summaryrefslogtreecommitdiffstats
path: root/include/configs/ls1043ardb.h
Commit message (Collapse)AuthorAgeFilesLines
* armv8: ls1043ardb: enable scsi command and pcie to sata converterPo Liu2016-05-181-0/+21
| | | | | | | Enable scsi command and pcie to sata chip 88SE9170. Signed-off-by: Po Liu <po.liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls1043ardb: invert irq pin polarity for AQR105 PHYShaohui Xie2016-05-181-0/+1
| | | | | | | | | To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity by setting relative bit in SCFG_INTPCR register, because AQR105 interrupt is low active but GIC accepts high active. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* configs: Re-sync with cmd/KconfigTom Rini2016-04-251-2/+0
| | | | | | | Update the config.h and defconfig files for the commands that 8e3c036 converted over to Kconfig Signed-off-by: Tom Rini <trini@konsulko.com>
* configs: Re-sync almost all of cmd/KconfigTom Rini2016-04-251-1/+0
| | | | | | | | This syncs up the current cmd/Kconfig and include/configs/ files with the only exception being CMD_NAND. Due to how we have used this historically we need to take further care here when converting. Signed-off-by: Tom Rini <trini@konsulko.com>
* board: ls1043ardb: Add micro QE support for ls1043ardbZhao Qiang2016-02-241-0/+7
| | | | | Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8/ls1043aqds: add DSPI supportGong Qianyu2016-01-271-10/+0
| | | | | | | | | | | | | | | | | | Enable three DSPI flash memories on board. Commands: => sf probe 1:0 SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB => sf probe 1:1 SF: Detected SST25WF040B with page size 256 Bytes, erase size 4 KiB, total 512 KiB => sf probe 1:2 SF: Detected EN25S64 with page size 256 Bytes, erase size 64 KiB, total 8 MiB Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <york.sun@nxp.com>
* secure_boot: include/configs: make secure boot header file uniformAneesh Bansal2016-01-271-8/+0
| | | | | | | | | | | | | | The file fsl_secure_boot.h must be included in config file for Secure Boot. This is not required to be protected by any macro. CONFIG_FSL_CAAM must be defined and CONFIG_CMD_HASH should be turned on. The above was missing in some config files and all files have been made uniform in this respect. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8/ls1043ardb: add SECURE BOOT target for NORAneesh Bansal2015-12-151-0/+10
| | | | | | | | | | LS1043ARDB Secure Boot Target from NOR has been added. - Configs defined to enable esbc_validate. - ESBC Address in header is made 64 bit. - SMMU is re-configured in Bypass mode. Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls1043ardb: Add support for >2GB memoryShaohui Xie2015-12-131-1/+1
| | | | | | | | This patch also expose the complete DDR region(s) to Linux. Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls1043ardb: add USB supportGong Qianyu2015-11-301-0/+13
| | | | | | | Add support for the third USB controller for LS1043A. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls1043ardb: add DSPI supportGong Qianyu2015-11-301-0/+10
| | | | | | | | Use the U-Boot Driver Model. Just enable Freescale DSPI driver and set DSPI related parameters in dts file. Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls1043ardb: Add sd boot supportGong Qianyu2015-10-291-1/+10
| | | | | Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls1043a: Add Fman supportShaohui Xie2015-10-291-0/+25
| | | | | | | | Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls1043ardb: Add nand boot supportGong Qianyu2015-10-291-0/+46
| | | | | | | | Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com> Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/ls1043ardb: Add LS1043ARDB board supportMingkai Hu2015-10-291-0/+191
LS1043ARDB Specification: ------------------------- Memory subsystem: * 2GByte DDR4 SDRAM (32bit bus) * 128 Mbyte NOR flash single-chip memory * 512 Mbyte NAND flash * 16 Mbyte high-speed SPI flash * SD connector to interface with the SD memory card Ethernet: * XFI 10G port * QSGMII with 4x 1G ports * Two RGMII ports PCIe: * PCIe2 (Lanes C) to mini-PCIe slot * PCIe3 (Lanes D) to PCIe slot USB 3.0: two super speed USB 3.0 type A ports UART: supports two UARTs up to 115200 bps for console Signed-off-by: Hou Zhiqiang <B48286@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
OpenPOWER on IntegriCloud