summaryrefslogtreecommitdiffstats
path: root/nand_spl/board
Commit message (Collapse)AuthorAgeFilesLines
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2011-10-044-0/+542
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * 'master' of git://git.denx.de/u-boot-mpc85xx: powerpc/p3060: Add SoC related support for P3060 platform powerpc/85xx: Add support for setting up RAID engine liodns on P5020 powerpc/85xx: Refactor some defines out of corenet_ds.h fm-eth: Add ability for board code to disable a port powerpc/mpc8548: Add workaround for erratum NMG_LBC103 powerpc/mpc8548: Add workaround for erratum NMG_DDR120 powerpc/mpc85xxcds: Fix PCI speed powerpc/mpc8548cds: Fix booting message powerpc/p4080: Add support for secure boot flow powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards powerpc/p2041rdb: remove watch dog related codes powerpc/p2041rdb: updated description of cpld command powerpc/p2041rdb: add more ddr frequencies support powerpc/p2041rdb: set sysclk according to status of physical switch SW1 powerpc/p2041rdb: update cpld reset command according to CPLD 2.0 powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver powerpc/mpc8xxx: Add DDR2 to unified DDR driver powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps() powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en powerpc/85xx: Refactor P2041RDB to use common p_corenet files powerpc/85xx: refactor common P-Series CoreNet files for FSL boards powerpc/85xx: Enable CMD_REGINFO on corenet boards powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries powerpc/85xx: Fix USB protocol definitions for P1020RDB powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM powerpc/mpc8xxx: Move DDR RCW overriding to common code powerpc/mpc8xxx: Extend CWL table powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536 powerpc/85xx: Cleanup extern in corenet_ds board code powerpc/p2041rdb: Add ethernet support on P2041RDB board powerpc/85xx: Add networking support to P1023RDS powerpc/hydra: Add ethernet support on P5020/P3041 DS boards powerpc/85xx: Add FMan ethernet support to P4080DS powerpc/85xx: Add support for FMan ethernet in Independent mode powerpc/mpc8548cds: Cleanup mpc8548cds.c powerpc/mp: add support for discontiguous cores powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries fdt: Add new fdt_create_phandle helper fdt: Rename fdt_create_phandle to fdt_set_phandle powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010) powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC) fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010) powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB nand: Freescale Integrated Flash Controller NAND support powerpc/85xx: Add basic support for P1010RDB powerpc/85xx: Add support for new P102x/P2020 RDB style boards powerpc/85xx: relocate CCSR before creating the initial RAM area powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0 powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
| * powerpc/85xx: Add NAND/NAND_SPL support to P1010RDBDipen Dudhat2011-09-292-0/+271
| | | | | | | | | | | | | | | | | | And various defines to enable NAND support and NAND spl code for the P1010RDB platform. Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
| * powerpc/85xx: Add support for new P102x/P2020 RDB style boardsLi Yang2011-09-292-0/+271
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following boards share a common design but with minor variations between them: P1020MSBG-PC P1020RDB-PC P1020UTM-PC P1021RDB-PC P1024RDB P1025RDB P2020RDB-PC The P1020RDB-PC shares its roots in the existing P1020RDB board design, however uses DDR3 instead of DDR2. P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK. Key features on these boards include: * DDR3 * NOR flash * NAND flash (on RDB's only) * SPI flash (on RDB's only) * SDHC/MMC card slot * VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB) * PCIE slot and mini-PCIE slots As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM is used to store SPD data. In case of absent or corrupted SPD, falling back to timing data embedded in the source code will be used. Raw timing data is extracted from DDR chip datasheet. Different speeds of DDR are supported with this approach. ODT option is forced to fit this set of boards, again because they don't have regular DIMMs. CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet specification for writing timing. VSC firmware Address is defined by default in config file for eTSEC1. SD width is based off DIP switch. DIP switch is detected on the board by reading i2c bus and setting the appropriate mux values. Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC have pins multiplexing. QE function needs to be disabled to access Nor Flash and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe" in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below 'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD. 'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Zhao Chenhui <b26998@freescale.com> Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Tang Yuantian <b29983@freescale.com> Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Xie Xiaobo <X.Xie@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com> Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
