + +#endif /* __CONFIGS_MX28EVK_H__ */ diff --git a/include/configs/mxs.h b/include/configs/mxs.h new file mode 100644 index 0000000000..a684166502 --- /dev/null +++ b/include/configs/mxs.h @@ -0,0 +1,191 @@ +/* + * Copyright (C) 2013 Marek Vasut + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#ifndef __CONFIGS_MXS_H__ +#define __CONFIGS_MXS_H__ + +/* + * Includes + */ + +#if defined(CONFIG_MX23) && defined(CONFIG_MX28) +#error Select either CONFIG_MX23 or CONFIG_MX28 , never both! +#elif !defined(CONFIG_MX23) && !defined(CONFIG_MX28) +#error Select one of CONFIG_MX23 or CONFIG_MX28 ! +#endif + +#include + +#if defined(CONFIG_MX23) +#include +#elif defined(CONFIG_MX28) +#include +#endif + +/* + * CPU specifics + */ + +/* Ticks per second */ +#define CONFIG_SYS_HZ 1000 + +/* MXS uses FDT */ +#define CONFIG_OF_LIBFDT + +/* Startup hooks */ +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_ARCH_MISC_INIT + +/* SPL */ +#define CONFIG_SPL +#define CONFIG_SPL_NO_CPU_SUPPORT_CODE +#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT + +/* Memory sizes */ +#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ +#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ +#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ + +/* OCRAM at 0x0 ; 32kB on MX23 ; 128kB on MX28 */ +#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 +#if defined(CONFIG_MX23) +#define CONFIG_SYS_INIT_RAM_SIZE (32 * 1024) +#elif defined(CONFIG_MX28) +#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) +#endif + +/* Point initial SP in SRAM so SPL can use it too. */ +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* + * We need to sacrifice first 4 bytes of RAM here to avoid triggering some + * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot + * binary. In case there was more of this mess, 0x100 bytes are skipped. + */ +#define CONFIG_SYS_TEXT_BASE 0x40000100 + +/* U-Boot general configuration */ +#define CONFIG_SYS_LONGHELP +#ifndef CONFIG_SYS_PROMPT +#define CONFIG_SYS_PROMPT "=> " +#endif +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ +#define CONFIG_SYS_PBSIZE \ + (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) + /* Print buffer size */ +#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + /* Boot argument buffer size */ +#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ +#define CONFIG_AUTO_COMPLETE /* Command auto complete */ +#define CONFIG_CMDLINE_EDITING /* Command history etc */ +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " + +/* Booting Linux */ +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS + +/* + * Drivers + */ + +/* APBH DMA */ +#define CONFIG_APBH_DMA + +/* GPIO */ +#define CONFIG_MXS_GPIO + +/* DUART Serial Driver */ +#define CONFIG_PL011_SERIAL +#define CONFIG_PL011_CLOCK 24000000 +#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } +#define CONFIG_CONS_INDEX 0 +/* Default baudrate can be overriden by board! */ +#ifndef CONFIG_BAUDRATE +#define CONFIG_BAUDRATE 115200 +#endif + +/* FEC Ethernet on SoC */ +#ifdef CONFIG_FEC_MXC +#define CONFIG_MII +#ifndef CONFIG_ETHPRIME +#define CONFIG_ETHPRIME "FEC0" +#endif +#ifndef CONFIG_FEC_XCV_TYPE +#define CONFIG_FEC_XCV_TYPE RMII +#endif +#endif + +/* I2C */ +#ifdef CONFIG_CMD_I2C +#define CONFIG_I2C_MXS +#define CONFIG_HARD_I2C +#ifndef CONFIG_SYS_I2C_SPEED +#define CONFIG_SYS_I2C_SPEED 400000 +#endif +#endif + +/* LCD */ +#ifdef CONFIG_VIDEO +#define CONFIG_CFB_CONSOLE +#define CONFIG_VIDEO_MXS +#define CONFIG_VIDEO_SW_CURSOR +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#endif + +/* MMC */ +#ifdef CONFIG_CMD_MMC +#define CONFIG_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_BOUNCE_BUFFER +#define CONFIG_MXS_MMC +#endif + +/* NAND */ +#ifdef CONFIG_CMD_NAND +#define CONFIG_NAND_MXS +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_SYS_NAND_BASE 0x60000000 +#define CONFIG_SYS_NAND_5_ADDR_CYCLE +#endif + +/* SPI */ +#ifdef CONFIG_CMD_SPI +#define CONFIG_HARD_SPI +#define CONFIG_MXS_SPI +#define CONFIG_SPI_HALF_DUPLEX +#endif + +/* USB */ +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MXS +#define CONFIG_EHCI_IS_TDI +#endif + +#endif /* __CONFIGS_MXS_H__ */ diff --git a/include/configs/sc_sps_1.h b/include/configs/sc_sps_1.h index 349497f67a..b7b46b4a50 100644 --- a/include/configs/sc_sps_1.h +++ b/include/configs/sc_sps_1.h @@ -19,48 +19,16 @@ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, * MA 02111-1307 USA */ -#ifndef __SC_SPS_1_H__ -#define __SC_SPS_1_H__ +#ifndef __CONFIGS_SC_SPS_1_H__ +#define __CONFIGS_SC_SPS_1_H__ -/* - * SoC configurations - */ +/* System configuration */ #define CONFIG_MX28 /* i.MX28 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ - -/* - * Define SC_SPS_1 machine type by hand until it lands in mach-types - */ #define MACH_TYPE_SC_SPS_1 4172 - #define CONFIG_MACH_TYPE MACH_TYPE_SC_SPS_1 -#include - +/* U-Boot Commands */ #define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_CPU_INIT -#define CONFIG_ARCH_MISC_INIT - -#define CONFIG_ENV_IS_IN_MMC - -#define CONFIG_OF_LIBFDT - -/* - * SPL - */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT - -/* - * U-Boot Commands - */ #include #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -78,119 +46,47 @@ #define CONFIG_CMD_SETEXPR #define CONFIG_CMD_USB -/* - * Memory configurations - */ +/* Memory configuration */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */ -#define CONFIG_STACKSIZE 0x00010000 /* 128 KB stack */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ #define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -/* Point initial SP in SRAM so SPL can use it too. */ -#define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 -#define CONFIG_SYS_INIT_RAM_SIZE (128 * 1024) - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) -/* - * We need to sacrifice first 4 bytes of RAM here to avoid triggering some - * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot - * binary. In case there was more of this mess, 0x100 bytes are skipped. - */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 - -/* - * U-Boot general configurations - */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ - (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) - /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT_HUSH_PS2 "> " - -/* - * Serial Driver - */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } - -/* - * MMC Driver - */ -#ifdef CONFIG_CMD_MMC -#define CONFIG_APBH_DMA -#define CONFIG_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_GENERIC_MMC -#define CONFIG_MXS_MMC -#endif +/* Environment */ #define CONFIG_ENV_SIZE (16 * 1024) -#ifdef CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_IS_IN_MMC + +/* Environment is in MMC */ +#if defined(CONFIG_CMD_MMC) && defined(CONFIG_ENV_IS_IN_MMC) #define CONFIG_ENV_OFFSET (256 * 1024) #define CONFIG_SYS_MMC_ENV_DEV 0 #else #define CONFIG_ENV_IS_NOWHERE #endif -/* - * Ethernet on SOC (FEC) - */ +/* FEC Ethernet on SoC */ #ifdef CONFIG_CMD_NET -#define CONFIG_ETHPRIME "FEC0" #define CONFIG_FEC_MXC -#define CONFIG_MII -#define CONFIG_FEC_XCV_TYPE RMII #define CONFIG_PHYLIB #define CONFIG_PHY_SMSC #endif -/* - * USB - */ +/* USB */ #ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS #define CONFIG_EHCI_MXS_PORT0 #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI #define CONFIG_USB_STORAGE #endif -/* - * Boot Linux - */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS +/* Booting Linux */ #define CONFIG_BOOTDELAY 3 #define CONFIG_BOOTFILE "uImage" #define CONFIG_BOOTARGS "console=ttyAMA0,115200" -#define CONFIG_BOOTCOMMAND "bootm " +#define CONFIG_BOOTCOMMAND "bootm" #define CONFIG_LOADADDR 0x42000000 #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -/* - * Extra Environments - */ +/* Extra Environment */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_sd_firmware_filename=u-boot.sd\0" \ "update_sd_firmware=" /* Update the SD firmware partition */ \ @@ -202,4 +98,7 @@ "fi ; " \ "fi\0" -#endif /* __SC_SPS_1_H__ */ +/* The rest of the configuration is shared */ +#include + +#endif /* __CONFIGS_SC_SPS_1_H__ */ -- cgit v1.2.1 From 04c79cbd5f8f773aa7823feec6e77862e7e6426f Mon Sep 17 00:00:00 2001 From: Dirk Behme Date: Mon, 15 Jul 2013 15:58:27 +0200 Subject: mxc_gpio: Correct the GPIO handling in gpio_direction_output() Setting the direction and an output value should be done by First, set the desired output value. Then, switch to output. If this is done in the inverse order, like at the moment, there can be a glitch on the GPIO line while switching first the old output value and aftwards the new one. Fix this by inverting the order of the direction/set_value calls. Signed-off-by: Dirk Behme Acked-by: Stefano Babic --- drivers/gpio/mxc_gpio.