summaryrefslogtreecommitdiffstats
path: root/include/configs/beagle_x15.h
Commit message (Collapse)AuthorAgeFilesLines
* board: ti: beagle_x15: Rename to indicate support for TI am57xx evmsKipisz, Steven2015-11-181-91/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does actually support two different platform configuration offered by TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728 (or more commonly known as AM5728-evm). Information about the TI AM57xx EVM can be found here http://www.ti.com/tool/tmdxevm5728 The EVM configuration is 1-1 compatible with BeagleBoard X15 with the additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's wlink8 offering. Hence, we rename the beagle_x15 directory to am57xx to support TI EVMs that use the AM57xx processor. By doing this we have common code reuse. This sets the stage to have a common u-boot image solution for multiple TI EVMs such as that already done for am335x and am437x. This sets the stage for upcoming multiple TI EVMs that share the same code base. NOTE: Commit eae7ae185335 ("am437x: Add am57xx_evm_defconfig using CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm platform name. However, this ignored the potential confusion arising for users as a result. To prevent this, existing beagle_x15_defconfig is renamed as am57xx_evm_nodt_defconfig to denote that this is the "non device tree" configuration for the same platform. We still retain am57xx-beagle-x15.dts at this point, since we just require the common minimum dts. As a result of this change, users should expect changes in build procedures('make am57xx_evm_nodt_defconfig' instead of 'make beagle_x15_defconfig'). Hopefully, this would be a one-time change. Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Schuyler Patton <spatton@ti.com> Acked-by: Nishanth Menon <nm@ti.com> Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
* usb: xhci: omap: Remove common dwc3 drv functions callsRamneek Mehresh2015-07-221-0/+1
| | | | | | | Remove all redundant dwc3 driver function calls that are defined by dwc3 driver Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
* Move defaults from config_cmd_default.h to KconfigJoe Hershberger2015-06-251-3/+0
| | | | | | | | | | This sets the default commands Kconfig to match include/config_cmd_default.h commands in the common/Kconfig and removes them from include/configs. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> [trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates] Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: BeagleBoard-X15: Enable VTT regulatorLokesh Vutla2015-06-191-0/+2
| | | | | | | | BeagleBoard-X15 uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. Configuring gpio7_11. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* ARM: BeagleBoard-x15: Enable IO delay recalibration sequenceLokesh Vutla2015-06-121-0/+4
| | | | | | | Enable IO delay recalibration sequence. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* net: Move the CMD_NET config to defconfigsJoe Hershberger2015-06-011-1/+0
| | | | | | | | | | | This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a8 (commands: add more command entries in Kconfig). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
* beagle_x15: increase phy autoneg timeoutSekhar Nori2015-03-131-0/+1
| | | | | | | | | | | | | | When Beagle X15 is connected to Gigabit switch, it takes more time to finish auto-negotiation than on a 10/100 switch. The default 4 second limit times-out more often than not. This is observed when testing with a D-Link DGS-1008A desktop switch. Increase the auto-negotiation time-out for Beagle-X15 to handle this case. Signed-off-by: Sekhar Nori <nsekhar@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* beagle_x15: enable NFS commandFelipe Balbi2015-01-051-0/+1
| | | | | | | | NFS is useful for loading zImage and dts through NFS export. It saves us from running two services for loading files over the network (tftp and nfs). Signed-off-by: Felipe Balbi <balbi@ti.com>
* TI: armv7: enable UUID and PARTNishanth Menon2015-01-051-2/+0
| | | | | | | | | Enable UUID and partition support for scripted handling platforms with MMC and eMMC and varied partitioning schemes And remove it from headers that end up redefining it. Signed-off-by: Nishanth Menon <nm@ti.com>
* beagle_x15: add board support for Beagle x15Felipe Balbi2014-12-041-0/+88
BeagleBoard-X15 is the next generation Open Source Hardware BeagleBoard based on TI's AM5728 SoC featuring dual core 1.5GHZ A15 processor. The platform features 2GB DDR3L (w/dual 32bit busses), eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60), separate LCD port, video In port, 4GB eMMC, uSD, Analog audio in/out, dual 1G Ethernet. For more information, refer to: http://www.elinux.org/Beagleboard:BeagleBoard-X15 Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@ti.com>
OpenPOWER on IntegriCloud