* | MX31: mx31pdk: Remove nand_spl config.mk fileFabio Estevam2011-09-302-2/+1
|/ | | | | | | No need to have a config.mk to only store a single line. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Stefano Babic <sbabic@denx.de>
* ARM: hawkboard_nand: fix compilation of nand_splStefano Babic2011-09-101-3/+18
| | | | | | get_ram_size() is called, but memsize.c is not compiled. Signed-off-by: Stefano Babic <sbabic@denx.de>
* Convert ISO-8859 files to UTF-8Albert ARIBAUD2011-08-041-1/+1
| | | | | | | | There was a mix of UTF-8 and ISO-8859 files in the U-Boot source tree, which could cause issues with the patchwork review system. This commit converts all ISO-8859 files to UTF-8. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* replace CONFIG_PRELOADER with CONFIG_SPL_BUILDAneesh V2011-07-263-6/+6
| | | | | | replace all occurences of CONFIG_PRELOADER with CONFIG_SPL_BUILD Signed-off-by: Aneesh V <aneesh@ti.com>
* powerpc/85xx: Add basic support for P1023RDS boardRoy Zang2011-07-112-0/+231
| | | | | | | | | | | | | | The P1023RDS board is the reference board for the P1023 SoC. Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe, UART, I2C, etc. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Signed-off-by: Lei Xu <B33228@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Add _end for the end of u-boot image for SMDK6400seedshope2011-05-261-0/+2
| | | | | | | | Since we rename _end to __bss_end__, But we need add _end symbol for the end of u-boot image. Signed-off-by: Zhong Hongbo <bocui107@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Fix the issue of _end symbol not being found while buildingSughosh Ganu2011-04-271-0/+2
| | | | | | Fix the nand_spl build for the hawkboard Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
* MX25: tx25: Add _end section on nand_splFabio Estevam2011-04-271-0/+2
| | | | | | | | | Commit f326cbb (arm: fix incorrect monitor protection region in FLASH) missed to update nand_spl/board/karo/tx25/u-boot.lds. Add the _end section. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* MX31: mx31pdk: fix nand_splStefano Babic2011-04-271-0/+2
| | | | | | | | | | Commit f326cbba98bae21d41df8daac0bd78121d557af1 breaks mx31pdk, as the _end section in u-boot.lds is missing for the nand_spl production. Signed-off-by: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* powerpc/85xx: Modify NAND loader makefiles to compile NAND_SPL linker scriptDipen Dudhat2011-04-154-16/+28
| | | | | | | | | Modify eLBC based platform's NAND loader Makefile to preprocess nand loader linker script and then use it. Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com> CC: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fix build issues cause by LDFLAGS_FINAL changesWolfgang Denk2011-03-3116-48/+48
| | | | | | | | | | | Commit 6dc1ece "Introduce a new linker flag LDFLAGS_FINAL" modified a number of Makefiles in a way that broke out-of-tree builds. The problem was that $(nandobj) was used before it got defined. Fix this. Signed-off-by: Wolfgang Denk <wd@denx.de> Signed-off-by: Scott Wood <scottwood@freescale.com>
* SMDK6400: Add some labels to u-boot.lds to support nand_splseedshope2011-03-271-1/+16
| | | | | | | | In the nand_spl feature of SMDK6400. Add some relocation symbols to nand_spl/board/samsung/smdk6400/u-boot.lds to fix the compile error. Signed-off-by: Zhong Hongbo <bocui107@gmail.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* rename _end to __bss_end__Po-Yu Chuang2011-03-2712-15/+15
| | | | | | | Currently, _end is used for end of BSS section. We want _end to mean end of u-boot image, so we rename _end to __bss_end__ first. Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
* Introduce a new linker flag LDFLAGS_FINALHaiying Wang2011-03-2216-19/+32