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/gpio/mxc_gpio.c b/drivers/gpio/mxc_gpio.c index a3880641f0..1d820d4c3e 100644 --- a/drivers/gpio/mxc_gpio.c +++ b/drivers/gpio/mxc_gpio.c @@ -143,10 +143,10 @@ int gpio_direction_input(unsigned gpio) int gpio_direction_output(unsigned gpio, int value) { - int ret = mxc_gpio_direction(gpio, MXC_GPIO_DIRECTION_OUT); + int ret = gpio_set_value(gpio, value); if (ret < 0) return ret; - return gpio_set_value(gpio, value); + return mxc_gpio_direction(gpio, MXC_GPIO_DIRECTION_OUT); } -- cgit v1.2.1 From d727ab3c6ab6328e645c03e38199c256259a2dc3 Mon Sep 17 00:00:00 2001 From: Otavio Salvador Date: Sat, 20 Jul 2013 17:21:19 -0300 Subject: wandboard: Use splash image at screen center by default Signed-off-by: Otavio Salvador Acked-by: Fabio Estevam --- include/configs/wandboard.h | 1 + 1 file changed, 1 insertion(+) diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h index ee6bf216bd..dd06bd70fc 100644 --- a/include/configs/wandboard.h +++ b/include/configs/wandboard.h @@ -113,6 +113,7 @@ "script=boot.scr\0" \ "uimage=uImage\0" \ "console=ttymxc0\0" \ + "splashpos=m,m\0" \ "fdt_high=0xffffffff\0" \ "initrd_high=0xffffffff\0" \ "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ -- cgit v1.2.1 From f8b1e86d4707718e52cf6466845e463c358627ee Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Fri, 26 Jul 2013 11:37:17 -0300 Subject: mx6qsabrelite: Remove mx6qsabrelite code in favor of nitrogen6x mx6qsabrelite and nitrogen6q boards are hardware compatible, so let's avoid the code duplication and only use the nitrogen6x source code to make board code maintainance easier. Tested booting a mainline device tree kernel on a mx6qsabrelite board. Signed-off-by: Fabio Estevam --- MAINTAINERS | 2 +- board/boundary/nitrogen6x/README.mx6qsabrelite | 72 +++ board/freescale/mx6qsabrelite/Makefile | 41 -- board/freescale/mx6qsabrelite/README | 72 --- board/freescale/mx6qsabrelite/mx6qsabrelite.c | 848 ------------------------- boards.cfg | 2 +- include/configs/mx6qsabrelite.h | 297 --------- include/configs/nitrogen6x.h | 80 ++- 8 files changed, 153 insertions(+), 1261 deletions(-) create mode 100644 board/boundary/nitrogen6x/README.mx6qsabrelite delete mode 100644 board/freescale/mx6qsabrelite/Makefile delete mode 100644 board/freescale/mx6qsabrelite/README delete mode 100644 board/freescale/mx6qsabrelite/mx6qsabrelite.c delete mode 100644 include/configs/mx6qsabrelite.h diff --git a/MAINTAINERS b/MAINTAINERS index 081cf968e8..0a900dcdf2 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -601,7 +601,6 @@ Jason Liu mx53evk i.MX53 mx53loco i.MX53 mx6qarm2 i.MX6Q - mx6qsabrelite i.MX6Q Enric Balletbo i Serra @@ -1067,6 +1066,7 @@ Pali Rohár nokia_rx51 ARM ARMV7 (OMAP34xx SoC) Eric Nelson + mx6qsabrelite i.MX6Q 1GB nitrogen6dl i.MX6DL 1GB nitrogen6dl2g i.MX6DL 2GB nitrogen6q i.MX6Q/6D 1GB diff --git a/board/boundary/nitrogen6x/README.mx6qsabrelite b/board/boundary/nitrogen6x/README.mx6qsabrelite new file mode 100644 index 0000000000..12a9c856cf --- /dev/null +++ b/board/boundary/nitrogen6x/README.mx6qsabrelite @@ -0,0 +1,72 @@ +U-Boot for the Freescale i.MX6q SabreLite board + +This file contains information for the port of U-Boot to the Freescale +i.MX6q SabreLite board. + +1. Boot source, boot from SD card +--------------------------------- + +The recent mainline U-Boot for the Freescale i.MX6q SabreLite board supports +boot from SD card only. However, by default, the SabreLite +boards boot from the SPI NOR flash. These boards need to be reflashed with +a small SD card loader to support boot from SD card. This small SD card loader +will be flashed into the SPI NOR. The board will still boot from SPI NOR, but +the loader will in turn request the BootROM to load the U-Boot from SD card. + +The SD card loader is available from + +https://wiki.linaro.org/Boards/MX6QSabreLite + +under a open-source 3-clause BSD license. + +To update the SPI-NOR on the SabreLite board without the Freescale +manufacturing tool use the following procedure: + +1. Write this SD card loader onto a large SD card using: + + sudo dd if=iMX6DQ_SPI_to_uSDHC3.bin of=/dev/sXx + +Note: Replace sXx with the device representing the SD card in your system. + +Note: This writes SD card loader at address 0 + +2. Put this SD card into the slot for the large SD card (SD3 on the bottom of +the board). Make sure SW1 switch is at position "00", so that it can boot +from the fuses. + +3. Power-up the SabreLite, press 'space' to enter command mode in the U-Boot +(the default one the board is shipped with, starting from the SPI NOR) and +enter the following commands: + + MX6Q SABRELITE U-Boot > mmc dev 0 + MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200 + MX6Q SABRELITE U-Boot > sf probe + MX6Q SABRELITE U-Boot > sf erase 0 0x40000 + MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000 + +4. done. + +In case you somehow do not succeed with this procedure you will have to use +the Freescale manufacturing tool in order to reflash the SPI-NOR. + +Note: The board now boots from full size SD3 on the bottom of the board. NOT + the micro SD4/BOOT slot on the top of the board. I.e. you have to use + full size SD cards. + +This information is taken from + +https://wiki.linaro.org/Boards/MX6QSabreLite + +2. Build +-------- + +To build U-Boot for the SabreLite board: + + make mx6qsabrelite_config + make + +To copy the resulting u-boot.imx to the SD card: + + sudo dd if=u-boot.imx of=/dev/sXx bs=512 seek=2&&sudo sync + +Note: Replace sXx with the device representing the SD card in your system. diff --git a/board/freescale/mx6qsabrelite/Makefile b/board/freescale/mx6qsabrelite/Makefile deleted file mode 100644 index cf344e4323..0000000000 --- a/board/freescale/mx6qsabrelite/Makefile +++ /dev/null @@ -1,41 +0,0 @@ -# -# Copyright (C) 2007, Guennadi Liakhovetski -# -# (C) Copyright 2011 Freescale Semiconductor, Inc. -# -# This program is free software; you can redistribute it and/or -# modify it under the terms of the GNU General Public License as -# published by the Free Software Foundation; either version 2 of -# the License, or (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc., 59 Temple Place, Suite 330, Boston, -# MA 02111-1307 USA -# - -include $(TOPDIR)/config.mk - -LIB = $(obj)lib$(BOARD).o - -COBJS := mx6qsabrelite.o - -SRCS := $(COBJS:.o=.c) -OBJS := $(addprefix $(obj),$(COBJS)) - -$(LIB): $(obj).depend $(OBJS) - $(call cmd_link_o_target, $(OBJS)) - -######################################################################### - -# defines $(obj).depend target -include $(SRCTREE)/rules.mk - -sinclude $(obj).depend - -######################################################################### diff --git a/board/freescale/mx6qsabrelite/README b/board/freescale/mx6qsabrelite/README deleted file mode 100644 index 12a9c856cf..0000000000 --- a/board/freescale/mx6qsabrelite/README +++ /dev/null @@ -1,72 +0,0 @@ -U-Boot for the Freescale i.MX6q SabreLite board - -This file contains information for the port of U-Boot to the Freescale -i.MX6q SabreLite board. - -1. Boot source, boot from SD card ---------------------------------- - -The recent mainline U-Boot for the Freescale i.MX6q SabreLite board supports -boot from SD card only. However, by default, the SabreLite -boards boot from the SPI NOR flash. These boards need to be reflashed with -a small SD card loader to support boot from