summaryrefslogtreecommitdiffstats
path: root/include/configs/G2000.h
Commit message (Collapse)AuthorAgeFilesLines
* powerpc: Cleanup BOOTFLAG_* referencesPeter Tyser2010-10-181-8/+0
| | | | | | | | | | | | Now that warm booting is not supported, there isn't a need for the BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them. Note that this change makes the board info bd_bootflags field useless. It will always be set to 0, but we leave it around so that we don't break the board info structure that some OSes are expecting to be passed from U-Boot. Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* Makefile: move all Power Architecture boards into boards.cfgWolfgang Denk2010-10-181-0/+2
| | | | | | | | | | Clean up Makefile, and drop a lot of the config.mk files on the way. We now also automatically pick all boards that are listed in boards.cfg (and with all configurations), so we can drop the redundant entries from MAKEALL to avoid building these twice. Signed-off-by: Wolfgang Denk <wd@denx.de>
* ppc4xx: Use common NS16550 driver for PPC4xx UARTStefan Roese2010-09-231-1/+6
| | | | | | | | | | | | | | | | This patch removes the PPC4xx UART driver. Instead the common NS16550 driver is used, since all PPC4xx SoC's use this peripheral device. The file 4xx_uart.c now only implements the UART clock calculation function which also sets the SoC internal UART divisors. All PPC4xx board config headers are changed to use this common NS16550 driver now. Tested on these boards: acadia, canyonlands, katmai, kilauea, sequoia, zeus Signed-off-by: Stefan Roese <sr@denx.de>
* ppc4xx: Big header cleanup part 2, mostly PPC405 relatedStefan Roese2010-09-231-5/+5
| | | | | | | | | | | | | | | This cleanup is done by creating header files for all SoC versions and moving the SoC specific defines into these special headers. This way the common header ppc405.h and ppc440.h can be cleaned up finally. As a part from this cleanup, the GPIO definitions for PPC405EP are corrected. The high and low parts of the registers (for example CONFIG_SYS_GPIO0_OSRL vs. CONFIG_SYS_GPIO0_OSRH) have been defined in the wrong order. This patch now fixes this issue by switching these xxxH and xxxL values. This brings the GPIO 405EP port in sync with all other PPC4xx ports. Signed-off-by: Stefan Roese <sr@denx.de>
* i2c: Move PPC4xx I2C driver into drivers/i2c directoryStefan Roese2010-04-061-0/+1
| | | | | | | | This patch moves the PPC4xx specific I2C device driver into the I2C drivers directory. All 4xx config headers are updated to include this driver. Signed-off-by: Stefan Roese <sr@denx.de>
* Remove legacy NAND and disk on chip references from boards.Scott Wood2009-07-171-20/+0
| | | | Signed-off-by: Scott Wood <scottwood@freescale.com>
* ppc4xx: Remove CONFIG_SYS_IGNORE_405_UART_ERRATA_59 from config filesMatthias Fuchs2009-01-261-1/+0
| | | | | | | | | Lot's of 405 board config files use CONFIG_SYS_IGNORE_405_UART_ERRATA_59. Either they define or undef it. Because it's not used in any source files this patch removes any references to it. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
* NAND: rename NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPSWolfgang Grandegger2009-01-231-1/+0
| | | | | | | | | | | | | | | | This patch renames NAND_MAX_CHIPS to CONFIG_SYS_NAND_MAX_CHIPS and changes the default from 8 to 1 for the legacy and the new MTD NAND layer. This allows to remove all NAND_MAX_CHIPS definitions in the board config files because none of the boards use multi chip support (NAND_MAX_CHIPS > 1) so far. The bamboo and the DU440 define #define NAND_MAX_CHIPS CONFIG_SYS_MAX_NAND_DEVICE but that's bogus and did not work anyhow. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
* Changed PPC4xx EMAC driver to require CONFIG_PPC4xx_EMACBen Warren2008-11-091-0/+1
| | | | | | | All in-tree IBM/AMCC PPC4xx boards using the EMAC get this new CONFIG Signed-off-by: Ben Warren <biggerbadderben@gmail.com> Acked-by: Stefan Roese <sr@denx.de>
* rename CFG_ macros to CONFIG_SYSJean-Christophe PLAGNIOL-VILLARD2008-10-181-103/+103
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* Remove unused CFG_EEPROM_PAGE_WRITE_ENABLE referencesPeter Tyser2008-10-141-1/+0
| | | | Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
* rename CFG_ENV macros to CONFIG_ENVJean-Christophe PLAGNIOL-VILLARD2008-09-101-4/+4
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASHJean-Christophe PLAGNIOL-VILLARD2008-09-101-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* rename CFG_ENV_IS_IN_EEPROM in CONFIG_ENV_IS_IN_EEPROMJean-Christophe PLAGNIOL-VILLARD2008-09-101-1/+1
| | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* ppc4xx: Remove cache definition from 4xx board config filesStefan Roese2007-10-311-10/+0
| | | | | | | All 4xx board config files don't need the cache definitions anymore. These are now defined in common headers. Signed-off-by: Stefan Roese <sr@denx.de>
* include/configs/[A-I]*: Cleanup BOOTP and lingering CFG_CMD_*.Jon Loeliger2007-07-101-0/+9
| | | | | | | | | Explicitly add in default CONFIG_BOOTP_* options where cmd_confdefs.h used to be included but CONFIG_BOOTP_MASK was not defined. Remove lingering references to CFG_CMD_* symbols. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* include/configs: Use new CONFIG_CMD_* in various F* and G* named board ↵Jon Loeliger2007-07-081-16/+19
| | | | | | config files. Signed-off-by: Jon Loeliger <jdl@freescale.com>
* Change all '$(...)' variable references into '${...}'Wolfgang Denk2005-11-201-9/+9
| | | | | | which makes the environment compatible with the hush shell. WARNING: Support for the old '$(...)' syntax will be discontinued in a later version.
* Cleanup (PPC4xx is AMCC now)Wolfgang Denk2005-09-231-1/+1
|
* * Code cleanup, mostly for GCC-3.3.xwdenk2004-12-311-0/+1
| | | | | | | | | | | | * Cleanup confusing use of CONFIG_ETH*ADDR - ust his only to pre-define a MAC address; use CONFIG_HAS_ETH* to enable support for additional ethernet addresses. * Cleanup drivers/i82365.c - avoid duplication of code * Fix bogus "cannot span across banks" flash error message * Add support for CompactFlash for the CPC45 Board.
* esd config files updatedstroese2004-12-161-0/+425
OpenPOWER on IntegriCloud