| | | | | | | | | | | | | | | commit 8aba9dceebb14144e07d19593111ee3a999c37fc Divides variable of linker flags to LDFLAGS-u-boot and LDFLAGS breaks the usage of --gc-section to build nand_spl. We still need linker option --gc-section for every uboot image, not only the main one. LDFLAGS_FINAL passes the --gc-sections to each uboot image. To get the proper linker flags, we use LDFLAGS and LDFLAGS_FINAL to replace PLATFORM_LDFLAGS in the Makefile of each nand_spl board. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
* mx31pdk: Use the new relocation schemeFabio Estevam2011-02-211-7/+52
| | | | Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
* powerpc/85xx: Add support for booting from NAND on MPC8572DSKumar Gala2011-01-142-0/+215
| | | | | | | | Mimic support that exists on MPC8536DS on the MPC8572DS to allow booting from NAND. Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* PowerPC, nand_spl: Add relocation support for -fpicJoakim Tjernlund2010-12-173-3/+9
| | | | | | | | | | | By rearranging the linker script we get support for relocation of -fpic for free. Move __got2_entries outside _GOT2_TABLE_ defining scope matching the rest of PowerPC Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se> Acked-by: Scott Wood <scottwood@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* powerpc/nand spl: link libgccScott Wood2010-12-168-8/+8
| | | | | | | | | | | | | | | | Recent GCC (4.4+) performs out-of-line epilogues in some cases, when optimizing for size. It causes a link error for _restgpr_30_x (and similar) if libgcc is not linked. It actually increases size with very small binaries, due to the fixed size of the out-of-line code, and not having any functions that actually need to restore more than 2 or 3 registers. But I don't see a way to turn it off, other than asking GCC to optimize for speed -- which may also increase size for some boards. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com> Acked-by: Wolfgang Denk <wd@denx.de>
* Davinci 8xx: Move common functions to share codeStefano Babic2010-11-301-3/+3
| | | | | | | | | | | | | | | | | As more Davinci 8xx board can be added, move common code to be shared between boards. * rebased ontop of Sugosh's patches * moving the HAWKBOARD_KICK{0,1}_UNLOCK defines to arch/arm/include/asm/arch-davinci/davinci_misc.h from to arch/arm/include/asm/arch-davinci/da8xx_common.h * don't define dram functions in PRELOADER * move sync_env_enetaddr into existing EMAC ifdef * use misc.c in hawkboard nand_spl Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Add board support for hawkboardSughosh Ganu2010-11-302-0/+216
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The patch adds basic board support for TI's OMAP-L138 based Hawkboard. This board is pretty similar to the da850 EVM. Support for nand and network access is added in this version. The following bootup procedure is used. At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand controllers and copies the second stage bootloader(nand_spl) to RAM. The secondary bootloader then copies u-boot from a predefined location in the nand flash to the RAM, and passes control to the u-boot image. Three config options are supported * hawkboard_config - Used to create the u-boot.bin. Tftp the u-boot.bin image to the RAM from u-boot, and flash to the nand flash at address 0xe0000. * hawkboard_nand_config - Used to generate the secondary bootloader(nand_spl) image. This creates an elf file u-boot-spl under nand_spl/. Create an AIS signed image using this file, and flash it to the nand flash at address 0x20000. The ais file should fit in one block. * hawkboard_uart_config - This is same as the first image, but with the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* Remove board_init_f function from nand_boot.cSughosh Ganu2010-11-281-1/+5
| | | | | | | | | | | | | Remove the board_init_f function from nand_spl/nand_boot.c. This function is to be defined by all boards using the nand_spl functionality in their individual board directory. Currently this function was being used by the smdk6400 board. Added the board specific function definition. Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
* 83xx: Cleanup for partial linking and --gc-sectionsWolfgang Denk2010-11-272-6/+8
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Haiying Wang <r54964@freescale.com>
* ppc4xx: Cleanup for partial linking and --gc-sectionsWolfgang Denk2010-11-275-6/+6
| | | | | | | | | | | | | | | | | This commit adapts 4xx boards for partial linking with --gc-sections. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Tirumala Marri <tmarri@apm.com> Cc: David Updegraff <dave@cray.com> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Cc: Dirk Eibach <eibach@gdsys.de> Cc: Larry Johnson <lrj@acm.org> Cc: Peter De Schrijver <p2@mind.be> Cc: Niklaus Giger <niklaus.giger@netstal.com> Cc: Daniel Poirot <dan.poirot@windriver.com> Acked-by: Stefan Roese <sr@denx.de>