SD card. This small SD card loader -will be flashed into the SPI NOR. The board will still boot from SPI NOR, but -the loader will in turn request the BootROM to load the U-Boot from SD card. - -The SD card loader is available from - -https://wiki.linaro.org/Boards/MX6QSabreLite - -under a open-source 3-clause BSD license. - -To update the SPI-NOR on the SabreLite board without the Freescale -manufacturing tool use the following procedure: - -1. Write this SD card loader onto a large SD card using: - - sudo dd if=iMX6DQ_SPI_to_uSDHC3.bin of=/dev/sXx - -Note: Replace sXx with the device representing the SD card in your system. - -Note: This writes SD card loader at address 0 - -2. Put this SD card into the slot for the large SD card (SD3 on the bottom of -the board). Make sure SW1 switch is at position "00", so that it can boot -from the fuses. - -3. Power-up the SabreLite, press 'space' to enter command mode in the U-Boot -(the default one the board is shipped with, starting from the SPI NOR) and -enter the following commands: - - MX6Q SABRELITE U-Boot > mmc dev 0 - MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200 - MX6Q SABRELITE U-Boot > sf probe - MX6Q SABRELITE U-Boot > sf erase 0 0x40000 - MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000 - -4. done. - -In case you somehow do not succeed with this procedure you will have to use -the Freescale manufacturing tool in order to reflash the SPI-NOR. - -Note: The board now boots from full size SD3 on the bottom of the board. NOT - the micro SD4/BOOT slot on the top of the board. I.e. you have to use - full size SD cards. - -This information is taken from - -https://wiki.linaro.org/Boards/MX6QSabreLite - -2. Build --------- - -To build U-Boot for the SabreLite board: - - make mx6qsabrelite_config - make - -To copy the resulting u-boot.imx to the SD card: - - sudo dd if=u-boot.imx of=/dev/sXx bs=512 seek=2&&sudo sync - -Note: Replace sXx with the device representing the SD card in your system. diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c deleted file mode 100644 index 862bc3099d..0000000000 --- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c +++ /dev/null @@ -1,848 +0,0 @@ -/* - * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. - * - * See file CREDITS for list of people who contributed to this - * project. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \ - PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \ - PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \ - PAD_CTL_SRE_FAST | PAD_CTL_HYS) - -#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - -#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \ - PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST) - -#define BUTTON_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS) - -#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ - PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \ - PAD_CTL_ODE | PAD_CTL_SRE_FAST) - -int dram_init(void) -{ - gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); - - return 0; -} - -iomux_v3_cfg_t const uart1_pads[] = { - MX6_PAD_SD3_DAT6__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_SD3_DAT7__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - -iomux_v3_cfg_t const uart2_pads[] = { - MX6_PAD_EIM_D26__UART2_TXD | MUX_PAD_CTRL(UART_PAD_CTRL), - MX6_PAD_EIM_D27__UART2_RXD | MUX_PAD_CTRL(UART_PAD_CTRL), -}; - -#define PC MUX_PAD_CTRL(I2C_PAD_CTRL) - -/* I2C1, SGTL5000 */ -struct i2c_pads_info i2c_pad_info0 = { - .scl = { - .i2c_mode = MX6_PAD_EIM_D21__I2C1_SCL | PC, - .gpio_mode = MX6_PAD_EIM_D21__GPIO_3_21 | PC, - .gp = IMX_GPIO_NR(3, 21) - }, - .sda = { - .i2c_mode = MX6_PAD_EIM_D28__I2C1_SDA | PC, - .gpio_mode = MX6_PAD_EIM_D28__GPIO_3_28 | PC, - .gp = IMX_GPIO_NR(3, 28) - } -}; - -/* I2C2 Camera, MIPI */ -struct i2c_pads_info i2c_pad_info1 = { - .scl = { - .i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC, - .gpio_mode = MX6_PAD_KEY_COL3__GPIO_4_12 | PC, - .gp = IMX_GPIO_NR(4, 12) - }, - .sda = { - .i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC, - .gpio_mode = MX6_PAD_KEY_ROW3__GPIO_4_13 | PC, - .gp = IMX_GPIO_NR(4, 13) - } -}; - -/* I2C3, J15 - RGB connector */ -struct i2c_pads_info i2c_pad_info2 = { - .scl = { - .i2c_mode = MX6_PAD_GPIO_5__I2C3_SCL | PC, - .gpio_mode = MX6_PAD_GPIO_5__GPIO_1_5 | PC, - .gp = IMX_GPIO_NR(1, 5) - }, - .sda = { - .i2c_mode = MX6_PAD_GPIO_16__I2C3_SDA | PC, - .gpio_mode = MX6_PAD_GPIO_16__GPIO_7_11 | PC, - .gp = IMX_GPIO_NR(7, 11) - } -}; - -iomux_v3_cfg_t const usdhc3_pads[] = { - MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD3_DAT5__GPIO_7_0 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ -}; - -iomux_v3_cfg_t const usdhc4_pads[] = { - MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT0__USDHC4_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT1__USDHC4_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT2__USDHC4_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_SD4_DAT3__USDHC4_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), - MX6_PAD_NANDF_D6__GPIO_2_6 | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */ -}; - -iomux_v3_cfg_t const enet_pads1[] = { - MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), - /* pin 35 - 1 (PHY_AD2) on reset */ - MX6_PAD_RGMII_RXC__GPIO_6_30 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 32 - 1 - (MODE0) all */ - MX6_PAD_RGMII_RD0__GPIO_6_25 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 31 - 1 - (MODE1) all */ - MX6_PAD_RGMII_RD1__GPIO_6_27 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 28 - 1 - (MODE2) all */ - MX6_PAD_RGMII_RD2__GPIO_6_28 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 27 - 1 - (MODE3) all */ - MX6_PAD_RGMII_RD3__GPIO_6_29 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 33 - 1 - (CLK125_EN) 125Mhz clockout enabled */ - MX6_PAD_RGMII_RX_CTL__GPIO_6_24 | MUX_PAD_CTRL(NO_PAD_CTRL), - /* pin 42 PHY nRST */ - MX6_PAD_EIM_D23__GPIO_3_23 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -iomux_v3_cfg_t const enet_pads2[] = { - MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), - MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), -}; - -/* Button assignments for J14 */ -static iomux_v3_cfg_t const button_pads[] = { - /* Menu */ - MX6_PAD_NANDF_D1__GPIO_2_1 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), - /* Back */ - MX6_PAD_NANDF_D2__GPIO_2_2 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), - /* Labelled Search (mapped to Power under Android) */ - MX6_PAD_NANDF_D3__GPIO_2_3 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), - /* Home */ - MX6_PAD_NANDF_D4__GPIO_2_4 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), - /* Volume Down */ - MX6_PAD_GPIO_19__GPIO_4_5 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), - /* Volume Up */ - MX6_PAD_GPIO_18__GPIO_7_13 | MUX_PAD_CTRL(BUTTON_PAD_CTRL), -}; - -static void setup_iomux_enet(void) -{ - gpio_direction_output(IMX_GPIO_NR(3, 23), 0); - gpio_direction_output(IMX_GPIO_NR(6, 30), 1); - gpio_direction_output(IMX_GPIO_NR(6, 25), 1); - gpio_direction_output(IMX_GPIO_NR(6, 27), 1); - gpio_direction_output(IMX_GPIO_NR(6, 28), 1); - gpio_direction_output(IMX_GPIO_NR(6, 29), 1); - imx_iomux_v3_setup_multiple_pads(enet_pads1, ARRAY_SIZE(enet_pads1)); - gpio_direction_output(IMX_GPIO_NR(6, 24), 1); - - /* Need delay 10ms according to KSZ9021 spec */ - udelay(1000 * 10); - gpio_set_value(IMX_GPIO_NR(3, 23), 1); - - imx_iomux_v3_setup_multiple_pads(enet_pads2, ARRAY_SIZE(enet_pads2)); -} - -iomux_v3_cfg_t const usb_pads[] = { - MX6_PAD_GPIO_17__GPIO_7_12 | MUX_PAD_CTRL(NO_PAD_CTRL), -}; - -static void setup_iomux_uart(void) -{ - imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); - imx_iomux_v3_setup_multiple_pads(uart2_pads, ARRAY_SIZE(uart2_pads)); -} - -#ifdef CONFIG_USB_EHCI_MX6 -int board_ehci_hcd_init(int port) -{ - imx_iomux_v3_setup_multiple_pads(usb_pads, ARRAY_SIZE(usb_pads)); - - /* Reset USB hub */ - gpio_direction_output(IMX_GPIO_NR(7, 12), 0); - mdelay(2); - gpio_set_value(IMX_GPIO_NR(7, 12), 1); - - return 0; -} -#endif - -#ifdef CONFIG_FSL_ESDHC -struct fsl_esdhc_cfg usdhc_cfg[2] = { - {USDHC3_BASE_ADDR}, - {USDHC4_BASE_ADDR}, -}; - -int board_mmc_getcd(struct mmc *mmc) -{ - struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; - int ret; - - if (cfg->esdhc_base == USDHC3_BASE_ADDR) { - gpio_direction_input(IMX_GPIO_NR(7, 0)); - ret = !gpio_get_value(IMX_GPIO_NR(7, 0)); - } else { - gpio_direction_input(IMX_GPIO_NR(2, 6)); - ret = !gpio_get_value(IMX_GPIO_NR(2, 6)); - } - - return ret; -} - -int board_mmc_init(bd_t *bis) -{ - s32 status = 0; - u32 index = 0; - - usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); - usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); - - usdhc_cfg[0].max_bus_width = 4; - usdhc_cfg[1].max_bus_width = 4; - - for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { - switch (index) { - case 0: - imx_iomux_v3_setup_multiple_pads( - usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); - break; - case 1: - imx_iomux_v3_setup_multiple_pads( - usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); - break; - default: - printf("Warning: you configured more USDHC controllers" - "(%d) then supported by the board (%d)\n", - index + 1, CONFIG_SYS_FSL_USDHC_NUM); - return status; - } - - status |= fsl_esdhc_initialize(bis, &usdhc_cfg[index]); - } - - return status; -} -#endif - -#ifdef CONFIG_MXC_SPI -iomux_v3_cfg_t const ecspi1_pads[] = { - /* SS1 */ - MX6_PAD_EIM_D19__GPIO_3_19 | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL), - MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL), -}; - -void setup_spi(void) -{ - imx_iomux_v3_setup_multiple_pads(ecspi1_pads, - ARRAY_SIZE(ecspi1_pads)); -} -#endif - -int board_phy_config(struct phy_device *phydev) -{ - /* min rx data delay */ - ksz9021_phy_extended_write(phydev, - MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW, 0x0); - /* min tx data delay */ - ksz9021_phy_extended_write(phydev, - MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW, 0x0); - /* max rx/tx clock delay, min rx/tx control */ - ksz9021_phy_extended_write(phydev, - MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, 0xf0f0); - if (phydev->drv->config) - phydev->drv->config(phydev); - - return 0; -} - -int board_eth_init(bd_t *bis) -{ - uint32_t base = IMX_FEC_BASE; - struct mii_dev *bus = NULL; - struct phy_device *phydev = NULL; - int ret; - - setup_iomux_enet(); - -#ifdef CONFIG_FEC_MXC - bus = fec_get_miibus(base, -1); - if (!bus) - return 0; - /* scan phy 4,5,6,7 */ - phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII); - if (!phydev) { - free(bus); - return 0; - } - printf("using phy at %d\n", phydev->addr); - ret = fec_probe(bis, -1, base, bus, phydev); - if (ret) { - printf("FEC MXC: %s:failed\n", __func__); - free(phydev); - free(bus); - } -#endif - return 0; -} - -static void setup_buttons(void) -{ - imx_iomux_v3_setup_multiple_pads(button_pads, - ARRAY_SIZE(button_pads)); -} - -#ifdef CONFIG_CMD_SATA - -int setup_sata(void) -{ - struct iomuxc_base_regs *const iomuxc_regs - = (struct iomuxc_base_regs *) IOMUXC_BASE_ADDR; - int ret = enable_sata_clock(); - if (ret) - return ret; - - clrsetbits_le32(&iomuxc_regs->gpr[13], - IOMUXC_GPR13_SATA_MASK, - IOMUXC_GPR13_SATA_PHY_8_RXEQ_3P0DB - |IOMUXC_GPR13_SATA_PHY_7_SATA2M - |IOMUXC_GPR13_SATA_SPEED_3G - |(3<phy_stat0) & HDMI_PHY_HPD; -} - -static void enable_hdmi(struct display_info_t const *dev) -{ - struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - u8 reg; - printf("%s: setup HDMI monitor\n", __func__); - reg = readb(&hdmi->phy_conf0); - reg |= HDMI_PHY_CONF0_PDZ_MASK; - writeb(reg, &hdmi->phy_conf0); - - udelay(3000); - reg |= HDMI_PHY_CONF0_ENTMDS_MASK; - writeb(reg, &hdmi->phy_conf0); - udelay(3000); - reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK; - writeb(reg, &hdmi->phy_conf0); - writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz); -} - -static int detect_i2c(struct display_info_t const *dev) -{ - return ((0 == i2c_set_bus_num(dev->bus)) - && - (0 == i2c_probe(dev->addr))); -} - -static void enable_lvds(struct display_info_t const *dev) -{ - struct iomuxc *iomux = (struct iomuxc *) - IOMUXC_BASE_ADDR; - u32 reg = readl(&iomux->gpr[2]); - reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT; - writel(reg, &iomux->gpr[2]); - gpio_direction_output(LVDS_BACKLIGHT_GP, 1); -} - -static void enable_rgb(struct display_info_t const *dev) -{ - imx_iomux_v3_setup_multiple_pads( - rgb_pads, - ARRAY_SIZE(rgb_pads)); - gpio_direction_output(RGB_BACKLIGHT_GP, 1); -} - -static struct display_info_t const displays[] = {{ - .bus = -1, - .addr = 0, - .pixfmt = IPU_PIX_FMT_RGB24, - .detect = detect_hdmi, - .enable = enable_hdmi, - .mode = { - .name = "HDMI", - .refresh = 60, - .xres = 1024, - .yres = 768, - .pixclock = 15385, - .left_margin = 220, - .right_margin = 40, - .upper_margin = 21, - .lower_margin = 7, - .hsync_len = 60, - .vsync_len = 10, - .sync = FB_SYNC_EXT, - .vmode = FB_VMODE_NONINTERLACED -} }, { - .bus = 2, - .addr = 0x4, - .pixfmt = IPU_PIX_FMT_LVDS666, - .detect = detect_i2c, - .enable = enable_lvds, - .mode = { - .name = "Hannstar-XGA", - .refresh = 60, - .xres = 1024, - .yres = 768, - .pixclock = 15385, - .left_margin = 220, - .right_margin = 40, - .upper_margin = 21, - .lower_margin = 7, - .hsync_len = 60, - .vsync_len = 10, - .sync = FB_SYNC_EXT, - .vmode = FB_VMODE_NONINTERLACED -} }, { - .bus = 2, - .addr = 0x38, - .pixfmt = IPU_PIX_FMT_LVDS666, - .detect = detect_i2c, - .enable = enable_lvds, - .mode = { - .name = "wsvga-lvds", - .refresh = 60, - .xres = 1024, - .yres = 600, - .pixclock = 15385, - .left_margin = 220, - .right_margin = 40, - .upper_margin = 21, - .lower_margin = 7, - .hsync_len = 60, - .vsync_len = 10, - .sync = FB_SYNC_EXT, - .vmode = FB_VMODE_NONINTERLACED -} }, { - .bus = 2, - .addr = 0x48, - .pixfmt = IPU_PIX_FMT_RGB666, - .detect = detect_i2c, - .enable = enable_rgb, - .mode = { - .name = "wvga-rgb", - .refresh = 57, - .xres = 800, - .yres = 480, - .pixclock = 37037, - .left_margin = 40, - .right_margin = 60, - .upper_margin = 10, - .lower_margin = 10, - .hsync_len = 20, - .vsync_len = 10, - .sync = 0, - .vmode = FB_VMODE_NONINTERLACED -} } }; - -int board_video_skip(void) -{ - int i; - int ret; - char const *panel = getenv("panel"); - if (!panel) { - for (i = 0; i < ARRAY_SIZE(displays); i++) { - struct display_info_t const *dev = displays+i; - if (dev->detect(dev)) { - panel = dev->mode.name; - printf("auto-detected panel %s\n", panel); - break; - } - } - if (!panel) { - panel = displays[0].mode.name; - printf("No panel detected: default to %s\n", panel); - } - } else { - for (i = 0; i < ARRAY_SIZE(displays); i++) { - if (!strcmp(panel, displays[i].mode.name)) - break; - } - } - if (i < ARRAY_SIZE(displays)) { - ret = ipuv3_fb_init(&displays[i].mode, 0, - displays[i].pixfmt); - if (!ret) { - displays[i].enable(displays+i); - printf("Display: %s (%ux%u)\n", - displays[i].mode.name, - displays[i].mode.xres, - displays[i].mode.yres); - } else - printf("LCD %s cannot be configured: %d\n", - displays[i].mode.name, ret); - } else { - printf("unsupported panel %s\n", panel); - ret = -EINVAL; - } - return (0 != ret); -} - -static void setup_display(void) -{ - struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; - struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; - struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; - struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - - int reg; - - /* Turn on LDB0,IPU,IPU DI0 clocks */ - reg = __raw_readl(&mxc_ccm->CCGR3); - reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET - |MXC_CCM_CCGR3_LDB_DI0_MASK; - writel(reg, &mxc_ccm->CCGR3); - - /* Turn on HDMI PHY clock */ - reg = __raw_readl(&mxc_ccm->CCGR2); - reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK - |MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK; - writel(reg, &mxc_ccm->CCGR2); - - /* clear HDMI PHY reset */ - writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz); - - /* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */ - writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr); - writel(0x13<pfd_480_set); - - /* set LDB0, LDB1 clk select to 011/011 */ - reg = readl(&mxc_ccm->cs2cdr); - reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK - |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK); - reg |= (3<cs2cdr); - - reg = readl(&mxc_ccm->cscmr2); - reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV; - writel(reg, &mxc_ccm->cscmr2); - - reg = readl(&mxc_ccm->chsccdr); - reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK - |MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK - |MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK); - reg |= (CHSCCDR_CLK_SEL_LDB_DI0 - <chsccdr); - - reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES - |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH - |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW - |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG - |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT - |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG - |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT - |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED - |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0; - writel(reg, &iomux->gpr[2]); - - reg = readl(&iomux->gpr[3]); - reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK) - | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 - <gpr[3]); - - /* backlights off until needed */ - imx_iomux_v3_setup_multiple_pads(backlight_pads, - ARRAY_SIZE(backlight_pads)); - gpio_direction_input(LVDS_BACKLIGHT_GP); - gpio_direction_input(RGB_BACKLIGHT_GP); -} -#endif - -int board_early_init_f(void) -{ - setup_iomux_uart(); - setup_buttons(); - -#if defined(CONFIG_VIDEO_IPUV3) - setup_display(); -#endif - return 0; -} - -/* - * Do not overwrite the console - * Use always serial for U-Boot console - */ -int overwrite_console(void) -{ - return 1; -} - -int board_init(void) -{ - /* address of boot parameters */ - gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; - -#ifdef CONFIG_MXC_SPI - setup_spi(); -#endif - setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info0); - setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); - setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); - -#ifdef CONFIG_CMD_SATA - setup_sata(); -#endif - - return 0; -} - -int checkboard(void) -{ - puts("Board: MX6Q-Sabre Lite\n"); - - return 0; -} - -struct button_key { - char const *name; - unsigned gpnum; - char ident; -}; - -static struct button_key const buttons[] = { - {"back", IMX_GPIO_NR(2, 2), 'B'}, - {"home", IMX_GPIO_NR(2, 4), 'H'}, - {"menu", IMX_GPIO_NR(2, 1), 'M'}, - {"search", IMX_GPIO_NR(2, 3), 'S'}, - {"volup", IMX_GPIO_NR(7, 13), 'V'}, - {"voldown", IMX_GPIO_NR(4, 5), 'v'}, -}; - -/* - * generate a null-terminated string containing the buttons pressed - * returns number of keys pressed - */ -static int read_keys(char *buf) -{ - int i, numpressed = 0; - for (i = 0; i < ARRAY_SIZE(buttons); i++) { - if (!gpio_get_value(buttons[i].gpnum)) - buf[numpressed++] = buttons[i].ident; - } - buf[numpressed] = '\0'; - return numpressed; -} - -static int do_kbd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - char envvalue[ARRAY_SIZE(buttons)+1]; - int numpressed = read_keys(envvalue); - setenv("keybd", envvalue); - return numpressed == 0; -} - -U_BOOT_CMD( - kbd, 1, 1, do_kbd, - "Tests for keypresses, sets 'keybd' environment variable", - "Returns 0 (true) to shell if key is pressed." -); - -#ifdef CONFIG_PREBOOT -static char const kbd_magic_prefix[] = "key_magic"; -static char const kbd_command_prefix[] = "key_cmd"; - -static void preboot_keys(void) -{ - int numpressed; - char keypress[ARRAY_SIZE(buttons)+1]; - numpressed = read_keys(keypress); - if (numpressed) { - char *kbd_magic_keys = getenv("magic_keys"); - char *suffix; - /* - * loop over all magic keys - */ - for (suffix = kbd_magic_keys; *suffix; ++suffix) { - char *keys; - char magic[sizeof(kbd_magic_prefix) + 1]; - sprintf(magic, "%s%c", kbd_magic_prefix, *suffix); - keys = getenv(magic); - if (keys) { - if (!strcmp(keys, keypress)) - break; - } - } - if (*suffix) { - char cmd_name[sizeof(kbd_command_prefix) + 1]; - char *cmd; - sprintf(cmd_name, "%s%c", kbd_command_prefix, *suffix); - cmd = getenv(cmd_name); - if (cmd) { - setenv("preboot", cmd); - return; - } - } - } -} -#endif - -#ifdef CONFIG_CMD_BMODE -static const struct boot_mode board_boot_modes[] = { - /* 4 bit bus width */ - {"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, - {"mmc1", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, - {NULL, 0}, -}; -#endif - -int misc_init_r(void) -{ -#ifdef CONFIG_PREBOOT - preboot_keys(); -#endif - -#ifdef CONFIG_CMD_BMODE - add_board_boot_modes(board_boot_modes); -#endif - return 0; -} diff --git a/boards.cfg b/boards.cfg index 6a368de800..f919c53f9e 100644 --- a/boards.cfg +++ b/boards.cfg @@ -268,7 +268,7 @@ vision2 arm armv7 vision2 ttcontr cgtqmx6qeval arm armv7 cgtqmx6eval congatec mx6 cgtqmx6eval:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q mx6qarm2 arm armv7 mx6qarm2 freescale mx6 mx6qarm2:IMX_CONFIG=board/freescale/mx6qarm2/imximage.cfg mx6qsabreauto arm armv7 mx6qsabreauto freescale mx6 mx6qsabreauto:IMX_CONFIG=board/freescale/mx6qsabreauto/imximage.cfg,MX6Q -mx6qsabrelite arm armv7 mx6qsabrelite freescale mx6 mx6qsabrelite:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg +mx6qsabrelite arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q.cfg,MX6Q,DDR_MB=1024,SABRELITE mx6dlsabresd arm armv7 mx6sabresd freescale mx6 mx6sabresd:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL mx6qsabresd arm armv7 mx6sabresd freescale mx6 mx6sabresd:IMX_CONFIG=board/freescale/imx/ddr/mx6q_4x_mt41j128.cfg,MX6Q mx6slevk arm armv7 mx6slevk freescale mx6 mx6slevk:IMX_CONFIG=board/freescale/mx6slevk/imximage.cfg,MX6SL diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h deleted file mode 100644 index c7db81d0d8..0000000000 --- a/include/configs/mx6qsabrelite.h +++ /dev/null @@ -1,297 +0,0 @@ -/* - * Copyright (C) 2010-2011 Freescale Semiconductor, Inc. - * - * Configuration settings for the Freescale i.MX6Q Sabre Lite board. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of - * the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, - * MA 02111-1307 USA - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_MX6 -#define CONFIG_MX6Q - -#include "mx6_common.h" - -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DISPLAY_BOARDINFO - -#define CONFIG_MACH_TYPE 3769 - -#include -#include - -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_INITRD_TAG -#define CONFIG_REVISION_TAG - -/* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) - -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_MISC_INIT_R -#define CONFIG_MXC_GPIO - -#define CONFIG_CMD_FUSE -#ifdef CONFIG_CMD_FUSE -#define CONFIG_MXC_OCOTP -#endif - -#define CONFIG_MXC_UART -#define CONFIG_MXC_UART_BASE UART2_BASE - -#define CONFIG_CMD_SF -#ifdef CONFIG_CMD_SF -#define CONFIG_SPI_FLASH -#define CONFIG_SPI_FLASH_SST -#define CONFIG_MXC_SPI -#define CONFIG_SF_DEFAULT_BUS 0 -#define CONFIG_SF_DEFAULT_CS (0|(IMX_GPIO_NR(3, 19)<<8)) -#define CONFIG_SF_DEFAULT_SPEED 25000000 -#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0) -#endif - -/* I2C Configs */ -#define CONFIG_CMD_I2C -#define CONFIG_I2C_MULTI_BUS -#define CONFIG_I2C_MXC -#define CONFIG_SYS_I2C_SPEED 100000 - -/* MMC Configs */ -#define CONFIG_FSL_ESDHC -#define CONFIG_FSL_USDHC -#define CONFIG_SYS_FSL_ESDHC_ADDR 0 -#define CONFIG_SYS_FSL_USDHC_NUM 2 - -#define CONFIG_MMC -#define CONFIG_CMD_MMC -#define CONFIG_GENERIC_MMC -#define CONFIG_BOUNCE_BUFFER -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_DOS_PARTITION - -#define CONFIG_CMD_SATA -/* - * SATA Configs - */ -#ifdef CONFIG_CMD_SATA -#define CONFIG_DWC_AHSATA -#define CONFIG_SYS_SATA_MAX_DEVICE 1 -#define CONFIG_DWC_AHSATA_PORT_ID 0 -#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR -#define CONFIG_LBA48 -#define CONFIG_LIBATA -#endif - -#define CONFIG_CMD_PING -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_FEC_MXC -#define