summaryrefslogtreecommitdiffstats
path: root/include/configs/tricorder.h
Commit message (Collapse)AuthorAgeFilesLines
* board:tricorder: fixup SPL OOB layoutAndreas Bießmann2014-04-111-5/+6
| | | | | | | | | | | Commit d016dc42cedbf6102e100fa9ecb58462edfb14f8 changed the layout of BCH8 SW on omap3 boards. We need to adopt the ecc layout for the nand_spl_simle driver to avoid wrong ecc errors. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de> Cc: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* board:tricorder: enable omap_gpio clocksAndreas Bießmann2014-04-111-0/+3
| | | | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de> Cc: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* mtd: nand: omap: remove unused #defines from common omap_gpmc.hpekon gupta2014-03-041-2/+0
| | | | | | | | | | | | | | | | | OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI params or nand_id[] table. And based on that it defines ECC layout. This patch 1) removes following board configs used for defining NAND ECC layout - GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND) - GPMC_NAND_ECC_LP_x8_LAYOUT (for large page x8 NAND) - GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND) - GPMC_NAND_ECC_SP_x8_LAYOUT (for small page x8 NAND) 2) removes unused #defines in common omap_gpmc.h depending on above configs Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5 Signed-off-by: Pekon Gupta <pekon@ti.com>
* Merge branch 'master' of git://git.denx.de/u-boot-nand-flashTom Rini2013-11-251-1/+3
|\
| * mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-schemepekon gupta2013-11-211-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed CONFIG_xx used for selecting NAND ecc-schemes. This patch aims at solving following issues. 1) Currently ecc-scheme is tied to SoC platform, which prevents user to select other ecc-schemes also supported in hardware. like; - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW). - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware supports BCH16 ecc-scheme also. 2) Different platforms use different CONFIG_xx to select ecc-schemes, which adds confusion for user while migrating platforms. - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only 8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW) whereas ELM hardware engine supports other ecc-schemes also like; BCH4, and BCH16 (in future). - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW). - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency on SoC platform and NAND driver. And user can select ecc-scheme independently foreach board. However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand) Signed-off-by: Pekon Gupta <pekon@ti.com>
| * mtd: move & update nand_ecclayout structure (plus board changes)Prabhakar Kushwaha2013-11-211-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | nand_ecclayout is present in mtd.h at Linux. Move this structure to mtd.h to comply with Linux. Also, increase the ecc placement locations to 640 to suport device having writesize/oobsize of 8KB/640B. This means that the maximum oobsize has gone up to 640 bytes and consequently the maximum ecc placement locations have also gone up to 640. Changes from Prabhabkar's version (squashed into one patch to preserve bisectability): - Added _LARGE to MTD_MAX_*_ENTRIES This makes the names match current Linux source, and resolves a conflict between http://patchwork.ozlabs.org/patch/280488/ and http://patchwork.ozlabs.org/patch/284513/ The former was posted first and is closer to matching Linux, but unlike Linux it does not add _LARGE to the names. The second adds _LARGE to one of the names, and depends on it in a subsequent patch (http://patchwork.ozlabs.org/patch/284512/). - Made max oobfree/eccpos configurable, and used this on tricorder, alpr, ASH405, T4160QDS, and T4240QDS (these boards failed to build for me without doing so, due to a size increase). On tricorder SPL, this saves 2576 bytes (and makes the SPL build again) versus the new default of 640 eccpos and 32 oobfree, and saves 336 bytes versus the old default of 128 eccpos and 8 oobfree. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> CC: Vipin Kumar <vipin.kumar@st.com> [scottwood@freescale.com: changes as described above] Signed-off-by: Scott Wood <scottwood@freescale.com> Cc: Thomas Weber <weber@corscience.de> Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Cc: Stefan Roese <sr@denx.de> Cc: York Sun <yorksun@freescale.com> Cc: Tom Rini <trini@ti.com> Reviewed-by: Stefan Roese <sr@denx.de>
* | i2c, omap24xx: convert driver to new mutlibus/mutliadapter frameworkHeiko Schocher2013-11-131-5/+5
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add omap24xx driver to new multibus/multiadpater support - adapted all config files, which uses this driver Tested on the am335x based siemens boards rut, dxr2 and pxm2 posted here: http://patchwork.ozlabs.org/patch/263211/ Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tom Rini <trini@ti.com> Cc: Lars Poeschel <poeschel@lemonage.de> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Thomas Weber <weber@corscience.de> Cc: Tom Rix <Tom.Rix@windriver.com> Cc: Grazvydas Ignotas <notasas@gmail.com> Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com> Cc: Luca Ceresoli <luca.ceresoli@comelit.it> Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Nishanth Menon <nm@ti.com> Cc: Pali Rohár <pali.rohar@gmail.com> Cc: Peter Barada <peter.barada@logicpd.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Michael Jones <michael.jones@matrix-vision.de> Cc: Raphael Assenat <raph@8d.com> Acked-by: Igor Grinberg <grinberg@compulab.co.il> Acked-by: Stefano Babic <sbabic@denx.de>
* Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-091-38/+117
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * tricorder: support 256MiB SDRAM on revision > DAndreas Bießmann2013-11-011-1/+1
| | | | | | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: read kernel directly from NANDAndreas Bießmann2013-11-011-1/+2
| | | | | | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: switch to alternative memtestThomas Weber2013-11-011-2/+4
| | | | | | | | | | | | | | | | Increase the tested memory region for mtest and define CONFIG_SYS_MEMTEST_SCRATCH for CONFIG_SYS_ALT_MEMTEST Signed-off-by: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: Make u-boot fasterThomas Weber2013-11-011-1/+4
| | | | | | | | | | | | | | Silent u-boot and no bootdelay Signed-off-by: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: add led supportAndreas Bießmann2013-11-011-0/+14
| | | | | | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: panic() on unknown boardAndreas Bießmann2013-11-011-0/+7
| | | | | | | | | | | | Also hang() the board on panic(). Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: add tricordereeprom commandAndreas Bießmann2013-11-011-0/+7
| | | | | | | | | | | | | | The new tricordereeprom command can read and write the eeprom for hardware detection on tricorder devices. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: add mtdparts to environmentAndreas Bießmann2013-11-011-5/+4
| | | | | | | | | | | | | | | | Before we always ran 'mtdparts default' which also set the mtdparts and mtdids environment. But if we changed that values by intention we will overwrite them with our default values. This is obviously bad! Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: add cmdline historyAndreas Bießmann2013-11-011-15/+57
| | | | | | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: use generic provided loadaddrAndreas Bießmann2013-11-011-1/+4
| | | | | | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: update flash partitioningAndreas Bießmann2013-11-011-18/+22
| | | | | | | | | | | | | | | | | | The new flash layout respects posible bad blocks in sectors reserved for e.g. SPL, u-boot, kernel, env a.s.o. Additionally this patch prepares for U-Boot Falcon mode for boot time saving. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
| * tricorder: remove lcdmode from bootargsThomas Weber2013-11-011-4/+1
| | | | | | | | | | Signed-off-by: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
* | config: remove platform CONFIG_SYS_HZ definition part 2/2Rob Herring2013-11-041-1/+0
|/ | | | | | Remove platform CONFIG_SYS_HZ definition for configs a-z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* Coding Style cleanup: remove trailing white spaceWolfgang Denk2013-10-141-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARM: OMAP: Add CONFIG_OMAP_COMMONLokesh Vutla2013-08-151-0/+1
| | | | | | | Adding a new CONFIG_OMAP_COMMON which is included by all boards that needs to build cpu/armv7/omap-common folder. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-241-17/+1
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* tricorder: enable hw assisted BCH8 in SPL and u-bootAndreas Bießmann2013-04-081-4/+9
| | | | | | | | Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Cc: Tom Rini <trini@ti.com> Cc: Thomas Weber <weber@corscience.de> Cc: Ilya Yanok <ilya.yanok@cogentembedded.com> Cc: Scott Wood <scottwood@freescale.com>
* ubifs: Allow ubifsmount volume reference by numberJoe Hershberger2013-03-041-1/+1
| | | | | | | | | | | | | | | | | | UBI can mount volumes by name or number The current code forces you to name the volume by prepending every name with "ubi:". >From fs/ubifs/super.c * There are several ways to specify UBI volumes when mounting UBIFS: * o ubiX_Y - UBI device number X, volume Y; * o ubiY - UBI device number 0, volume Y; * o ubiX:NAME - mount UBI device X, volume with name NAME; * o ubi:NAME - mount UBI device 0, volume with name NAME. Now any name passed in any of the above forms are allowed. Also update the configs that referenced ubifsmount. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
* Remove unused CONFIG_SYS_I2C_BUS[_SELECT]Michael Jones2013-01-291-2/+0
| | | | | | | | "CONFIG_SYS_I2C_BUS" and "CONFIG_SYS_I2C_BUS_SELECT" don't appear anywhere outside of config files. Signed-off-by: Michael Jones <michael.jones@matrix-vision.de> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
* Merge branch 'u-boot-ti/master' into 'u-boot-arm/master'Albert ARIBAUD2013-01-081-1/+0
|\ | | | | | | | | This required manual merging drivers/mtd/nand/Makefile and adding am335x_evm support for CONFIG_SPL_NAND_DRIVERS
| * OMAP3: Remove unused PHYS_SDRAM_1_SIZEThomas Weber2012-12-101-1/+0
| | | | | | | | | | | | Remove the unused PHYS_SDRAM_1_SIZE from OMAP3 config files. Signed-off-by: Thomas Weber <thomas@tomweber.eu>
* | spl/nand: introduce CONFIG_SPL_NAND_DRIVERS, _BASE, and _ECC.Scott Wood2012-11-261-0/+3
|/ | | | | | | | | | | | | | Some small SPLs do not use nand_base.c, and a subset of those also require a special driver. Some SPLs need software ECC but others can't fit it. All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these symbols added to preserve existing behavior. Signed-off-by: Scott Wood <scottwood@freescale.com> -- v2: use positive logic for including bits of NAND, rather than a MINIMAL symbol that excludes things.