* 83xx: Fix NAND_SPL link addressScott Wood2010-11-273-6/+6
| | | | | | | | | | | | | | | | | Apply the same fix for 83xx as was done for 85xx in commit 96196a1f7546904563994d2d041804a816d7c139. Without this, NAND SPLs are built with the text base intended for the main image, resulting in a broken, very large u-boot-nand.bin. The block of defines for NAND boot is moved closer to where CONFIG_SYS_TEXT_BASE is defined. We can't directly use CONFIG_SYS_NAND_U_BOOT_DST in the definition of CONFIG_SYS_TEXT_BASE because autoconf.mk will include the literal text "CONFIG_SYS_NAND_U_BOOT_DST", but at least keep them close and point out that they're supposed to be the same. Signed-off-by: Scott Wood <scottwood@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2010-11-171-21/+19
|\
| * tx25: fix linker file for newer ld supportAlbert Aribaud2010-11-171-21/+19
| | | | | | | | | | | | | | | | | | older ld emitted all ELF relocations in input sections named .rel.dyn, whereas newer ld uses names of the form .rel*. The linker script only collected .rel.dyn input sections. Rewrite to collect all .rel* input sections. Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
* | powerpc/85xx: add CONFIG_SYS_TEXT_BASE_SPL for 85xx nand spl buildHaiying Wang2010-11-123-6/+6
|/ | | | | | | | | | Introduce a SPL specific CONFIG_SYS_TEXT_BASE_SPL define to be used by the linker. This has similiar semantics to CONFIG_SYS_TEXT_BASE however since SPL is a unqiue image we introduce a new variable to control its text base address. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Merge branch 'elf_reloc'Wolfgang Denk2010-10-191-0/+13
|\ | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/include/asm/config.h board/LaCie/edminiv2/config.mk board/karo/tx25/config.mk board/logicpd/imx27lite/config.mk doc/README.arm-relocation Signed-off-by: Wolfgang Denk <wd@denx.de>
| * arm926ejs, tx25: add support for ELF relocationsHeiko Schocher2010-10-131-0/+13
| | | | | | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* | Rename TEXT_BASE into CONFIG_SYS_TEXT_BASEWolfgang Denk2010-10-1820-44/+44
|/ | | | | | | | | | | | The change is currently needed to be able to remove the board configuration scripting from the top level Makefile and replace it by a simple, table driven script. Moving this configuration setting into the "CONFIG_*" name space is also desirable because it is needed if we ever should move forward to a Kconfig driven configuration system. Signed-off-by: Wolfgang Denk <wd@denx.de>
* ppc4xx: Big header cleanup, mostly PPC440 relatedStefan Roese2010-09-231-1/+1
| | | | | | | | | | | This patch starts a bit PPC4xx header cleanup. First patch mostly touches PPC440 files. A later patch will touch the PPC405 files as well. This cleanup is done by creating header files for all SoC versions and moving the SoC specific defines into these special headers. This way the common header ppc405.h and ppc440.h can be cleaned up finally. Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Move ppc4xx headers to powerpc include directoryStefan Roese2010-09-232-2/+2
| | | | | | | | | This patch moves some ppc4xx related headers from the common include directory (include/) to the powerpc specific one (arch/powerpc/include/asm/). This way to common include directory is not so cluttered with files. Signed-off-by: Stefan Roese <sr@denx.de>
* ARM: implement relocation for ARM926Heiko Schocher2010-09-191-1/+13
| | | | | | | | | | | | | | | | | | | | | Change the implementation for arm926 to relocate the code to an arbitrary address in RAM. Adapt the TX25 (i.MX25), magnesium board to test the changes. On the tx25 board TEXT_BASE is set to the final relocation address to prevent one more copying of u-boot code when relocating. More info see: doc/README.arm-relocation da850 board: Tested-by: Ben Gardiner <bengardiner@nanometrics.ca> Portions of this work were supported by funding from the CE Linux Forum. Signed-off-by: Heiko Schocher <hs@denx.de> Cc: Ben Gardiner <bengardiner@nanometrics.ca>
* 83xx/85xx/86xx: LBC register cleanupBecky Bruce2010-07-161-3/+2
| | | | | | | | | | | | | | | | | | | | | Currently, 83xx, 86xx, and 85xx have a lot of duplicated code dedicated to defining and manipulating the LBC registers. Merge this into a single spot. To do this, we have to decide on a common name for the data structure that holds the lbc registers - it will now be known as fsl_lbc_t, and we adopt a common name for the immap layouts that include the lbc - this was previously known as either im_lbc or lbus; use the former. In addition, create accessors for the BR/OR regs that use in/out_be32 and use those instead of the mismash of access methods currently in play. I have done a successful ppc build all and tested a board or two from each processor family. Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org> Acked-by: Kim Phillips <kim.phillips@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move arch/ppc to arch/powerpcStefan Roese2010-04-2111-49/+49