CONFIG_MII -#define IMX_FEC_BASE ENET_BASE_ADDR -#define CONFIG_FEC_XCV_TYPE RGMII -#define CONFIG_ETHPRIME "FEC" -#define CONFIG_FEC_MXC_PHYADDR 6 -#define CONFIG_PHYLIB -#define CONFIG_PHY_MICREL -#define CONFIG_PHY_MICREL_KSZ9021 - -/* USB Configs */ -#define CONFIG_CMD_USB -#define CONFIG_CMD_FAT -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MX6 -#define CONFIG_USB_STORAGE -#define CONFIG_USB_HOST_ETHER -#define CONFIG_USB_ETHER_ASIX -#define CONFIG_USB_ETHER_SMSC95XX -#define CONFIG_MXC_USB_PORT 1 -#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW) -#define CONFIG_MXC_USB_FLAGS 0 - -/* Miscellaneous commands */ -#define CONFIG_CMD_BMODE - -/* Framebuffer and LCD */ -#define CONFIG_VIDEO -#define CONFIG_VIDEO_IPUV3 -#define CONFIG_CFB_CONSOLE -#define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE -#define CONFIG_VIDEO_BMP_RLE8 -#define CONFIG_SPLASH_SCREEN -#define CONFIG_BMP_16BPP -#define CONFIG_VIDEO_LOGO -#define CONFIG_IPUV3_CLK 260000000 - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* Command definition */ -#include - -#undef CONFIG_CMD_IMLS - -#define CONFIG_BOOTDELAY 1 - -#define CONFIG_PREBOOT "" - -#define CONFIG_LOADADDR 0x12000000 -#define CONFIG_SYS_TEXT_BASE 0x17800000 - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "script=boot.scr\0" \ - "uimage=uImage\0" \ - "console=ttymxc1\0" \ - "fdt_high=0xffffffff\0" \ - "initrd_high=0xffffffff\0" \ - "fdt_file=imx6q-sabrelite.dtb\0" \ - "fdt_addr=0x11000000\0" \ - "boot_fdt=try\0" \ - "ip_dyn=yes\0" \ - "mmcdev=0\0" \ - "mmcpart=1\0" \ - "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ - "mmcargs=setenv bootargs console=${console},${baudrate} " \ - "root=${mmcroot}\0" \ - "loadbootscript=" \ - "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ - "bootscript=echo Running bootscript from mmc ...; " \ - "source\0" \ - "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ - "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ - "mmcboot=echo Booting from mmc ...; " \ - "run mmcargs; " \ - "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ - "if run loadfdt; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "if test ${boot_fdt} = try; then " \ - "bootm; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi; " \ - "else " \ - "bootm; " \ - "fi;\0" \ - "netargs=setenv bootargs console=${console},${baudrate} " \ - "root=/dev/nfs " \ - "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ - "netboot=echo Booting from net ...; " \ - "run netargs; " \ - "if test ${ip_dyn} = yes; then " \ - "setenv get_cmd dhcp; " \ - "else " \ - "setenv get_cmd tftp; " \ - "fi; " \ - "${get_cmd} ${uimage}; " \ - "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ - "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ - "bootm ${loadaddr} - ${fdt_addr}; " \ - "else " \ - "if test ${boot_fdt} = try; then " \ - "bootm; " \ - "else " \ - "echo WARN: Cannot load the DT; " \ - "fi; " \ - "fi; " \ - "else " \ - "bootm; " \ - "fi;\0" - -#define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev}; if mmc rescan; then " \ - "if run loadbootscript; then " \ - "run bootscript; " \ - "else " \ - "if run loaduimage; then " \ - "run mmcboot; " \ - "else run netboot; " \ - "fi; " \ - "fi; " \ - "else run netboot; fi" - -/* Miscellaneous configurable options */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_HUSH_PARSER -#define CONFIG_SYS_PROMPT "MX6QSABRELITE U-Boot > " -#define CONFIG_AUTO_COMPLETE -#define CONFIG_SYS_CBSIZE 256 - -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) -#define CONFIG_SYS_MAXARGS 16 -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE - -#define CONFIG_SYS_MEMTEST_START 0x10000000 -#define CONFIG_SYS_MEMTEST_END 0x10010000 -#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 - -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_SYS_HZ 1000 - -#define CONFIG_CMDLINE_EDITING - -/* Physical Memory Map */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR -#define PHYS_SDRAM_SIZE (1u * 1024 * 1024 * 1024) - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM -#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR -#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE - -#define CONFIG_SYS_INIT_SP_OFFSET \ - (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR \ - (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) - -/* FLASH and environment organization */ -#define CONFIG_SYS_NO_FLASH - -#define CONFIG_ENV_SIZE (8 * 1024) - -#define CONFIG_ENV_IS_IN_MMC -/* #define CONFIG_ENV_IS_IN_SPI_FLASH */ - -#if defined(CONFIG_ENV_IS_IN_MMC) -#define CONFIG_ENV_OFFSET (6 * 64 * 1024) -#define CONFIG_SYS_MMC_ENV_DEV 0 -#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH) -#define CONFIG_ENV_OFFSET (768 * 1024) -#define CONFIG_ENV_SECT_SIZE (8 * 1024) -#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS -#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS -#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE -#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED -#endif - -#define CONFIG_OF_LIBFDT -#define CONFIG_CMD_BOOTZ - -#ifndef CONFIG_SYS_DCACHE_OFF -#define CONFIG_CMD_CACHE -#endif - -#endif /* __CONFIG_H */ diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h index 74df66c22f..85eecfc6a4 100644 --- a/include/configs/nitrogen6x.h +++ b/include/configs/nitrogen6x.h @@ -186,6 +186,80 @@ #define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC +#if defined(CONFIG_SABRELITE) +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "console=ttymxc1\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=imx6q-sabrelite.dtb\0" \ + "fdt_addr=0x11000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev=0\0" \ + "mmcpart=1\0" \ + "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${uimage}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" +#else #define CONFIG_EXTRA_ENV_SETTINGS \ "console=ttymxc1\0" \ "clearenv=if sf probe || sf probe || sf probe 1 ; then " \ @@ -219,6 +293,7 @@ "done ; " \ "done\0" \ +#endif /* Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP #define CONFIG_SYS_HUSH_PARSER @@ -258,8 +333,11 @@ #define CONFIG_ENV_SIZE (8 * 1024) -/* #define CONFIG_ENV_IS_IN_MMC */ +#if defined(CONFIG_SABRELITE) +#define CONFIG_ENV_IS_IN_MMC +#else #define CONFIG_ENV_IS_IN_SPI_FLASH +#endif #if defined(CONFIG_ENV_IS_IN_MMC) #define CONFIG_ENV_OFFSET (6 * 64 * 1024) -- cgit v1.2.1 From 5ea7f0e328c19542ce96d8242125b51b3dbca86b Mon Sep 17 00:00:00 2001 From: Pardeep Kumar Singla Date: Thu, 25 Jul 2013 12:12:13 -0500 Subject: mx6: Factor out common HDMI setup code Instead of duplicating HDMI setup code for every mx6 board, factor out the common code Signed-off-by: Pardeep Kumar Singla Acked-By: Eric Nelson --- arch/arm/cpu/armv7/mx6/clock.c | 8 ++++++ arch/arm/cpu/armv7/mx6/soc.c | 43 +++++++++++++++++++++++++++++++ arch/arm/include/asm/arch-mx6/clock.h | 2 +- arch/arm/include/asm/arch-mx6/mxc_hdmi.h | 5 ++++ board/boundary/nitrogen6x/nitrogen6x.c | 44 +++++--------------------------- board/wandboard/wandboard.c | 44 +++----------------------------- include/configs/nitrogen6x.h | 1 + include/configs/wandboard.h | 1 + 8 files changed, 70 insertions(+), 78 deletions(-) diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c index 3c0d908d17..ce063ae9fe 100644 --- a/arch/arm/cpu/armv7/mx6/clock.c +++ b/arch/arm/cpu/armv7/mx6/clock.c @@ -468,6 +468,14 @@ int do_mx6_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) return 0; } +void enable_ipu_clock(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + int reg; + reg = readl(&mxc_ccm->CCGR3); + reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET; + writel(reg, &mxc_ccm->CCGR3); +} /***************************************************/ U_BOOT_CMD( diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c index fc436fbee7..a79369f32c 100644 --- a/arch/arm/cpu/armv7/mx6/soc.c +++ b/arch/arm/cpu/armv7/mx6/soc.c @@ -32,6 +32,8 @@ #include #include #include +#include +#include struct scu_regs { u32 ctrl; @@ -228,3 +230,44 @@ const struct boot_mode soc_boot_modes[] = { void s_init(void) { } + +#ifdef