* configs: Fix usage of mmc rescanAndrew Bradford2012-10-231-1/+1
| | | | | | | | Fix usage of 'mmc rescan' by many configs. Proper use is 'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan the device. 'mmc rescan' itself does not take any arguments. Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
* SPL: Move the omap SPL framework to common/splTom Rini2012-09-271-0/+1
| | | | | | | | | | | | | Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL framework, enable on all of the previously using boards. We move the spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/. We leave the NAND one in-place as we plan to replace it later in this series. We use common/spl to avoid linker problems with respect to merging constant strings in objects. Otherwise all strings in common/ will be linked in and kept which grows SPL in size too much. Signed-off-by: Tom Rini <trini@ti.com>
* ARM: Remove unused stack and irq config definesRob Herring2012-09-011-4/+0
| | | | | | | | | | | CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present in most ARM board config files. IRQs are only enabled for 1 config, so remove the unused config options for IRQ and FIQ stack size as well. Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
* hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.cTom Rini2012-06-201-1/+0
| | | | | | | | | | Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value different than "> " which is vision2. I have Cc'd the maintainer here as I strongly suspect this is a bug rather than intentional behavior. Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de>
* ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORTTom Rini2012-05-151-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | As originally reported against beagleboard we currently have the following error message reported in SPL: U-Boot SPL 2012.04-00020-gb8310b9-dirty (Apr 25 2012 - 18:49:57) Texas Instruments Revision detection unimplemented OMAP SD/MMC: 0 timed out in wait_for_bb: I2C_STAT=1000 reading u-boot.img .... The reason for above message is that when booting from MMC, I2C needs to be initialized to talk with the TWL4030. On OMAP3 I2C is only initalized in SPL if CONFIG_SPL_BOARD_INIT is set. Cc: Thomas Weber <weber@corscience.de> Cc: Steve Sakoman <sakoman@gmail.com> Original patch for Beagleboard is: Signed-off-by: Peter Meerwald <p.meerwald@bct-electronic.com> Extended to cover all other boards: Signed-off-by: Tom Rini <trini@ti.com>
* ARM: omap3: Set SPL stack size to 8KB, image to 54KB.Tom Rini2012-05-151-1/+1
| | | | | | | | | | | | | | | | With older toolchains it is possible to not fit entirely into the 45KB that we had assigned to SPL. Adjust to allow for 8KB of stack (which should be more than required) and 54KB of text/data. Cc: Vaibhav Hiremath <hvaibhav@ti.com> Cc: Nagendra T S <nagendra@mistralsolutions.com> Cc: Thomas Weber <weber@corscience.de> Cc: Ilya Yanok <yanok@emcraft.com> Cc: Steve Sakoman <sakoman@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Signed-off-by: Tom Rini <trini@ti.com> Acked-by: Stefano Babic <sbabic@denx.de> Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
* tricorder: Load kernel from ubifsBernhard Walle2012-04-161-2/+7
| | | | Signed-off-by: Bernhard Walle <walle@corscience.de>
* tricorder: Add UBIFSBernhard Walle2012-04-161-2/+4
| | | | | | | | | | Since kernel should be in a ubifs partition, we need UBIFS. The greater malloc size is needed for UBIFS. Signed-off-by: Bernhard Walle <walle@corscience.de> Squashed two commits (UBIFS enabled and malloc size increased) into one. Signed-off-by: Thomas Weber <weber@corscience.de>
* OMAP3: Remove unused CONFIG_SYS_NAND_ECCSTEPS/TOTALThomas Weber2012-02-271-5/+0
| | | | Signed-off-by: Thomas Weber <weber@corscience.de>
* Tricorder: Switch env to generic mmc driverThomas Weber2012-02-271-3/+4
| | | | | | | | Because the tricorder uses the CONFIG_OMAP_HSMMC the initialization command is mmc rescan and not mmc init. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tom Rini <trini@ti.com>
* OMAP3: Add Corscience Tricorder boardThomas Weber2012-02-121-0/+320
Tricorder is a board which is very similar to the Devkit8000. It is designed as a base platform for further medical devices. www.corscience.de/en/medical-engineering/products/multiparameter/mp10-board.html Signed-off-by: Thomas Weber <weber@corscience.de>
OpenPOWER on IntegriCloud