| | | | | | | | | | | | | | | | | As discussed on the list, move "arch/ppc" to "arch/powerpc" to better match the Linux directory structure. Please note that this patch also changes the "ppc" target in MAKEALL to "powerpc" to match this new infrastructure. But "ppc" is kept as an alias for now, to not break compatibility with scripts using this name. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Wolfgang Denk <wd@denx.de> Acked-by: Detlev Zundel <dzu@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Anatolij Gustschin <agust@denx.de>
* arm: Move cpu/$CPU to arch/arm/cpu/$CPUPeter Tyser2010-04-133-6/+6
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* ppc: Move cpu/$CPU to arch/ppc/cpu/$CPUPeter Tyser2010-04-1311-37/+37
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Replace "#include <asm-$ARCH/$FILE>" with "#include <asm/$FILE>"Peter Tyser2010-04-132-2/+2
| | | | | | | | | | The appropriate include/asm-$ARCH directory should already by symlinked to include/asm so using the whole "asm-$ARCH" path is unnecessary. This change should also allow us to move the include/asm-$ARCH directories into their appropriate lib/$ARCH/ directories. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Move lib_$ARCH directories to arch/$ARCH/libPeter Tyser2010-04-136-12/+12
| | | | | | | | | Also move lib_$ARCH/config.mk to arch/$ARCH/config.mk This change is intended to clean up the top-level directory structure and more closely mimic Linux's directory organization. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Create CPUDIR variablePeter Tyser2010-04-133-6/+6
| | | | | | | | | | | | The CPUDIR variable points to the location of a target's CPU directory. Currently, it is set to cpu/$CPU. However, using $CPUDIR will allow for more flexibility in the future. It lays the groundwork for reorganizing U-Boot's directory structure to support a layout such as: arch/$ARCH/cpu/$CPU/* (architecture with multiple CPU types) arch/$ARCH/cpu/* (architecture with one CPU type) Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Add support for KARO TX25 boardJohn Rigby2010-03-073-0/+137
| | | | | | | | | | | | | | This is an i.MX25 base board with only NAND so it uses nand_spl to boot. Signed-off-by: John Rigby <jcrigby@gmail.com> Tune configuration, add support for (redundant) environment in NAND. Signed-off-by: Wolfgang Denk <wd@denx.de> Acked-by: Wolfgang Denk <wd@denx.de> CC: Fred Fan <fanyefeng@gmail.com> CC: Tom <Tom.Rix@windriver.com>
* mpc83xx: fix out-of-tree mpc8315 nand buildKim Phillips2010-03-022-0/+160
| | | | | | | | | | | | | | | | commit 2e95004deb6e33e33bf1b8a92a38cd2115bac4c2 "mpc83xx: Add NAND boot support for MPC8315E-RDB boards" symlinked nand_spl/board/freescale/mpc8315erdb to mpc8313erdb in order to not duplicate code. Since the main makefile builds nand_spl/board/$(BOARDDIR) (which makes sense), and the board Makefile and linker script are the only two necessary files to enable out-of-tree building, and other boards have duplicated nand makefiles (e.g. 8536ds & 8569mds), it only seems prudent to copy these two files in the name of the 8315 too. Signed-off-by: Kim Phillips <kim.phillips@freescale.com> Cc: Anton Vorontsov <avorontsov@ru.mvista.com> Cc: Wolfgang Denk <wd@denx.de>
* Nand boot: Add nand boot support for MPC8569mds boardLiu Yu2010-01-272-0/+208
| | | | | | This patch add nand boot support for MPC8569mds board. Signed-off-by: Liu Yu <yu.liu@freescale.com>
* ppc/85xx: Fix compiler warning in nand_spl/.../p1_p2_rdb/nand_boot.cKumar Gala2009-10-261-1/+1
| | | | | | | nand_boot.c: In function 'board_init_f': nand_boot.c:44: warning: 'sys_clk' may be used uninitialized in this function Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* ppc/85xx: Fix building NAND_SPL out of treeKumar Gala2009-10-262-0/+12
| | | | | | | We need to source files to exist in the O=<FOO> nand_spl dir when we build out of tree. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* ppc/P1_P2_RDB: NAND Boot SupportDipen Dudhat2009-10-162-0/+224
| | | | | | | | | NAND Boot support for P1 and P2 series RDB platforms. This patch is derived from NAND Boot support on MPC8536DS. Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxWolfgang Denk2009-09-302-0/+210
|\
OpenPOWER on IntegriCloud