CONFIG_IMX_HDMI +void imx_enable_hdmi_phy(void) +{ + struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; + u8 reg; + reg = readb(&hdmi->phy_conf0); + reg |= HDMI_PHY_CONF0_PDZ_MASK; + writeb(reg, &hdmi->phy_conf0); + udelay(3000); + reg |= HDMI_PHY_CONF0_ENTMDS_MASK; + writeb(reg, &hdmi->phy_conf0); + udelay(3000); + reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK; + writeb(reg, &hdmi->phy_conf0); + writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz); +} + +void imx_setup_hdmi(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; + int reg; + + /* Turn on HDMI PHY clock */ + reg = readl(&mxc_ccm->CCGR2); + reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK| + MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK; + writel(reg, &mxc_ccm->CCGR2); + writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz); + reg = readl(&mxc_ccm->chsccdr); + reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK| + MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK| + MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK); + reg |= (CHSCCDR_PODF_DIVIDE_BY_3 + << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) + |(CHSCCDR_IPU_PRE_CLK_540M_PFD + << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET); + writel(reg, &mxc_ccm->chsccdr); +} +#endif diff --git a/arch/arm/include/asm/arch-mx6/clock.h b/arch/arm/include/asm/arch-mx6/clock.h index cfd4edcb5e..d03d24a796 100644 --- a/arch/arm/include/asm/arch-mx6/clock.h +++ b/arch/arm/include/asm/arch-mx6/clock.h @@ -65,5 +65,5 @@ void enable_ocotp_clk(unsigned char enable); void enable_usboh3_clk(unsigned char enable); int enable_sata_clock(void); int enable_i2c_clk(unsigned char enable, unsigned i2c_num); - +void enable_ipu_clock(void); #endif /* __ASM_ARCH_CLOCK_H */ diff --git a/arch/arm/include/asm/arch-mx6/mxc_hdmi.h b/arch/arm/include/asm/arch-mx6/mxc_hdmi.h index 9dccb3fef5..5cd6aa6359 100644 --- a/arch/arm/include/asm/arch-mx6/mxc_hdmi.h +++ b/arch/arm/include/asm/arch-mx6/mxc_hdmi.h @@ -21,6 +21,11 @@ #ifndef __MXC_HDMI_H__ #define __MXC_HDMI_H__ +#ifdef CONFIG_IMX_HDMI +void imx_enable_hdmi_phy(void); +void imx_setup_hdmi(void); +#endif + /* * Hdmi controller registers */ diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c index 8f0f9b8de2..1b82633944 100644 --- a/board/boundary/nitrogen6x/nitrogen6x.c +++ b/board/boundary/nitrogen6x/nitrogen6x.c @@ -480,22 +480,9 @@ static int detect_hdmi(struct display_info_t const *dev) return readb(&hdmi->phy_stat0) & HDMI_PHY_HPD; } -static void enable_hdmi(struct display_info_t const *dev) +static void do_enable_hdmi(struct display_info_t const *dev) { - struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - u8 reg; - printf("%s: setup HDMI monitor\n", __func__); - reg = readb(&hdmi->phy_conf0); - reg |= HDMI_PHY_CONF0_PDZ_MASK; - writeb(reg, &hdmi->phy_conf0); - - udelay(3000); - reg |= HDMI_PHY_CONF0_ENTMDS_MASK; - writeb(reg, &hdmi->phy_conf0); - udelay(3000); - reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK; - writeb(reg, &hdmi->phy_conf0); - writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz); + imx_enable_hdmi_phy(); } static int detect_i2c(struct display_info_t const *dev) @@ -528,7 +515,7 @@ static struct display_info_t const displays[] = {{ .addr = 0, .pixfmt = IPU_PIX_FMT_RGB24, .detect = detect_hdmi, - .enable = enable_hdmi, + .enable = do_enable_hdmi, .mode = { .name = "HDMI", .refresh = 60, @@ -653,25 +640,15 @@ static void setup_display(void) struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR; struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR; - struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - int reg; + enable_ipu_clock(); + imx_setup_hdmi(); /* Turn on LDB0,IPU,IPU DI0 clocks */ reg = __raw_readl(&mxc_ccm->CCGR3); - reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET - |MXC_CCM_CCGR3_LDB_DI0_MASK; + reg |= MXC_CCM_CCGR3_LDB_DI0_MASK; writel(reg, &mxc_ccm->CCGR3); - /* Turn on HDMI PHY clock */ - reg = __raw_readl(&mxc_ccm->CCGR2); - reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK - |MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK; - writel(reg, &mxc_ccm->CCGR2); - - /* clear HDMI PHY reset */ - writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz); - /* set PFD1_FRAC to 0x13 == 455 MHz (480*18)/0x13 */ writel(ANATOP_PFD_480_PFD1_FRAC_MASK, &anatop->pfd_480_clr); writel(0x13<pfd_480_set); @@ -689,15 +666,8 @@ static void setup_display(void) writel(reg, &mxc_ccm->cscmr2); reg = readl(&mxc_ccm->chsccdr); - reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK - |MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK - |MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK); reg |= (CHSCCDR_CLK_SEL_LDB_DI0 - <chsccdr); reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c index 43c02acfd1..6cd28eda87 100644 --- a/board/wandboard/wandboard.c +++ b/board/wandboard/wandboard.c @@ -211,23 +211,6 @@ int board_phy_config(struct phy_device *phydev) } #if defined(CONFIG_VIDEO_IPUV3) -static void enable_hdmi(void) -{ - struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - u8 reg; - reg = readb(&hdmi->phy_conf0); - reg |= HDMI_PHY_CONF0_PDZ_MASK; - writeb(reg, &hdmi->phy_conf0); - - udelay(3000); - reg |= HDMI_PHY_CONF0_ENTMDS_MASK; - writeb(reg, &hdmi->phy_conf0); - udelay(3000); - reg |= HDMI_PHY_CONF0_GEN2_TXPWRON_MASK; - writeb(reg, &hdmi->phy_conf0); - writeb(HDMI_MC_PHYRSTZ_ASSERT, &hdmi->mc_phyrstz); -} - static struct fb_videomode const hdmi = { .name = "HDMI", .refresh = 60, @@ -253,7 +236,7 @@ int board_video_skip(void) if (ret) printf("HDMI cannot be configured: %d\n", ret); - enable_hdmi(); + imx_enable_hdmi_phy(); return ret; } @@ -261,33 +244,14 @@ int board_video_skip(void) static void setup_display(void) { struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; - struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; int reg; - /* Turn on IPU clock */ - reg = readl(&mxc_ccm->CCGR3); - reg |= MXC_CCM_CCGR3_IPU1_IPU_DI0_OFFSET; - writel(reg, &mxc_ccm->CCGR3); - - /* Turn on HDMI PHY clock */ - reg = readl(&mxc_ccm->CCGR2); - reg |= MXC_CCM_CCGR2_HDMI_TX_IAHBCLK_MASK - | MXC_CCM_CCGR2_HDMI_TX_ISFRCLK_MASK; - writel(reg, &mxc_ccm->CCGR2); - - /* clear HDMI PHY reset */ - writeb(HDMI_MC_PHYRSTZ_DEASSERT, &hdmi->mc_phyrstz); + enable_ipu_clock(); + imx_setup_hdmi(); reg = readl(&mxc_ccm->chsccdr); - reg &= ~(MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_MASK - | MXC_CCM_CHSCCDR_IPU1_DI0_PODF_MASK - | MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_MASK); reg |= (CHSCCDR_CLK_SEL_LDB_DI0 - << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET) - | (CHSCCDR_PODF_DIVIDE_BY_3 - << MXC_CCM_CHSCCDR_IPU1_DI0_PODF_OFFSET) - | (CHSCCDR_IPU_PRE_CLK_540M_PFD - << MXC_CCM_CHSCCDR_IPU1_DI0_PRE_CLK_SEL_OFFSET); + << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); writel(reg, &mxc_ccm->chsccdr); } #endif /* CONFIG_VIDEO_IPUV3 */ diff --git a/include/configs/nitrogen6x.h b/include/configs/nitrogen6x.h index 85eecfc6a4..b057039170 100644 --- a/include/configs/nitrogen6x.h +++ b/include/configs/nitrogen6x.h @@ -154,6 +154,7 @@ #define CONFIG_IPUV3_CLK 260000000 #define CONFIG_CMD_HDMIDETECT #define CONFIG_CONSOLE_MUX +#define CONFIG_IMX_HDMI /* allow to overwrite serial and ethaddr */ #define CONFIG_ENV_OVERWRITE diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h index dd06bd70fc..1f83e89fa5 100644 --- a/include/configs/wandboard.h +++ b/include/configs/wandboard.h @@ -100,6 +100,7 @@ #define CONFIG_VIDEO_LOGO #define CONFIG_VIDEO_BMP_LOGO #define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_IMX_HDMI #if defined(CONFIG_MX6DL) #define CONFIG_DEFAULT_FDT_FILE "imx6dl-wandboard.dtb" -- cgit v1.2.1 From 58cc97877713f46d2e7dfd515844c29c70c56d82 Mon Sep 17 00:00:00 2001 From: Pardeep Kumar Singla Date: Thu, 25 Jul 2013 12:12:14 -0500 Subject: mx6qsabresd: Add splash screen support via HDMI Signed-off-by: Pardeep Kumar Singla --- board/freescale/mx6sabresd/mx6sabresd.c | 64 ++++++++++++++++++++++++++++++++- include/configs/mx6sabre_common.h | 3 +- include/configs/mx6sabresd.h | 19 ++++++++++ 3 files changed, 84 insertions(+), 2 deletions(-) diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 222ee98c0d..4694b5cba5 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -29,7 +29,12 @@ #include #include #include - +#include +#include +#include +#include +#include +#include DECLARE_GLOBAL_DATA_PTR; #define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \ @@ -239,6 +244,60 @@ int board_phy_config(struct phy_device *phydev) return 0; } +#if defined(CONFIG_VIDEO_IPUV3) +static struct fb_videomode const hdmi = { + .name = "HDMI", + .refresh = 60, + .xres = 1024, + .yres = 768, + .pixclock = 15385, + .left_margin = 220, + .right_margin = 40, + .upper_margin = 21, + .lower_margin = 7, + .hsync_len = 60, + .vsync_len = 10, + .sync = FB_SYNC_EXT, + .vmode = FB_VMODE_NONINTERLACED +}; + +int board_video_skip(void) +{ + int ret; + + ret = ipuv3_fb_init(&hdmi, 0, IPU_PIX_FMT_RGB24); + + if (ret) + printf("HDMI cannot be configured: %d\n", ret); + + imx_enable_hdmi_phy(); + return ret; +} + +static void setup_display(void) +{ + struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR; + int reg; + + enable_ipu_clock(); + imx_setup_hdmi(); + + reg = readl(&mxc_ccm->chsccdr); + reg |= (CHSCCDR_CLK_SEL_LDB_DI0 + << MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET); + writel(reg, &mxc_ccm->chsccdr); +} +#endif /* CONFIG_VIDEO_IPUV3 */ + +/* + * Do not overwrite the console + * Use always serial for U-Boot console + */ +int overwrite_console(void) +{ + return 1; +} + int board_eth_init(bd_t *bis) { int ret; @@ -255,6 +314,9 @@ int board_eth_init(bd_t *bis) int board_early_init_f(void) { setup_iomux_uart(); +#if defined(CONFIG_VIDEO_IPUV3) + setup_display(); +#endif return 0; } diff --git a/include/configs/mx6sabre_common.h b/include/configs/mx6sabre_common.h index 53cc559295..dd93fffab0 100644 --- a/include/configs/mx6sabre_common.h +++ b/include/configs/mx6sabre_common.h @@ -20,6 +20,7 @@ #define CONFIG_MX6 #include "mx6_common.h" +#include #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DISPLAY_BOARDINFO @@ -32,7 +33,7 @@ #define CONFIG_REVISION_TAG /* Size of malloc() pool */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) +#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M) #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_BOARD_LATE_INIT diff --git a/include/configs/mx6sabresd.h b/include/configs/mx6sabresd.h index 76675f4136..5637c19025 100644 --- a/include/configs/mx6sabresd.h +++ b/include/configs/mx6sabresd.h @@ -17,6 +17,9 @@ #ifndef __MX6QSABRESD_CONFIG_H #define __MX6QSABRESD_CONFIG_H +#include +#include + #define CONFIG_MACH_TYPE 3980 #define CONFIG_MXC_UART_BASE UART1_BASE #define CONFIG_CONSOLE_DEV "ttymxc0" @@ -31,4 +34,20 @@ #define CONFIG_SYS_MMC_ENV_DEV 1 /* SDHC3 */ #endif +/* Framebuffer */ +#define CONFIG_VIDEO +#define CONFIG_VIDEO_IPUV3 +#define CONFIG_CFB_CONSOLE +#define CONFIG_VGA_AS_SINGLE_DEVICE +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE +#define CONFIG_VIDEO_BMP_RLE8 +#define CONFIG_SPLASH_SCREEN +#define CONFIG_SPLASH_SCREEN_ALIGN +#define CONFIG_BMP_16BPP +#define CONFIG_VIDEO_LOGO +#define CONFIG_VIDEO_BMP_LOGO +#define CONFIG_IPUV3_CLK 260000000 +#define CONFIG_IMX_HDMI + #endif /* __MX6QSABRESD_CONFIG_H */ -- cgit v1.2.1 From a11f18737c996a737b85be46b2e8363b7fa2659c Mon Sep 17 00:00:00 2001 From: Robert Winkler Date: Wed, 24 Jul 2013 17:57:06 -0700 Subject: imx: Add documentation for imx specific commands CONFIG_CMD_HDMIDETECT CONFIG_CMD_BMODE Signed-off-by: Robert Winkler Acked-by: Otavio Salvador --- README | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/README b/README index bcfffc3695..657faaa0d9 100644 --- a/README +++ b/README @@ -2598,6 +2598,21 @@ CBFS (Coreboot Filesystem) support Note: There is also a sha1sum command, which should perhaps be deprecated in favour of 'hash sha1'. +- Freescale i.MX specific commands: + CONFIG_CMD_HDMIDETECT + This enables 'hdmidet' command which returns true if an + HDMI monitor is detected. This command is i.MX 6 specific. + + CONFIG_CMD_BMODE + This enables the 'bmode' (bootmode) command for forcing + a boot from specific media. + + This is useful for forcing the ROM's usb downloader to + activate upon a watchdog reset which is nice when iterating + on U-Boot. Using the reset button or running bmode normal + will set it back to normal. This command currently + supports i.MX53 and i.MX6. + - Signing support: CONFIG_RSA -- cgit v1.2.1 From 10f779da54b8a8c85df6d58592c40836d8e7ed49 Mon Sep 17 00:00:00 2001 From: Robert Winkler Date: Tue, 23 Jul 2013 15:07:56 -0700 Subject: imx: nitrogen6x: mx6qsabrelite: Add support for DVI monitors A little background is probably appropriate for this patch. Since "the beginning" of usage of the SABRE Lite and Nitrogen6x boards, DVI detection has been somewhat broken. Some (most) DVI monitors don't produce the "HPD" bit in the PHY_STAT0 register, but do show proper toggling of the RX_SENSE0..3 bits. Creating a new the bit-mask to include all five bits and modifying the 'hdmidet' command and internal detection routines allows these monitors to function properly in U-Boot. A related patch to our kernels allows things to work under Linux: https://github.com/boundarydevices/linux-imx6/commit/7d8752905c118af9063738a533227de0b2f6ecd4 Signed-off-by: Robert Winkler Acked-by: Stefano Babic --- arch/arm/imx-common/cmd_hdmidet.c | 3 +-- arch/arm/include/asm/arch-mx6/mxc_hdmi.h | 3 +++ board/boundary/nitrogen6x/nitrogen6x.c | 2 +- 3 files changed, 5 insertions(+), 3 deletions(-) diff --git a/arch/arm/imx-common/cmd_hdmidet.c b/arch/arm/imx-common/cmd_hdmidet.c index 794bf50cb6..ce0b26e973 100644 --- a/arch/arm/imx-common/cmd_hdmidet.c +++ b/arch/arm/imx-common/cmd_hdmidet.c @@ -27,8 +27,7 @@ static int do_hdmidet(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - u8 reg = readb(&hdmi->phy_stat0) & HDMI_PHY_HPD; - return (reg&HDMI_PHY_HPD) ? 0 : 1; + return (readb(&hdmi->phy_stat0) & HDMI_DVI_STAT) ? 0 : 1; } U_BOOT_CMD(hdmidet, 1, 1, do_hdmidet, diff --git a/arch/arm/include/asm/arch-mx6/mxc_hdmi.h b/arch/arm/include/asm/arch-mx6/mxc_hdmi.h index 5cd6aa6359..2d93658434 100644 --- a/arch/arm/include/asm/arch-mx6/mxc_hdmi.h +++ b/arch/arm/include/asm/arch-mx6/mxc_hdmi.h @@ -901,6 +901,9 @@ enum { HDMI_PHY_HPD = 0x02, HDMI_PHY_TX_PHY_LOCK = 0x01, +/* Convenience macro RX_SENSE | HPD */ + HDMI_DVI_STAT = 0xF2, + /* PHY_I2CM_SLAVE_ADDR field values */ HDMI_PHY_I2CM_SLAVE_ADDR_PHY_GEN2 = 0x69, HDMI_PHY_I2CM_SLAVE_ADDR_HEAC_PHY = 0x49, diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c index 1b82633944..ff033dae71 100644 --- a/board/boundary/nitrogen6x/nitrogen6x.c +++ b/board/boundary/nitrogen6x/nitrogen6x.c @@ -477,7 +477,7 @@ struct display_info_t { static int detect_hdmi(struct display_info_t const *dev) { struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; - return readb(&hdmi->phy_stat0) & HDMI_PHY_HPD; + return readb(&hdmi->phy_stat0) & HDMI_DVI_STAT; } static void do_enable_hdmi(struct display_info_t const *dev) -- cgit v1.2.1 From 4acb4d391f005c0c72f7b84041b3884e4260a5a4 Mon Sep 17 00:00:00 2001 From: Eric Nelson Date: Fri, 26 Jul 2013 17:53:45 -0700 Subject: mxc_ipuv3: fix memory alignment of framebuffer The frame-buffer on i.MX boards needs to be aligned for DMA. Signed-off-by: Eric Nelson --- drivers/video/mxc_ipuv3_fb.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/video/mxc_ipuv3_fb.c b/drivers/video/mxc_ipuv3_fb.c index ace226cece..d922d5d099 100644 --- a/drivers/video/mxc_ipuv3_fb.c +++ b/drivers/video/mxc_ipuv3_fb.c @@ -415,8 +415,9 @@ static int mxcfb_map_video_memory(struct fb_info *fbi) fbi->fix.smem_len = fbi->var.yres_virtual * fbi->fix.line_length; } - - fbi->screen_base = (char *)malloc(fbi->fix.smem_len); + fbi->fix.smem_len = roundup(fbi->fix.smem_len, ARCH_DMA_MINALIGN); + fbi->screen_base = (char *)memalign(ARCH_DMA_MINALIGN, + fbi->fix.smem_len); fbi->fix.smem_start = (unsigned long)fbi->screen_base; if (fbi->screen_base == 0) { puts("Unable to allocate framebuffer memory\n"); -- cgit v1.2.1